Search Results (47)

Alginate is the main structural polysaccharide in brown algal cell walls and is widely used in pharmaceuticals, textiles, cosmetics, feed, and other fields. Its tradition production methods feature low yield, high water consumption and environmental pollution, which need industrial upgrading. In this study, Aeromonas hydrophila W-02, a bacterial strain capable of simultaneously producing high levels of cellulase, pectinase, and glucanase, was isolated and identified from kelp humic liquid. Genome sequencing revealed that it has 5781 genes, 116 of which are related to glycoside hydrolysis. When A. hydrophila W-02 was applied to kelp for alginate extraction, the optimized bacterial method achieved a 38.21% yield, four times that of the traditional acid coagulation–acidification method (8.12%). Alginate was used to prepare alginate fiber and its performance indices were compared with those of commercial fibers. Scanning electron microscopy and mechanical properties analysis revealed no significant difference between alginate fibers from this novel process and commercial alginate. This study provides an efficient and green approach for alginate preparation and provides data to support the industrialization of high-efficiency bio-based alginate extraction. Full article

Coagulation–flocculation is widely recognized as a fundamental step in wastewater treatment, as it promotes the aggregation and removal of suspended particles and organic contaminants following the addition of a coagulant. In this study, a bio-based coagulant was prepared from prickly pear (Opuntia ficus-indica) seed residues obtained after essential oil extraction. The extraction process for bioactive agents was successfully modeled using Central Composite Design (CCD)-based Response Surface Methodology (RSM). Optimal extraction was reached at pH 13, PPSM of 7.5 g, 0.75 M NaCl, and 40 min of stirring, providing maximum yields of 69.63 g proteins, 217.075 g total sugars, and 81.416 g polyphenols. The optimized extract was subsequently used as a bio-coagulant for the treatment of wastewater collected from the Chalghoum El Aid–Oued El Athmania wastewater treatment plant (Mila, Algeria). The effects of three operating parameters, initial turbidity, solution pH, and bio-coagulant dosage, on the coagulation–flocculation performance were investigated using a Box–Behnken design (BBD). Process efficiency was evaluated in terms of turbidity, chemical oxygen demand (COD), and organic matter (OM) removal. The raw wastewater exhibited initial values of 200 NTU for turbidity, 640 mg/L for COD, and 25 for organic matter. Statistical analysis revealed that the developed quadratic models were highly significant (p ≤ 0.05) and showed excellent predictive performance, with coefficients of determination (R² ≥ 0.97). Optimal treatment conditions were identified at pH 7, a bio-coagulant dosage of 1 mL/L, and an initial turbidity of 200 NTU. Under these conditions, removal efficiencies exceeded 98% for turbidity and COD and reached 88.08% for organic matter. Furthermore, Fourier-Transform Infrared (FTIR) Spectroscopy analysis confirmed the presence of functional groups responsible for the coagulation activity of the bio-coagulant. These findings highlight the potential of prickly pear seed residues as an effective, sustainable, and low-cost alternative to conventional chemical coagulants in wastewater treatment. Full article

This study presents a comprehensive multi-objective optimization of sewage wastewater treatment using bio-based coagulants, guided by the Grey Wolf Optimizer (GWO) and its multi-objective variant (MOGWO). Experimental coagulation data, employing Citrullus lanatus and Cucumis melo as natural coagulants, were modeled using multivariate regression techniques, yielding high coefficients of determination (R² > 0.95) across key water quality parameters. The optimization process targeted maximal reductions in turbidity, total suspended solids (TSS), biochemical oxygen demand (BOD), and chemical oxygen demand (COD) through strategic manipulation of pH and coagulant dosage. The single-objective GWO achieved significant outcomes, including a 96.68% turbidity reduction at pH 5 and 50 mg/L dosage. The MOGWO algorithm identified Pareto-optimal solutions, such as a 94.2% turbidity reduction at pH 5 and 72 mg/L dosage, and a balanced BOD reduction of 52.7% at pH 7. The predictive models indicated that optimal treatment conditions could reduce chemical usage by up to 90% compared to conventional coagulants, resulting in potential cost savings of up to 30%. Moreover, the algorithms demonstrated rapid convergence, averaging 200 iterations, highlighting their computational efficiency and robustness. These findings illustrate that integrating bio-based coagulants with advanced optimization techniques can achieve high treatment efficiency while reducing chemical inputs, thus directly supporting environmental sustainability by minimizing sludge and secondary pollution. In this situation, the wastewater treatment plant will focus on resource-recovery systems with less or no waste at the end of the treatment process. This approach aligns with circular economy principles by promoting eco-friendly, cost-effective wastewater treatment solutions suitable for resource-limited settings. The study offers a forward-looking pathway for environmentally responsible wastewater management practices that significantly reduce chemical dependency and contribute to pollution mitigation efforts. Full article

