Search Results (96)

Femtosecond laser surface texturing offers a promising route to tailor the functionality of bio-based wood coatings, yet the interplay between coating composition and laser processing remains poorly understood. In this study, bio-based epoxy coatings with eventual micronized wax additives were textured using a femtosecond laser to investigate the effects of laser processing parameters on pattern formation and resulting hydrophobicity. The epoxy coatings containing PE, PE/PTFE, HDPE, and rice bran waxes at 1, 5, and 7 wt.-% were characterized in terms of morphology, roughness, wettability, and chemical stability, followed by systematic variation of pulse repetition rate and laser power. The results reveal that the ablation threshold strongly depends on intrinsic coating properties. Ablation resistance increases with surface roughness and wax melting enthalpy, reflecting the role of phase transition energy in laser–matter interaction. The wax-filled coatings exhibit a transition from melting-dominated behavior at low energy input to ablation-dominated behavior at a higher energy. Laser texturing enhances hydrophobicity in parallel with theoretical values calculated from the Cassie–Baxter wetting model, with the highest hydrophobicity achieved for coatings combining intrinsic hydrophobicity and stable pattern formation. Chemical analysis confirms limited degradation of the epoxy matrix without significant carbonization, while wax additives provide partial thermal shielding. Overall, this work demonstrates clear options for tailoring surface morphology and wettability of hydrophobic polymer coatings through controlled femtosecond laser processing. Full article

Ultra-High Molecular Weight Polyethylene (UHMWPE), the standard base material in ski manufacturing, offers excellent gliding performance but exhibits limited mechanical and scratch resistance on hard and icy snow conditions. In this work, stainless steel is proposed as a mechanically robust alternative, and its inherently higher friction against snow is addressed through surface engineering. The snow friction behavior of 301H stainless steel surfaces decorated with fishbone-like microstructures combined with Laser-Induced Periodic Surface Structures (LIPSSs) was investigated using a custom-built snow tribometer. Several pattern designs, with different pitch distances and depths, were engraved using femtosecond laser pulse irradiation. We conducted morphological, physical, and chemical investigations through microscopy, static contact angle measurements, and X-ray Photoelectron Spectroscopy analyses. Results indicate that the gliding performance is not directly related to the modifications in surface chemistry and wetting behavior of the samples but is affected by the geometry and orientation with respect to the sliding direction of the specific micro- and nano-features. Overall, we achieved friction coefficient values comparable to those found in UHMWPE with a fast and economically sustainable single-step laser-texturing process. This approach allows the industrial up-scaling of the fishbone-texture design to real-size alpine ski prototypes. Full article

Surface protection and functional modification of aircraft-certified aluminum alloys are essential for corrosion resistance, durability, and long-term airworthiness. At the same time, increasingly restrictive environmental regulations motivate the development of alternatives to legacy wet-chemical surface treatments. This study presents an integrated assessment of ultrafast femtosecond laser surface texturing as a surface functionalization approach for Aluminum 6061 alloys within an aerospace manufacturing and sustainability context. Ultrashort-pulse laser processing enables controlled micro- and nano-scale surface topographical modification with limited thermal impact, allowing adjustment of wettability and surface functionality while preserving bulk material integrity. As a dry and contactless process, femtosecond laser treatment eliminates the use of hazardous chemicals, reduces consumable inputs, and generates minimal secondary waste. A streamlined cradle-to-gate life cycle assessment conducted in accordance with ISO 14040/14044 indicates a lower global-warming potential per functional unit compared with conventional surface treatments, including anodization, plasma-assisted coatings, and organic coating systems. Complementary qualitative analyses addressing environmental health and safety, supply-chain risk, and ESG alignment indicate potential advantages related to occupational safety, regulatory compliance, waste management, and end-of-life recyclability. The investigation is performed on planar Aluminum 6061 reference surfaces with a treated area of 25 mm², providing a controlled laboratory-scale basis for analyzing process behavior, functional surface modification, and associated environmental metrics. Within this defined scope, the results support further evaluation of femtosecond laser surface texturing as a surface engineering option for future aerospace manufacturing. Full article

