Abstract
Water channeling in offshore unconsolidated sandstone reservoirs motivates the development of injectable gels for water shutoff. A polymer prepared from acrylamide, N-vinylpyrrolidone, and cetyl methacrylate (designated ANC16) was combined with polyethyleneimine (PEI) and evaluated by FTIR, 1H NMR, dry-sample thermogravimetry, Sydansk bottle tests, and sand-pack flooding. FTIR and 1H NMR support the proposed functional groups and structural motifs of the precursor polymer. The formulation selected from the tested concentration series contained 0.5 wt% ANC16 and 0.25 wt% PEI. At 35,000 mg/L total salinity, the time to reach Sydansk grade D decreased from 64 to 22 h as temperature increased from 30 to 110 °C. Grade-H gels were observed at salinities of 0–30,000 mg/L at 90 °C. In the sand-pack experiment at 90 °C and 35,000 mg/L, the maximum precursor injection pressure was 0.185 MPa, and subsequent treatment reduced water-phase permeability by 97.85%. During flooding at 1 mL/min, injection pressure remained near 2.2 MPa from approximately four to 20 pore volumes. These results demonstrate delayed gel development, laboratory injectivity, and sustained flow restriction over the tested interval.
1. Introduction
Polymer gels are used to control excessive water production by restricting flow through preferential pathways. Their performance depends on polymer structure, crosslinker chemistry, gelation time, and network stability under reservoir conditions. International studies distinguish near-wellbore water shutoff from deeper profile modification, for which gel placement and propagation are critical design considerations [1]. Both in situ gels and preformed particle gels have been investigated, but their transport and plugging mechanisms differ and must be matched to the target formation [2].
In offshore unconsolidated sandstone reservoirs, preferential flow through high-permeability pathways can reduce the efficiency of waterflooding. Limited platform space and operational constraints increase the importance of injectivity, an adequate placement window, and reliable plugging after gelation. Li et al. reported that a dispersed-particle-gel-based heterogeneous flooding system improved the injection profile and maintained resistance to subsequent water flooding [3]. For an in situ gel intended for these formations, the corresponding challenge is to balance precursor transport with subsequent network formation, while assessing compatibility with reservoir temperature and salinity.
Particle-based systems provide useful comparisons for transport and plugging. Wang et al. developed polymer microspheres for high-temperature, high-salinity conditions [4], while Yue et al. used direct visualization to examine remaining-oil distribution after nano-micron polymer-particle injection [5]. In partially open fractures, Wang et al. investigated how treatment conditions affect preformed-particle-gel placement, dehydration, and plugging [6]. Zanoni et al. studied hydrophilic polymer nanoparticles for water shutoff and progressed to a pilot field application [7]. Selective plugging has also been investigated using microfoam in shallow, low-temperature reservoirs [8]. These approaches involve different transport or phase-behavior mechanisms from an in situ gel of an acrylamide (AM)/N-vinylpyrrolidone (NVP)/cetyl methacrylate (C16MA) terpolymer (ANC16) crosslinked with polyethyleneimine (PEI) and provide context rather than direct evidence of its performance.
Different formulation strategies have been explored to improve gel performance. Ding et al. investigated PAM/phenolic gels for low-temperature, high-salinity reservoirs [9]. Ge et al. examined the formulation and stability of temperature- and salinity-resistant phenolic gels [10], and Yang et al. improved low-temperature gelation of an HPAM/phenol–formaldehyde system using a promoter [11]. Guo et al. studied nano-SiO2 reinforcement of high-temperature gels [12], while Li et al. developed an HPAM/water-soluble phenol–formaldehyde resin system for high-temperature profile control [13]. Kang et al. prepared an amine-modified lignin gel crosslinked with polyethylene glycol diglycidyl ether for water plugging [14]. Dang et al. also investigated a hydrophobically associating AM/AMPS/DMC/NVP polymer with a phenolic crosslinker and additives for high-temperature, high-salinity water plugging [15]. These studies support careful selection of polymer and crosslinker chemistry, but their results cannot be transferred directly to ANC16/PEI because the formulations and test conditions differ.
PEI-crosslinked polyacrylamide systems provide a relevant basis for delayed gel design. Al-Muntasheri et al. quantified the effects of temperature, concentration, and salinity on the gelation kinetics of a polyacrylamide/tert-butyl acrylate–PEI system [16]. Their subsequent comparison of PAM/PEI and copolymer/PEI gels examined reaction mechanisms and the effects of pH and salts [17]. Zhao et al. evaluated high-strength PAtBA/PEI gels, including the effects of crosslinker molecular weight and formulation conditions [18]. Ghriga et al. investigated how polymer hydrolysis degree, molecular weight, and concentration influence PHPA/PEI gelation [19]; their experimental-design study also demonstrated interacting effects of salinity, temperature, and reactant concentrations [20]. These findings motivate evaluating the placement window and final gel strength together.
