Search Results (76)

Secondary caries and biofilm accumulation remain major causes of failure in provisional crowns and restorations, highlighting the need for multifunctional resin coatings with antibacterial and remineralizing capabilities. This study aimed to develop a novel bioactive and antibacterial resin-based surface coating incorporating 10% dimethylaminododecyl methacrylate (DMADDM), 20% nanoparticles of amorphous calcium phosphate (NACP), and/or 20% calcium fluoride nanoparticles (nCaF₂) within a urethane dimethacrylate/triethylene glycol divinylbenzyl ether (UDMA/TEG-DVBE) matrix. Coatings were evaluated for degree of conversion (DC), flow, shear bond strength, brushing wear resistance (10,000 cycles), and calcium (Ca), phosphate (PO₄), and fluoride (F) ion release up to 70 days. All groups achieved clinically acceptable polymerization, with the lowest DC at 50%. NACP-containing coatings significantly increased shear bond strength to 18.3 ± 2.8 MPa, representing a ~170% increase compared with the experimental control (6.8 ± 2.1 MPa) and exceeding the ISO 10477 minimum threshold of 5 MPa. After brushing simulation, experimental coatings demonstrated low wear depth (0.93–1.19 µm), which was ~40% lower than the commercial control (1.85 ± 0.40 µm). Sustained ion release was achieved for 70 days, with 20% NACP-formula releasing 1.22 mmol/L Ca and 0.90 mmol/L PO₄, while the dual NACP–nCaF₂ formulation provided simultaneous Ca (0.62 mmol/L) and F (0.33 mmol/L) release. The developed coatings demonstrated promising physicochemical properties, bonding performance, wear resistance, and sustained remineralizing ion release, supporting their potential application as therapeutic surface coatings for provisional restorations. Full article

Methacrylate-POSS (M-POSS) is a novel organic–inorganic additive shown to reinforce dental composites and reduce polymerization shrinkage. This study aimed to evaluate the influence of M-POSS addition (0.5, 2, 10, or 15 wt.%) on the mechanical properties of an experimental polymer matrix (bis-GMA/UDMA/TEGDMA/HEMA = 35/35/20/10 wt.%) and a dental resin composite (45 wt.% silanized silica as filler). Vickers hardness (HV), three-point bending strength (FS), diametral tensile strength (DTS), and shrinkage stress generated during polymerization were studied. The results show HV values between 16 and 18 compared to 15 ± 1 in the control group. Hardness in the control composite was 34 ± 4, and after modification, it showed similar or slightly lower values between 32 and 35. FS increased from 90 ± 4 MPa before modification to 100 ± 5 MPa for 2 wt.% M-POSS, and then decreased to 78 ± 5 MPa for materials containing 15 wt.% M-POSS. FS of composites were within the range of 61–77 MPa, with a similar tendency in variation to that of matrices. DTS values decreased after M-POSS addition, from 37 ± 4 MPa before modification to 31–33 MPa after modification. Flexural modulus decreases after modification, both for matrices and composites. The morphology of composites with >10 wt. % M-POSS showed visible surface irregularities. In conclusion, M-POSS affects matrix hardness, resulting in an increase in HV. The addition of M-POSS also increases FS values of the matrix, but only up to a certain concentration. However, the introduction of M-POSS does not significantly affect the HV or bending strength of the composites. Although DTS values decreased, this change was not statistically significant. Finally, contraction stress was significantly reduced for groups containing 2 wt.% and 10 wt.% M-POSS, representing an anticipated and promising improvement. Full article

