Search Results (355)

As an efficient clean energy technology, water electrolysis for hydrogen production has its efficiency limited by the sluggish oxygen evolution reaction (OER) kinetics, which drives the demand for the development of high-performance anode OER catalysts. This work constructs bimetallic (Al, Mn) co-doped nanoporous spinel CoFe₂O₄ (np-CFO) with a tunable structure and composition as an OER catalyst through a simple two-step dealloying strategy. The as-formed np-CFO (Al and Mn) features a hierarchical flaky configuration; that is, there are a large number of fine nanosheets attached to the surface of a regular micron-sized flake, which not only increases the number of active sites but also enhances mass transport efficiency. Consequently, the optimized catalyst exhibits a low OER overpotential of only 320 mV at a current density of 10 mA cm⁻², a minimal Tafel slope of 45.09 mV dec⁻¹, and exceptional durability. Even under industrial conditions (6 M KOH, 60 °C), it only needs 1.83 V to achieve a current density of 500 mA cm⁻² and can maintain good stability for approximately 100 h at this high current density. Theoretical simulations indicate that Al and Mn co-doping could indeed optimize the electronic structure of CFO and thus decrease the energy barrier of OER to 1.35 eV. This work offers a practical approach towards synthesizing efficient and stable OER catalysts. Full article

Aluminum matrix composites provide an ideal solution for lightweight brake disks, but conventional casting processes are prone to crack initiation due to inhomogeneous reinforcement dispersion, gas porosity, and inadequate toughness. To break the conventional trade-off between high wear resistance and low toughness of brake disks, this study fabricated a bimetallic structure of SiC_p/Al–Fe–V–Si aluminum matrix composite and cast ZL101 alloy using friction stir lap welding (FSLW). Then, the microstructural evolution, mechanical properties, and tribological behavior of the FSLW joints were studied by XRD, SEM, TEM, tensile testing, and tribological tests. The results showed that the FSLW process homogenized the distribution of SiC particle reinforcements in the SiC_p/Al–Fe–V–Si composites. The Al₁₂(Fe,V)₃Si heat-resistant phase was not decomposed or coarsened, and the mechanical properties were maintained. The FSLW process refined the grains of the ZL101 aluminum alloy through recrystallization and fragmented eutectic silicon, improving elongation to 22%. A metallurgical bond formed at the joint interface. Tensile fracture occurred within the ZL101 matrix, demonstrating that the interfacial bond strength exceeded the alloy’s load-bearing capacity. In addition, the composites exhibited significantly enhanced wear resistance after FSLW, with their wear rate reduced by approximately 40% compared to the as-received materials, which was attributed to the homogenized SiC particle distribution and the activation of an oxidative wear mechanism. Full article

Hydrogen energy is a pivotal carrier for achieving carbon neutrality, requiring green and efficient production via water electrolysis. However, the anodic oxygen evolution reaction (OER) involves a sluggish four-electron transfer process, resulting in high overpotentials, while the prohibitive cost and complex preparation of precious metal catalysts impede large-scale commercialization. In this study, we develop a FeCo-based bimetallic deep eutectic solvent (FeCo-DES) as a multifunctional reaction medium for engineering a three-dimensional (3D) coral-like FeOOH-Co₂(OH)₃Cl/NF composite via a mild one-step impregnation approach (70 °C, ambient pressure). The FeCo-DES simultaneously serves as the solvent, metal source, and redox agent, driving the controlled in situ assembly of FeOOH-Co₂(OH)₃Cl hybrids on Ni(OH)₂/NiOOH-coated nickel foam (NF). This hierarchical architecture induces synergistic enhancement through geometric structural effects combined with multi-component electronic interactions. Consequently, the FeOOH-Co₂(OH)₃Cl/NF catalyst achieves a remarkably low overpotential of 197 mV at 100 mA cm⁻² and a Tafel slope of 65.9 mV dec⁻¹, along with 98% current retention over 24 h chronopotentiometry. This study pioneers a DES-mediated strategy for designing robust composite catalysts, establishing a scalable blueprint for high-performance and low-cost OER systems. Full article