Reinforcement and solvent modification offer additional ways to regulate these systems. Amir et al. showed that silica nanoparticles could strengthen weakened PAM/PEI gels [21], while Soka and Sidiq evaluated nanomaterial and formulation effects for water shutoff in carbonate rocks [22]. Adewunmi et al. studied coal-fly-ash reinforcement of PAM/PEI gels [23]. Tessarolli et al. examined an AM/AMPS/NVP terpolymer crosslinked with PEI and reinforced with bentonite, reporting changes in gelation time and stability [24]. Reena et al. investigated PVA/PVP-based hydrogels and their blends for water shutoff [25]. These studies illustrate alternatives in polymer architecture and reinforcement; the present ANC16/PEI formulation does not contain these particulate fillers.
Recent international studies further broaden this background. Telin et al. investigated polyacrylamide/polysaccharide hydrogels for high-temperature water shutoff [26]. Marques et al. showed that a water/glycerol mixture delayed PAM/PEI gelation and that diethylenetriamine reduced syneresis [27]. Sandoval Martinez et al. designed a dual molecular weight HPAM/PEI formulation to combine low initial viscosity with delayed gelation for a reservoir with an active aquifer [28]. Together, these results show that formulation design can modify the balance between injectivity, gelation time, and gel stability, while performance remains dependent on reservoir conditions.
This work combines an AM/NVP/C16MA polymer with PEI-mediated delayed gelation and evaluates the formulation in a sand-pack model relevant to offshore unconsolidated sandstone reservoirs. Previous studies of PAM and acrylamide copolymers provide the formulation background [16,17]. Compared with the AM/AMPS/NVP–PEI/bentonite system of Tessarolli et al. [24], ANC16 introduces ester-linked C16 side chains without particulate reinforcement. The monomer selection also distinguishes this approach from solvent/additive adjustment [27] and dual molecular weight HPAM/PEI blending [28]. The study relates precursor characterization and formulation-dependent gel development to injectivity, permeability reduction, and resistance to subsequent water flooding.
2. Results and Discussion
2.1. Characterization of ANC16
2.1.1. Molecular Architecture
ANC16 was prepared by APS/NaHSO3-initiated free-radical polymerization of AM, NVP, and C16MA at 35 °C (Section 4.2). This synthesis consumes the monomer vinyl groups to form a carbon–carbon backbone; PEI is introduced subsequently for gel preparation. Scheme 1 depicts the proposed repeat units: AM supplies pendant primary amides, NVP supplies five-membered lactam rings attached to the backbone through nitrogen, and C16MA supplies ester-linked cetyl groups together with a backbone methyl substituent. The amide and lactam groups provide polar sites, while the cetyl groups provide sites for hydrophobic association. The C16MA-derived ester is also a potential site for post-polymerization aminolysis or hydrolysis, as discussed in Section 2.2.1.
Scheme 1.
The proposed repeat-unit connectivity of ANC16 before PEI addition. The subscripts x, y, and z indicate the three repeat-unit types without specifying their relative abundance or sequence.
The AM:NVP:C16MA mass ratio of 27:9:1 is the monomer feed ratio. FTIR and the 1H NMR spectrum in Section 2.1.4 support the proposed functional groups and structural motifs; the repeat-unit fractions are not quantified by the reported spectral assignments.
2.1.2. FTIR Analysis
Figure 1 presents the FTIR spectrum of ethanol-precipitated and washed ANC16 before PEI addition. The bands at 3360 and 3170 cm−1 are consistent with primary-amide N-H stretching, and the feature near 1602 cm−1 is consistent with amide N-H bending. The strong band at 1676 cm−1 is assigned primarily to carbonyl stretching in the amide region; a lactam contribution from NVP-derived units may overlap with AM-derived amide absorption and cannot be resolved independently. The feature near 1430 cm−1 is consistent with aliphatic C-H deformation, while the 1273 and 1136 cm−1 features are tentatively associated with C-N and C-O vibrations. These fingerprint-region assignments are not unique identifiers of the individual comonomers.
Figure 1.
Infrared spectrum of ANC16.
The feature near 1430 cm−1 is compatible with aliphatic groups, but the overlapping FTIR bands provide limited discrimination between the three repeat units. The 1H NMR analysis in Section 2.1.4 provides complementary information on the pyrrolidone and cetyl environments.
The spectrum characterizes ANC16 before PEI addition. Its functional-group assignments provide the starting point for discussing the possible interactions during subsequent gel formation.
