Search Results (520)

This study developed a new magnetic adsorbent from waste coconut shells using high-temperature carbonization, EDTA-2Na chelation, and Fe₃O₄ magnetic loading. Response surface methodology optimized the preparation conditions to a mass ratio of activated carbon: EDTA-2Na:Fe₃O₄ = 2:0.6:0.2. Characterization (SEM, XRD, FT-IR, and EDS) showed that EDTA-2Na increased the surface carboxyl and amino group density, while Fe₃O₄ loading (Fe concentration 6.83%) provided superior magnetic separation performance. The optimal adsorption conditions of Cu²⁺ by EDTA-2Na-Fe₃O₄-activated carbon composite material are as follows: when pH = 5.0 and the initial concentration is 180 mg/L, the equilibrium adsorption capacity reaches 174.96 mg/g, and the removal rate reaches 97.2%. The optimal adsorption conditions for Pb²⁺ are as follows: when pH = 6.0 and the initial concentration is 160 mg/L, the equilibrium adsorption capacity reaches 157.60 mg/g, and the removal rate reaches 98.5%. The optimal adsorption conditions for Cd²⁺ are pH = 8.0 and an initial concentration of 20 mg/L. The equilibrium adsorption capacity reaches 18.76 mg/g, and the removal rate reaches 93.8%. The adsorption followed the pseudo-second-order kinetics (R² > 0.95) and Langmuir/Freundlich isotherm models, indicating chemisorption dominance. Desorption experiments using 0.1 mol/L HCl and EDTA-2Na achieved efficient desorption (>85%), and the material retained over 80% of its adsorption capacity after five cycles. This cost-effective and sustainable adsorbent offers a promising solution for heavy metal wastewater treatment. Full article

Sulfur fumigation (SF), acid dipping (HCl treatment, HAT), and their combination (SF+HAT) are common methods for long-term preservation and color protection of litchi. However, their effects on the metabolic profile of the litchi pericarp have not been investigated. SF resulted in a yellowish-green pericarp by up-regulating lightness (L*), b*, C*, and h° but down-regulating total anthocyanin content (TAC) and a*, while HAT resulted in a reddish coloration by up-regulating a*, b*, and C* but down-regulating L*, h°, and TAC. SF+HAT recovered reddish color with similar L*, C* to SF but a*, b*, h°, and TAC between SF and HAT. Differential accumulated metabolites (DAMs) detected in HAT (vs. control) were more than those in SF (vs. control), but similar to those in SF+HAT (vs. control). SF specifically down-regulated the content of cyanidin-3-O-rutinoside, sinapinaldehyde, salicylic acid, and tyrosol, but up-regulated 6 flavonoids (luteolin, kaempferol-3-O-(6″-malonyl)galactoside, hesperetin-7-O-glucoside, etc.). Five pathways (biosynthesis of phenylpropanoids, flavonoid biosynthesis, biosynthesis of secondary metabolites, glutathione metabolism, and cysteine and methionine metabolism) were commonly enriched among the three treatments, which significantly up-regulated sulfur-containing metabolites (mainly glutathione, methionine, and homocystine) and down-regulated substrates for browning (mainly procyanidin B2, C1, and coniferyl alcohol). These results provide metabolic evidence for the effect of three treatments on coloration and storability of litchi. Full article

Low-concentration N₂O (≤5%) emissions from agricultural fields and waste treatment facilities in China reach 7.333 × 10⁵ t annually, making them a significant but inadequately controlled contributor to global warming. Agricultural wastes were selected as precursors to prepare biochar, including pecan shell (SH), poplar sawdust (JM), wheat straw (XM), and corn straw (YM), which were subsequently acid-modified with 0.1 mol L⁻¹ HCl. The objectives were (i) to quantify the enhancement in N₂O capture achievable by acid treatment, (ii) to elucidate the underlying chemisorption mechanism, and (iii) to identify the most efficient feedstock for practical deployment. Acid modification increased the oxygen content, specific surface area, and the number of hydroxyl and carboxyl groups on the biochar surface. Both modified and unmodified biochar followed the pseudo-second-order kinetic model (R² ≥ 0.960), indicating chemisorption-dominated processes. The adsorption performance ranked as XM > JM > SH > YM, with XM exhibiting the highest adsorption capacity (26.000 mol/kg unmodified, 43.088 mol/kg modified, 65.72% increase). The Langmuir model provided a better fit for N₂O adsorption, suggesting dynamic multilayer heterogeneous adsorption. The findings demonstrate that acid-modified biochar derived from agricultural waste is a scalable, economical, and environmentally friendly adsorbent for mitigating low-concentration N₂O emissions. Full article