The mixed oxides of Ni/ZrO₂, Ni-Ca/ZrO₂, Ni-Ba/ZrO₂, and Ni-Ba-Ca/ZrO₂ were prepared using the co-precipitation method at a pH of precisely 8.3. The catalytic mixed oxides of Ni/ZrO₂, Ni-Ca/ZrO₂, Ni-Ba/ZrO₂, and Ni-Ba-Ca/ZrO₂ were characterized using x-ray diffraction XRD, Brunauer Emmett Teller (BET), scanning electron microscopy (SEM), and metal dispersion for the screening of phase purity, surface area, and morphology. The mixed oxides are subjected to CO₂-TPD to quantify the basicity of every composition. The mixed oxide catalysts of Ni/ZrO₂, Ni-Ca/ZrO₂, Ni-Ba/ZrO₂, and Ni-Ba-Ca/ZrO₂ were screened for oxythermal reforming of CH₄ with CO₂ in a fixed bed tubular reactor at 800 °C. Among all catalysts, the Ba- and Ca- loaded Ni-Ba-Ca/ZrO₂ showed high conversion by the decomposition of methane and CO₂ disproportionation throughout the time on stream of 29 h. The high activity with stability led to less coke formation over Ni-Ba-Ca/ZrO₂ over the surface. The stable syngas production with an active catalyst bed contributed to the improved bimetallic synergy. The high surface basicity of Ni-Ba-Ca/ZrO₂ may keep actively gasifying the formed soot and allow for further stable reforming reactions. Full article

Surface segregation in bimetallic systems plays a critical role in material functionality, as electrochemical activity and catalytic performance are governed by the surface composition. To explore the influence of atomic oxygen on the surface composition of Pd–Ti alloys, density functional theory (DFT) simulations were utilized to analyze Ti segregation within Pd matrices. The adsorption behavior of atomic oxygen on Pd–Ti low-index (111), (100), and (110) surfaces was systematically investigated through energetic and electronic analyses. Simulation results reveal that Ti atoms prefer to remain in the bulk of the alloy under vacuum conditions, whereas oxygen adsorption induces significant Ti segregation to the surface layer. This oxygen-driven segregation is mechanistically linked to oxygen-surface bonding strength, as evidenced by correlating adsorption energetics with electronic structure modifications. These results provide a theoretical basis for engineering Pd–Ti alloys as high-performance catalysts in the oxygen reduction reaction. Full article

Acetone detection is crucial for non-invasive health monitoring and environmental safety, so there is an urgent demand to develop high-performance gas sensors. Here, platinum (Pt)-functionalized layered flower-like nickel ferrite (NiFe₂O₄) sheets were efficiently fabricated via facile hydrothermal synthesis and wet chemical reduction processes. When the Ni/Fe molar ratio is 1:1, the sensing material forms a Ni/NiO/NiFe₂O₄ composite, with performance further optimized by tuning Pt loading. At 1.5% Pt mass fraction, the sensor shows a high acetone response (R_g/R_a = 58.33 at 100 ppm), a 100 ppb detection limit, fast response/recovery times (7/245 s at 100 ppm), and excellent selectivity. The enhancement in performance originates from the synergistic effect of the structure and Pt loading: the layered flower-like morphology facilitates gas diffusion and charge transport, while Pt nanoparticles serve as active sites to lower the activation energy of acetone redox reactions. This work presents a novel strategy for designing high-performance volatile organic compound (VOC) sensors by combining hierarchical nanostructured transition metal ferrites with noble metal modifications. Full article

