Search Results (1,702)

Background and Objectives: Total hip arthroplasty (THA) following pelvic osteotomy for developmental dysplasia of the hip (DDH) is technically challenging due to altered acetabular morphology. This study aimed to compare radiographic cup position and perioperative characteristics of THA after three common pelvic osteotomies—periacetabular osteotomy (PAO), shelf procedure, and Chiari osteotomy—with primary THA in Crowe type I DDH. Methods: A retrospective review identified 25 hips that underwent conversion THA after pelvic osteotomy (PAO = 12, shelf = 8, Chiari = 5) and 25 primary THAs without prior osteotomy. One-to-one matching was performed based on sex (exact match), age (within 5 years), and BMI (within 2 kg/m²) without the use of propensity scores. Cup inclination, radiographic anteversion, center-edge (CE) angle, and cup height were measured on standardized anteroposterior radiographs (ICC = 0.91). Operative time, estimated blood loss, and use of bulk bone grafts or reinforcement rings were reviewed. One-way ANOVA with Dunnett’s post hoc test and chi-square test were used for statistical comparison. Results: Cup inclination, anteversion, and CE angle did not differ significantly among groups. Cup height was significantly greater in the PAO group than in controls (29.0 mm vs. 21.8 mm; p = 0.0075), indicating a more proximal hip center. The Chiari and shelf groups showed upward trends, though not significant. Mean operative time tended to be longer after PAO (123 min vs. 93 min; p = 0.078). Bulk bone grafts and reinforcement rings were more frequently required in the PAO group (17%; p = 0.036 vs. control), and occasionally in Chiari cases, but not in shelf or control groups. Conclusions: THA after PAO is associated with higher cup placement and greater need for reconstructive devices, indicating increased technical complexity. In contrast, shelf and Chiari conversions more closely resemble primary THA. Preoperative planning should consider hip center translation and bone-stock restoration in post-osteotomy THA. Full article

This paper focuses on the sealing failure problem of double-lip seal rings for high-speed ball bearings used in unmanned aerial vehicles. By using ANSYS 2023R1 software, a thermal–stress–wear coupled finite element model was established. Taking the contact pressure and volume loss due to wear as indicators to evaluate sealing performance, this study analyzed the influence of lip seal structural parameters on sealing performance, performed response surface optimization of the seal structure parameters and conducted a comparative test on lip seals before and after optimization. The research results show that the contact pressure at the main lip of the lip seal was the greatest, which was 0.79 MPa, and the volume loss due to wear lip seal was 7.94 × 10⁻⁷ mm³. Optimal sealing performance is achieved when the seal lip inclination angle is 41.68°, the middle width of the lip seal is 0.153 mm, the main lip height is 0.179 mm, the spring center distance is 0.37 mm and the radial interference is 0.0034 mm. After optimization, the grease leakage rate of the sealing ring decreased by 48% compared to before optimization. Full article

In response to the need for separation and utilization of residual film mixtures after transformation of protaetia brevitarsis larvae, a pneumatic drum-sieve-type separator for transforming mixtures of protaetia brevitarsis larvae was designed. First, the suspension velocity of each component was determined by the suspension speed test. Secondly, the separation process of residual film, larvae, and insect sand was formulated on the basis of biological activities, shape differences, and aerodynamic response characteristics. Eventually, the main structural parameters and working parameters of the machine were determined. In order to optimize the separation effect, a single-factor experiment and a quadratic regression response surface experiment containing three factors and three levels were carried out, and the corresponding regression model was established. The experimental results showed that the effects of the air speed at the inlet, inclination angle of the sieve cylinder, and rotational speed of the sieve cylinder on the impurity rate of the residual film decreased in that order, and that the effects of the rotational speed of the sieve cylinder, inclination angle of the sieve cylinder, and air speed at the inlet on the inactivation rate of the larvae decreased in that order. Through parameter optimization, a better combination of working parameters was obtained: the rotational speed of the sieve cylinder was 24 r/min, the inclination angle of the sieve cylinder was −0.43°, and the air speed at the inlet was 5.32 m/s. The average values of residual film impurity rate and larval inactivation rate obtained from the material sieving test under these parameters were 8.74% and 3.18%, with the relative errors of the theoretically optimized values being less than 5%. The results of the study can provide a reference for the resource utilization of residual film and impurity mixtures and the development of equipment for the living body separation of protaetia brevitarsis. Full article

