Search Results (623)

The co-gasification of bio-oil produced via fast pyrolysis and black liquor from the pulp industry may yield a valuable feedstock for renewable gasification. This study investigated the synergistic potential of this co-gasification process. Experiments were conducted in a miniature conical spouted-bed reactor at 800 °C using bio-oil/black liquor mixing ratios ranging from 1:9 to 9:1 under equivalence ratios (ER) of 0.1, 0.3, and 0.5. Syngas characteristics and gasification performance were assessed using the lower heating value (LHV), H₂/CO ratio, cold gas efficiency (CGE), and carbon conversion ratio (CCR). Increasing the bio-oil fraction increased CO and CH₄ concentrations due to its higher carbon content and lower moisture content, whereas black liquor promoted H₂ formation through moisture-driven water–gas shift reactions. Higher ER values intensified combustion, increasing CO₂ while reducing combustible gases. The most energy-rich syngas, with the highest LHV and CGE, was obtained using a 9:1 mixture at ER = 0.1. The CCR was greatest for pure bio-oil and the 5:5 ratio among mixtures, reflecting the catalytic effects of alkali species in black liquor. These results demonstrate that co-gasification can improve syngas quality and carbon utilization, with optimal performance depending on the intended application. Full article

Feedstock quality has been proven to be the single variable that most affects fluid catalytic cracking (FCC) unit performance, but catalyst characteristics have also been reported in the literature to have a considerable effect on cracking process performance. How these two main variables of the FCC process complement each other in the search for ways to optimize the performance of the FCC unit is the subject of current research. Twenty-one feedstocks with K_W-characterizing factors ranging from 11.08 to 12.06, Conradson carbon contents ranging from 0.05 to 12.8 wt.%, and nitrogen contents ranging from 800 to 3590 ppm (wt/wt) (basic nitrogen from 172 to 1125 ppm (wt/wt)) were cracked on 21 catalysts with micro-activity between 67% and 76% (wt/wt) in a laboratory-based advanced catalytic evaluation (ACE) unit at a reaction temperature of 527 °C, catalyst–to-oil ratios between 3.5 and 12.0 wt/wt, and a catalyst time on stream of 30 s. Some of the feeds and catalysts tested in the laboratory FCC ACE unit were also examined in a commercial short-contact-time FCC unit resembling a UOP side-by-side design. It was found that conversion can be very well predicted in both the laboratory ACE and the commercial FCC units using multiple linear correlations developed in this work from information about the following feed properties: K_W-characterizing factor, nitrogen content, and micro-activity of the catalyst. The coke on the catalyst that controls the catalyst-to-oil ratio and the regenerator temperature in the commercial FCC unit could be calculated using the correlations developed in this work for the laboratory ACE and commercial FCC units, based on feed characteristics and catalyst micro-activity. Due to the greater slope of the Δ coke/Δ micro-activity dependence observed in the ACE FCC unit, the more active catalysts show weaker results compared to the less active catalysts at a constant coke yield. In contrast, catalysts with higher activity are preferable for operation in the commercial FCC plant because they provide higher conversion at the same coke yield due to the lower slope of the Δ coke/Δ micro-activity relationship. Full article

Hydrothermal liquefaction (HTL) is a thermochemical process by which biomass feedstocks are converted into bio-oil and multiple by-products, including aqueous co-product (ACP), gaseous co-product (GCP), and biochar. Bio-oil produced from food waste feedstocks represents a potential candidate for use in commercial waste-to-energy conversions. The objective of this study is to further develop this technology by investigating the product distribution and quality from the HTL of food waste feedstocks. Four food waste feedstocks were selected for analysis: brewery grains, pear lees, coffee grounds, and honeydew skins. Solids analysis was conducted on each as-received feedstock, with the results determining dilution ratios for optimizing water content for HTL (≥80%). HTL conversions were conducted at 300 °C with a retention time of 30 min. Biochar was measured after product filtration, while ACP and bio-oil were measured via liquid–liquid phase separation. Coffee grounds produced the highest percentage of bio-oil (0.460%) and biochar (9.96%), while pear lees produced the highest percentage of ACP (89.5%). After quantification, ACP was characterized for nutrient concentrations. The quality of the ACP differed significantly from values in the literature, highlighting the influence of feedstock type and reaction conditions on HTL product characteristics (in addition to distribution) and underscoring the need for further research to optimize co-product utilization and process efficiency. Full article

