Search Results (931)

This pilot study investigated an automated pilot plant for removing microplastics (MPs) from industrial wastewater that are generated during packaging production. MP removal is based on organosilane-induced agglomeration-fixation (clump & skim technology) followed by separation. The wastewater had high MP loads (1725 ± 377 mg/L; 673 ± 183 million particles/L) and an average COD of 7570 ± 1339 mg/L. Over 25 continuous test runs, the system achieved consistent performance, removing an average of 97.4% of MPs by mass and 99.1% by particle count, while reducing the COD by 78.8%. Projected over a year, this equates to preventing 1.7 tons of MPs and 6 tons of COD from entering the sewage system. Turbidity and photometric TSS measurements proved useful for process control. The approach supports water reuse—with water savings up to 80%—and allows recovery of agglomerates for recycling and reuse. Targeting pollutant removal upstream at the source provides multiple financial and environmental benefits, including lower overall energy demands, higher removal efficiencies, and process water reuse. This provides financial and environmental incentives for industries to implement sustainable solutions for pollutants and microplastic removal. Full article

Sewage sludge (SS) is commonly applied as a soil amendment. This practice has raised concern about the dissemination of emerging pollutants (EPs). EPs include compounds such as flame retardants, plasticizers, pharmaceuticals, and personal care products, among others, which may pose risks to human health and ecosystems. The complexity of the SS matrix, combined to the absence of an international legislation framework, makes it necessary to evaluate the techniques available for detecting these contaminants. Detection is typically performed using sensitive analytical techniques; however, the extraction strategy selected remains a crucial step. This review aims to compile different methodologies for the determination of EPs in SS, focusing on extraction strategies reported between 2010 and 2025. Ultrasound-assisted extraction (UAE), pressurized liquid extraction (PLE), and microwave-assisted extraction (MAE) are the most widely used strategies for EPs. UAE is considered the most preferable option, as it enables the extraction of a wide range of compounds without the need for expensive equipment. Among novel techniques, the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method is especially promising, as it is applicable to multiple target compounds. This review provides up-to-date information that can support the development of routine and standardized methodologies for the characterization of EPs in SS. Full article

Antimicrobial resistance (AMR) has emerged as a planetary health emergency, driven not only by the clinical misuse of antibiotics but also by diverse environmental dissemination pathways. This review critically examines the role of environmental compartments—water, soil, and air—as dynamic reservoirs and transmission routes for antibiotic-resistant bacteria (ARB) and resistance genes (ARGs). Recent metagenomic, epidemiological, and mechanistic evidence demonstrates that anthropogenic pressures—including pharmaceutical effluents, agricultural runoff, untreated sewage, and airborne emissions—amplify resistance evolution and interspecies gene transfer via horizontal gene transfer mechanisms, biofilms, and mobile genetic elements. Importantly, it is not only highly polluted rivers such as the Ganges that contribute to the spread of AMR; even low concentrations of antibiotics and their metabolites, formed during or after treatment, can significantly promote the selection and dissemination of resistance. Environmental hotspots such as European agricultural soils and airborne particulate zones near wastewater treatment plants further illustrate the complexity and global scope of pollution-driven AMR. The synergistic roles of co-selective agents, including heavy metals, disinfectants, and microplastics, are highlighted for their impact in exacerbating resistance gene propagation across ecological and geographical boundaries. The efficacy and limitations of current mitigation strategies, including advanced wastewater treatments, thermophilic composting, biosensor-based surveillance, and emerging regulatory frameworks, are evaluated. By integrating a One Health perspective, this review underscores the imperative of including environmental considerations in global AMR containment policies and proposes a multidisciplinary roadmap to mitigate resistance spread across interconnected human, animal, and environmental domains. Full article

