Search Results (403)

The discharge of oily wastewater threatens the ecosystem and human health, and the efficient treatment of oily wastewater is confronted with problems of high mass transfer resistance at the oil-water-solid multiphase interface, significant light shielding effect, and easy deactivation of photocatalysts. Although traditional physical separation methods avoid secondary pollution by chemicals and can effectively separate floating oil and dispersed oil, they are ineffective in removing emulsified oil with small particle sizes. To address these complex challenges, photocatalytic technology and photocatalysis-based improved technologies have emerged, offering significant application prospects in degrading organic pollutants in oily wastewater as an environmentally friendly oxidation technology. In this paper, the degradation mechanism, kinetic mechanism, and limitations of conventional photocatalysis technology are briefly discussed. Subsequently, the surface interface modulation functions of metal doping and heterojunction energy band engineering, along with their applications in enhancing the light absorption range and carrier separation efficiency, are reviewed. Focus on typical studies on the separation and degradation of aqueous and oily phases using photocatalytic membrane technology, and illustrate the advantages and mechanisms of photocatalysts loaded on the membranes. Finally, other new approaches and converging technologies in the field are outlined, and the challenges and prospects for the future treatment of oily wastewater are presented. Full article

A scalable synthesis of two-dimensional titanium nitride chloride (TiNCl) via flash Joule heating (FJH) using titanium tetrachloride (TiCl₄) precursor has been developed. This single-step method overcomes traditional synthesis challenges, including high energy consumption, multi-step procedures, and hazardous reagent requirements. The structural and chemical properties of the synthesized TiNCl were characterized through multiple analytical techniques. X-ray diffraction (XRD) patterns confirmed the presence of TiNCl phase, while Raman spectroscopy data showed no detectable oxide impurities. Fourier transform infrared spectroscopy (FTIR) analysis revealed characteristic Ti–N stretching vibrations, further confirming successful titanium nitride synthesis. Transmission electron microscopy (TEM) imaging revealed thin, plate-like nanostructures with high electron transparency. These analyses confirmed the formation of highly crystalline TiNCl flakes with nanoscale dimensions and minimal structural defects. The material exhibits excellent structural integrity and phase purity, demonstrating potential for applications in photocatalysis, electronics, and energy storage. This work establishes FJH as a sustainable and scalable approach for producing MXenes with controlled properties, facilitating their integration into emerging technologies. Unlike conventional methods, FJH enables rapid, energy-efficient synthesis while maintaining material quality, providing a viable route for industrial-scale production of two-dimensional materials. Full article

The contamination of drinking water sources with selenium (Se) oxyanions, including selenite (Se(IV)) and selenate (Se(VI)), contains serious health hazards with an oral intake exceeding 400 µg/day and therefore requires urgent attention. Various natural and anthropogenic sources are responsible for high Se concentrations in aquatic environments. In addition, the chemical behavior and speciation of selenium can vary noticeably depending on the origin of the source water. The Se(VI) oxyanion is more soluble and therefore more abundant in surface water. Se levels in contaminated waters often exceed 50 µg/L and may reach several hundred µg/L, well above drinking water limits set by the World Health Organization (40 µg/L) and Germany (10 µg/L), as well as typical industrial discharge limits (5–10 µg/L). Overall, Se is difficult to remove using conventionally available physical, chemical, and biological treatment technologies. The recent literature has therefore highlighted promising advancements in Se removal using emerging technologies. These include advanced physical separation methods such as membrane-based treatment systems and engineered nanomaterials for selective Se decontamination. Additionally, other integrated approaches incorporating photocatalysis coupled adsorption processes, and bio-electrochemical systems have also demonstrated high efficiency in redox transformation and capturing of Se from contaminated water bodies. These innovative strategies may offer enhanced selectivity, removal, and recovery potential for Se-containing species. Here, a current review outlines the sources, distribution, and chemical behavior of Se in natural waters, along with its toxicity and associated health risks. It also provides a broad and multi-perspective assessment of conventional as well as emerging physical, chemical, and biological approaches for Se removal and/or recovery with further prospects for integrated and sustainable strategies. Full article