Valorization of environmental waste into sustainable energy and value-added products offers a strategic pathway for advancing circular economic development and resource sustainability. In this study, waste cooking oil was converted into biodiesel using biogenically generated CaO, prepared thermally at 900 °C. The reaction process was modeled and optimized with a Taguchi orthogonal array L9(3⁴), considering four factors at three levels to yield nine experimental conditions. The model reliability was statistically validated through analysis of variance (ANOVA) at 95% confidence level (p < 0.05), achieving a high determination coefficient (R²) of 0.9965. The maximum biodiesel yield of 91.08% was obtained under the optimal conditions of the methanol to oil ratio of 15:1, a catalyst loading of 4.5 wt%, a reaction time of 90 min, a temperature of 65 °C, and a constant stirring speed of 650 rpm. The fuel property analysis confirmed compliance with international biodiesel and diesel standards). Economic evaluation of the process showed that integrating waste cooking oil with reusable seashell-derived catalysts enabled the production of high-quality biodiesel at R23.20 (~USD 1.39)/L, highlighting a sustainable and cost-competitive alternative to conventional feedstock. The study contributes to advancing waste-to-energy technologies and supports the transition towards a circular and sustainable energy future. Full article

In the Republic of Moldova, orchard biomass represents an important resource for the production of densified solid biofuels, with peach having the highest sustainable energy potential (33.5 ± 6.54 GJ·ha⁻¹). However, the quality of solid biofuels derived from orchard biomass is often constrained by heterogeneity in moisture content, uneven particle size distribution, and inadequate drying or blending practices along the supply chain. Optimizing the solid biofuel supply chain is therefore essential to minimize feedstock variability, ensure consistent densification quality, and reduce production costs. The aim of this study was to improve the process of producing densified solid biofuels from orchard biomass. Specifically, the study investigated how raw material moisture and particle size influence briquette density and durability, and how ternary mixtures of peach biomass, wheat straw, and sunflower residues can be optimized for enhanced energy performance. All experimental determinations were performed using validated methods and calibrated equipment. The results showed that optimal performance is achieved by shredding the biomass with 4–8 mm sieves and maintaining the moisture content between 6 and 14%, resulting in briquettes with the density of 1.00–1.05 g·cm⁻³, ash content below 3–5%, and an energy yield of 18.4–19.2 MJ·kg⁻¹. Ternary diagrams confirmed the decisive role of peach lignocellulosic residues in achieving high density, low ash content, and increased energy yield, while wheat straw and sunflower residues can be used in controlled proportions to diversify resources and reduce costs. These findings provide quantitative insights into how mixture formulation and process parameters influence the briquette quality, contributing to the optimization of solid biofuel supply chains for orchard and agricultural residues. Overall, this study demonstrates that competitive solid biofuels can be produced through careful balancing of mixture composition and optimization of technological parameters, offering practical guidelines for sustainable bioenergy development in regions with abundant orchard residues. Full article

With the rapid development of the photovoltaic (PV) and semiconductor fields, the reserves of traditional high-purity quartz raw materials can no longer meet the demands of various industries, creating an urgent need to develop new types of high-purity quartz feedstock. In this study, three groups of vein quartz samples from different mining areas were subjected to calcination at 950 °C for 2 h. The impurity states of the vein quartz before and after calcination were characterized using XRD, ICP, Raman and XRF. The migration behavior of metal cations in vein quartz under high-temperature conditions was systematically investigated, and the structural changes in the vein quartz before and after calcination were discussed from the perspectives of impurity element distribution and phase transformation. The results demonstrate that impurity cations in vein quartz migrate from the interior to the surface of the material under high-temperature environments. Quantitative ICP analysis of the inner and outer layers of the quartz samples before and after calcination revealed that, among the three groups, the surface impurity cation content of the sample with the most pronounced migration effect reached four times that of its internal structure. Combined with other characterization techniques, it was confirmed that after the cation migration process, the vein quartz samples exhibited a layered structure from the surface to the interior: a hematite mineralized layer, a high lattice impurity layer, and a low lattice impurity layer. This indicates that high-purity vein quartz with low lattice impurity content can be obtained by subjecting quartz to high-temperature calcination and subsequently removing the mineralized layer and the surface high lattice impurity layer. Consequently, vein quartz of ordinary quality can also be converted into high-purity quartz raw material of 4N grade or higher through the processes of cation migration and tailing removal. Full article