Overuse of tert-butylhydroquinone (TBHQ) as a food antioxidant has the potential to pollute the environment and threaten human health. Therefore, it is imperative to develop precise and rapid methods to detect TBHQ in food products. In this study, Fe- and Mn-doped Prussian blue analogs (FeMn-PBAs) were prepared by co-precipitation, FeMn-PBAs/PAN was prepared by electrostatic spinning, and a novel FeMn@C/CNFs composite was prepared by carbonization in nitrogen. Bimetallic FeMn doping has been shown to reduce vacancy defects and enhance the structural stability of PBA. Furthermore, electrostatic spinning has been demonstrated to reduce the agglomeration of PBA nanoparticles, which are electrode-modifying materials with high stability and good electrical conductivity. The morphological and structural characteristics of the FeMn@C/CNF composites were examined using scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The electrochemical behavior of tert-butyl hydroquinone in FeMn@C/CNFs was studied by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and chronocoulometry (CC). The results demonstrate that the sensor exhibits excellent repeatability, reproducibility, and anti-interference capabilities. The prepared electrochemical sensor can be effectively utilized for the detection of TBHQ in food samples such as soybean and peanut oil samples, proving its strong potential for practical applications. Full article

The selective catalytic reduction of NO_x with CH₄ (CH₄-SCR) holds the potential to simultaneously abate harmful NO_x and CH₄ greenhouse gases. In this study, a series of bimetallic M-In/H-SSZ-39 catalysts (where M represents Cr, Co, Ce, and Fe) were prepared via an ion exchange method and subsequently evaluated for their CH₄-SCR activity. The influences of the preparation parameters, including the metal ion concentration and calcination temperature, as well as the operating conditions, such as the CH₄/NO ratio, O₂ concentration, water vapor content, and gas hourly space velocity (GHSV), on the catalytic activity of the optimal Cr-In/H-SSZ-39 catalyst were meticulously examined. The results revealed that the Cr-In/H-SSZ-39 catalyst exhibited peak CH₄-SCR catalytic performance when the Cr(NO₃)₃ concentration was 0.0075 M, the In(NO₃)₃ concentration was 0.066 M, and the calcination temperature was 500 °C. Under optimal operating conditions, namely GHSV of 10,000 h⁻¹, 400 ppm NO, 800 ppm CH₄, 15 vol% O₂, and 6 vol% H₂O, the NO_x conversion rate reached 93.4%. To shed light on the excellent performance of Cr-In/H-SSZ-39 under humid conditions, a comparative analysis of the crystalline phase, chemical composition, pore structure, surface chemical state, surface acidity, and redox properties of Cr-In/H-SSZ-39 and In/H-SSZ-39 was conducted. The characterization results indicated that the incorporation of Cr into In/H-SSZ-39 enhanced its acidity and also facilitated the generation of InO⁺ active species, which promoted the oxidation of NO and the activation of CH₄, respectively. A synergistic effect was observed between Cr and In species, which significantly improved the redox properties of the catalyst. Consequently, the activated CH₄ could further interact with InO⁺ to produce carbon-containing intermediates such as HCOO⁻, which ultimately reacted with nitrate-based intermediates to yield N₂, CO₂, and H₂O. Full article

Nanostructured bimetallic IrSn composites deposited on the natural aluminosilicate montmorillonite were synthesized and evaluated as anode electrocatalysts for polymer electrolyte membrane electrolysis cells (PEMECs). The test series prepared via the sol–gel method consisted of samples with 30 wt. % total metal content and varying Ir:Sn ratio. The performed X-ray diffraction analysis and high-resolution transmission electron icroscopy registered very fine nanostructure of the composites with metal particles size of 2–3 nm homogeneously dispersed on the support surface and also intercalated in the basal space of its layered structure. The electrochemical behavior was investigated by cyclic voltammetry and steady-state polarization techniques. The initial screening was performed in 0.5 M H₂SO₄. Then, the catalysts were integrated as anodes in membrane electrode assemblies (MEAs) and tested in a custom-made PEMEC. The electrochemical tests revealed that the catalysts with Ir:Sn ratio 15:15 and 18:12 wt. % demonstrated high efficiency toward the oxygen evolution reaction during repetitive potential cycling and sustainable performance with current density in the range 140–120 mA cm⁻² at 1.6 V vs. RHE during long-term stability tests. The results obtained give credence to the studied IrSn/MMT nanocomposites to be considered promising, cost-efficient catalysts for the oxygen evolution reaction (OER). Full article