Background/Objectives: Gallic acid, a natural phenolic compound, was used as a crosslinking agent to achieve protein–polyphenol conjugation under alkaline conditions, presenting an innovative approach to stabilize gelatin. Methods: The formulated inks were evaluated for their rheological properties and 3D printing performance. Once the scaffolds were printed, physicochemical properties were assessed by color changes and FTIR. Additionally, three different post-processing methods were studied to avoid toxicity: incubation in PBS, incubation in NaOH followed by PBS neutralization, and incubation in HCl followed by PBS neutralization. Results: The inks exhibited shear-thinning behavior with self-supporting capacity after extrusion, indicating their suitability for use as inks in 3D printing. After printing, changes in color and in the amide I band/amide II band ratio were observed due to alkaline oxidation, confirming the gelatin crosslinking. Among the tested treatments, incubation in PBS or NaOH followed by neutralizing with PBS proved to be the most suitable for obtaining cytocompatible scaffolds. The mechanical properties demonstrated the suitability of the proposed crosslinking systems for creating scaffolds. Conclusions: This strategy confirms that gallic acid-mediated crosslinking under alkaline conditions enables the fabrication of cytocompatible and mechanically stable gelatin-based scaffolds, making them suitable for tissue engineering. Full article

Among the strategic materials considered by the EU, tungsten is included; thus, investigations about the recovery of this metal both from natural and recyclable sources are of interest. In this work, we presented an investigation about the recovery of tungsten based on the treatment of three tungsten-bearing concentrates: scheelite (29% W), wolframite (50% W), and mixed scheelite–wolframite (29% W). All of these come from a cassiterite ore of Spanish origin. The characteristics of each concentrate pave the procedure to be followed in each case. In the case of the wolframite concentrate, the best results were derived from the leaching of the ore with NaOH solutions, whereas the treatment of the scheelite concentrate benefits from an acidic (HCl) leaching. The attack of the mixed concentrate is only possible by a previous roasting step (sodium carbonate and 700–800 °C) followed by a leaching step with water. In the acidic leaching, tungstic acid (H₂WO₄) was obtained, and the alkaline–water leaching produces Na₂WO₄ solutions from which pure synthesized scheelite is precipitated. Full article

Poly(acrylic acid) (PAA) and hydroxypropylcellulose (HPC) hydrogels were synthesized in the absence of a crosslinker. Chemical crosslinking between PAA and HPC was demonstrated through free radical polymerization by a precipitation reaction in acetone as the solvent. These hydrogels exhibited smaller swelling ratios (1 to 5 g H₂O/g) than homo PAA hydrogels synthesized in water as the solvent. They were swollen in a 0.1 M NaOH solution and subsequently used to remove Ni²⁺ ions from aqueous solutions with concentrations ranging from 1000 to 4000 ppm. The absorption capacity of these hydrogels ranged from 91 to 340 mg of Ni²⁺/g in a rapid 1 h process, and from 122 to 435 mg of Ni²⁺/g in a 24 h process, demonstrating an improvement in Ni²⁺ absorption compared to previously reported hydrogels. The colored 1000 and 2000 ppm Ni²⁺ solutions became clear after treatment, while the PAA-HPC hydrogels turned green due to the uptake of Ni²⁺ ions, which were partially chelated by carboxylate groups as nickel polyacrylate and partially precipitated as Ni(OH)₂, resulting in an average absorption efficiency of 80%. The hydrogel was able to release the absorbed Ni²⁺ upon immersion in an HCl solution, with an average release percentage of 76.4%, indicating its potential for reuse. These findings support the use of PAA-HPC hydrogels for cleaning Ni²⁺-polluted water. The cost of producing 1 g of these hydrogels in laboratory conditions is approximately 0.2 USD. Full article