Lignocellulosic biomass wastes are renewable carbon resources that can be available for conversion into biofuels. There is a growing interest in utilizing a broader range of alternative biomass feedstocks such as agri-crop residues aside from the traditional forest-origin wood residues for fuel pellet production. However, crop residues typically have low and inconsistent fuel quality. This paper investigated the effectiveness of the combined steam explosion and water leaching pretreatment techniques to upgrade the fuel properties of wheat straw. The experimental treatments involved auto-catalyzed steam explosion and acid-catalyzed steam with and without subsequent water leaching. Using steam explosion catalyzed by dilute H₂SO₄ at a low concentration of 0.5 wt%, results showed the highest ash, Si, and Ca removal efficiencies of 82.2%, 91.1%, and 74.3%, respectively. Moreover, there was significant improvement in fuel quality in terms of fuel ratio (0.34) and calorific value HHV (21.9 MJ/kg), as well as a pronounced increase in the comprehensive combustibility index at the devolatization stage, indicating better combustion characteristics. Overall, the results demonstrate that with adequate pretreatment, the quality of agri-pellets derived from wheat straw could potentially be on par with wood pellets that are utilized for heat and power generation and residential heating. To mitigate the dry matter loss due to steam explosion, future studies shall consider using the process effluent to produce biofuel. Full article

This systematic review aimed to examine recent advances (2021–2025) in the conversion of agricultural biomass into biomaterials, biofertilizers, and bioproducts. Studies were included when addressing biomass types, pretreatment methods, conversion technologies, or resulting applications. Non-agricultural biomass, non-original research, and works outside the defined timeframe were excluded. Literature was identified in Scopus and Web of Science, complemented by Espacenet, Google Scholar, and institutional databases (USDA, FAO, IRRI, ABARES, UNICA, and CONAB, among others), totaling 108 documents referenced in this work. Risk of bias was minimized through predefined eligibility criteria and full-text assessment. Results were narratively synthesized, supported by figures and tables highlighting technological trends. Studies involving a wide range of agricultural biomasses (e.g., rice straw, corn stover, wheat straw, and sugarcane bagasse) were evaluated. Main outcomes included the development of bioplastics, biofoams, composites, hydrogels, bioceramics, biochar-based fertilizers, organic acids, enzymes, and green solvents. Evidence consistently indicated that pretreatment strongly influences conversion efficiency and that enzymatic and thermochemical routes show the highest potential for integrated biorefineries. Limitations included heterogeneity in biomass composition, variability in methodological quality, and scarcity of large-scale studies. Overall, findings underscore agricultural biomass as a strategic feedstock for circular bioeconomy models, with implications for sustainable materials, renewable energy, and low-carbon agriculture. Continued innovation, supportive policies, and improved logistics are essential for scaling biomass-based technologies. Full article

Hydrochar is a carbon-rich material produced through the hydrothermal carbonization (HTC) of wet biomass such as sewage sludge. Its nitrogen content is a critical quality parameter, influencing its suitability for use as a soil amendment and its potential environmental impacts. This study develops a high-accuracy ensemble machine learning framework to predict the nitrogen content of hydrochar derived from sewage sludge based on feedstock compositions and HTC process conditions. Four ensemble algorithms—Gradient Boosting Regression Trees (GBRTs), AdaBoost, Light Gradient Boosting Machine (LightGBM), and eXtreme Gradient Boosting (XGBoost)—were trained using an 80/20 train–test split and evaluated through standard statistical metrics. GBRT and XGBoost provided the best performance, achieving R² values of 0.993 and 0.989 and RMSE values of 0.169 and 0.213 during training, while maintaining strong predictive capabilities on the test dataset. SHAP analyses identified nitrogen content, ash content, and heating temperature as the most influential predictors of hydrochar nitrogen levels. Predicting nitrogen behaviour during HTC is environmentally relevant, as the improper management of nitrogen-rich hydrochar residues can contribute to nitrogen leaching, eutrophication, and disruption of aquatic biogeochemical cycles. The proposed ensemble-based modelling approach therefore offers a reliable tool for optimizing HTC operations, supporting sustainable sludge valorisation, and reducing environmental risks associated with nitrogen emissions. Full article