To improve the tribological performance of 40Cr steel, a biomimetic composite micro-texture consisting of sinusoidal grooves and circular dimples was designed based on the periodic corrugated structures on the shell surface of Fimbria fimbriata. The texture parameter ranges were determined through microscopic characterization of the shell surface and orthogonal design. The composite micro-textures were fabricated on 40Cr steel by femtosecond laser processing and characterized by confocal microscopy, white light interferometry (WLI), and scanning electron microscopy (SEM). Their tribological behavior was evaluated under oil-lubricated reciprocating sliding conditions against a GCr15 counter-body in a ball-on-flat contact configuration. The results showed that laser power significantly affected the forming quality of the sinusoidal textures, and 4.50 W provided the best overall cross-sectional morphology. All textured specimens exhibited lower steady-state average coefficients of friction (COF) than the untextured specimen, with the textured groups ranging from 0.1678 to 0.1905. Among them, specimen L6 showed the lowest steady-state average COF of 0.1678, corresponding to a reduction of approximately 19.4%, together with the best wear resistance as indicated by the relative displacement volume ratio (K_w). Surface analyses revealed that abrasive wear and adhesive wear were the dominant wear mechanisms, while the optimized composite micro-texture effectively suppressed wear-groove development, material pile-up, and transfer-layer formation. Overall, the biomimetic sinusoidal-circular composite micro-texture effectively improved the tribological performance of 40Cr steel under oil lubrication through the synergistic effects of contact-state regulation, lubricant retention, and wear-debris capture. This study provides theoretical and experimental support for the engineering application of biomimetic composite micro-textures on mechanical surfaces. Full article

This study investigates the femtosecond laser surface texturing approach to tune the wetting properties of glass substrates applied for photovoltaic panels. Two types of microstructured LIPSS-containing motifs—parallel channels and intersecting (crossing) patterns—were fabricated and evaluated through comprehensive durability tests, including thermal cycling, UV exposure, chemical immersion, mechanical abrasion, and dust retention assessment. Wettability measurements showed that both textures exhibit stable hydrophilicity behavior, with the intersecting patterns exhibiting the fastest wetting dynamics; in many cases, complete surface wetting occurred within the first few minutes, preventing a measurable contact angle at later stages. The durability tests caused only minor smoothing of the textured features, and the overall micro- and nanostructures remained intact. Optical characterization revealed that the laser-induced textures maintained high transmittance with no significant degradation after environmental exposure. Overall, the results demonstrate that femtosecond laser texturing provides a robust, coating-free method for producing stable and tunable wetting behavior on glass, offering a promising pathway for the future creation of durable, highly hydrophilic self-cleaning surfaces in photovoltaic systems. Full article

Engineering surfaces operating in harsh environments frequently require simultaneous resistance to abrasive wear and the minimization of interfacial adhesion. Achieving this dual functionality through a single surface modification strategy remains challenging. This study presents a novel hybrid approach combining bionic laser surface texturing with a polytetrafluoroethylene/polydimethylsiloxane/TiO₂ nanocomposite coating to synergistically enhance both wear resistance and hydrophobicity of 65Mn steel. Crescent-shaped micro-dimples, inspired by the exoskeleton of Procambarus clarkii, were fabricated via a femtosecond laser. A composite coating containing hydrophobically modified TiO₂ nanoparticles was subsequently deposited. Single-factor experiments identified effective parameter ranges. A four-factor, five-level central composite rotatable design combined with response surface methodology was employed to systematically optimize texture depth, texture spacing, TiO₂ mass fraction, and coating thickness. The results demonstrate that textures with a depth of less than 100 μm and spacing less than 400 μm effectively homogenize surface stress distribution. RSM analysis revealed that TiO₂ content and texture depth predominantly influence hydrophobicity, while texture spacing overwhelmingly controls wear mass loss. Significant interactions between coating and texture parameters were identified. The optimal parameter combination was determined as: 6% TiO₂, 40 μm coating thickness, 50 μm texture depth, and 250 μm texture spacing. Under these conditions, the surface achieved a superhydrophobic contact angle of 152.1° and a low-wear mass loss of 8.9 mg. Validation tests yielded values of 150.8° and 9.3 mg, respectively, confirming model reliability. The synergistic mechanism involves textures acting as debris reservoirs and stress distributors, while the coating provides a low-surface-energy, hardened top layer that minimizes adhesion and facilitates a rolling–sliding contact mode. This work provides a robust, optimized framework for designing multifunctional surfaces for demanding tribological applications. Full article