We have investigated the major- and trace-element composition of hydrothermal pyrite, magnetite, and Ti-magnetite, and of the principal Cu-minerals chalcopyrite and chalcocite, to constrain ore-forming processes in the northeastern Saveh district (central Urumieh–Dokhtar magmatic arc, Iran). Our data provide new constraints on the magmatic–hydrothermal evolution and subsequent hydrothermal–supergene modification of the ore system. Ti-magnetites hosted in monzodioritic intrusions are enriched in Ti–V–Al, plot below the magnetite–ulvöspinel join and record high crystallization temperatures (<500 °C) under relatively low oxygen fugacity. By contrast, magnetite from silica-rich hydrothermal veins is Fe-rich with very low TiO₂; it formed at intermediate temperatures (~200–300 °C) under higher fO₂ and is markedly depleted in Ti and V compared with the intrusive oxides. Textures and oxide systematics (Al + Mn vs. Ti + V; V/Ti–Fe) document repeated hydrothermal pulses, Fe²⁺ leaching and element redistribution during cooling and fluid–rock interaction. Geochemical trends indicate progressive evolution from a magmatic fluid to later meteoric water overprint, with increasing As contents reflecting cooling and mixing with meteoric waters. Vertical elemental zoning suggests that most samples represent mid- to deep-level sections of the epithermal system. Elevated Cu contents (up to 0.95 wt.%) highlight pyrite as a significant Cu host. Co/Ni ratios between 1 and 10 further corroborate a magmatic–hydrothermal origin. Chalcopyrite is the principal economic Cu carrier at Northeast Saveh. Replacement follows a temperature- and fluid-controlled pathway (chalcopyrite → covellite → chalcocite). At lower temperatures (<~200 °C) replacement proceeds more slowly, producing chalcocite/digenite under prolonged reaction conditions. Chalcocite commonly occurs as thin replacement rims and fracture fills that concentrate remobilized copper. Collectively, the investigated oxide and sulfide proxies provide robust discriminants for separating magmatic versus hydrothermal domains and for vectoring toward higher-temperature feeders and zones of remobilized copper. Full article

The research hypothesis was that adjusting the content of the quaternary ammonium urethane dimethacrylate monomer bearing an N-dodecyl substituent (QAUDMA-12) would yield dental matrices with high antimicrobial activity, good biocompatibility, and favorable physicochemical properties. The research hypothesis was verified for six Bis-GMA, TEGDMA, and UDMA copolymers containing from 2.5 to 40 wt.% QAUDMA-12 by determining their degree of conversion, hardness, flexural properties, water behavior, antimicrobial activity against Staphylococcus aureus, Staphylococcus epidermidis, Escherichia coli, Candida albicans, and cytotoxicity towards L929 mouse fibroblast cells. The research hypothesis was confirmed. Copolymers containing less than 30 wt.% QAUDMA-12 exhibited favorable polymerization efficiency, water sorption and solubility, and mechanical properties comparable to those of conventional Bis-GMA/TEGDMA systems. At the same time, they showed no cytotoxic effects toward mouse fibroblast cells. The results of antimicrobial tests show that the minimum QAUDMA-12 concentration providing sufficient antimicrobial activity was 20 wt.%. Therefore, it can be concluded that the 20 wt.% concentration of QAUDMA-12 makes it possible to obtain dental matrices that are non-toxic, exhibit antimicrobial activity, and possess the desired physico-mechanical performance. Full article

Occlusal splints are a type of intraoral appliance that are widely used for the management of temporomandibular disorders and bruxism, yet limited evidence exists regarding the comparative effects of combined aging on conventional and digitally manufactured materials. This in vitro study evaluated the influence of thermal and mechanical aging on the flexural properties of three materials commonly used for the manufacturing of occlusal devices: self-curing poly(methyl methacrylate) (PMMA, control), light-cured urethane dimethacrylate (UDMA)-based resin, and stereolithography (SLA)-printed photopolymer. Seventy-two standardized specimens (n = 24 per material; 64 × 10 × 3.3 mm) were fabricated, then randomly allocated to three groups (n = 8): control, thermocycling (10,000 cycles, 5 °C/55 °C), and combined thermocycling with mechanical loading (1000 cycles). Flexural strength and modulus were determined by three-point bending tests and analyzed using a two-way analysis of variance (ANOVA) with Tukey’s post hoc test (α = 0.05). Thermocycling significantly reduced flexural strength in PMMA (65.19 ± 6.68 to 57.94 ± 7.15 MPa) and SLA (67.67 ± 1.54 to 59.37 ± 8.80 MPa) groups (p < 0.05), while UDMA group (45.489 ± 3.905 to 43.123 ± 4.367 MPa) demonstrated no significant changes (p ≥ 0.05). UDMA exhibited substantially and significantly lower flexural properties compared to PMMA and SLA across all conditions (p < 0.0001). Thermal aging slightly compromises the mechanical properties of PMMA and SLA-printed materials, whereas UDMA-based resins exhibit good aging resistance but considerably lower initial values. While UDMA-based resin showed superior aging resistance, its lower baseline mechanical properties may limit its application in high-stress clinical scenarios compared to PMMA and SLA-printed materials. Material selection should consider both initial properties and long-term environmental changes. Full article