2.1.3. TGA of ANC16
TGA was performed to examine the thermal mass-loss behavior of isolated ANC16 (Figure 2). Below 150 °C, the mass loss was less than 10% and was accompanied by a thermal feature near 100 °C, consistent with loss of retained water or other volatile species. Further mass loss occurred between approximately 150 and 380 °C, followed by a sharper decrease between 380 and 500 °C; the residue at 800 °C was approximately 8%. The broad, overlapping mass-loss stages indicate progressive thermal decomposition of the dry polymer sample. Aqueous-gel stability under reservoir conditions is assessed separately from this dry-sample response.
Figure 2.
Thermogravimetric analysis plot for ANC16.
2.1.4. Nuclear Magnetic Hydrogen Spectrum of ANC16
As shown in Figure 3,The 1H NMR spectrum exhibits aliphatic resonances at approximately δ 0.8–2.5 ppm, consistent with the expected polymer backbone and alkyl-chain environments. Signals within δ 1.8–2.5 ppm and near δ 3.2 ppm are compatible with the pyrrolidone-ring methylene groups associated with NVP. The terminal methyl and long-chain methylene signals near δ 0.8 ppm and within δ 1.2–1.7 ppm, together with possible ester-adjacent methylene contributions around δ 3.7–4.0 ppm, are consistent with the cetyl-containing structure of C16MA. These spectral features support the proposed structural motifs of the material prepared from AM, NVP, and C16MA.
Figure 3.
1H NMR spectrum of ANC16.
2.2. Construction of the Delayed Crosslinking Water Shutoff System
2.2.1. Selection of the Delayed Crosslinker
Water shutoff gels can use metal-ion, phenolic, or PEI-based crosslinking chemistries [1]. The useful gelation window depends on the polymer, crosslinker, temperature, pH, and salinity; therefore, a uniformly short gelation time should not be assumed for all metal-ion systems. Phenolic systems have also been developed for different reservoir temperatures and salinities [9,13]. PEI-based systems were selected here because prior studies demonstrated temperature- and concentration-dependent gelation of acrylamide-containing polymers [16,17], providing a basis for investigating delayed gel formation in ANC16.
The ANC16/PEI formulation contains chemically distinct amide, lactam, ester, and amine groups. Direct substitution of an unactivated AM-derived amide by a PEI amine is not an adequate basis for assigning the gelation mechanism at 90 °C in water without an added catalyst. Although NMR studies have examined amide-related reactions and hydrolysis in PHPA/PEI mixtures [29], those findings concern a different polymer system. For ANC16, the pendant C16MA-derived ester provides an alternative acyl substitution site: aminolysis by a primary PEI amine would form a polymer-bound amide linkage and release cetyl alcohol (Scheme 2a). Multiple attachments to different polymer chains could then provide covalent junctions. Studies of polymer-ester amidation show that amine nucleophilicity, steric accessibility, and polymer solvation affect the reaction [30]; the rate and extent of this pathway in aqueous ANC16/PEI remain to be determined.
Scheme 2.
Candidate chemical transformations and ionic association in aqueous ANC16/PEI. P represents the polymer residue attached to the carbonyl carbon, and R represents a PEI segment. The arrows show formal reaction stoichiometries, not measured conversions. In (c), association requires both carboxylate and protonated amine sites.
PEI is a polybase: protonation of its amines in water can increase hydroxide concentration. Under sufficiently alkaline conditions, hydrolysis of pendant amide or ester groups would generate carboxylate sites (Scheme 2b). These sites can associate with protonated PEI amines, with the balance between hydrolysis, amine protonation, and ionic association depending on pH and brine composition. Hydrolysis alone does not create a covalent bridge between ANC16 and PEI. Ester aminolysis and ester hydrolysis would both remove cetyl groups from the affected repeat units, linking chemical conversion to changes in hydrophobic association. Hydrogen bonding and association among the remaining C16 groups may also contribute to network formation. The present precursor spectra and bottle tests do not resolve the relative contributions of these pathways. PEI (Mw = 25,000) supplied as a 50 wt% aqueous solution was used to evaluate formulation-dependent gelation.
2.2.2. Effect of ANC16 Concentration on Gel System Performance
The PEI concentration was fixed at 0.2 wt%, and the experimental temperature was maintained at 90 °C. The effects of ANC16 concentration on the gelation behavior of the system were investigated by adjusting the ANC16 mass fraction to 0.2, 0.3, 0.4, 0.5, and 0.6 wt%. The gelation time and stable gel strength were evaluated using the Sydansk gel strength code method [31], and the results are presented in Table 1.
Table 1.
Influence of ANC16 Concentration on Gel System Performance.