This study investigates the potential of Quercus robur leaves as a bio-coagulant for the removal of heavy metal ions, including zinc (II), iron (III), copper (II), and chromium (VI), from water. The Quercus robur leaves were used in two forms: Quercus robur powder (QRP) and Quercus robur extract (QRE). The extract was prepared using distilled water to extract the active compounds responsible for coagulation, such as proteins, polysaccharides, and total phenolics. The QRP was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and zeta potential analysis to identify the active functional groups, surface morphology, crystallinity, and surface charge, all of which are key factors influencing its performance in the coagulation–flocculation process. In this work, the Response Surface Methodology (RSM)-based Central Composite Design (CCD), with two factors (bio-coagulant dosage and initial metal concentration), was used examine the effects of each factor and their interaction, while the responses were zinc (II) removal, iron (III) removal, copper (II) removal, and chromium (VI). The results revealed high removal efficiency for these metal ions, reaching up to 100% for all metal ions treated with QRP and QRE. The quality of the model predictions was evaluated using analysis of variance (ANOVA). For all metal ions, the R² (≥97%), R² adjusted (≥95%), and p-values (<0.05), indicating an excellent model accuracy. These results show that bio-coagulants (QRP and QRE) based a Quercus robur leaves are a promising, effective, and reliable option for removing heavy metal ions from water, and that the models developed can be used to optimize the coagulation-flocculation process. Full article

In this study, we used CTS and DMDAAC as raw materials and prepared a novel chitosan graft copolymer, CTS-g-PDMDAAC, through UV initiation in the presence of the photoinitiator VA-044. The synthesis process was systematically optimized, and its structural characteristics and performance in water treatment were evaluated. A single-factor experiment determined the optimal synthesis conditions to be a mass ratio of chitosan to DMDAAC of 1:4, total reactant concentration of 15.5%, ultraviolet light exposure for 5 h, and concentration of VA-044 of 0.2%. CTS-g-PDMDAAC demonstrated superior performance overall to CTS according to various characterization methods, such as FTIR, XPS, XRD, and BET. The coagulation experiment showed that at a dosage of 6.0 mg/L, the removal rates of residual turbidity and chlorophyll a reach 0.58 NTU and 99.37%, respectively, and the generated flocs have a dense structure and exhibit strong shear resistance. Finally, the flocculation mechanism was explored. Compared with traditional flocculants, CTS-g-PDMDAAC has the advantages of efficient algae removal, lower sludge production, no secondary pollution, and potential for the utilization of microalgae. This research provides theoretical support and suggests technical pathways for the development of biobased, environmentally friendly flocculants with broad pH adaptability. Full article

The removal of copper–cyanide complexes from cyanide gold leaching tail water poses a significant challenge, as they are difficult to eliminate and risk causing secondary pollution. This study developed a synergistic flocculation–flotation process using the bio-collector sodium cocoyl glycinate (SCG) and the coagulant polyferric sulfate (PFS) for purification. Simulated wastewater, prepared based on actual gold mine effluent, was treated under optimized conditions of reagent dosage, a solution pH of 6–10, and a flotation time of 1–5 min, achieving high removal efficiencies of 96.48% for copper and 94.68% for total cyanide. Mechanistic studies via FT-IR, Zeta potential, and XPS revealed that Fe³⁺ from PFS formed Fe-CN complexes with both free and copper-complexed cyanide. Simultaneously, copper ions coordinated with SCG to generate a hydrophobic Fe-CN-Cu-SCG ternary complex, which was subsequently removed by adsorption onto air bubbles via the hydrophobic chains of SCG. This work provides a novel, efficient, and mechanistically clear strategy for the advanced treatment of cyanide-containing tailing water with a gold content of 0.021 mg/L. Full article