This study investigates the implications of sewage contamination in the coastal and riverine environments of Hout Bay, Cape Town, South Africa. Chemical analyses were applied to quantify the presence of pollutants such as pharmaceutical and personal care products (PPCPs) in sentinel marine organisms such as mussels, as well as microbial indicators of faecal contamination in river water and seawater, for estimating the extent of impact zones in the coastal environment of Hout Bay. This research investigated the persistent pharmaceuticals found in marine outfall wastewater effluent samples in Hout Bay, examining whether these substances were also detectable in marine biota, specifically focusing on Mytilus galloprovincialis mussels. The findings reveal significant levels of sewage-related pollutants in the sampled environments, with concentrations ranging from 32.74 to 43.02 ng/g dry weight (dw) for acetaminophen, up to 384.96 ng/g for bezafibrate, and as high as 338.56 ng/g for triclosan. These results highlight persistent PPCP contamination in marine organisms, with increasing concentrations observed over time, suggesting a rise in population and pharmaceutical use. Additionally, microbial analysis revealed high levels of E. coli in the Hout Bay River, particularly near stormwater from the Imizamo Yethu settlement, with counts exceeding 8.3 million cfu/100 mL. These findings underscore the significant impact of untreated sewage on the environment. This study concludes that current sewage treatment is insufficient to mitigate pollution, urging the implementation of more effective wastewater management practices and long-term monitoring of pharmaceutical levels in marine biota to protect both the environment and public health. Full article

Honey processing is closely linked to water pollution due to the lack of a specific wastewater treatment. This study proposes a sustainable and innovative solution based on two sequential bioprocesses using a real effluent from an Argentine honey-exporting facility. In the initial stage, the honey wastewater was enriched with a non-Saccharomyces yeast (Candida ethanolica), isolated from the same effluent. Treatment with this yeast in a bioreactor nearly doubled the total sugar removal efficiency compared to the control (native flora). Subsequent clarification with diatomaceous earth reduced the optical density (91.6%) and COD (30.9%). In the second stage, secondary sewage effluent was added to the clarified effluent and inoculated with Chlorella vulgaris under different culture conditions. The best microalgae performance was observed under high light intensity and high inoculum concentration, achieving a fivefold increase in cell density, a specific growth rate of 0.752 d⁻¹, and a doubling time of 0.921 d. Although total sugar removal in this stage remained below 28%, cumulative COD removal reached 90% after nine days under both lighting conditions. This study presents the first integrated treatment approach for honey industry effluents using a native yeast–microalgae system, incorporating in situ effluent recycling and the potential for dual waste valorization. Full article

Untreated sewage sludge (SS) and misused stabilization technologies have contributed to great contamination and the accumulation of various pollutants in agricultural soils. Regarding micro-pollutants’ degradation, scalable and effective technologies are still scarce. Although many attempts at composting adaptations have been discussed, only a few have been tested individually under outdoor conditions. To investigate different composting methods (bioaugmentation and semipermeable cover) for the removal of micro-pollutants frequently found in SS, we performed a set of on-site experiments. Windrows of SS and olive pruning were used as the compostable material and were subjected to (i) bioaugmentation with the fungus Penicillium oxalicum, (ii) covered composting, (iii) covered and bioaugmented composting, and (iv) a conventional composting pile, which was included as a control. The entire experiment lasted 99 days. Bioaugmentation without cover increased the phosphorus content, favored a reduction in heavy metal content, and was the only treatment that reduced carbamazepine at the end of the process. Moreover, the inoculation of P. oxalicum under semipermeable cover increased the richness, diversity, and dominance of specific microbial taxa and total bacterial abundance. The four mature composts obtained met the standards required to be classified in the B fertilizer category, showing that we reduced most of the micro-pollutants, and passed the germination test. Full article

