Search Results (23)

Thermokinetic characterization of amorphous carbamazepine was performed utilizing non-isothermal differential scanning calorimetry (DSC) and thermogravimetry (TGA). Structural relaxation of the amorphous matrix was described in terms of the Tool–Narayanaswamy–Moynihan model with the following parameters: Δh* ≈ 200–300 kJ·mol⁻¹, β = 0.57, x = 0.44. The crystallization of the amorphous phase was modeled using complex Šesták–Berggren kinetics, which incorporates temperature-dependent activation energy and degree of autocatalysis. The activation energy of the crystal growth was determined to be >320 kJ·mol⁻¹ at the glass transition temperature (T_g). Owing to such a high value, the amorphous carbamazepine is stable at T_g, allowing for extensive processing of the amorphous phase (e.g., self-healing of the quench-induced mechanical defects or internal stress). A discussion was conducted regarding the converse relation between the activation energies of relaxation and crystal growth, which is possibly responsible for the absence of sub-T_g crystal growth modes. The high-temperature thermal decomposition of carbamazepine proceeds via multistep kinetics, identically in both an inert and an oxidizing atmosphere. A complex reaction mechanism, consisting of a series of consecutive and competing reactions, was proposed to explain the second decomposition step, which exhibited a temporary mass increase. Whereas a negligible degree of carbamazepine degradation was predicted for the temperature characteristic of the pharmaceutical hot-melt extrusion (~150 °C), the degradation risk during the pharmaceutical 3D printing was calculated to be considerably higher (1–2% mass loss at temperatures 190–200 °C). Full article

H13 steel, a widely used material in hot work tooling, faces premature failure due to insufficient hardness and wear resistance. To address this limitation, Mo₂FeB₂ cermet coatings were fabricated on H13 alloy steel via plasma spray welding, and subsequently quenched at 850 °C, 1000 °C, and 1150 °C. The effects of the quenching temperature on the microstructure and wear resistance were investigated using optical microscopy (OM) for cross-sectional morphology, scanning electron microscopy (SEM) for microstructural and wear surface analyses, energy-dispersive spectroscopy (EDS) for elemental composition analysis, and X-ray diffraction (XRD) for phase identification. The coating primarily consisted of α-Fe, Mo₂FeB₂, (Mo,Fe,Cr)₃B₂, and Fe₂₃(B,C)₆ phases. Increasing the temperature to 1150 °C increased the Mo₂FeB₂ hard phase and elevated microhardness by 32.04% (from 827 HV_0.5 to 1092 HV_0.5). Wear resistance improved by 46.38% (mass loss reduced from 6.9 mg to 3.7 mg). The main wear mechanism was identified as abrasive wear due to the spalling of hard phase particles. These results demonstrate that optimizing quenching temperature enhances the hardness and wear resistance in Mo₂FeB₂ coatings, offering a viable strategy to extend H13 steel service life in high-temperature industrial applications. Full article

A novel Coulomb spike concept is applied to the radiation damage induced in LiF and SiO₂ with about the same mass density (~2.65 g cm⁻³) by ${}_{28}{}^{60}\mathrm{N}\mathrm{i}$ and ${}_{36}{}^{84}\mathrm{K}\mathrm{r}$ ions of 1.0-MeV u⁻¹ energy for about the same electronic energy loss (~10 MeV µm⁻¹). This is an alternative concept to the already known models of the Coulomb spike and inelastic thermal spike for the damage induced by swift heavy ion irradiations. The distribution of ionizations and electrostatic energy gained in the electric field by the ionized atoms is computed with the PHITS code for both targets. Further, the atomic collision cascades induced by these low-energy hot ions of about 500 eV are simulated with the SRIM2013 code. It is found that melting is reached in a small volume for SiO₂ due to the energy deposition in the subthreshold events of nuclear collisions induced by the Si and O ions. For LiF, the phonon contribution to the stopping power of the lighter Li and F ions is not sufficient to induce melting, even though the melting temperature is lower than for SiO₂. The formation of amorphous domains in SiO₂ is likely after fast quenching of the small molten pockets, whereas only point defects may be formed in LiF. Full article