Laser surface texturing (LST) structures or laser-induced periodic surface structures (LIPSS) are typically created using laser pulses with durations ranging from femtoseconds to nanoseconds. However, nanosecond pulsed lasers, as cost-effective and more productive alternatives, can also be used to generate LST structures on stainless steel (SS) surfaces, making these structures more suitable for industrial applications. In this study, pulsed laser processing is employed to create LST structures on SS (AISI 304), with varying pulse and accumulated fluences, effective pulse counts, and scan parameters, such as pulse-to-pulse distance (pitch) and hatch spacing between scanning lines. A methodology for calculating oxidation density on processed AISI 304 surfaces is presented. Oxidation density, defined as the ratio of the oxidized area to the total processed area, is determined as a function of accumulated fluence, laser power, pulse-to-pulse distance, and hatch spacing. Optical images of the surfaces are analyzed, and oxidation regions are identified using machine learning techniques. The images are converted to grayscale, and machine learning algorithms are applied to classify the images into oxidation and non-oxidation regions based on pixel intensity values. This approach identifies the optimal threshold for separating the two regions by maximizing inter-class variance. Experimental modeling using response surface methodology is applied to experimentally generated data. Optimization algorithms are then employed to determine the process parameters that maximize pulsed laser irradiation performance while minimizing surface oxidation and processing time. This paper also presents a novel method for characterizing oxidation density using image segmentation and machine learning. The results provide a comprehensive understanding of the process and offer optimized models, contributing valuable insights for practical applications. Full article

This work systematically investigates the coupled effects of femtosecond laser parameters (wavelength: 515 nm, pulse width: 373 fs, laser fluence: 3.18–12.7 J/cm², repetition frequence: 100 kHz) and post-fabrication thermal treatment on the micro/nano-structure evolution and wettability of aluminum alloys. By varying the scanning spacing (20–80 μm) and laser fluence, diverse hierarchical surface morphologies were obtained. At a small scanning spacing of 20 μm, increasing laser fluence causes severe thermal accumulation and structural collapse, with the microstructure height decreasing from 42.68 μm to 20.30 μm and the water contact angle (WCA) dropping from 158.6° to 143.5°, indicating a degradation of the superhydrophobic state. In contrast, at larger spacings (60–80 μm), moderate fluence enhances microstructure depth and roughness, yielding peak WCAs of ~160°, while excessive fluence induces feature coarsening and partial loss of nanoscale textures, leading to reduced wettability. Nanoscale evolution shows that optimized laser conditions promote dense nanoparticle redeposition and stable ridge-like structures. These structures are accompanied by cotton-like features with pore diameters of 50–100 nm and coral-like porous features with pore diameters of 100–200 nm, whereas excessive laser etching damage these nano-structures. Among, a scanning spacing of 40 μm achieves this most robust hierarchical nano-structure, corresponding to a maximum WCA of 162.6°. These results clarify the role of femtosecond laser parameters in regulating micro/nano-structural formation and the subsequent modulation of wettability through thermal treatment, providing a reference for the fabrication of coating-free superhydrophobic aluminum alloy surfaces. Full article