In sharp contrast to photocatalysis and other prevalent catalytic technologies, tribocatalysis has emerged as a promising technology to degrade high-concentration organic dyes in recent years. In this study, BaTiO₃ (BTO) nanoparticles were challenged to degrade methyl orange (MO) solutions with unprecedentedly high concentrations through magnetic stirring. With BTO nanoparticles and home-made PTFE magnetic rotary disks in 50 mg/L MO solutions, 10 h of magnetic stirring resulted in 91.4% and 98.1% degradations in an as-received glass beaker and in a beaker with a PTFE disk coated on its bottom, respectively. Even for 100 mg/L MO solutions, nearly complete degradation was achieved by magnetic-stirring-stimulated BTO nanoparticles in beakers with the following four kinds of bottom: 97.3% degradation in 30 h for a glass bottom, 97.4% degradation in 20 h for a PTFE coating, 97.9% degradation in 42 h for a Ti coating, and 97.4% degradation in 74 h for an Al₂O₃ coating. Electron paramagnetic resonance (EPR) analyses revealed that the generation of reactive oxygen species (ROS) by magnetic-stirring-stimulated BTO nanoparticles is dramatically affected by the bottom material of beakers. These findings suggest an appealing prospect for BTO nanoparticles to utilize mechanical energy for sustainable water remediation. Full article

In this work, we report a green synthesis of zinc oxide (ZnO) nanoparticles using aqueous and ethanolic extracts of Tradescantia spathacea (purple maguey) as bioreducing and stabilizing agents, which are plant extracts not previously employed for metal oxide nanoparticle synthesis. This method provides an efficient, eco-friendly, and reproducible route to obtain ZnO nanoparticles, while minimizing environmental impact compared to conventional chemical approaches. The extracts were prepared following a standardized protocol, and their phytochemical profiles, including total phenolics, flavonoids, and antioxidant capacity, were quantified via UV-Vis spectroscopy to confirm their reducing potential. ZnO nanoparticles were synthesized using zinc acetate dihydrate as a precursor, with variations in pH and precursor concentration in both aqueous and ethanolic media. UV-Vis spectroscopy confirmed nanoparticle formation, while X-ray diffraction (XRD) revealed a hexagonal wurtzite structure with preferential (101) orientation and lattice parameters a = b = 3.244 Å, c = 5.197 Å. Scanning electron microscopy (SEM) showed agglomerated morphologies, and Fourier transform infrared spectroscopy (FTIR) confirmed the presence of phytochemicals such as quercetin, kaempferol, saponins, and terpenes, along with Zn–O bonding, indicating surface functionalization. Zeta potential measurements showed improved dispersion under alkaline conditions, particularly with ethanolic extracts. This study presents a sustainable synthesis strategy with tunable parameters, highlighting the critical influence of precursor concentration and solvent environment on ZnO nanoparticle formation. Notably, aqueous extracts promote ZnO synthesis at low precursor concentrations, while alkaline conditions are essential when using ethanolic extracts. Compared to other green synthesis methods, this strategy offers control and reproducibility and employs a non-toxic, underexplored plant source rich in phytochemicals, potentially enhancing the crystallinity, surface functionality, and application potential of the resulting ZnO nanoparticles. These materials show promise for applications in photocatalysis, in antimicrobial coatings, in UV-blocking formulations, and as functional additives in optoelectronic and environmental remediation technologies. Full article

Urban water bodies are facing a growing crisis due to contamination from a diverse array of pollutants, encompassing heavy metals, oil and grease, organic and inorganic chemicals, industrial effluents, and pathogenic microorganisms. This study focuses on the burgeoning field of utilizing metal oxide nanoparticles (MONs) as a potential solution to this pressing environmental challenge. The distinctive physicochemical properties of MONs, including their large surface area, catalytic activity, and photocatalytic ability, position them as promising candidates for water purification technologies. This study also comprehensively discusses the sources of urban water pollution and the specific challenges posed by different types of contaminants. A critical evaluation of MONs’ efficacy in removing heavy metals, oil and grease, organic and inorganic chemicals, and industrial pollutants is presented, with a focus on the underlying mechanisms such as adsorption, photocatalysis, and redox reactions. Furthermore, the potential of MONs to neutralize pathogens and microbial contaminants is investigated. While MONs exhibit significant advantages, this study acknowledges the challenges associated with nanoparticle stability, recovery, and potential environmental repercussions. To fully realize the potential of MONs in water treatment, sustained research is imperative to refine treatment processes, develop economically viable strategies, and ensure the long-term sustainability of these technologies in addressing urban water pollution. Full article

This study investigated the enhancement of Cu₂MnSnS₄ (CMTS) thin films’ photocatalytic properties through potassium (K) doping for rhodamine B degradation under visible light. K-doped CMTS films synthesized using spray pyrolysis technology achieved a 98% degradation efficiency within 120 min. The physical property improvements were quantitatively validated through X-ray diffraction (XRD) analysis, which confirmed enhanced crystallinity. Scanning electron microscopy (SEM) revealed significant modifications in surface morphology as a function of potassium content, highlighting its influence on film growth dynamics. Optical characterization demonstrated a pronounced reduction in transmittance, approaching negligible values at 7.5% potassium doping, and a narrowed optical band gap of 1.41 eV, suggesting superior light absorption capabilities. Photocatalytic performance was significantly enhanced, achieving a Rhodamine B degradation efficiency of up to 98% at 7.5% doping. These enhancements collectively improved the material’s light-harvesting capabilities and charge separation efficiency, positioning K-doped CMTS as a highly effective photocatalyst compared to other ternary and quaternary materials. Full article