The coagulation cascade triggered by the contact between blood and the surface of implantable/interventional devices can lead to thrombosis, severely compromising the long-term safety and efficacy of medical devices. As an alternative to systemic anticoagulants, surface anticoagulant modification technology can achieve safer hemocompatibility on the device surface, holding significant potential for clinical application. This article systematically elaborates on the latest research progress in the surface anticoagulant modification of blood-contacting materials. It analyzes and discusses the main strategies and their evolution, spanning from physically inert carbon-based coatings and heparin-based drug-functionalized surfaces to hydrophilic/hydrophobic dynamic physical barriers, biologically signaling regulatory coatings, and bio-integrative/regenerative endothelium-mimicking surfaces. The advantages and limitations of the respective methods are outlined, and the potential for synergistic application of multiple strategies is explored. A special emphasis is placed on current research hotspots regarding novel anticoagulant surface technologies, such as hydrogel coatings, liquid-infused surfaces, and 3D-printed endothelialization, aiming to provide insights and references for developing long-term, safe, and hemocompatible cardiovascular implantable devices. Full article

Leachate from the Magtaa Kheira landfill exhibits complex physicochemical characteristics that restrict the efficacy of single-treatment processes. This study assessed a sustainable two-stage treatment strategy combining coagulation–flocculation and adsorption. During the initial stage of the study, both aluminum sulfate (AS) and a bio-based coagulant derived from Moringa oleifera seeds (MOS) were evaluated for their effectiveness in the pretreatment of leachate. Box–Behnken Design combined with Response Surface Methodology was used to optimize the coagulation process using aluminum sulfate (AS). The highest removal efficiencies were 91% for turbidity and 85% for chemical oxygen demand (COD) removal, achieved at an AS concentration of 1.44 g·L⁻¹ and an initial pH of 8. In parallel, the performance of MOS extract was investigated as an eco-friendly alternative to AS. An FTIR analysis revealed the presence of protein-associated hydroxyl (3288 cm⁻¹) and carboxyl and amine groups (1647 cm⁻¹), which are integral to destabilization via hydrogen bonding, while SEM confirmed a surface morphology conducive to effective floc formation. MOS demonstrated comparable turbidity removal to AS, significantly reducing both sludge generation and chemical consumption. Following the coagulation stage, treated leachates were passed through a granular activated carbon (GAC) column, enhancing overall COD removal to over 94% to reach acceptable discharge and reuse levels. The coagulation–adsorption sequence, incorporating both chemical and bio-based coagulants, provides an efficient and sustainable approach for the treatment of complex leachate, addressing both performance and environmental considerations. Full article

Coagulation–sedimentation remains a widely used process in drinking and wastewater treatment, yet its performance for emerging contaminants requires further evaluation. This review summarizes recent advances in conventional and novel coagulant systems for the removal of pesticides, pharmaceuticals, per- and polyfluoroalkyl substances (PFAS), natural organic matter (NOM), and micro- and nanoplastics (MNPs). The efficiency of conventional aluminum- and iron-based coagulants typically ranges from 30–90% for NOM and pesticides, 10–60% for pharmaceuticals, <20% for PFAS, and up to 95% for microplastics. Modified and hybrid materials, including titanium-based and bio-derived coagulants, demonstrate superior performance through combined mechanisms of charge neutralization, adsorption, and complexation. The zeta potential of particles was identified as a key factor in optimizing MNP removal. The ability of iron and titanium to form complexes with organic ligands significantly influences the removal of organic pollutants and metal–organic interactions in water matrices. While most research remains at the laboratory scale, promising developments in hybrid and electrocoagulation systems indicate potential for field-scale application. The review highlights that coagulation is best applied as a pretreatment step in integrated systems, enhancing subsequent adsorption, oxidation, or membrane processes. Future studies should focus on large-scale validation, energy efficiency, and the recovery of metal oxides (e.g., TiO₂) from residual sludge to improve sustainability. Full article