In this work, we demonstrate precise control over laser-induced periodic surface structures (LIPSS) on stainless steel (SS) using femtosecond (fs) laser processing to suppress bacterial adhesion. We systematically compare the antifouling behavior of laser-textured surfaces with distinct pattern directionalities—linear and circular. Fs laser irradiation with linear polarization produces directional and anisotropic LIPSS, which progressively evolve into more complex hierarchical surface textures as processing conditions vary. In contrast, fs laser irradiation with circular polarization yields isotropic surface morphologies. Despite these morphological differences, the surface wettability remains nearly constant, with contact angles confined to a narrow range of 32.6–36.9°. Bacterial adhesion tests using Escherichia coli reveal that surfaces patterned with anisotropic features generated by linear polarization—particularly at an incident power of 30 mW—exhibit enhanced antifouling performance compared to isotropic counterparts. These results indicate that antifouling efficacy is governed not only by surface wettability but also by the spatial organization and anisotropy of the LIPSS. This study highlights the critical role of polarization-controlled fs laser processing in tailoring surface architectures and provides a rational strategy for designing bio-resistant metallic surfaces. Full article

The operational ability of a unit or mechanism depends mainly on the quality of the mechanically produced working surfaces. Many materials can be assigned to a group of hard-to-cut materials that includes titanium- and aluminum-based alloys, a new class of heat-resistant alloys, SiCp/Al composites, hard alloys, and other alloys. The difficulties in their machining are related not only to the high temperatures achieved on the contact pads under mechanical load and the extreme cutting conditions but also to the properties of those materials, which affect the adhesion of the chip to the tool faces, hindering chip flow. One of the possible solutions to reduce those effects and improve the operational life of the tool, and as a consequence, the final quality of the working surface of the unit, is texturing the rake face of the tool with microgrooves or nanogrooves, microholes or nanoholes (pits, dimples), micronodes, cross-chevron textures, and other microtextures, the depth of which is in the range of 3.0–200.0 µm. This review is addressed at systematizing the data obtained on micro- and nanotexturing of PCD tools for cutting hard-to-cut materials by different techniques (fiber laser graving, femto- and nanosecond laser, electrical discharge machining, fused ion beam), additionally subjected to fluorination and dip- and drop-based coatings, and the effect created by the use of the textured PCD tool on the machined surface. Full article

We explore the wettability modulation induced on alumina (Al₂O₃) targets by femtosecond laser texturing to demonstrate the stable and durable hydrophilic character of the surface. Specifically, we identify a suitable operational regime to tailor micro-nanostructures onto Al₂O₃ plates and accurately assess the ablation threshold in our experimental conditions. A periodic geometry with triangular patterns of various groove depths, ranging from 3.2 ± 0.1 to 17.1 ± 0.1 µm, was optimized for establishing a long-term wetting response. The latter was monitored on daily basis over a time interval exceeding 40 days by collecting the contact angle measurements of samples with and without a post-process thermal annealing, adopted to stabilize the surface wettability soon after the laser treatment. The results show that deeper grooves significantly enhance and maintain the hydrophilic character, particularly in samples without post-process thermal annealing, where superhydrophilicity (θ < 5°) is demonstrated to persist the entire time throughout the test. These findings disclose the potential for an effective fine-tuning of the alumina wettability, thus opening up the possibility of specific applications requiring long-term control of surface–liquid interactions, such as biomedical implants, and orthopedic and dental prostheses. Full article

Poly(ether ether ketone)/carbon-fiber (PEEK/CF) composites possess excellent mechanical and thermal stability but exhibit inadequate friction and wear resistance for demanding tribological applications. In this study, femtosecond laser texturing was used to generate sinusoidal–circular hybrid microtextures on PEEK/CF surfaces, and the effects of laser power and geometric parameters were systematically evaluated through a Taguchi L9 design. The optimal laser power of 0.85 W produced the highest machining quality factor (MQF = 0.968). The textures caused a hydrophilic-to-hydrophobic transition, increasing the static contact angle from 43° to 96.2°. Under boundary lubrication, all textured specimens exhibited reduced steady-state friction compared with the untreated surface. Among them, specimen L7—corresponding to the largest amplitude (A) and wavelength (B) levels in the orthogonal design—achieved the lowest average coefficient of friction (≈0.12) and generated the narrowest wear track. These results demonstrate that femtosecond-laser-fabricated hybrid microtextures effectively enhance lubricant retention and improve the tribological performance of PEEK/CF composites. Full article