Zinc oxide (ZnO) is a wide bandgap semiconductor of great scientific and technological interest due to its high exciton binding energy and outstanding structural and optical properties, making it an ideal material for applications in optoelectronics, sensors, and photocatalysis. This study presents the rapid synthesis of highly crystalline ZnO nanostructures using two alternative routes: (1) direct thermal decomposition of zinc acetate and (2) a physical-green route assisted by Mangifera indica extract. Both routes were subjected to identical calcination thermal conditions (400 °C for 2 h), allowing for an objective comparison of their effects on structural, vibrational, morphological, and optical characteristics. X-ray diffraction analyses confirmed the formation of a pure hexagonal wurtzite phase in both samples, highlighting a higher crystallinity index (91.6%) and a larger crystallite size (35 nm) in the sample synthesized using the physical-green route. Raman and FTIR spectra supported these findings, revealing greater structural order. Electron microscopy showed significant morphological differences, and UV-Vis analysis showed a red shift in the absorption peak, associated with a decrease in the optical bandgap (from 3.34 eV to 2.97 eV). These results demonstrate that the physical-green route promotes significant improvements in the structural and functional properties of ZnO, without requiring changes in processing temperature or the use of additional chemicals. Full article

ZnO/SiC nanocomposite materials possess significant potential for various technological fields due to their extraordinary optical, electrical, thermal, and mechanical properties. The synthesis methods, material properties, and diverse applications of ZnO/SiC composites have been systematically explored in this study. The potential application areas of this nanocomposite include their roles in photocatalysis, optoelectronic devices, gas sensors, and photovoltaic systems. The synergetic effects of ZnO and SiC are analyzed to highlight their advantages over their individual components. Future research directions must focus on the remaining challenges to optimize these nanoscale composite materials for industrial and emerging applications. Full article

The pursuit of cleaner environments and healthier ecosystems has driven the development of innovative strategies for detecting and mitigating toxic pollutants. Among emerging nanomaterials, carbon dots (CDs) have gained prominence due to their low toxicity, excellent biocompatibility, high fluorescence efficiency, and environmental sustainability. This review critically analyzes the transformative role of CDs in environmental sensing and remediation. Highlighting their versatile applications, including bioimaging, photocatalysis, and sensitive biochemical sensing, we examine how CDs support the next generation of pollutant detection and degradation technologies, such as contaminant adsorption, membrane filtration, and photocatalytic breakdown. Furthermore, we discuss advances in sensor architectures integrating CDs and outline pathways for their expanded use in environmental monitoring. By mapping the intersection of nanotechnology, environmental science, and sensor innovation, this review anticipates future developments that could redefine pollution control through the strategic deployment of carbon dots. Full article

Advanced oxidation processes are technologies currently being developed and applied to degrade many emerging contaminants that require special attention due to the risks associated with health and the environment. However, the transformation products (TPs) produced by the degradation of these contaminants have attracted little attention from the community regarding their effects on degradation processes, persistence, and environmental toxicity. To present this concern to the scientific community, this article provides data and information that allows us to identify that TPs cannot be pushed to the background or completely ignored in environmental decontamination studies. To this end, heterogeneous photocatalysis was chosen as the primary data collection mechanism due to its interdisciplinary nature. Computational simulation tools, such as Density Functional Theory (DFT), which are widely used to study the properties of materials and contaminants, are very useful and should be applied more frequently to understand the properties of TP. These compounds can interact with photocatalysts and impact the degradation performance of the primary contaminant. Monitoring TPs in degradation reactions is also a challenge due to the lack of analytical standards, the variability of the compounds formed, and the low concentrations produced. The results presented here allow us to conclude that these TPs can affect photocatalytic performance, induce questionable conclusions about their performance, be more toxic than the contaminant of origin, and, above all, contribute relevant information to conclude about the degradation mechanisms. Full article