As the ANC16 concentration increased from 0.2 to 0.6 wt%, the gelation time decreased from 59 to 36 h, while the gel strength increased from grade D to grade G (Table 1). Increasing the polymer concentration increases the availability of chains and functional groups for intermolecular interactions. Increasing ANC16 from 0.5 to 0.6 wt% shortened the gelation time from 41 to 36 h without improving the final strength code. Therefore, 0.5 wt% ANC16 was selected for subsequent formulation tests.
2.2.3. Effect of PEI Concentration on Gel System Performance
The ANC16 concentration was fixed at 0.5 wt%, and the temperature was maintained at 90 °C. The effect of PEI concentration on gel performance was investigated by adjusting the PEI mass fraction to 0.10, 0.15, 0.20, 0.25, and 0.30 wt%. The results are shown in Table 2.
Table 2.
Effect of PEI concentration on the performance of the gel system.
Increasing the PEI concentration from 0.10 to 0.30 wt% shortened the gelation time from 56 to 33 h. Gel strength increased from grade E to grade H at 0.25 wt% PEI and then decreased to grade G at 0.30 wt% (Table 2). The PEI concentration of 0.25 wt% was selected because it gave the highest strength code in this series. The different responses of gelation time and final strength indicate that increasing PEI beyond this concentration did not improve both screening criteria.
The concentration dependence is consistent with PAM/PEI rheological studies showing different effects of polymer and crosslinker concentrations on gel strength [32]. Here, gelation time denotes the grade-D bottle-test endpoint, and final strength is an ordinal Sydansk code. Table 1, Table 2, Table 3 and Table 4 report individual observations rather than replicate means.
Table 3.
Effect of salinity on the performance of the gel system.
Table 4.
Effect of temperature on the performance of the gel system.
2.2.4. Effect of Salinity on Gel System Performance
Offshore formation water generally exhibits high salinity, which can adversely affect the molecular conformation of polyacrylamide-based polymers and consequently deteriorate gel performance. In this study, the gel system containing 0.5 wt% ANC16 and 0.25 wt% PEI was evaluated at 90 °C under different salinity conditions to investigate the effect of salinity on gelation behavior. The results are presented in Table 3.
Increasing total salinity from 0 to 30,000 mg/L shortened the grade-D time from 37 to 26 h, while the final strength code remained H. At 40,000 and 50,000 mg/L, the times increased to 33 and 39 h and the strength codes decreased to G and F, respectively (Table 3). Thus, the formulation maintained grade-H strength across the lower salinity range but showed slower gel development and lower strength at the two highest salinities. Salt can alter chain solvation, ionic association, and hydrophobic interactions; distinguishing these contributions requires brine composition and pH data together with a matched AM/NVP control.
2.2.5. Effect of Temperature on Gel System Performance
To prevent premature gelation near the wellbore during injection, the gelation behavior of the ANC16/PEI system was evaluated at different temperatures. The gel system consisted of 0.5 wt% ANC16 and 0.25 wt% PEI, and formation water with a total salinity of 35,000 mg/L was used. The results are shown in Table 4.
Increasing temperature shortened the grade-D time, consistent with faster gel development under the tested conditions. At 30 °C, this endpoint was reached after 64 h; at 90 °C it was reached after 28 h with a final strength code of H, and at 110 °C after 22 h with the same code. This temperature dependence describes the overall evolution of the formulation, which may include chemical conversion and physical association. Calorimetric analysis has been used in related PAM/PEI systems to distinguish thermal events associated with gel development [33].
2.3. Comprehensive Performance Evaluation of the Delayed Crosslinking System
2.3.1. Injectivity Evaluation
A sand-packed tube with a nominal permeability of 1000 × 10−3 μm2 was used at 90 °C and 35,000 mg/L total salinity. During injection of 1 PV of precursor solution, the inlet pressure increased gradually to a maximum of 0.185 MPa without a sharp rise (Figure 4). This pressure response supports precursor injectivity under the applied flow conditions. Spatially resolved measurements would be needed to determine the placement depth.
Figure 4.
The variation in injection pressure before plugging as a function of injection volume.
2.3.2. Plugging Performance Evaluation
Following precursor injection and 48 h of shut-in at 90 °C, water flooding was used to assess the overall permeability change. The water-phase permeability decreased from 996.74 × 10−3 to 21.39 × 10−3 μm2, corresponding to a plugging efficiency of 97.85% (Figure 5). This whole-sand-pack response demonstrates treatment-induced flow restriction.
Figure 5.
Permeability before and after water shutoff.
Published PAM/PEI tests have combined thermal aging, rheology, and flooding in sandstone and carbonate cores to evaluate injectivity and persistence of permeability reduction [34]. Those results emphasize that a high initial plugging efficiency should be complemented by aging and flow tests over relevant durations. The present sand-pack results therefore support laboratory plugging performance, while longer-term durability remains to be evaluated.