High light (HL) intensity has a substantial impact on light energy flow and partitioning within photosynthetic apparatus. To realize the impact of HL intensity on zinc (Zn) tolerance mechanisms in clary sage (Salvia sclarea L., Lamiaceae) plants, we examined the effect of the altered chlorophyll and nutrient uptake under excess Zn supply on the response mechanism of photosystem II (PSII) photochemistry. Eight-week-old clary sage plants were treated with 5 μM Zn (control) or 900 μM Zn in Hoagland nutrient solution. Leaf elemental analysis for Zn, Mn, Mg, and Fe was performed by inductively coupled plasma mass spectrometry (ICP-MS), whereas PSII functioning under HL was evaluated by chlorophyll fluorescence imaging analysis. Exposure of S. sclarea plants to 900 μM Zn increased leaf Zn accumulation and decreased leaf Mg and chlorophyll. The decreased non-photochemical quenching (NPQ) provided evidence of the photoprotection offered by the smaller light-harvesting antennae due to the reduced chlorophyll. The increased Mn after Zn exposure corresponded with higher efficiency of the oxygen-evolving complex (OEC) that was significantly correlated with the maximum efficiency of photosystem II (PSII) photochemistry (Fv/Fm). An increased electron transport rate (ETR) coincided with increased leaf Fe, which is known to play a vital role in the enzymes engaged in ETR. The decreased (32%) NPQ after an 8-day exposure to Zn caused an increased (10%) quantum yield of non-regulated energy loss in PSII (Φ_NO), indicative of an increased singlet oxygen (¹O₂) production. It is suggested that the decreased NPQ induced acclimation responses of clary sage plants to HL and excess Zn by increasing ¹O₂ production. The reduced (18%) excess excitation energy (EXC) at PSII and the increased (24%) quantum yield of PSII photochemistry (Φ_PSII) and ETR indicated improved photosynthetic efficiency under excess Zn and HL intensity. Therefore, the exposure of medicinal plants to excess Zn not only boosts their photosynthetic efficiency, enhancing crop yields, but can also improve Fe and Zn content, ameliorating the human health deficiency of these two essential micronutrients. Full article

Magnetism is a ubiquitous property of astrophysical plasmas, yet stellar magnetism still remains far from being completely understood. In this review, we describe recent observational and modelling efforts and progress to expand our knowledge of the magnetic properties of high-mass stars. Several mechanisms (magneto-convection, mass-loss quenching, internal angular momentum transport, and magnetic braking) have significant implications for stellar evolution, populations, and end-products. Consequently, it remains an urgent issue to address and resolve open questions related to magnetism in high-mass stars. Full article

Precise and accurate quantification is a prerequisite for interpretation of targeted metabolomics data, but this task is challenged by the inherent instability of the analytes. The sampling, quenching, extraction, and sample purification conditions required to recover and stabilize metabolites in representative extracts have also been proven highly dependent on species-specific properties. For Escherichia coli, unspecific leakage has been demonstrated for conventional microbial metabolomics sampling protocols. We herein present a fast filtration-based sampling protocol for this widely applied model organism, focusing on pitfalls such as inefficient filtration, selective loss of biomass, matrix contamination, and membrane permeabilization and leakage. We evaluate the effect of and need for removal of extracellular components and demonstrate how residual salts can challenge analytical accuracy of hyphenated mass spectrometric analyses, even when sophisticated correction strategies are applied. Laborious extraction procedures are bypassed by direct extraction in cold acetonitrile:water:methanol (3:5:2, v/v%), ensuring compatibility with sample concentration and thus, any downstream analysis. By applying this protocol, we achieve and demonstrate high precision and low metabolite turnover, and, followingly, minimal perturbation of the inherent metabolic state. This allows us to herein report absolute intracellular concentrations in E. coli and explore its central carbon metabolome at several commonly applied cultivation conditions. Full article