The sol–gel synthesis of titanium dioxide (TiO₂) nanostructures is investigated in the present work in order to optimize synthesis parameters and enhance the optical properties and cost-effectiveness of the obtained materials. TiO₂ is widely used in photocatalysis, photovoltaics, and environmental applications due to its high stability, tunable band gap, and strong light absorption. The sol–gel method offers a scalable, cost-effective route for producing nanostructured TiO₂, although the precise control over particle morphology remains challenging. For this reason, in the present work, a statistical design of experiments (DOE) approach is employed to systematically refine reaction conditions through the manipulation of precursor concentrations, solvent ratios, and reaction volume. The experimental results obtained indicate that acetic acid is a key catalyst and stabilizing agent, significantly improving nucleation control and particle formation. Moreover, it is also shown that solvent dilution, particularly with acetic acid, leads to the formation of TiO₂ nanorods with enhanced optical properties. Additionally, scanning electron micrographs revealed that controlled synthesis conditions can reduce the particle size distribution and improve structural uniformity. Moreover, X-ray diffraction analyses confirmed the formation of a pure anatase crystalline phase, while ultraviolet–visible spectroscopy analyses indicated the existence of an optimal band gap for photocatalytic applications. Finally, the cost analysis showed that acetic acid-assisted synthesis can reduce production costs and simultaneously maintain high optical properties. Therefore, the present study highlights that proper manipulation and control of reaction conditions during sol–gel syntheses can allow the manufacture of high-performance TiO₂ nanomaterials for advanced technological applications, also providing a foundation for the development of cost-effective materials. Full article

Volatile Organic Compounds (VOCs) pollution poses significant threats to both environmental quality and human health, while conventional purification technologies such as photocatalysis and adsorption exhibit limitations, including low efficiency and high operational costs. This study implements Nano Water Ion Technology (NWIT) for efficient VOCs degradation under ambient conditions (20 °C). Through a customized reaction system, we systematically investigated the degradation performance and mechanistic pathways of NWIT toward representative VOCs (formaldehyde and toluene). Experimental analysis revealed significant correlations between NWIT operation and VOCs degradation: degradation efficiency decreased with elevated airflow velocity, increased with higher relative humidity, and demonstrated concentration-dependent kinetics influenced by ambient VOCs levels. Mechanistic studies identified the co-existing state of O₂ and H₂O as a decisive factor in NWIT efficacy, with non-hydrogen-containing reactive oxygen species exhibiting dominant regulatory roles in VOCs degradation processes, demonstrating superior efficiency enhancement contributions compared to hydrogen-containing reactive oxygen species. Full article

This review provides a descriptive analysis of metformin, highlighting its environmental presence and classification as an emerging contaminant. It examines the risks associated with metformin and evaluates advanced oxidation processes (AOPs) for its degradation, including photolysis, photocatalysis, electrolysis, and ozonation. Metformin, a widely used biguanide for type 2 diabetes, is increasingly detected in aquatic environments due to its incomplete metabolism in humans, raising ecological concerns. While certain AOPs, such as ultraviolet (UV) photocatalysis and ozonation, achieve high degradation rates of 99.9% and 100%, respectively, they produce toxic by-products harmful to aquatic systems. Solar photocatalysis, despite a lower degradation rate (74.22%), stands out for operating without artificial energy and generating fewer hazardous by-products. The review identifies gaps in current degradation strategies and underscores the need for clean, sustainable methods. Future research directions include advancing biological and photocatalytic technologies to improve AOPs’ efficiency while minimizing environmental risks. Full article

Peroxymonosulfate (PMS)-based advanced oxidation technology has emerged as an effective means for removing organic pollutants from water due to its strong oxidizing ability. However, enhancing the activation efficiency of PMS represents a key challenge at present. SrTiO₃, a typical perovskite metal oxide, holds potential in the field of the photocatalytic degradation of pollutants, yet its application is limited by the wide bandgap and fast carrier recombination rates. This study optimized the photocatalytic performance of SrTiO₃ by regulating its electronic structure and optical properties through cobalt (Co) doping. Experimental results (TRPL, TPV, UV–Vis DRS, ESR, etc.) and DFT calculations (GGA-PBE) demonstrated that Co doping shifted the d-band center of SrTiO₃ upwards, optimized the adsorption energy of SO₄⁻, enhanced the sunlight response range, and significantly improved carrier extraction efficiency. Under visible light irradiation, 2,4-dichlorophenol (2,4-DCP) could be effectively degraded within 60 min in a wide pH range. Through Fukui function calculation (B3LYP/6-31G*) and experimental characterization analysis (HPLC-MS and IC), the possible degradation pathways of 2,4-DCP and the mechanism for photocatalysis were investigated. The toxicity analysis (T.E.S.T) confirmed the reduced toxicity of the degradation products of 2,4-DCPs. This study provides a reference for the catalyst design and optimization strategy of PMS-based advanced oxidation technology. Full article