Aquatic plants, as sedentary lifestyle organisms that accumulate chemical substances from their surroundings, can serve as valuable indicators of long-term anthropogenic pressure. In Poland, water monitoring is limited both spatially and temporally, which hampers a comprehensive assessment of water quality. Since the implementation of the Water Framework Directive (WFD), biotic elements, including macrophytes, have played an increasingly important role in water monitoring. Moreover, running waters, due to their dynamic nature, are susceptible to episodic pollution inputs that may be difficult to detect during isolated, point-in-time sampling campaigns. The analysis of stable carbon (δ¹³C) and nitrogen (δ¹⁵N) isotope signatures in macrophytes enables the identification of elemental sources, including potential pollutants. Research conducted between 2008 and 2011 encompassed 38 sites along 15 rivers and 108 sites across 21 lakes in northern Poland. This study focused on the isotope signatures of three pondweed species: Stuckenia pectinata, Potamogeton perfoliatus, and Potamogeton crispus. The results revealed statistically significant differences in the δ¹³C and δ¹⁵N values of plant organic matter between river and lake environments. Higher δ¹⁵N values were observed in rivers, whereas higher δ¹³C values were recorded in lakes. Spearman correlation analysis showed a negative relationship between δ¹³C and δ¹⁵N, as well as correlations between δ¹⁵N and the concentrations of Ca²⁺ and HCO₃⁻. A positive correlation was also found between δ¹³C and dissolved oxygen levels. These findings confirm the utility of δ¹³C and, in particular, δ¹⁵N as indicators of anthropogenic eutrophication, including potentially domestic sewage input and its impact on aquatic ecosystems. Full article

With the large-scale closure of coal mines leading to groundwater pollution, in order to systematically identify the sources of major chemical ions in surface water and groundwater. This study comprehensively applied methods such as Piper’s trilinear diagram, linear fitting, and correlation analysis to quantitatively analyze the hydrochemical characteristics of closed coal mining areas in southwest Shandong and to clarify the sources of geochemical components in surface water and groundwater, and the PMF model was used to analyze the sources of chemical components in mine water and karst water. The results show that the concentrations of TDS ( Total Dissolved Solids), SO₄²⁻, Fe, and Mn in the mine water of the closed coal mine area are higher than in the karst water. Both water bodies are above groundwater quality standards. Ca²⁺, SO₄²⁻, and HCO₃⁻ dominate the ionic components in surface water and different types of groundwater. The hydrochemical types of surface, pore, and mine waters are mainly SO₄-HCO₃-Ca, whereas SO₄-HCO₃-Ca and HCO₃-SO₄-Ca dominate karst waters. SO₄²⁻ is the leading ion in the TDS of water bodies. The mineralization process of surface water is mainly controlled by the weathering of silicate minerals, while that of the groundwater is mainly controlled by the dissolution of carbonate minerals. The impact of mining activities on surface water and groundwater is significant, while the impact of agricultural activities on surface water and groundwater is relatively small. The degree of impact of coal mining activities on SO₄²⁻ concentrations in surface water, pore water, and karst water, in descending order, is karst water, surface water, and pore water. The PMF (Positive Matrix Factorization) model analysis results indicate that dissolution of carbonate minerals with sulphate and oxidation dissolution of sulfide minerals are the main sources of chemical constituents in mine waters. Carbonate dissolution, oxidation dissolution of sulfide minerals, domestic sewage, and dissolution of carbonate minerals with sulphate are ranked as the main sources of chemical constituents in karst water from highest to lowest. These findings provide a scientific basis for the assessment and control of groundwater pollution in the areas of closed coal mines. Full article

Phewa Lake, Nepal’s second-largest natural lake, is under increasing ecological stress due to sedimentation, shoreline encroachment, and water quality decline driven by rapid urban growth, fragile mountainous catchments, and changing climate patterns. This study employs an integrated approach combining sediment yield estimation from its catchment using RUSLE, shoreline encroachment analysis via satellite imagery and historical records, and identification of pollution sources and socio-economic factors through field surveys and community consultations. The results show that steep, sparsely vegetated slopes are the primary sediment sources, with Harpan Khola (a tributary of Phewa Lake) contributing over 80% of the estimated 339,118 tons of annual sediment inflow. From 1962 to 2024, the lake has lost approximately 5.62 sq. km of surface area, primarily due to a combination of sediment deposition and human encroachment. Pollution from untreated sewage, urban runoff, and invasive aquatic weeds further degrades water quality and threatens biodiversity. Based on the findings, this study proposes a way forward to mitigate sedimentation, encroachment, and pollution, along with a sustainable revitalization plan. The approach of this study, along with the proposed sustainability measures, can be replicated in other lake systems within Nepal and in similar watersheds elsewhere. Full article