Bimetallic catalysts can effectively enhance the catalytic degradation efficiency of peroxymonosulfate (PMS), which is usually attributed to the enhancement of electron transfer, but currently, there is no clear explanation of the mechanism of how the electron transfer is enhanced. A nitrogen-doped Fe/Mn composite biochar (FeMn-NBC) was co-constructed by hydrothermal synthesis and high-temperature calcination. The FeMn-NBC activated PMS more efficiently than the monometallic one due to the enhanced electron transfer between Fe and Mn. The FeMn-NBC/PMS system activated PMS with Mn as the active center, and the high oxidation state of Mn⁴⁺ promoted the acceleration of the PMS adsorption of the generation of Mn²⁺/Mn³⁺. This gaining effect accelerated the electron cycling between Fe²⁺/Fe³⁺ and Mn²⁺/Mn³⁺/Mn⁴⁺, which enhanced the PMS catalysis to generate free radicals (•OH, SO₄^•− and •O₂⁻) and non-radicals (¹O₂) for the efficient degradation of diisobutyl phthalate (DIBP). Benefiting from this gaining effect, the degradation rate of DIBP by the FeMn-NBC/PMS system was increased by 2.43 and 3.38 times compared to Fe-NBC and Mn-NBC. The bimetallic-enhanced electron transfer mechanism proposed in this study facilitated the development of efficient catalysts for more efficient and selective removal of organic pollutants. Full article

Noble metals are widely recognized for their ability to catalyze the electro-oxidation of organic compounds, with smaller particle sizes significantly enhancing electrocatalytic activity. In this study, catalytic electrodes decorated with atomic-level platinum and Pt-Au clusters were fabricated using cyclic atomic-metal electrodeposition. The interactions between the iminium (protonated imine) groups in emeraldine salt polyaniline (PANI) and metal chloride complexes in the electrolyte enabled precise control over the cluster size and composition. The electrocatalytic activity of these electrodes for propanol oxidation was systematically evaluated using cyclic voltammetry (CV). Notably, PANI electrodes decorated with odd-numbered atomic-level Pt clusters exhibited higher peak oxidation currents compared to even-numbered clusters, revealing a unique even–odd effect. For atomic-level Pt-Au clusters, the catalytic activity was significantly influenced by the sequence of Pt and Au deposition, with PANI-Au₁Pt₃ achieving the highest catalytic activity (35.34 mA/cm²). Bi-metallic clusters consistently outperformed mono-metallic clusters, and clusters containing only one Pt atom demonstrated superior catalytic activity. These findings provide valuable insights into the design of high-performance catalytic electrodes by leveraging atomic-level control of the cluster size, composition, and deposition sequence, paving the way for advanced applications in electrochemical sensors. Full article

The importance and challenges of ethylene detection based on combustion-type low-cost commercial sensors for agricultural and industrial applications are well-established. This work summarizes the significant progress in ethylene detection based on an innovative Gas Metal Oxide Semiconductor (GMOS) sensor and a new catalytic composition of metallic nanoparticles. The paper presents a study on ethylene and ethanol sensing using a miniature catalytic sensor fabricated by Complementary Metal Oxide Semiconductor–Silicon-on-Insulator–Micro-Electro-Mechanical System (CMOS-SOI-MEMS) technology. The GMOS performance with bimetallic palladium–platinum (Pd-Pt) and monometallic palladium (Pd) and platinum (Pt) catalysts is compared. The synergetic effect of the Pd-Pt catalyst is observed, which is expressed in the shift of combustion reaction ignition to lower catalyst temperatures as well as increased sensitivity compared to monometallic components. The optimal catalysts and their temperature regimes for low and high ethylene concentrations are chosen, resulting in lower power consumption by the sensor. Full article