The incorporation of cattle slurry in soil in short-rotation-cycle poplar cultivations can be a win–win strategy, insofar as a main feedstock derived from local intensive dairy cattle breeding can be used as a natural fertilizer and in bioenergy produced in the same region. The circularity of this process can contribute to boosting local socio-economic value. In this context, this work involved the installation of a poplar SRC plantation with a density of 5330 trees ha⁻¹ in a 4000 m² moderately fertile flat site, which was formerly used as a vineyard. Mechanical dosages of slurry of 0, 26.6, 53.2, and 106.5 Mg ha⁻¹, designated as treatments T0, T1, T2, and T3, were applied three times per year during 2019, 2020, and 2021. The variables quantified were related to plant growth, biomass productivity and mass balances of K, P, Cu, Zn, Mg, and N, and organic matter in the whole soil, plant, and slurry system during the first rotation cycle. For treatments T0 and T1, all these seven chemical components showed positive balances in the system, with cumulative demand by soil and biomass being higher than cumulative supply by slurry. Negative balances occurred for P with T2 and T3 and for Zn with T3, so that an overall condition of nutrient saturation of the whole system was not achieved. A no-slurry application, or at most a moderate application equivalent to T1, in the second rotation cycle should therefore be prescribed to allow a nutrient equilibrium status to be achieved through internal seasonal recycling mechanisms. The biomass average productivities ranged from 6.1 to 11.8 Mg ha⁻¹ y⁻¹, peaking under treatment T2, and are within the typical values for a first rotation cycle for poplar SRCs. The biomass fuel quality was not affected by the slurry treatments. A good performance of plant total height and growth in diameter at breast height suggested that poplar trees were not stressed by the applied slurry. Only treatment T1 could assure that cattle CO₂-eq methane emissions were overall equilibrated by the carbon sequestration from poplar cultivation, with an absence of climatic-warming impacts. Treatments T2 and T3 could only partially minimize that impact, which would always exist. Globally, this site-specific analysis showed that, under moderately fertile conditions, controlled cattle slurry fertilization of poplar SRC cultivations, which would assure a long-term steady-state equilibrium, can be a viable option to contribute to decentralized production of bioenergy in rural communities. Full article

The rapid accumulation of plastic and textile waste, particularly polyethylene terephthalate (PET), has emerged as a global challenge for sustainable resource management. Conventional recycling methods, including mechanical and chemical routes, recover limited value and often degrade material quality while consuming substantial energy. Biocatalytic recycling, by contrast, offers a resource-efficient alternative that transforms post-consumer PET into high-purity monomers under mild and environmentally benign conditions. This review examines advances in enzymatic PET depolymerization, focusing on hydrolases such as cutinases, PETases, MHETases, and lipases. The discussion highlights enzyme engineering, reactor design, and process integration that improve kinetics, thermostability, and yield. From a resource perspective, biocatalytic recycling redefines PET waste as a renewable carbon feedstock capable of re-entering industrial cycles, thereby reducing reliance on virgin petrochemicals and mitigating greenhouse gas emissions. Ultimately, this review positions biocatalytic PET recycling as a cornerstone technology for achieving circularity and advancing global resource sustainability. Full article

Biomethane is increasingly regarded as a renewable fuel with a pivotal role in sustainable energy transitions, largely produced through the anaerobic fermentation of organic feedstocks. This work offers a comprehensive overview of its development, addressing the current status of production, management, and utilization within a broad energy context. Technological progress in fermentation-based biogas generation, upgrading, and purification is reviewed, with particular attention to innovations that enhance process efficiency and fuel quality. The analysis also highlights the importance of policy frameworks, incentives, and infrastructure in fostering large-scale deployment, alongside international cooperation to harmonize standards. Emerging trends such as decentralized fermentation units, integration with agricultural systems, and synergies with Power-to-Gas and carbon capture strategies are emphasized as promising pathways. Results underline that innovation, investment, and process optimization are key to improving competitiveness. In conclusion, biomethane derived from fermentation processes is poised to become a cornerstone of low-carbon energy systems, provided that technological advances and supportive policies align with sustainability objectives. Full article