Coagulation–flocculation, historically reliant on simple inorganic salts, has evolved into a technically sophisticated process that is central to the removal of turbidity, suspended solids, organic matter, and an expanding array of micropollutants from complex wastewaters. This review synthesizes six decades of research, charting the transition from classical aluminum and iron salts to high-performance polymeric, biosourced, and hybrid coagulants, and examines their comparative efficiency across multiple performance indicators—turbidity removal (>95%), COD/BOD reduction (up to 90%), and heavy metal abatement (>90%). Emphasis is placed on recent innovations, including magnetic composites, bio–mineral hybrids, and functionalized nanostructures, which integrate multiple mechanisms—charge neutralization, sweep flocculation, polymer bridging, and targeted adsorption—within a single formulation. Beyond performance, the review highlights persistent scientific gaps: incomplete understanding of molecular-scale interactions between coagulants and emerging contaminants such as microplastics, per- and polyfluoroalkyl substances (PFAS), and engineered nanoparticles; limited real-time analysis of flocculation kinetics and floc structural evolution; and the absence of predictive, mechanistically grounded models linking influent chemistry, coagulant properties, and operational parameters. Addressing these knowledge gaps is essential for transitioning from empirical dosing strategies to fully optimized, data-driven control. The integration of advanced coagulation into modular treatment trains, coupled with IoT-enabled sensors, zeta potential monitoring, and AI-based control algorithms, offers the potential to create “Coagulation 4.0” systems—adaptive, efficient, and embedded within circular economy frameworks. In this paradigm, treatment objectives extend beyond regulatory compliance to include resource recovery from coagulation sludge (nutrients, rare metals, construction materials) and substantial reductions in chemical and energy footprints. By uniting advances in material science, process engineering, and real-time control, coagulation–flocculation can retain its central role in water treatment while redefining its contribution to sustainability. In the systems envisioned here, every floc becomes both a vehicle for contaminant removal and a functional carrier in the broader water–energy–resource nexus. Full article

Microplastic pollution represents a significant environmental challenge, as microplastics accumulate in effluents and soils, causing serious risks to ecosystems and human health. Efficient removal of these contaminants is essential to mitigate their potential adverse effects. This review summarizes and critically analyses current methods for the removal of microplastics from effluents and soils, focusing on their effectiveness, advantages, and limitations. Conventional techniques—including filtration, flotation, chemical coagulation, flocculation, and adsorption—are discussed in the context of wastewater treatment and soil remediation. Emerging approaches, such as flocculation processes with special focus on the application of bio-based flocculants, are also highlighted as promising solutions. Key challenges in microplastic removal, including the diversity of microplastic types, their small size, and the complexity of environmental matrices, are addressed. This work intends to contribute to the urgent need for further research to develop more efficient and sustainable strategies for microplastic removal from environmental systems. Full article

Arsenic contamination in water poses a significant global health risk, necessitating efficient and sustainable remediation strategies. Arsenic contamination affects groundwater in at least 106 countries, potentially exposing over 200 million people to elevated levels, primarily through contaminated drinking water. Among the most affected regions, Bangladesh remains a critical case study, where widespread reliance on shallow tubewells has resulted in one of the largest mass poisonings in history. Bio-based nanomaterials have emerged as promising solutions due to their eco-friendly nature, cost-effectiveness, and high adsorption capabilities. These nanomaterials offer a sustainable approach to arsenic remediation, utilizing materials like biochar, modified biopolymers, and bio-based aerogels, which can effectively adsorb arsenic and other pollutants. The use of environmentally friendly nanostructures provides a potential option for improving the efficiency and sustainability of arsenic remediation from groundwater. This review explores the mechanisms underlying arsenic remediation using such nanomaterials, including adsorption, filtration/membrane technology, photocatalysis, redox reactions, complexation, ion exchange, and coagulation–flocculation. Despite their potential, challenges such as scalability, stability, and regeneration hinder widespread application. We discuss recent advancements in material design, surface modifications, and hybrid systems that enhance performance. Finally, future perspectives are highlighted, including the integration of these bio-derived systems with smart sensing technologies, sustainable water-treatment frameworks, smart design, and life-cycle integration strategies, particularly for use in resource-constrained regions like Bangladesh and other globally impacted areas. Full article