Hypochlorous acid (HClO) serves as a biological mediator and is widely utilized as a disinfectant in food processing and water treatment. However, excessive HClO residues in food and environmental water raise concerns due to the potential formation of carcinogenic chlorinated byproducts and disinfection byproducts (DBPs). Despite its importance, traditional methods for HClO detection often involve complex sample preparation, sophisticated instrumentation, and skilled operators. Herein, we report an aggregation-induced emission (AIE) small molecule fluorescent probe (NYV) that integrates colorimetric and ratiometric fluorescence responses for the detection of HClO. This probe exhibits high sensitivity, with a detection limit of 0.35 $\mathsf{\mu }$M, a rapid response time of 1 min, and a wide linear range (0–142.5 $\mathsf{\mu }$M), along with anti-interference capabilities, making it suitable for real-time monitoring. Furthermore, we have developed a portable solid-state sensor based on probe NYV for the rapid visual detection of HClO. The potential applications of this probe in real sample analysis and bioimaging experiments are demonstrated. Our findings contribute to the development of innovative fluorescent probes for HClO detection, with broad applications in food safety, environmental monitoring, and biomedical research on oxidative stress and ferroptosis. Full article

The disposal of olive mill wastewater (OMWW) poses significant environmental challenges due to its high content of phytotoxic and pollutant compounds. This study aims to explore the chemical composition of OMWW derived from various olive varieties (Buža, Buža puntoža, Istarska bjelica, Leccino, and Rosinjola) and assess its antifungal potential against phytopathogenic fungi from the Botryosphaeriaceae family. OMWW samples were analyzed for their physicochemical properties, phenolic composition via LC-MS/MS, and antifungal activity against Botryosphaeria dothidea (Moug. ex Fr.) Ces. & De Not., Diplodia mutila (Fr.) Fr., D. seriata De Not., Dothiorella iberica A.J.L. Phillips, J. Luque & A. Alves, Do. sarmentorum (Fr.) A.J.L. Phillips, Alves & Luque, and Neofusicoccum parvum (Pennycook & Samuels) Crous, Slippers & A.J.L. Phillips. Antifungal efficacy was tested at varying concentrations, alongside the phenolic compounds hydroxytyrosol and vanillic acid. Antifungal activity varied across fungal species and OMWW concentrations. Lower OMWW concentrations inhibited mycelial growth in some pathogens, while higher concentrations often had a stimulatory effect. Among the OMWW treatments, Leccino and Buža showed the most significant antifungal activity against species from the Botryosphaeriaceae family. The results demonstrated significant variability in OMWW composition, with Istarska bjelica exhibiting the highest concentrations of phenolic compounds, sugars, dry matter, and carbon and nitrogen content. The results also highlight the impact of acidification on the phenolic profile of OMWW. Treatment with HCl significantly altered the concentration of individual phenolic compounds, either enhancing their release or contributing to their degradation. Among the two compounds, vanillic acid showed greater efficacy than hydroxytyrosol. In addition, microorganisms isolated from OMWW, including Bacillus velezensis Ruiz-Garcia et al., Rhodotorula mucilaginosa (A. Jörg.) F.C. Harrison, Nakazawaea molendiniolei (N. Cadez, B. Turchetti & G. Peter) C. P. Kurtzman & C. J. Robnett, and Penicillium crustosum Thom, demonstrated antagonistic potential against fungal pathogens, with B. velezensis showing the strongest inhibitory effect. The greatest antagonistic effect against fungi was observed with the species Do. Iberica. The findings highlight the potential of OMWW as a sustainable alternative to chemical fungicides, simultaneously contributing to the management of waste and protection of plants through circular economy principles. Full article

Nanoscale zinc sulfide (ZnS) powders have attracted considerable interest due to their unique properties and diverse applications in various fields, including wastewater treatment, optics, electronics, photocatalysis, and solar systems. In this study, nano-powder ZnS was chemically synthetized starting from Zn powder, diluted HCl, and laboratory-prepared Na2S. The obtained ZnS was studied using an SEM coupled with EDS, XRD analysis, UV–Visible spectroscopy, and FTIR techniques. The XRD results showed that the synthesized nanoscale ZnS powder was approximately 2.26 nm. Meanwhile, the EDS and XRD patterns confirmed the high purity of the obtained ZnS powder. In addition, the ZnS powder was compacted and sintered in an argon atmosphere at 400 °C for 8 h to prepare the required pellets for thin-film deposition via E-beam evaporation. The microscopic structure of the sintered pellets was investigated using the SEM/EDS. Furthermore, the optical properties of the deposited thin films were studied using UV–Visible spectroscopy in the wavelength range of 190–1100 nm and the FTIR technique. The bandgap energies of the deposited thin films with thicknesses of 111 nm and 40 nm were determined to be around 4.72 eV and 5.82 eV, respectively. This article offers a facile production route of high-purity ZnS powder, which can be compacted and sintered as a suitable source for thin-film deposition. Full article