The present study explores the production of metallized titanomagnetite briquettes, with a view to addressing two key issues. Firstly, it seeks to address the growing shortage of high-quality iron-bearing raw materials. Secondly, it looks at how to meet the increasingly stringent environmental constraints. The conventional blast-furnace treatment of titanomagnetite is hindered by the formation of refractory Ti-rich slags. It is hereby proposed that a single-cycle briquetting process in conjunction with a thermal reduction route should be utilized. This approach enables precise regulation of the Fe/flux ratio. Experiments were conducted on a low-grade titanomagnetite concentrate (68.5% Fe) from the Pervouralsk deposit (Russia). Cylindrical briquettes (D 15–20 mm, h 8–10 mm) were subjected to a pressure of 300 MPa during the pressing process, with the utilization of diverse binders comprising rubber cement, CaO, graphite + water, and basic oxygen-furnace (BOF) slag + sodium silicate. Following an oxidative pre-heating process at 1300 °C for two hours, followed by a gas-based reduction process at 1050 °C for three hours, with a CO/N₂ ratio of 90/10, the products demonstrated an oxidation rate of 85–95% and a cold compression strength of 16–80 MPa. The highest observed strength (80 MPa) was obtained with a binder comprising CaO·MgO·2SiO₂ (diopside/merwinite), which forms a low-viscosity melt, fills 90% of pores and crystallizes as acicular Mg-SFCA-I during cooling. Conversely, the CaO·TiO₂ and FeO·TiO₂ + Fe₃C associations yield brittle structures and a maximum strength of 16 MPa. The optimum briquette (0.55% CaO, D/H = 20/10 mm) exhibited a 95.7% metallization degree, a compressive strength of 48.9 MPa, and dimensional changes within acceptable limits, thus fulfilling the requirements for electric arc furnace feedstock. Further research is required in the form of a full Life Cycle Assessment and pilot-scale testing. However, the results obtained thus far confirm that titanomagnetite briquettes with a binder consisting of CaO, MgO and SiO₂ are a promising alternative to pellets for low-carbon steelmaking. Full article

Biomass is commonly used for cooking in developing countries, but traditional cookstoves emit pollutants (CO, NO_x, PM), which harm indoor air quality. Improvements and solutions are essential for achieving Sustainable Development Goal 7 (SDG 7). This study assesses the impact of the combustion chamber design, the combustion-air/gasification-air ratio (CA/GA = 2.8, 3.0, and 3.2), and the start type of water boiling test (WBT) protocol (cold and hot starts) on the chemical and morphological characteristics of the total suspended particulate matter (TSPM) emitted from a biomass gasification-based cookstove using densified biomass as feedstock. TSPM was characterized using Fourier-Transform Infrared Spectroscopy (FTIR), X-ray Photoelectron Spectroscopy (XPS), Raman Spectroscopy, and Transmission Electron Microscopy (TEM) to evaluate their chemical composition and morphological features under the above operational conditions. Under the modified WBT protocol, the cookstove achieved CO levels ranging from 1.52 to 2.13 g/MJ_d, and efficiency between 26.56% and 27.81%. TSPM emissions ranged between ~74 and 122.70 mg/MJ_d. The chemical characteristics of TSPM surface functional groups weren’t affected by the start condition, except for decreased intensities as CA/GA increased, promoting oxidation and removal as CO/CO₂. While cold start produced TSPM with higher structural order at higher CA/GA levels, no significant differences were observed among samples from both start conditions at CA/GA ≥ 3.0, indicating chemical and structural similarity. Morphology and particle size were mainly unaffected, with only slight increases in particle size during hot start due to higher biomass-to-air ratios. Full article

The global demand for compost, produced through the bioconversion of organic waste into nutrient-rich soil amendments, is increasing due to the adverse environmental, health, and economic impacts of synthetic fertilizers. Compost use offers a cost-effective and sustainable alternative, improving soil fertility and long-term productivity. However, the potential of tobacco waste as a composting substrate remains insufficiently investigated. This study aimed to evaluate the feasibility of utilizing tobacco waste as a composting feedstock and to develop an optimized composting method. Tobacco waste (scrap leaves and midrib stems) was composted with cow manure in earthen pots to promote decomposition and nutrient mineralization, and its performance was compared with compost produced from cow manure and vegetable waste (vegetable leaves). Vermicomposting, which involves the addition of earthworms to conventional compost treatments, was also implemented to enhance composting efficiency and nutrient release. The final composts, both conventional and vermicompost, were analyzed for organic carbon (OC), nitrogen (N), phosphorus (P), potassium (K), sulfur (S), and the maturity duration. Among the three conventional compost variants, the mixture of cow manure and tobacco leaves had the highest nitrogen concentration at 1.45% and the cow manure and tobacco stems had 1.23% as the second best. Cow manure and tobacco stem compost had the highest K content of 1.13%, followed by tobacco leaves (0.99%). Sulfur levels were also found to be higher in the tobacco stem compost compared to the other compost types, with the highest value of 0.56%, followed by tobacco leaves (0.23%). All three vermicompost variants outperformed their conventional counterparts in terms of nutrient concentrations and achieved maturity in shorter durations. The cow manure with tobacco stem mixed vermicompost was notable for its elevated potassium (1.35%) and sulfur (0.89%) contents. The results indicate that vermicomposting offers a faster and more nutrient-enriched composting approach, particularly with tobacco waste. Incorporating tobacco waste into this process has the potential to produce high-quality compost, presenting a sustainable strategy for waste valorization and enhancing soil fertility. Full article