A two-phase closed thermosyphon (TPCT), a gravity-assisted heat pipe, is a highly efficient heat transmitter involving liquid–vapor phase change. It is used in many applications, including heat spreading, thermal management and control, and energy saving. The main objective of this study is to investigate the effects of the operating conditions for a thermosyphon used in solar water heaters. The study particularly focuses on the influence of the inclination angle. Thus, a comprehensive simulation model is developed using the volume of fluid (VOF) approach. Complex and related phenomena, including two-phase flow, phase change, and heat exchange, are taken into account. To implement the model, an open-source CFD toolbox based on finite volume formulation, OpenFOAM, is used. The model is then validated by comparing numerical results to the experimental data from the literature. The obtained results show that the simulation model is reliable for investigating the effects of various operating conditions on the transient and steady-state behavior of the thermosyphon. In fact, bubble creation, growth, and advection can be tracked correctly in the liquid pool at the evaporator. The effects of the designed operating conditions on the heat transfer parameters are also discussed. In particular, the optimal tilt angle is shown to be 60° for the intermediate saturation temperature (<50 °C) and 90° for the larger saturation temperature (>60 °C). Full article

Cranial cruciate ligament (CrCL) rupture is a common orthopedic disorder in dogs, leading to stifle joint instability and progressive osteoarthritis. This study aimed to develop and biomechanically evaluate a novel intra-articular reconstruction system designed to mimic the natural ligament and restore joint stability following CrCL excision. The system consisted of a 3D-printed thermoplastic polyurethane (TPU) graft, cerclage wire, and H-button fixation. Fourteen pelvic limbs from mature mixed-breed cadaveric dogs were used. The inclination angle, dimensions, volume, tensile strength, and elongation of the native CrCL were measured. Seven CrCL-deficient stifles were reconstructed using the proposed system and tested biomechanically. The native CrCL showed a significantly higher tensile strength than the TPU graft; however, the TPU demonstrated a greater flexibility. The reconstruction system successfully stabilized the joint and provided repeatable fixation. Significant correlations were found between CrCL volume and both age and body weight. These findings support the mechanical suitability of the proposed system for ex vivo stifle stabilization and highlight the potential of 3D-printed TPU in ligament reconstruction. Further in vivo studies are recommended to assess long-term performance, including implant integration, tissue remodeling, and clinical outcomes. Full article

Water systems are highly vulnerable to biofilm formation, which can compromise water quality, operational efficiency, and public health. Factors such as surface material properties and gravitational orientation of the surface play critical roles in the early stages of microbial attachment and biofilm development. This study examines the impact of gravity and surface composition on the initial adhesion of Pseudomonas fluorescens AR11—a model organism for biofilm research. Focusing on stainless steel (SS) and polycarbonate (PC), two materials commonly used in water and wastewater infrastructure, bacterial adhesion was evaluated at surface inclinations of 0°, 45°, 90°, and 180° to assess gravitational impact. After three hours of contact, fluorescence microscopy and image analysis were used to quantify surface coverage and cluster size distribution. The results showed that both material type and orientation significantly affected early biofilm formation. PC surfaces consistently exhibited higher bacterial adhesion at all angles, with modest variations, suggesting that material properties are a dominant factor in initial colonization. In contrast, SS showed angle-dependent variation, indicating a combined effect of gravitational convection and surface characteristics. These insights contribute to a deeper understanding of biofilm dynamics under realistic environmental conditions, including those encountered in space systems, and support the development of targeted strategies for biofilm control in water systems and spaceflight-related infrastructure. Full article

In this study, the tool axis inclination angle with respect to the surface normal is used to compare the wear of spherical and toroidal milling cutters. Five different surface types were machined in this investigation using three toroidal and three spherical milling cutters at inclination angles of 15°, 35°, and 55°. Each cutter processed 45 surfaces, nine of each type. The MM1-200 microscope was used to monitor tool wear under a microscope after the surfaces had been machined. A comparison diagram and microscopic pictures of tool wear in relation to the wear surface are presented in the paper. Additionally, it contrasts the tool edge’s state at the conclusion of machining with its state following five years of storage, during which time the tool was subjected to environmental influences. Full article