2.3.3. Flow Resistance During 20 PV of Water Flooding
After the plugging test, water was injected at 1 mL/min to evaluate flow resistance over a cumulative throughput of 20 PV (Figure 6). The inlet pressure rose during the initial stage and remained near 2.2 MPa from approximately 4 to 20 PV. The absence of a sustained pressure decline indicates persistence of hydraulic resistance over this throughput interval.
Figure 6.
The variation in injection pressure following plugging as a function of injection volume.
Long-term performance in hot brine requires complementary aging measurements of syneresis, mechanical strength, and post-aging permeability reduction. These measurements would connect changes in gel volume and network properties to sustained water shutoff performance.
3. Conclusions
ANC16 was prepared by redox-initiated free-radical polymerization of AM, NVP, and C16MA. FTIR and 1H NMR support the proposed precursor functional groups and structural motifs. Subsequent mixing with PEI produced delayed gel development; ester aminolysis, hydrolysis-dependent ionic association, and physical interactions provide candidate contributions to this behavior. Bottle-test screening selected 0.5 wt% ANC16 and 0.25 wt% PEI. At 35,000 mg/L total salinity, grade-D times decreased from 64 to 22 h between 30 and 110 °C; grade-H gels were obtained at 0–30,000 mg/L at 90 °C. Sand-pack treatment reduced water-phase permeability by 97.85%, and inlet pressure remained near 2.2 MPa during subsequent flooding from approximately 4 to 20 PV. The formulation therefore combines a delayed bottle-test response with laboratory injectivity and flow restriction over the evaluated interval.
4. Materials and Methods
4.1. Materials
4.1.1. Chemicals
AM, NVP, C16MA, ammonium persulfate (APS), sodium bisulfite (NaHSO3), and sodium dodecyl sulfate (SDS) were analytical-grade reagents purchased from Shanghai Macklin Biochemical Technology Co., Ltd., Shanghai, China. PEI (Mw = 25,000, 50 wt% aqueous solution) was purchased from the same company. Ethanol and sodium hydroxide (NaOH) were analytical-grade reagents purchased from Sinopharm Chemical Reagent Co., Ltd., Shanghai, China.
The salinity-series tests used total salinities of 0, 10,000, 20,000, 30,000, 40,000, and 50,000 mg/L; the temperature-series and sand-pack tests used simulated formation water at 35,000 mg/L. The reported brine descriptor is total salinity; salt-by-salt composition and measured pH were not recorded.
4.1.2. Instruments
The instruments used in this study included a DF-101S thermostatic heating and magnetic stirring water bath (Shanghai Lichen Bangxi Instrument Technology Co., Ltd., Shanghai, China); an UPT-1-5 ultrapure water purification system (Sichuan ULUPURE Ultrapure Technology Co., Ltd., Chengdu, China); an LY15-9246A electric thermostatic blast drying oven (Shanghai Longyue Instrument Equipment Co., Ltd., Shanghai, China); an IRTracer-100 Fourier transform infrared (FTIR) spectrometer (Shimadzu, Japan); a TGA 2 thermogravimetric analyzer (Shimadzu, Japan); an ML-T precision balance (METTLER TOLEDO, Greifensee, Switzerland); and a multifunctional core flooding system (Jiangsu Haian Petroleum Scientific Research Instrument Co., Ltd., Nantong, China).
4.2. Preparation of ANC16
AM, NVP, and C16MA monomers were added to deionized water at a mass ratio of 27:9:1. SDS was added to form a micellar dispersion system, and the mixture was continuously stirred until a homogeneous dispersion was obtained. Nitrogen gas was continuously purged through the reaction system for 30 min to remove dissolved oxygen. Subsequently, an APS/NaHSO3 redox initiator system was added, and the reaction was conducted at 35 °C in a water bath under constant stirring for 4 h. After completion of the polymerization reaction, the product was slowly poured into anhydrous ethanol for precipitation. The precipitate was collected by filtration, repeatedly washed with ethanol, dried at a constant temperature, and then crushed and sieved to obtain the isolated material designated ANC16.
ANC16 was isolated by ethanol precipitation, filtration, repeated ethanol washing, and drying before PEI was added for gel preparation. Thus, precursor synthesis and subsequent PEI-mediated gelation are separate stages.
4.3. Experimental Methods
4.3.1. Fourier Transform Infrared Spectroscopy (FTIR) Characterization
Ethanol-precipitated, washed, and dried ANC16 before mixing with PEI was characterized using an IRTracer-100 FTIR spectrometer by the KBr pellet method. A small amount of sample was mixed with KBr and ground thoroughly in an agate mortar. The KBr pellets were prepared by pressing the mixture at 2 MPa for 5 min, and the FTIR spectra were recorded at room temperature over a wavenumber range of 1000–4000 cm−1 with a resolution of 4 cm−1.