Background: White spot lesions (WSLs) are characterized by enamel demineralization. Minimally invasive treatments using infiltrating resins, such as the commercially available Icon^®, are recommended. The need for such treatments justifies ongoing research into developing materials that can address existing limitations regarding strength, durability, and biocompatibility. Objectives: This study aimed to synthesize and characterize four novel nanobiomaterials by evaluating their physicochemical properties and biocompatibility compared to the commercial material Icon^®. Materials and methods: The recipes for the experimental nanobiomaterials NB3, NB6, NB3F, and NB6F contain varying proportions of TEGDMA, UDMA, HEMA, Bis-GMA, and HAF-BaF2 glass. Mechanical and physicochemical characteristics were evaluated, such as flexural strength, measured using the three-point test; water absorption and solubility; fluoride release; polymerization conversion; and residual monomers, assessed using High-Performance Liquid Chromatography (HPLC). In vitro cell viability was assessed via colorimetry using human dysplastic oral keratinocytes (DOKs). Results: NB6 and NB6F demonstrated the greatest polymerization potential. NB3 exhibited the lowest water absorption and solubility due to its hydrophobic nature. Additionally, the inclusion of UDMA enhanced the strength and elasticity of NB3 when compared to NB6. Among the samples with fluoride additives (NB3F and NB6F), the highest fluoride release on day 7 occurred with the material lacking UDMA. In contrast, the NB3F sample containing UDMA released the least amount of fluoride on the same day. In quantitative terms, NB3 and NB6F exhibited the lowest levels of residual monomers, whereas NB6 showed the highest levels. Both NB3 and NB6 were significantly better tolerated by the cells, showing higher cell viability compared to the commercial material Icon^®. Conclusions: The materials’ mechanical and physicochemical properties varied with component proportions, enabling identification of a suitable formulation for targeted clinical applications. Biocompatibility tests showed that the experimental NB3 and NB6 were better tolerated than Icon^®. Furthermore, the incorporation of filler particles improved the mechanical strength of the experimental nanobiomaterials. Full article

Dental composites are commonly used for the restoration of hard tooth tissues, but their low fracture toughness may limit their lifespan. In this study, the effect of liquid rubber modification on the mechanical properties and fracture mechanisms of two types of dental composites, flow and classic, was evaluated. The study used experimental composites containing a mixture of dimethacrylate resins: BisGMA (20% by weight), BisEMA (30% by weight), UDMA (30% by weight), and TEGDMA (20% by weight). Composites were reinforced with Al-Ba-B-Si glass, Ba-Al-B-F-Si glass with particle sizes of 0.7 and 2 μm respectively, as well as pyrogenic silica (20 nm). The inorganic phase was introduced in an amount of 50% vol. for flow material and 80% vol. for classic composite. As a modifier, Hypro 2000X168LC VTB liquid rubber (Huntsman International LLC, USA) was used in an amount of 5% by weight relative to the matrix. The flexural strength, Young’s modulus, and fracture toughness were evaluated. Numerical FEM analysis allowed for the evaluation of stress distribution in the filling area. The results confirmed that the modification of composites with liquid rubber contributes to an increase in fracture toughness. For the flow-type material, the fracture toughness increased from 1.04 to 1.13 MPa·m^1/2. At the same time, a decrease in flexural strength from 71.90 MPa to 61.48 MPa and in Young’s modulus from 2.98 GPa to 2.53 GPa. In the case of the classical composite, the modification with liquid rubber also improved the resistance to fracture, increasing it from 1.97 to 2.18 MPa·m^1/2 while the flexural strength decreased from 102.30 MPa to 90.96 MPa, and the modulus dropped from 7.33 GPa to 6.16 GPa. FEA analysis confirmed that modified composites exhibit a more favorable stress distribution with lower tensile stress levels (approximately 20 MPa in contrast to 25 MPa for the classic composite). Mechanisms of fracture and strengthening were also identified. The main fracture mechanism was intermolecular cracking with crack deflections. Modification with liquid rubber resulted in the formation of elastic bridges and plastic shear zones at the front of the crack. Full article