A novel amorphous Fe-doped manganese carbonate (a-FeMn-1) was synthesized via a facile co-precipitation method and evaluated as an efficient heterogeneous catalyst for the activation of peroxymonosulfate (PMS) in the degradation of Orange II. Among various Fe/Mn molar ratios, the 1:1 composition (a-FeMn-1) showed optimal catalytic activity, achieving 98% removal efficiency within 60 min under near-neutral pH conditions. Characterization results indicated that Fe doping effectively induced an amorphous structure and increased surface area and oxygen defects, promoting PMS activation. The system displayed broad pH applicability and resistance to Cl⁻ and natural organic matter, while degradation was inhibited by HCO₃⁻ and PO₄³⁻. EPR and quenching experiments confirmed that surface-bound sulfate radicals (SO₄^•−), hydroxyl radicals (^•OH), and singlet oxygen (¹O₂) were the primary reactive species. XPS analysis further revealed the redox cycling of Fe and Mn and the involvement of defect oxygen in the PMS activation process. The catalyst also demonstrated excellent reusability over five cycles without significant loss in efficiency. This work provides insights into the rational design of amorphous bimetallic materials for sulfate radical-based advanced oxidation processes. Full article

Electrocatalytic nitrate reduction to ammonia (ENRA) presents a promising strategy for simultaneous environmental remediation and sustainable ammonia synthesis. In this work, a Cu–Co bimetallic catalyst supported on functionalized reduced graphene oxide (RGO) was systematically designed to achieve efficient and selective ammonia production. Surface oxygen functional groups on graphene oxide (GO) were optimized through alkaline hydrothermal treatments, enhancing the anchoring capacity for metal active sites. Characterization indicated the successful formation of uniform Cu–Co bimetallic heterointerfaces comprising metallic and oxide phases, which significantly improved catalyst stability and performance. Among the studied compositions, Cu₆Co₄/RGO exhibited superior catalytic activity, achieving a remarkable ammonia selectivity of 99.86% and a Faradaic efficiency of 96.54% at −0.6 V (vs. RHE). Long-term electrocatalysis demonstrated excellent durability, with over 90% Faradaic efficiency maintained for ammonia production after 20 h of operation. In situ FTIR analysis revealed that introducing Co effectively promoted water dissociation, facilitating hydrogen generation (*H) and accelerating the transformation of nitrate intermediates. This work offers valuable mechanistic insights and paves the way for the design of highly efficient bimetallic electrocatalysts for nitrate reduction and ammonia electrosynthesis. Full article

To address the issues of poor Co²⁺ regeneration and limited interfacial electron transfer in heterogeneous catalytic systems, this study proposes the synthesis of highly efficient and stable Co₃O₄/ZnO composites through the pyrolysis–oxidation reaction of Co/Zn MOFs for the degradation of rhodamine B (RhB) using activated peroxymonosulfate (PMS). The results confirmed that the catalyst exhibited a high electron transfer capacity, and the synergistic effect between the bimetals enhanced the reversible redox cycle of Co³⁺/Co²⁺. Under optimal conditions, complete removal of RhB was achieved in just 6 min using the Co₃O₄/ZnO composite, which demonstrated excellent stability after five cycles. Furthermore, the catalyst exhibited a high degradation efficiency in real water samples with a total organic carbon (TOC) removal rate of approximately 65% after 60 min. The electrochemical measurements, identification of active species, and X-ray photoelectron spectroscopy (XPS) analysis revealed that non-radicals (¹O₂ and direct charge transfer) played a major role in the degradation of RhB. Finally, the potential mechanisms and degradation pathways for RhB degradation using this catalyst were systematically investigated. This study opens new avenues for the development of efficient and stable PMS catalysts, and provides insights into the preparation of other emerging metal oxides. Full article