4.3.2. Thermogravimetric Analysis (TGA)
TGA was performed to investigate the thermal decomposition behavior of the samples. A small amount of dried sample was placed in a crucible, and the measurement was conducted according to the preset program. The temperature was increased from 30 to 800 °C at a heating rate of 10 °C/min under a nitrogen atmosphere.
4.3.3. Gelation Performance Evaluation
Gel development was assessed using the qualitative Sydansk strength codes listed in Table 5. The time required to reach grade D was defined operationally as the bottle-test gelation time [31]. The reported endpoints and final strength codes are individual visual observations; rheological moduli and replicate-based uncertainty were not measured.
Table 5.
Sydansk gel strength code classification [31].
4.3.4. Injectivity Evaluation of the Gel Precursor
The gel precursor was injected into the sand-packed tube at 0.5 mL/min to a volume of 1 PV, with inlet pressure recorded against injected volume. After injection, the inlet and outlet valves were closed and the system was held at 90 °C for 48 h. Injectivity was evaluated from the inlet-pressure response during precursor injection.
4.3.5. Plugging Efficiency Evaluation of the Gel System
Simulated formation water was injected at a constant flow rate of 0.5 mL/min until the inlet and outlet pressures became stable. The initial water-phase permeability (K1) was calculated. After injection of the gel precursor solution and sufficient crosslinking, subsequent water flooding was conducted at the same flow rate of 0.5 mL/min. The pressure profile was recorded until a new steady-state pressure was reached. The post-treatment water-phase permeability (K2) was calculated, and the plugging efficiency was determined according to Equation (1):
where τ represents the plugging efficiency, K1 represents the water-phase permeability before water shutoff treatment (10−3 μm2), and K2 represents the water-phase permeability after water shutoff treatment (10−3 μm2).
4.3.6. Flow Resistance During Water Flooding
Following the plugging test, the water flow rate was increased to 1 mL/min and inlet pressure was monitored until the cumulative throughput reached 20 PV. Pressure persistence was used to assess hydraulic resistance over this interval.
Author Contributions
Conceptualization, J.H., J.S. (Jian Sun) and J.S. (Jinsheng Sun); methodology, J.H., J.S. (Jian Sun) and C.W.; formal analysis, J.H., J.W. and B.L.; investigation, J.H., Y.Y. and M.C.; resources, C.W. and J.S. (Jinsheng Sun); data curation, J.W., B.L. and Y.Y.; writing—original draft preparation, J.H. and J.S. (Jian Sun); writing—review and editing, C.W., J.W., B.L., Y.Y., M.C. and J.S. (Jinsheng Sun); supervision, J.S. (Jinsheng Sun); funding acquisition, J.S. (Jinsheng Sun). All authors have read and agreed to the published version of the manuscript.
Funding
This work was supported by the Basic Science Center Project of the National Natural Science Foundation of China (52288101) “Flow Control of Ultra-deep and Extra-deep Oil and Gas Drill-ing”.
Institutional Review Board Statement
Not applicable.
Informed Consent Statement
Not applicable.
Data Availability Statement
The data supporting the findings of this study are available within the article.