Domestic wastewater discharge is the major source of pollution in Malaysia. Phytoremediation under hydroponic conditions was initiated to treat domestic wastewater and, at the same time, to resolve the space limitation issue by installing a hydroponic system in vertical space at the site. Water hyacinth (WH) was selected in this study to identify its performance of water hyacinth in removing nutrients in raw sewage under batch operation. In the batch experiment, the ratio of COD_initial/plant_initial was identified, and SPSS ANOVA analysis shows that the number of plant size factors was not statistically different in this study. Therefore, four WH, each with an initial weight of 60 ± 20 g, were recommended for this study. Throughout the 10 days of the batch experiment, the average of COD, BOD, TSS, TP, NH4, and color removal was 73%, 73%, 86%, 79%, 77%, and 54%, respectively. The WH biomass weight increased by an average of 78%. The plants have also improved the DO level from 0.24 mg/L to 4.88 mg/L. However, the pH of effluent decreased from pH 7.05 to pH 4.88 below the sewage Standard B discharge limit of pH 9–pH 5.50. Four WH plant groups were recommended for future study, as the COD removal among the other plant groups is not a statistically significant difference (p < 0.05). Furthermore, the lower plant biomass is preferable for the high pollutant removal performance due to the fact that it can reduce the maintenance and operating costs. Full article

Macro- and microelements in waste can be returned to the soil as fertilizers and their sustainable use can reduce the need to extract natural resources. For example, the use of carbonate-clay flour, sewage sludge and waste sulfate sulfur to improve soil properties enables the natural recycling of the nutrients contained in these materials. Soil physicochemical properties with the application of waste and the bioavailability of nutrients and trace elements were assessed before and after a 3-month incubation period. This study showed that when carbonate-clay flour was applied alone or together with sewage sludge and waste sulfur, it improved the properties of the soil, inducing a reduction in acidification and an increase in the content of available P, K and Mg. Sewage sludge also provided Zn, Cu, Ni and Cr in addition to organic carbon. Sulfate did not cause soil acidification. The results indicate that the use of carbonate-clay flour alone, as well as with the addition of sewage sludge and sulfate sulfur, can be recommended for the deacidification of soil and serve as a remediation tool for, for example, the precipitation of chemical pollutants. The valorization of the waste used fits into the circular economy approach. Full article

Sulfate as a potential pollution source in the water environment of the basin, identifying sulfate sources and migration mechanisms is essential for protecting the water environment and ensuring sustainable water management. Liuyang River is a primary tributary of the Xiangjiang River. It has experienced progressively intensifying anthropogenic influences in recent decades, manifested by sustained sulfate concentration increases. However, the sulfate sources and their contributions were not clear. This study used hydrochemistry and multi-isotopes methods combined with Simmr model to study the hydrochemical characteristics, sulfate sources, and migration–transformation processes of surface water and groundwater. The results showed that the hydrochemical types of surface water were HCO₃-Ca and HCO₃·SO₄-Ca·Mg, and groundwater were HCO₃-Ca, HCO₃-Ca·Mg, and HCO₃·SO₄-Ca. Ions in the water primarily originated from carbonate and silicate rocks dissolution and sulfide oxidation, augmented by mining operations, sewage discharge, and chemical production. The analyses of hydrochemistry, isotopes, and Simmr model revealed that surface water sulfate originated from soil sulfate (35.70%), sulfide oxidation (26.56%), sewage (16.58%), and atmospheric precipitation (12.45%). Groundwater sulfate was derived predominantly from sewage (34.96%), followed by soil sulfate (28.09%), atmospheric precipitation (17.35%), and sulfide oxidation (12.25%). Sulfate migration and transformation were controlled by the natural environment and anthropogenic impacts. When unaffected by human activities, sulfate mainly originated from soil and atmospheric precipitation, relating to topography, geological conditions, agricultural activities, and precipitation intensity. However, in regions with intense human activities, contributions from sewage and sulfide oxidation significantly increased due to the influences of mining and industrial activities. Full article