Strawberries are an important fruit in the European diet because of their unique taste and high content of essential nutrients and bioactive compounds. The anthocyanins are known to be colorful phenolics in strawberries. In 17 samples of six strawberry cultivars produced in Serbia, i.e., the common varieties Alba, Asia, and Clery as well as promising breeding materials (11.29.11, 11.34.6, and 11.39.3), the anthocyanin profile as well as antimicrobial and antioxidative activity profiles were determined. All investigated extracts showed antioxidative and antibacterial activities against Gram-negative Aliivibrio fischeri. The responses were quite similar in number and intensity. The HPTLC-DPPH• scavenging assay and HPTLC-Aliivibrio fischeri bioassay coupled with high-resolution mass spectrometry identified pelargonidin-3-O-glucoside (Pg-3-glc) as the main anthocyanin and prominent antioxidative and antimicrobial compound in strawberries. The density functional theory calculations at the M06-2X/6-31+G(d,p) level showed that Pg-3-glc quenches free radicals via sequential proton loss electron transfer mechanism in water and in pentyl ethanoate, where the 5-OH group is the most reactive site for proton and hydrogen atom transfer. The results were confirmed via spectrophotometry. The highest total phenolic content was found in Clery and 11.39.3, while statistically significant differences between the genotypes regarding the antioxidant activity were not confirmed. Although very similar in the anthocyanin, antioxidative, and antimicrobial profile patterns, the strawberry genotypes were successfully classified using principal component analysis. Full article

Concrete is a composite material that is commonly used in the construction industry. It will certainly be exposed to fires of varying intensities when used in buildings and industries. The major goal of this article was to look into the influence of mineral additions such as foundry sand and marble dust on the residual characteristics of concrete. To examine the behavior of residual characteristics of concrete after fire exposure, marble dust was substituted for cement and fine sand was substituted for foundry sand in varying amounts ranging from 0% to 20%. It aided in the better disposal of waste material so that it might be used as an addition. The purpose of the experiment was to see how increased temperatures affected residual properties of concrete, including flexural strength, compressive strength, tensile strength, static as well as dynamic elastic modulus, water absorption, mass loss, and ultrasonic pulse velocity. At temperatures of 200 °C, 400 °C, 600 °C, 800 °C, and 1000 °C, the typical fire exposure behavior of concrete was investigated. The effects of two cooling techniques, annealing and quenching, on the residual properties of concrete after exposure to high temperatures were investigated in this study. Replacement of up to 10% of the cement with marble dust and fine sand with foundry sand when concrete is exposed to temperatures up to 400 °C does not influence the behavior of concrete. At temperatures above 400 °C, however, the breakdown of concrete, which includes marble dust and foundry sand, causes a rapid deterioration in the residual properties of concrete, primarily for replacement of more than 10%. Full article

In this study, the X-ray and gamma attenuation characteristics and optical properties of a synthesized tellurite–phosphate–sodium oxide glass system with a composition of (85 − x)TeO₂–10P₂O₅–xNa₂O mol% (where x = 15, 20, and 25) were evaluated. The glass systems we re fabricated by our research group using quenching melt fabrication. The shielding parameters of as-synthesized systems, such as the mass attenuation coefficient (MAC), linear attenuation coefficient (LAC), effective atomic number (Z_eff), half-value layer (HVL), tenth value layer (TVL), mean free path (MFP), and effective electron density (N_eff) in a wide energy range between 15 keV and 15 MeV, were estimated using well-known PHY-X/PSD software and recently developed MIKE software. Herein, the optical parameters of prepared glasses, such as molar volume (V_M), oxygen molar volume (V_O), oxygen packing density (OPD), molar polarizability (${\mathsf{\alpha }}_{\mathrm{m}}$), molar refractivity (R_m), reflection loss (R_L), and metallization (M), were estimated using MIKE software. Furthermore, the shielding performance of the prepared glasses was compared with that of commonly used standard glass shielding materials. The results show that the incorporation of sodium oxide into the matrix TeO₂/P₂O₅ with an optimum concentration can yield a glass system with good shielding performance as well as good optical and physical properties, especially at low photon energy. Full article

Microstructural and cavitation erosion testing was carried out on Cu-12.8Al-4.1Ni (wt. %) shape memory alloy (SMA) samples produced by continuous casting followed by heat treatment consisting of solution annealing at 885 °C for 60 min and, later, water quenching. Cavitation resistance testing was applied using a standard ultrasonic vibratory cavitation set up with stationary specimen. Surface changes during the cavitation were monitored by metallographic analysis using an optical microscope (OM), atomic force microscope (AFM), and scanning electron microscope (SEM) as well as by weight measurements. The results revealed a martensite microstructure after both casting and quenching. Microhardness value was higher after water quenching than in the as-cast state. After 420 min of cavitation exposure, a negligible mass loss was noticed for both samples. Based on the obtained results, both samples showed excellent cavitation resistance. Mass loss and morphological analysis of the formed pits indicated better cavitation resistance for the as-cast state (L). Full article