Conflicts of Interest
Authors Junli Huang and Chen Wang were employed by the company Shenzhen Branch of CNOOC China Limited. Author Jinsheng Sun was employed by the company CNPC Engineering Technology R&D Company Limited. The remaining authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
References
- El-Karsani, K.S.; Al-Muntasheri, G.A.; Hussein, I.A. Polymer systems for water shutoff and profile modification: A review over the last decade. SPE J. 2014, 19, 135–149. [Google Scholar] [CrossRef] [Scilit]
- Ma, W.; Li, Y.; Liu, P.; Liu, Z.; Song, T. Progress of research into preformed particle gels for profile control and water shutoff techniques. Gels 2024, 10, 372. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Li, H.; Wang, K.; Han, X.; Zheng, J. Research on heterogeneous compound flooding system based on dispersed particle gel. Adv. Geo-Energy Res. 2019, 3, 156–164. [Google Scholar] [CrossRef] [Scilit]
- Wang, X.; Sun, Z.; Zhang, J.; Fang, S.; Huang, J. Preparation of ultra-high temperature and high salinity resistant polymer microsphere and its property evaluation. J. Mol. Liq. 2025, 421, 126910. [Google Scholar] [CrossRef] [Scilit]
- Yue, M.; Zhu, W.; Han, H.; Song, H.; Long, Y.; Lou, Y. Experimental research on remaining oil distribution and recovery performances after nano-micron polymer particles injection by direct visualization. Fuel 2018, 212, 506–514. [Google Scholar] [CrossRef] [Scilit]
- Wang, Z.; Bai, B.; Sun, X.; Wang, J. Effect of multiple factors on preformed particle gel placement, dehydration, and plugging performance in partially open fractures. Fuel 2019, 251, 73–81. [Google Scholar] [CrossRef] [Scilit]
- Zanoni, A.; Pesce, R.M.; Sponchioni, M.; Del Gaudio, L.; Lorefice, R.; Albonico, P.; Belloni, A.; Cesana, A.; Morbidelli, M.; Moscatelli, D. Synthesis and Application of Hydrophilic Polymer Nanoparticles for Water Shut-Off. Energy Fuels 2022, 36, 1874–1881. [Google Scholar] [CrossRef] [Scilit]
- Yang, E.; Fang, Y.; Liu, Y.; Li, Z.; Wu, J. Research and application of microfoam selective water plugging agent in shallow low-temperature reservoirs. J. Pet. Sci. Eng. 2020, 193, 107354. [Google Scholar] [CrossRef] [Scilit]
- Ding, F.; Dai, C.; Sun, Y.; Zhao, G.; You, Q.; Liu, Y. Gelling behavior of PAM/phenolic crosslinked gel and its profile control in a low-temperature and high-salinity reservoir. Gels 2022, 8, 433. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Ge, J.J.; Guo, H.B.; Zhang, T.C.; Zhou, D.Y.; Xu, Y.; Lü, Q. Development of temperature and salinity resistant phenolic gel and its performance regulation mechanism. Acta Pet. Sin. 2022, 43, 1145–1157. [Google Scholar]
- Yang, W.H.; Ge, H.J.; Xu, J.N.; Cheng, J.; Yuan, X.X.; He, P.X. Gelation improvement of phenol-formaldehyde cross-linking HPAM system at low temperature. Oilfield Chem. 2019, 36, 630–635. [Google Scholar]
- Guo, H.; Ge, J.; Li, L.; Zhang, G.; Li, Z.; Wang, W.; Liu, M. New insights and experimental investigation of high-temperature gel reinforced by nano-SiO2. Gels 2022, 8, 362. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Li, X.; Liu, S.; Zhang, J.; Han, S.; Zhao, L.; Xu, A.; Wang, J.; Zhou, F.; Li, M. High-temperature-resistant profile control system formed by hydrolyzed polyacrylamide and water-soluble phenol-formaldehyde resin. Gels 2024, 10, 413. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Kang, Z.; Ma, Q.J.; Geng, S.; Shi, X.; Li, S.L.; Wang, K.Y.; Wen, Y.B. Preparation and application of temperature and salt-resistant water-plugging gel based on amine-modified lignin. Chem. Eng. Oil Gas 2025, 54, 100–106. [Google Scholar]
- Dang, Y.B.; Pu, L.T.; Xing, Z.L.; Jia, Z.W.; Ma, Z.Y.; Zhao, Y.B.; Zhu, W.N.; Xu, L.M. Research and application of gel plugging agent for high-temperature and high-salt reservoir. J. Xi’an Shiyou Univ. (Nat. Sci. Ed.) 2025, 40, 65–70. [Google Scholar]
- Al-Muntasheri, G.A.; Nasr-El-Din, H.A.; Hussein, I.A. A rheological investigation of a high temperature organic gel used for water shut-off treatments. J. Pet. Sci. Eng. 2007, 59, 73–83. [Google Scholar] [CrossRef] [Scilit]
- Al-Muntasheri, G.A.; Nasr-El-Din, H.A.; Al-Noaimi, K.R.; Zitha, P.L.J. A study of polyacrylamide-based gels crosslinked with polyethyleneimine. SPE J. 2009, 14, 245–251. [Google Scholar] [CrossRef] [Scilit]