Background: Clear aligners have become a common alternative to fixed appliances for tooth movement, and thermoplastic retainers hold the outcome. The prolonged intraoral contact of these devices has made the materials a focus of biocompatibility research. Objectives: This paper aims to summarize laboratory evidence on the biocompatibility of clear aligners and thermoplastic retainers. Materials included thermoformed polyethylene terephthalate glycol-modified (PETG), multilayer polyurethane, and directly printed resins. Primary outcomes were cytotoxicity, endocrine activity, and chemical or particle release. Methods: We systematically searched PubMed, the Cochrane Library, and Google Scholar through 31 May 2025, and we followed the PRISMA 2020 statement (Preferred Reporting Items for Systematic Reviews and Meta-Analyses). We applied predefined eligibility criteria. Two reviewers screened records and extracted data in duplicate, including study design, extraction conditions, surface-area-to-volume ratio (SA/V), cell models, endpoints, and analytical sensitivity as the limit of detection (LOD) and limit of quantification (LOQ). We assessed the risk of bias across seven domains and graded certainty by outcome. We did not register a protocol prospectively. Results: Seventeen studies met the inclusion criteria. Materials spanned multilayer polyurethanes (SmartTrack, Clarity), PETG sheets (Essix ACE, Duran), and directly printed resins (Graphy TC-85DAC); a subset tested zinc-oxide (ZnO) nanoparticle coatings. Typical extractions immersed 0.1–1 g of material in cell-culture medium or artificial saliva at 37 °C for 24 h to 30 days. Cell viability usually remained ≥80%. Mild cytotoxicity (about 60–70% viability) appeared with harsher extractions, extended soaks, or an inadequate post-curing of printed parts. The estrogen-sensitive proliferation assay (E-Screen) returned negative results. In saliva-like media, bisphenol A (BPA) and related leachables were undetectable or in the low ng/mL range. In printed resins, urethane dimethacrylate (UDMA) sometimes appeared in water extracts, and amounts varied with curing quality. Evidence for chemical leaching and endocrine outcomes is sparse. We found no eligible in vitro study that quantified particle or microplastic release while also measuring a biological endpoint; we discuss particle findings from mechanical wear simulations only as the external context. Limitations: The evidence base is limited to in vitro studies. Many reports incompletely described extraction ratios and processing parameters. Risk of bias and certainty: Most studies used appropriate cell models and controls, but the reporting of surface-area-to-volume ratios, LOD/LOQ, and detailed post-processing parameters was often incomplete. Sample sizes were small, and dynamic wear or enzymatic conditions were uncommon. The overall risk of bias was moderate, and the certainty of evidence was low to moderate due to heterogeneity and in vitro indirectness. Conclusions: Under standard laboratory conditions, clear aligners and thermoplastic retainers show a favorable biocompatibility profile. For printed resins, outcomes depend mainly on processing quality, especially thorough washing and appropriate light-curing parameters. To improve comparability and support clinical translation, we recommend harmonized test protocols, transparent reporting, interlaboratory ring trials, and targeted clinical biomonitoring. Full article

This study aimed to assess how different resin matrix formulations affect the fatigue resistance of resin dental composites. Model dental composites were formulated using six distinct monomer mixtures: two Bis-GMA (bisphenol A-glycidyl methacrylate):TEGDMA (triethylene glycol dimethacrylate) (60:40 and 80:20 mole%), two UDMA (urethane dimethacrylate):TEGDMA (60:40 and 80:20 mole%), one Bis-GMA:UDMA:TEGDMA (35:35:30 mole%), and one Fit852:UDMA:TEGDMA (35:35:30 mole%). Cyclic fatigue resistance (CFR) of the resin composites was measured in a biaxial test mode using staircase analysis. Additional evaluations included biaxial flexural strength (BFS), degree of conversion (DC), water sorption (WS), and viscoelastic properties of the unfilled resins, such as the storage modulus (E′), loss modulus (E″), tan δ (E″/E′), and stiffness (k′). Data were subjected to one-way ANOVA with Tukey post hoc analyses. Pearson correlation and stepwise regression analyses were conducted to examine the relationships among variables. The UT6040 model composite exhibited the highest CFR (82.61 ± 8.83 MPa), significantly outperforming other formulations. Tan δ of the resin matrix showed the strongest correlation with CFR (r = 0.974), and was also shown to be the most influential predictor for the CFR of the particulate composites. The composition of the resin matrix has a significant impact on the CFR of dental composites. Among the properties evaluated, the viscoelastic parameter tan δ emerged as a strong and reliable predictor of CFR, emphasizing the importance of targeting viscoelastic behavior in the design of dental composite formulations. Full article