Microplastics (MPs) are becoming an increasingly common pollutant in the aquatic environment, including stormwater. This is a serious problem, as stormwater is becoming an essential transport route for MPs from urban areas to surface waters. Rainwater flowing from roofs, roads, and other impermeable surfaces contains a variety of plastic particles originating from tire abrasion or waste disposal. This article presents an overview of current research on the occurrence of MPs in stormwater. The potential of selected green infrastructure solutions—particularly bioretention systems, constructed wetlands, and permeable pavements—for their reduction is assessed. Individual solutions present how the change in filter material, selection of vegetation, or the method of conducting the process (e.g., direction of stormwater flow in constructed wetlands) affects their effectiveness. The potential of green infrastructure is also compared with the traditional gray solution of sewage management in cities. This article emphasizes the importance of integrating such solutions in spatial planning as an effective tool to combat climate change and limit the spread of microplastics in the environment. Full article

In recent decades, the River Ganges in India has been heavily contaminated with domestic waste and industrial toxins because of cultural activities, a lack of community awareness, an absence of sewage disposal facilities, and rapid population growth. Previous studies have focused separately on either the physical or social factors associated with River Ganges pollution but have not combined these elements in a single study. To fill this research gap, our study assesses the bio-physical and social vulnerability of the River Ganges by using a holistic approach. The following four sampling stations were selected: Rishikesh, Haridwar, Kanpur, and Varanasi. These locations were chosen to test the water quality in bio-physical aspects and to assess the social perceptions of river vulnerability among the residents and visitors. Perceptions of river water quality and likely sources of pollution were gathered via the distribution of over 1000 questionnaires. Data collection took place in the winter and summer of 2022 and 2023. The results showed that river water quality is not suitable for drinking purposes at any of the four cities without conventional treatment, and that the river is unsuitable for bathing at all locations, except upstream of Rishikesh. Nearly 50% of those questioned agreed that the river is polluted, whilst 74% agreed that pollution has increased in recent decades, particularly in the last 10 years. These compelling results are critical for policymakers and decision makers. They highlight the urgent need for novel strategies that address Ganges pollution while fostering community health education and environmental management. By dispelling myths surrounding river quality, this study strengthens the ongoing efforts to restore the Ganges, ensuring that it remains a vital lifeline for present and future generations. Full article

This study aims to evaluate the potential of Lemna minor (common duckweed) for the removal of galaxolide (HHCB) from polluted water, a compound commonly used in consumer products such as perfumes and detergents. The focus was to identify the optimal conditions for removal, determine the removal efficiency, and elucidate the mechanisms involved. The experiment was conducted by cultivating Lemna minor using as a cultivation medium synthetic sewage and laboratory solutions (MilliQ water) containing galaxolide at two levels of concentration (1034 µg·L⁻¹ and 2326 µg·L⁻¹). The plants were exposed to light for 16 h a day and grown at pH 5. Removal efficiency was assessed through liquid chromatography (HPLC) with fluorescence detection (FLD). Kinetics of observed process was modelled using a pseudo-first-order equation. The study of the HHCB decay mechanism included determining the contributions to the final effect of the following processes occurring simultaneously: sorption on the plant surface, photodegradation, and uptake by Lemna. The removal efficiency (RE%) of galaxolide by Lemna minor was 99.7% when aqueous standard solution was used as the cultivation medium after 14 days, and between 97.8% and 98.6% in the case of wastewater samples. Sorption onto plants surface, photodegradation, and uptake by the plants were identified as the primary mechanisms for HHCB removal. Toxicity studies revealed that galaxolide exposure adversely affected Lemna minor growth, altering photosynthetic pigments (chlorophyll and carotenoid) levels. Full article