- Zhao, S.; Ge, J.J.; Zhu, J.; Zhang, H.H. Research on high-strength PEI gel used for oil well water plugging. Oilfield Chem. 2021, 38, 434–439. [Google Scholar]
- Ghriga, M.A.; Gareche, M.; Khodja, M.; Andreu, N.; Lebouachera, S.E.I.; Khoukh, A.; Drouiche, N.; Grassl, B. Structure–property relationships of the thermal gelation of partially hydrolyzed polyacrylamide/polyethylenimine mixtures in a semidilute regime. Polym. Bull. 2020, 77, 1465–1488. [Google Scholar] [CrossRef] [Scilit]
- Ghriga, M.A.; Hasanzadeh, M.; Gareche, M.; Lebouachera, S.E.I.; Drouiche, N.; Grassl, B. Thermal gelation of partially hydrolysed polyacrylamide/polyethylenimine mixtures using design of experiments approach. Mater. Today Commun. 2019, 21, 100686. [Google Scholar] [CrossRef] [Scilit]
- Amir, Z.; Mohd Saaid, I.; Mohd Junaidi, M.U.; Wan Bakar, W.Z. Weakened PAM/PEI polymer gel for oilfield water control: Remedy with silica nanoparticles. Gels 2022, 8, 265. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Soka, S.; Sidiq, H. Sensitivity analysis of parameters affecting nano-polymer solution for water shutoff in carbonate rocks. Adv. Geo-Energy Res. 2022, 6, 230–240. [Google Scholar] [CrossRef] [Scilit]
- Adewunmi, A.A.; Ismail, S.; Sultan, A.S. Study on strength and gelation time of polyacrylamide/polyethyleneimine composite gels reinforced with coal fly ash for water shut-off treatment. J. Appl. Polym. Sci. 2015, 132, 41392. [Google Scholar] [CrossRef] [Scilit]
- Tessarolli, F.G.C.; Souza, S.T.S.; Gomes, A.S.; Mansur, C.R.E. Gelation Kinetics of Hydrogels Based on Acrylamide–AMPS–NVP Terpolymer, Bentonite, and Polyethylenimine for Conformance Control of Oil Reservoirs. Gels 2019, 5, 7. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Reena; Kumar, A.; Mahto, V.; Choubey, A.K. Synthesis and characterization of cross-linked hydrogels using polyvinyl alcohol and polyvinyl pyrrolidone and their blend for water shut-off treatments. J. Mol. Liq. 2020, 301, 112472. [Google Scholar] [CrossRef] [Scilit]
- Telin, A.; Sergeeva, N.; Asadullin, R.; Gusarova, E.; Yakubov, R.; Dokichev, V.; Politov, A.; Sunagatova, E.; Gibadullina, N.; Teptereva, G.; et al. Polyacrylamide and polyacrylamide/polysaccharide hydrogels for well water shutoff in high-temperature reservoirs. Gels 2025, 11, 862. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Marques, N.N.; de Morais, S.C.; da Câmara, P.C.F.; de Souza, E.A.; Balaban, R.C. Gelation behavior of polyacrylamide-polyethyleneimine: Effects of diethylenetriamine and glycerol addition. J. Braz. Chem. Soc. 2023, 34, 1373–1379. [Google Scholar] [CrossRef] [Scilit]
- Sandoval Martinez, M.I.; Salgado Carabali, V.; Ramirez, A.; Chaves-Guerrero, A.; Muñoz Navarro, S. Design of a dual molecular weight polymer gel for water-shutoff treatment in a reservoir with active aquifer. Polymers 2025, 17, 1399. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Ghriga, M.A.; Khoukh, A.; Lebouachera, S.E.I.; Grassl, B. NMR investigation on the thermogelation of partially hydrolysed polyacrylamide/polyethylenimine mixtures. Soft Matter 2022, 18, 7075–7081. [Google Scholar] [CrossRef] [Scilit] [PubMed]
- Van Guyse, J.F.R.; Verjans, J.; Vandewalle, S.; De Bruycker, K.; Du Prez, F.; Hoogenboom, R. Full and partial amidation of poly(methyl acrylate) as basis for functional polyacrylamide (co)polymers. Macromolecules 2019, 52, 5102–5109. [Google Scholar] [CrossRef] [Scilit]
- Sydansk, R.D. A new conformance-improvement-treatment chromium(III) gel technology. In Proceedings of the SPE/DOE Enhanced Oil Recovery Symposium, Tulsa, OK, USA, 17–20 April 1988. SPE-17329-MS. [Google Scholar]
- El-Karsani, K.S.M.; Al-Muntasheri, G.A.; Sultan, A.S.; Hussein, I.A. Gelation of a Water-Shutoff Gel at High Pressure and High Temperature: Rheological Investigation. SPE J. 2015, 20, 1103–1112. [Google Scholar] [CrossRef] [Scilit]
- El-Karsani, K.S.M.; Al-Muntasheri, G.A.; Sultan, A.S.; Hussein, I.A. Gelation kinetics of PAM/PEI system. J. Therm. Anal. Calorim. 2014, 116, 1409–1415. [Google Scholar] [CrossRef] [Scilit]
- ElKarsani, K.S.M.; Al-Muntasheri, G.A.; Sultan, A.S.; Hussein, I.A. Performance of PAM/PEI gel system for water shut-off in high temperature reservoirs: Laboratory study. J. Appl. Polym. Sci. 2015, 132, 41869. [Google Scholar] [CrossRef] [Scilit]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content. |
© 2026 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license.