The shear tests are conducted on six precast segmental concrete beams (PSCBs) in this paper. A new specimen design scheme is presented to compare the effects of segmental joints on the shear performance of PSCBs. The failure modes, shear strength, structural deflection, stirrup strain, and tendon stress are recorded. The factors of shear span ratio, the position of segmental joints, and hybrid tendon ratio are focused on, and their effects on the shear behaviors are compared. Based on the measured responses, the shear contribution proportions of concrete segments, prestressed tendons, and stirrups are decomposed and quantified. With the observed failure modes, the truss–arch model is employed to clarify the shear mechanism of PSCBs, and simplified equations are further developed for predicting the shear strength. Using the collected test results of 30 specimens, the validity of the proposed equations is verified with a mean ratio of calculated-to-test values of 0.96 and a standard deviation of 0.11. Furthermore, the influence mechanism of shear span ratio, segmental joints, prestressing force, and hybrid tendon ratio on the shear strength is clarified. The increasing shear span ratio decreases the inclined angle of the arch ribs, thereby reducing the shear resistance contribution of the arch action. The open joints reduce the number of stirrups passing through the diagonal cracks, lowering the shear contribution of the truss action. The prestressing force can reduce the inclination of diagonal cracks, improving the contribution of truss action. The external unbonded tendon will decrease the height of the arch rib due to the second-order effects, causing lower shear strength than PSCBs with internal tendons. Full article

Object detection in aerial images can provide great support in traffic planning, national defense reconnaissance, hydrographic surveys, infrastructure construction, and other fields. Objects in aerial images are characterized by small pixel–area ratios, dense arrangements between objects, and arbitrary inclination angles. In response to these characteristics and problems, we improved the feature extraction network Inception-ResNet using the Fast Architecture Search (FAS) module and proposed a one-stage anchor-free rotation object detector. The structure of the object detector is simple and only consists of convolution layers, which reduces the number of model parameters. At the same time, the label sampling strategy in the training process is optimized to resolve the problem of insufficient sampling. Finally, a decoupled object detection head is used to separate the bounding box regression task from the object classification task. The experimental results show that the proposed method achieves mean average precision (mAP) of 82.6%, 79.5%, and 89.1% on the DOTA1.0, DOTA1.5, and HRSC2016 datasets, respectively, and the detection speed reaches 24.4 FPS, which can meet the needs of real-time detection. Full article

This study investigates the influence of inclination on a submerged plate (SP) device acting as both a breakwater (BW) and a wave energy converter (WEC) subjected to representative regular and realistic irregular waves of a sea state across 11 inclination angles. Numerical simulations were conducted using ANSYS Fluent. Regular waves were generated by Stokes’s second-order theory, while the WaveMIMO technique was employed to generate irregular waves. Using the volume of fluid (VOF) method to model the water–air interaction, both approaches generate waves by imposing their vertical and horizontal velocity components at the inlet of the wave flume. The SP’s performance as a BW was analyzed based on the upstream and downstream free surface elevations of the device; in turn, its performance as a WEC was determined through its axial velocity beneath the plate. The results indicate that performance varies between regular and irregular wave conditions, underscoring the importance of accurately characterizing the sea state at the intended installation site. These findings demonstrate that the inclination of the SP plays a critical role in balancing its dual functionality, with certain configurations enhancing WEC efficiency by over 50% while still offering relevant BW performance, even under realistic irregular sea conditions. Full article

Falls are a major safety concern in physically demanding occupations such as roofing, where workers operate on inclined surfaces under unstable postures. While inertial measurement units (IMUs) are widely used in wearable fall detection systems, they often fail to capture early indicators of instability related to foot–ground interactions. This study evaluates the effectiveness of plantar pressure sensors, alone and combined with IMUs, for fall detection on sloped surfaces. We collected data in a controlled laboratory environment using a custom-built roof mockup with incline angles of 0°, 15°, and 30°. Participants performed roofing-relevant activities, including standing, walking, stooping, kneeling, and simulated fall events. Statistical features were extracted from synchronized IMU and plantar pressure data, and multiple machine learning models were trained and evaluated, including traditional classifiers and deep learning architectures, such as MLP and CNN. Our results show that integrating plantar pressure sensors significantly improves fall detection. A CNN using just three IMUs and two plantar pressure sensors achieved the highest F1 score of 0.88, outperforming the full 17-sensor IMU setup. These findings support the use of multimodal sensor fusion for developing efficient and accurate wearable systems for fall detection and physical health monitoring. Full article