High turbidity in raw water poses a major challenge to drinking water quality and requires effective, sustainable treatment solutions. This work investigates the reduction in turbidity in raw water and the enhancement of overall drinking water quality through the coagulation–flocculation process. The performance of Pine cone extract as a bio-coagulant was evaluated using four different solvent-based extractions (PC-H₂O, PC-HCl, PC-NaCl, and PC-NaOH). The effects of key operational parameters were analyzed, and jar tests were carried out to enhance the coagulation–flocculation process by identifying the optimal conditions. Experimental design was further refined using RSM based on a BBD, incorporating three factors: initial pH, coagulant dosage, and settling time, with turbidity removal efficiency as the response variable. Statistical analysis confirmed that initial pH, coagulant dosage, and settling time significantly influenced turbidity reduction at a confidence level of p-value < 0.05 for all four solvents. Among the extracts tested, PC-HCl demonstrated the highest turbidity removal efficiency. The optimal conditions achieving 78.57% turbidity reduction were a pH of 8.5, a coagulant dosage of 100 mL/L, and a settling time of 120 min. These findings highlight the significant potential of Pine cone extract as an effective, sustainable, and eco-friendly organic coagulant for raw water treatment. Full article

This paper applies a semi-quantitative approach to review the diversity, environmental controls, detection methods, human health risks, and mitigation of cyanotoxins in drinking water systems (DWSs). It discusses the environmental factors controlling the occurrence of cyanotoxins, presents the merits and limitations of emerging methods of their detection (qPCR, liquid chromatography–mass spectrometry, and electrochemical biosensors), and outlines the human exposure pathways and health outcomes with identification of high-risk groups and settings. High-risk groups include (1) communities relying on untreated drinking water from unsafe, polluted water sources and (2) low-income countries where cyanotoxins are not routinely monitored in DWSs. The fate and behavior processes are discussed, including removing cyanotoxins in DWSs based on conventional and advanced treatment processes. The available methods for cyanotoxin removal presented in this paper include (1) polymer-based adsorbents, (2) coagulation/flocculation, (3) advanced oxidation processes, (4) ultra- and nanofiltration, and (5) multi-soil layer systems. Future research should address (1) detection and fate in storage and conveyance facilities and at the point of consumption, (2) degradation pathways and toxicity of by-products or metabolites, (3) interactive health effects of cyanotoxins with legacy and emerging contaminants, (4) removal by low-cost treatment techniques (e.g., solar disinfection, boiling, bio-sand filtration, and chlorination), (5) quantitative health risk profiling of high-risk groups, and (6) epidemiological studies to link the prevalence of human health outcomes (e.g., cancer) to cyanotoxins in DWSs. Full article

This study explores the extraction and utilization of tannins from Acacia sp. bark residues for water treatment applications. As a by-product of forest management, Acacia sp. bark is valorized through tannin-based coagulant production, contributing to the circular (bio)economy. A systematic review with bibliometric analysis was first conducted to assess the technical–scientific landscape, identifying methodologies and technologies applied to extract and produce natural tannin-based coagulants from Acacia sp. bark residues for water treatment. From the portfolio of analyzed publications, and which followed the thematic axis addressed and the inclusion criteria, only a single study focuses on performing a life cycle assessment (LCA). Due to the relevance of the topic and the clear lack of existing literature, an environmental assessment of the extraction and production of condensed tannins was performed using the LCA methodology from a gate-to-gate perspective. Among the six process stages, spray drying and adsorption (purification) were the primary sources of environmental impact due to their high energy consumption and makeup ethanol use, respectively. The most effective strategy to enhance environmental performance would be reducing water consumption in extraction, thereby lowering energy demand in spray drying. Since both extraction and spray drying require significant energy, decreasing water use and allowing higher moisture content in the condensed tannin extract would mitigate energy consumption. The LCA study thus proved essential in guiding process development toward a reduced environmental footprint. Full article