Background: This study aimed to assess the impact of methacrylate-functionalized polyhedral oligomeric silsesquioxanes dispersed in nanosilica (MA/Ns-POSS) on the mechanical properties of light-curable dental resins and composites. The primary goal was to evaluate how different concentrations of MA/Ns-POSS (0.5–20 wt.%) affect the hardness, flexural strength, modulus, diametral tensile strength, polymerization shrinkage stress, and degree of conversion of these materials. Methods: A mixture of Bis-GMA, UDMA, TEGDMA, HEMA, and camphorquinone, with a tertiary amine as the photoinitiator, was used to create resin and composite samples, incorporating 45 wt.% silanized silica for the composites. Hardness (Vickers method, HV), flexural strength (FS), and flexural modulus (E_f) were assessed using three-point bending tests, while diametral tensile strength (DTS) polymerization shrinkage stresses (PSS), and degree of conversion (DC) analysis were analyzed for the composites. Results: The results showed that resins with 10 wt.% MA/Ns-POSS exhibited the highest E_f and FS values. Composite hardness peaked at 20 wt.% MA/Ns-POSS, while DTS increased up to 2.5 wt.% MA/Ns-POSS but declined at higher concentrations. PSS values decreased with increasing MA/Ns-POSS concentration, with the lowest values recorded at 15–20 wt.%. DC analysis also showed substantial improvement for 15–20 wt.% Conclusion: Incorporating MA/Ns-POSS improves the mechanical properties of both resins and composites, with 20 wt.% showing the best results. Further studies are needed to explore the influence of higher additive concentrations. Full article

This study evaluated the effects of conventional cigarette smoke compared to aerosol from a heat-non-burn tobacco product on the color stability of two UDMA-based dental composite resins, namely a monochromatic (Omnichroma) and a polychromatic (Vittra APS) resin. Twenty disc-shaped specimens were prepared, divided into two groups of ten, and exposed to 105 cigarettes or 105 aerosol tobacco sticks via a custom-made smoking chamber. Puff duration was 2 s, with a 60 s interval between puffs in which smoke saturated the chamber for 30 s; then, clean air was introduced into the chamber for 30 s. Six puffs and six intervals were simulated. Color parameters were measured before and after exposure and following brushing of each specimen with 15 strokes. Color differences were determined based on the CIEDE2000 formula. Significant color change was found in all specimens exposed to cigarette and tobacco aerosol. The highest color-change mean value was obtained from composite resin exposed to cigarette smoke. Although both cigarette and thermal heating systems cause discoloration, the aerosol causes reduced composite resin discoloration, which compromises aesthetics and increases patient dissatisfaction, impacting the overall dental care. Color stability is the hallmark of success, as it is the main reason for replacing dental restorations. Full article

A method to prepare free-standing, few-micron-thick films from a dental photopolymer resin, namely UDMA-TEGDMA in a 3:1 weight ratio, doped with gold nanorods, is presented. The method is based on a sandwich structure consisting of a 4 μm thick PVA sacrificial layer, the Au-nanorod/UDMA-TEGDMA nanocomposite layer, and glycerol, all spin-coated sequentially onto a glass slide. Glycerol serves as a cover layer to shut out oxygen during photopolymerization, while the water-soluble PVA enables the subsequent detachment of the nanocomposite film by simple immersion into a liquid bath. Layer thicknesses were controlled by profilometry, while the presence of homogeneously dispersed gold nanorods was confirmed by optical spectroscopy and dark-field optical microscopy. A total of five similar spin-coating scenarios were tested, out of which two approaches produced positive results, with final nanocomposite layer thicknesses in the 2.5–4 μm range, which is smaller than the usual thickness of the oxygen inhibition layer (OIL) commonly present in these types of resins. Optimization of these technological processes and parameters to control film thickness and consistency is discussed in detail. Full article