The wheel–rail friction coefficient is a critical factor influencing train traction and braking performance. Low-adhesion conditions not only limit the enhancement of railway transport capacity but are also the primary cause of surface damage such as scratches, delamination, and flat spots. This study employs femtosecond laser technology to fabricate wavy groove textures on U75V rail surfaces, systematically investigating the effects of the wavy angle and texture area ratio on friction enhancement under various medium conditions. Findings indicate that parameter-optimized textured surfaces not only significantly increase the coefficient of friction but also exhibit superior wear resistance, vibration damping, and noise reduction properties. The optimally designed wavy textured surface achieves significant friction enhancement under water conditions. Among the tested configurations, the surface with parameters θ = 150°@η = 30% demonstrated the most pronounced friction enhancement, achieving a coefficient of friction as high as 0.57—a 42.5% increase compared to the non-textured surface (NTS). This enhancement is attributed to the unique hydrophilic and anisotropic characteristics of the textured surface, where droplets tend to spread perpendicular to the sliding direction, thereby hindering the formation of a continuous lubricating film as a third body. Analysis of friction vibration signals reveals that textured surfaces exhibit lower vibration signal amplitudes and richer frequency components. Furthermore, comparison of Stribeck curves under different lubrication regimes for the θ = 150°@η = 30% specimen and NTS indicated an overall upward shift in the curve for the textured sample. The amplitude, energy, and wear extent of the textured surface consistently decreased across boundary lubrication, hydrodynamic lubrication, and mixed lubrication regimes. These findings provide crucial theoretical insights and technical guidance for addressing low-adhesion issues at the wheel–rail interface, offering significant potential to enhance wheel–rail adhesion characteristics in engineering applications. Full article

The increasing prevalence of orthopedic disorders and technological advances have significantly improved the design and functionality of orthopedic implants, fostering the growth of the orthopedic implant market. Polyetheretherketone (PEEK) has emerged as a promising alternative to the gold standard of metallic implants due to its favorable biocompatibility and mechanical properties, comparable to those of bone tissue. However, its chemical inertness results in poor osseointegration. This study investigates femtosecond (fs) laser-induced micro- and nanoscale surface modifications of PEEK, aiming to develop surface modifications potentially favorable for bioactivity enhancement of the as-created transient cellular scaffolds. Various texturing designs were fabricated by precisely controlling the laser parameters applied (laser beam power P = 20–80 mW, hatch spacing dx = 45–100 µm, scanning velocity V = 3.44–32 mm/s). The resulting morphologies were characterized by SEM, EDX, XRD, micro-Raman, 3D profilometry, water contact angle measurements, and evaluated for preliminary biological response. The main achievement of the research indicates that the hierarchical topography created by fs laser microprocessing significantly increased surface morphology, which may subsequently provide surface conditions supporting successful osseointegration. These findings demonstrate the feasibility of femtosecond laser structuring as a promising, reproducible, and environmentally friendly method for sustainable surface biofunctionalization of PEEK in orthopedic applications. Full article

Today, the engineering of load-bearing bone tissue after severe trauma still relies on metal-based (Ti, CoCrMo alloys or stainless steel) permanent implants. Such artificial scaffolds are typically applied in the body and come into direct contact with the recipient’s cells, whose adhesion affects the patient’s implant acceptance or rejection. The present study aims to create a nano-rough texture by means of ultra-short femtosecond laser (fs)-induced periodicity in the form of laser induced periodic surface structures (LIPSS) on the surface of a stainless steel implant model, which is additionally functionalized via magnetron-sputtering with a thin Cu layer, thus providing the as-created implants with a stable antimicrobial interface. Calcium phosphate (CaP) crystal growth was additionally applied due to the strong bioactive interface bond that CaPs provide to the bone connective tissue, as well as for the strong interface bond they create between the artificial implant and the surrounding bone tissue, thereby stabilizing the implanted structure within the body. The bioactive properties in the as-created antimicrobial hybrid topographical design, achieved through femtosecond laser-induced nanoscale surface structuring and micro-sized CaP crystal growth, have the potential for subsequent practical applications in bone tissue engineering. Full article