This study aims to determine the effect of fast cooling (quenching) on thermal properties, mechanical strength, morphology and size of the AgNWs. The synthesis of AgNWs was carried out at three different quenching-medium temperatures as follows: at 27 °C (ambient temperature), 0 °C (on ice), and −80 °C (in dry ice) using the polyol method at 130 °C. Furthermore, the AgNWs were sonified for 45 min to determine their mechanical strength. Scanning electron microscopy analysis showed that the quenched AgNWs had decreased significantly; at 27 °C, the AgNWs experienced a change in length from (40 ± 10) to (21 ± 6) µm, at 0 °C from (37 ± 8) to (24 ± 8) µm, and at −80 °C from (34 ± 9) to (29 ± 1) µm. The opposite occurred for their diameter with an increased quenching temperature: at 27 °C from (200 ± 10) to (210 ± 10) nm, at 0 °C from (224 ± 4) to (239 ± 8) nm, and at −80 °C from (253 ± 6) to (270 ± 10) nm. The lower the temperature of the quenching medium, the shorter the length and the higher the mechanical strength of AgNWs. The UV-Vis spectra of the AgNWs showed peak absorbances at 350 and 411 to 425 nm. Thermogravimetric analysis showed that AgNWs quenched at −80 °C have better thermal stability as their mass loss was only 2.88%, while at the quenching temperatures of 27 °C and 0 °C the mass loss was of 8.73% and 4.17%, respectively. The resulting AgNWs will then be applied to manufacture transparent conductive electrodes (TCEs) for optoelectronic applications. Full article

A new chemosensor UiO-66-N-Py (Py = 2-methinepyridine, N = imine nitrogen) based on isoreticular UiO-66 (University of Oslo) Metal–Organic Framework (MOF) containing 2-methinepyridine functionalized organic linker was solvothermally synthesized and characterized. This UiO-66-N-Py was very selective and sensitive for detecting the Fe³⁺ ion and sequential detection of the pyrophosphate (PPi) anion. The limits of detection for the Fe³⁺ ion and PPi were calculated to be 10 ppb (0.19 μM) and 50 ppb (0.3 μM), respectively. The quenching constant K_sv for Fe³⁺ and the binding constant for PPi were 1.4 × 10⁵ M⁻¹ and 1.7 × 10⁵ M⁻¹, respectively. The functionalization of UiO-66-NH₂ with 2-methinepyridine enhanced its fluorescence emission properties and introduced more binding sites for the analytes. We additionally studied the interaction of the sensor and the analytes with Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Inductively Coupled Plasma Mass Spectrometry (ICP-MS). This chemosensor also demonstrated a regenerative emission property without loss in the detection ability for six consecutive cycles. Full article

This work investigates the structural, magnetic and magneto-optical properties of a new zinc phosphate-tellurite glass belonging to the 45ZnO-10Al₂O₃-40P₂O₅-5TeO₂ system. The glass was prepared by a wet method of processing the starting reagents followed by suitable melting–stirring–quenching–annealing steps. Specific parameters such as density, average molecular mass, molar volume, oxygen packaging density, refractive index, molar refractivity, electronic polarizability, reflection loss, optical transmission, band gap and optical basicity have been reported together with thermal, magnetic and magneto-optical characteristics. Absorption bands appear in the blue and red visible region, while over 600 nm the glass becomes more transparent. FTIR and Raman spectra evidenced phosphate-tellurite vibration modes proving the P₂O₅ and TeO₂ network forming role. Magnetic measurements reveal the diamagnetic character of the Te-doped glass with an additional weak ferromagnetic signal, specific to diluted ferromagnetic oxides. Positive Faraday rotation angle with monotonous decreasing value at increasing wavelength was evidenced from magneto-optical measurements. The final product is a composite material comprising of a non-crystalline vitreous phase and Te-based nanoclusters accompanied by oxygen vacancies. The metallic-like Te colloids are responsible for the dark reddish color of the glass whereas the accompanying oxygen vacancies might be responsible for the weak ferromagnetic signal persisting up to room temperature. Full article