Background: Traditional sandblasted large-grit acid-etched (SLA) surface treatments frequently utilize alumina (Al₂O₃) blasting, which may leave residual particles embedded in implant surfaces, potentially compromising biocompatibility and osseointegration. This study investigates a contamination-free alternative: titanium dioxide particle (TiO₂) blasting followed by hydrochloric acid (HCl) etching, aimed at generating a cleaner, hierarchical micro–nano-textured surface. Methods: Grade IV titanium disks were treated either with TiO₂ sandblasting alone or with an additional HCl etching step. Surfaces were analyzed via atomic force microscopy (AFM), scanning electron microscopy (SEM), contact angle measurements, and profilometry. hFOB osteoblasts were cultured to assess adhesion, proliferation, metabolic activity, and morphology. Results: The combination treatment produced a more homogeneous micro–nano structure with significantly increased roughness and a cleaner surface chemistry. Osteoblast proliferation and metabolic activity were notably improved in the TiO₂ and HCl group. SEM imaging showed a more organized cytoskeletal structure and pronounced filopodia at 72 h. Conclusions: Titanium blasting combined with HCl etching yields a cost-effective, contamination-free surface modification with promising early-stage cellular responses. This approach represents a safer and effective alternative to conventional SLA treatment. Full article

This work concerns the preparation of Pt/AC catalysts (Pt supported on activated carbon) and their application to the synthesis of hydrocarbon biofuels through the HEFA (hydroprocessing of esters and fatty acids) route. The key motivation for the work was that catalysts based on sulfided Mo supported on γ-Al₂O₃, traditionally employed in the hydroprocessing of petroleum derivatives, (i) are unstable in the HDO (hydrodeoxygenation) of biomass-derived feedstocks and (ii) can contaminate the resulting biofuels with sulfur. In this context, a systematic study on the effects of preparation conditions on the properties of the resulting Pt/AC catalysts and their performance in HEFA was carried out for the first time. Efficient catalysts were obtained, which led to the complete deoxygenation of lauric acid and coconut oil, yielding products composed primarily of n-alkanes. The highest HDO activity was verified for the catalyst prepared using as a support an AC previously subjected to thermal treatment up to 800 °C in a H₂ atmosphere (which removed most of the surface acidic oxygenated groups), depositing Pt over the surface of this support via wet impregnation using a H₂PtCl₆ solution acidified with HCl. The obtained results showed the great potential of the Pt/AC catalysts for the production of hydrocarbon biofuels through the HEFA route. Full article

This study explored the production and activation of biochar from rice straw residue for dye adsorption applications. Rice straw, a widely available but underutilized biomass, was processed to isolate lignin and generate biochar through pyrolysis at 450 °C and 550 °C. Activation using chemical agents (e.g., KOH and NaOH) was performed to enhance surface area and porosity. Among the tested conditions, KOH activation at a char-to-agent ratio of 1:3 produced activated carbon at 800 °C with the highest BET surface area (835.2 m²/g), and high fixed carbon (44.4%) after HCl washing. Thermogravimetric analysis was used to investigate pyrolysis kinetics, with activation energies determined using the Kissinger, Flynn–Wall–Ozawa, and Kissinger–Akahira–Sunose models. The brown solid showed a higher activation energy (264 kJ/mol) compared to isolated lignin (194 kJ/mol), indicating that more energy is required for decomposition. The AC was evaluated for the adsorption of methylene blue (MB) and methyl orange (MO) from aqueous solutions. Both dyes followed the Langmuir isotherm model, indicating that monolayer adsorption occurred. The maximum adsorption capacities reached 222 mg/g for MB and 244 mg/g for MO at 303 K, with higher values at elevated temperatures. Adsorption followed a pseudo-second-order kinetic model and was governed by a physisorption mechanism, as supported by thermodynamic analysis (ΔH < 20 kJ/mol and E_a < 40 kJ/mol). These findings demonstrate that KOH-activated biochar from rice straw residue is a high-performance, low-cost adsorbent for dye removal, contributing to sustainable biomass utilization and wastewater treatment. Full article