A novel prefabricated pile foundation is presented to improve the disaster resistance of the pole line. Bearing performance analysis of prefabricated inclined pile foundations for electric poles under downward pressure-horizontal loading is carried out, and the effects of prefabricated foundation dimensions and pile inclination on the horizontal load–displacement curves at the top of the poles, the horizontal displacement and settlement at the top of the piles, the horizontal displacement and tilt rate of the poles’ bodies and piles bending moments are investigated. The findings indicate the following: as the prefabricated foundation size grows, the bearing capacity of the foundation improves, and the anti-overturning ability of the electric pole improves; the foundation size increases from 0.9 m to 1.35 m, the anti-overturning bearing capacity of the foundation increases by 15.77%, the maximum bending moment of the foundation pile body increases by 19.7%, and the maximum bending moment occurs at about 0.2 m of the pile body; the bearing capacity of inclined piles is larger than that of straight piles—with an increase in the pile inclination angle, the foundation bearing performance increases, and the overturning bearing capacity of the poles increases; the pile inclination angle grows from 0° to 20°, the overturning bearing performance of the foundation increases by 19.2%, the maximum bending moment of the foundation piles reduces by 21.2%, and the maximum of the bending moment occurs at the pile body at a position of about 0.2 m. Full article

To enhance the fire safety protection level of deeply buried metro stations, this study conducted full-scale fire experiments based on Wulichong Station of Guiyang Metro Line 3. It systematically investigated the laws of smoke movement and temperature distribution under the coupled effects of different fire source powers and smoke extraction system states. Through the set up of multiple sets of comparative test conditions, the study focused on analyzing the influence mechanism of the operation (on/off) of the smoke extraction system on smoke spread characteristics and temperature field distribution. The results indicate that under the condition where the smoke extraction system is turned off, the smoke exhibits typical stratified spread characteristics driven by thermal buoyancy, with the temperature rising significantly as the vertical height increases. When the smoke extraction system is activated, the horizontal airflow generated by mechanical smoke extraction significantly alters the flame morphology (with an inclination angle exceeding 45°), effectively extracting and discharging the hot smoke and leading to a more uniform temperature distribution within the space. Full article

A jet flow mixer is a novel agitator type widely used in the industry. However, scientific research has yet to be conducted on this impeller type. In this study, six types of fluids with various properties widely used in the paint industry were chosen to calculate the positioning of the jet flow mixer in the tank. Calculations were performed using computational fluid dynamics (CFD) software and validated using literature data. Simulations were conducted to consider the inside of the jet flow mixer and the inside of the tank. The initial calculations made for jet flow mixers allowed the determination of volume flow and power numbers for three types of mixers (propeller agitator and Pitched Blade Turbine with three and four blades). Those parameters were then used in subsequent calculations, obtaining the optimal inclination angle of the agitator and power consumption for each considered case. The jet flow mixer with a propeller impeller positioned at an angle of 45° proved to be the choice to achieve the best results. Full article

In wind-assisted orchard spraying operations, the dynamic response of leaves—manifested through changes in their posture—critically influences droplet deposition on both sides of the leaf surface and the penetration depth into the canopy. These factors are pivotal in determining spray coverage and the spatial distribution of pesticide efficacy. However, current research lacks comprehensive quantification and correlation analysis of the temporal response characteristics of leaves under wind disturbances. To address this gap, a systematic analytical framework was proposed, integrating real-time leaf segmentation and tracking, geometric feature quantification, and statistical correlation modeling. High-frame-rate videos of fluttering leaves were acquired under controlled wind conditions, and background segmentation was performed using principal component analysis (PCA) followed by clustering in the reduced feature space. A fine-tuned Segment Anything Model 2 (SAM2-FT) was employed to extract dynamic leaf masks and enable frame-by-frame tracking. Based on the extracted masks, time series of leaf area and inclination angle were constructed. Subsequently, regression analysis, cross-correlation functions, and Granger causality tests were applied to investigate cooperative responses and potential driving relationships among leaves. Results showed that the SAM2-FT model significantly outperformed the YOLO series in segmentation accuracy, achieving a precision of 98.7% and recall of 97.48%. Leaf area exhibited strong linear coupling and directional causality, while angular responses showed weaker correlations but demonstrated localized synchronization. This study offers a methodological foundation for quantifying temporal dynamics in wind–leaf systems and provides theoretical insights for the adaptive control and optimization of intelligent spraying strategies. Full article