The current research studied the effects of laser surface hardening treatment on the phase transformation and wear properties of gray cast irons heat treated by austempering or quench-tempering, respectively. Three austempering temperatures of 232 °C, 288 °C, and 343 °C with a constant holding duration of 120 min and three tempering temperatures of 316 °C, 399 °C, and 482 °C with a constant holding duration of 60 min were utilized to prepare austempered and quench-tempered gray cast iron specimens with equivalent macro-hardness values. A ball-on-flat reciprocating wear test configuration was used to investigate the wear resistance of austempered and quench-tempered gray cast iron specimens before and after applying laser surface-hardening treatment. The phase transformation, hardness, mass loss, and worn surfaces were evaluated. There were four zones in the matrix of the laser-hardened austempered gray cast iron. Zone 1 contained ledeburite without the presence of graphite flakes. Zone 2 contained martensite and had a high hardness, which was greater than 67 HRC. Zone 4 was the substrate containing the acicular ferrite and carbon-saturated austenite with a hardness of 41–27 HRC. In Zone 3, the substrate was tempered by the low thermal radiation. For the laser-hardened quench-tempered gray cast iron specimens, three zones were observed beneath the laser-hardened surface. Zone 1 also contained ledeburite, and Zone 2 was full martensite. Zone 3 was the substrate containing the tempered martensite. The tempered martensite became coarse with increasing tempering temperature due to the decomposition of the as-quenched martensite and precipitation of cementite particles. In the wear tests, the gray cast iron specimens without heat treatment had the highest wear loss. The wear performance was improved by applying quench-tempering heat treatment and further enhanced by applying austempering heat treatment. Austempered gray cast iron specimens had lower mass loss than the quench-tempered gray cast iron specimens, which was attributed to the high fracture toughness of acicular ferrite and stable austenite. After utilizing the laser surface hardening treatment, both austempered and quench-tempered gray cast iron specimens had decreased wear loss due to the high surface protection provided by the ledeburitic and martensitic structures with high hardness. In the worn surfaces, it was found that cracks were the dominant wear mechanism. The results of this work have significant value in the future applications of gray cast iron engineering components and provide valuable references for future studies on laser-hardened gray cast iron. Full article

Quercus robur L. is one of the most valued tree species of deciduous temperate forests. However, in the last decade, serious oak declines and loss of adaptation plasticity have been reported throughout Europe as a consequence of drought. Therefore, the aim of the present study was to define the adaptation potential of five Q. robur half-sib lines from the UNESCO Biosphere Reserve Mura-Drava-Danube to drought, using physiological, anatomical and biometrical traits. Half-sib lines that exhibited drought tolerance had particular suites of trait expression regarding biometrical traits (seedling height, root length, root to shoot ratio of dry mass and specific leaf area), leaf stomatal traits (stomatal density per mm², stomata guard cell length and width, stomatal aperture length and width) and leaf structural traits (adaxial epidermis thickness, palisade parenchyma thickness, spongy parenchyma thickness, lamina thickness). All of the observed parameters of chlorophyll a fluorescence were shown to be good indicators of short-term and severe drought. For the selection of drought-tolerant half-sib lines, all studied chlorophyll a fluorescence parameters associated with the heat dissipation of light energy (coefficient of non-photochemical quenching, quantum yield of regulated energy dissipation, Stern-Volmer type non-photochemical fluorescence quenching) and one parameter related to photochemical dissipation of light energy (effective quantum yield (efficiency) of PS II photochemistry) were proven to be suitable. On the other hand, the coefficient of photochemical quenching, coefficient of photochemical fluorescence quenching assuming interconnected photosystem II antennae and electron transport rate were not suitable for distinguishing the different responses of the studied half-sib lines under drought. The importance of results of the present study is in the selection of drought-tolerant Q. robur half-sib lines for future reforestation programs, particularly in protected areas with sensitive forest management and restricted activities for mitigation of the adverse effects of climate changes. Full article