Resin-based composites are common and widely used materials in dentistry in direct and indirect applications. Their mechanical properties depend on the composition and homogeneity of the resulting structure. This study aims to optimize the mixing process to obtain the most homogeneous mixture possible, which will allow for the better mechanical properties of the composite. A mixture of bis-GMA/UDMA/HEMA/TEGDMA monomers forming a polymer matrix was filled with silanized silica (45 wt%) using different mixing methods. This study analyzed five manufacturing methods—hand mixing (agate mortar), mixing in a centrifugal Hauschild SpeedMixer, and the hybrid method—combined with the abovementioned methods. The effect of the mixing method on the Vickers hardness (HV), flexural strength (FS), compressive strength (CS), and diametral tensile strength (DTS) of the produced composites was investigated, and the stresses generated during composite polymerization were determined. Mechanically prepared composites have the highest flexural strength and hardness. The lowest shrinkage stress was achieved by the composite, which was prepared partially manually. The results showed that the mixing method affects the morphology of the filler and, hence, the strength properties of the resulting material. Full article

To create an orthodontic bracket material combining the favourable properties of ceramic and polymer while minimising their limitations, graded porous ceramic scaffolds were created using unidirectional gelation-freeze casting, following which the pores were infiltrated with polymer. Two processing parameters were investigated: (1) sedimentation times of 0, 8, and 24 h, with ceramic solid loading of 20 vol.% and 2.5 wt.% gelatine concentration, and (2) ceramic solid loadings of 15, 20, and 25 vol.% with a fixed 2.5 wt.% gelatine concentration and an 8 h sedimentation time. The graded ceramic structures demonstrated porosity gradients ranging from 9.86 to 63.84 vol.%, except those with 25 vol.% ceramic solid loading at 8 h sedimentation. The Al₂O₃-UDMA/TEGDMA composites had compressive strengths of 60.25 to 120.92 MPa, modulus of elasticity of 19.84 to 35.29 GPa, and fracture toughness of 0.78 to 1.78 MPa·m^1/2. The values observed were between those of dense ceramic and pure polymer. Statistical analysis was conducted using Excel^® 2019 (Microsoft^®, Washington, DC, USA). Means, standard deviations, and 95% confidence intervals (CI) were calculated at a significance level of α = 0.05, alongside polynomial regression to evaluate relationships between variables. Composites with 20 vol.% ceramic solid loading at 8 h sedimentation displayed promising potential for further clinical validation. Full article

Cenozoic plutonic rocks in northeast Saveh, part of the central Urumieh–Dokhtar Magmatic Arc (UDMA) in Iran, comprise monzonite, monzodiorite, gabbro, and gabbrodiorite. Geochemical, zircon U-Pb geochronology, and Hf isotopic data reveal that these plutonic rocks belong to a medium-K calc-alkaline, metaluminous series with arc-related signatures. Zircon U-Pb ages (ca. 60 to 3 Ma) indicate prolonged magmatic evolution from the Middle Paleocene to the Middle Pliocene. Contrary to earlier reports of a 15 Ma period of reduced magmatic activity (ca. 72–57 Ma), our data indicate a shorter interval (ca. 10–12 Ma) during which magmatic activity decreased significantly. Key magmatic pulses occurred during the Late Eocene (ca. 40–47 Ma), Early Miocene (ca. 23–18 Ma), and Late Miocene–Pliocene (ca. 11–5.2 Ma), with geochemical data indicating a subduction-related origin. The most recent magmatic pulses in the central UDMA, potentially extending across the entire UDMA, are dated between 5 and 2.5 Ma, identified in a cluster of zircons from gabbroic rocks, which could correspond to the concluding stages of slab steepening related to continental subduction. Zircon εHf(t) values (−11.43 to 12.5) and geochemical data suggest fractional crystallization, crustal assimilation, and mantle-derived melts. The clinopyroxene crystallization temperatures (1150–1200 °C) and supporting geochemical data imply that magma was produced in a metasomatized spinel–lherzolite mantle at depths <80 km. This generation is associated with asthenospheric upwelling and slab rollback, which, in turn, triggered the partial melting of the lithosphere and fueled the region’s magmatic activity. Full article