Background/Objectives: Currently there are very few effective oral antileishmanial treatments. In this study we evaluated a new bis(pyridine-2-carboxamidine) antileishmanial drug (JNII40_base) and its hydrochloride salt (JNII40_HCl). Methods: The characterization studies performed allowed us to determine the crystallinity, hydration water, and presence of hydrogen bonds in these drugs. Different dissolution methods were employed to predict intestinal absorption. A high-performance liquid chromatography–mass spectrophotometry (HPLC-MS/MS) method was developed for the determination of JNII40 in plasma. Results: Pharmacokinetic studies in rats of JNII40_base at 100 and 20 mg/kg, and JNII40_HCl at 20 mg/kg, showed a non-linear pharmacokinetic at high doses. An innovative biorelevant medium of phosphate buffer pH 6.8 with polysorbate 80 at 0.6% (w/v) showed high concentration values for JNII40_base at 30 min, which predicts good intestinal absorption. These results were consistent with the bioavailability data, which exhibited a significant (p < 0.05) increase in maximum plasma concentration (C_max) and a slight delay in time to maximum (T_max) compared to JNII40_HCl. Furthermore, the sustained release of JNII40_base in this biorelevant media was related to high plasma concentration values at 24 h (C_24h) observed in bioavailability studies. These plasma concentrations of JNII40_base were above the half-maximal inhibitory concentration (IC₅₀) against promastigote and amastigote forms of Leishmania donovani, which is indicative of effectiveness and should reduce the occurrence of drug resistance during treatments. Conclusions: The bioavailability and pharmacokinetic data support the consideration of this drug for further in vivo studies as an oral antileishmanial treatment. Full article

High turbidity in raw water poses a major challenge to drinking water quality and requires effective, sustainable treatment solutions. This work investigates the reduction in turbidity in raw water and the enhancement of overall drinking water quality through the coagulation–flocculation process. The performance of Pine cone extract as a bio-coagulant was evaluated using four different solvent-based extractions (PC-H₂O, PC-HCl, PC-NaCl, and PC-NaOH). The effects of key operational parameters were analyzed, and jar tests were carried out to enhance the coagulation–flocculation process by identifying the optimal conditions. Experimental design was further refined using RSM based on a BBD, incorporating three factors: initial pH, coagulant dosage, and settling time, with turbidity removal efficiency as the response variable. Statistical analysis confirmed that initial pH, coagulant dosage, and settling time significantly influenced turbidity reduction at a confidence level of p-value < 0.05 for all four solvents. Among the extracts tested, PC-HCl demonstrated the highest turbidity removal efficiency. The optimal conditions achieving 78.57% turbidity reduction were a pH of 8.5, a coagulant dosage of 100 mL/L, and a settling time of 120 min. These findings highlight the significant potential of Pine cone extract as an effective, sustainable, and eco-friendly organic coagulant for raw water treatment. Full article

In this study, polyvinyl alcohol (PVA) films were reinforced with lignocellulosic nanofibers (LCNFs) extracted from bamboo shoot shells using a choline chloride-based deep eutectic solvent (DES). A filler loading of 10 wt% was identified as the optimal condition for enhancing film performance. To improve interfacial compatibility between the PVA matrix and LCNFs, three surface modification treatments were applied to the nanofibers: hydrochloric acid (HCl) hydrolysis, citric acid (CA) crosslinking, and a dual modification combining both methods (HCl&CA). Among all formulations, films incorporating dual-modified LCNF at 10 wt% loading exhibited the most significant improvements. Compared to neat PVA, these composites showed a 79.2% increase in tensile strength, a 15.1% increase in elongation at break, and a 33.1% enhancement in Young’s modulus. Additionally, thermal stability and barrier properties were improved, while water swelling and solubility were reduced. Specifically, the modified films achieved a thermal residue of 9.21% and the lowest degradation rate of 10.81%/min. Water vapor transmission rate and oxygen permeability decreased by 18.8% and 18.6%, respectively, and swelling and solubility dropped to 14.26% and 3.21%. These results highlight the synergistic effect of HCl hydrolysis and CA crosslinking in promoting uniform filler dispersion and strong interfacial adhesion, offering an effective approach to valorizing bamboo shoot shell waste into high-performance, eco-friendly packaging materials. Full article