Search Results (18)

This study investigated the use of activated biochar derived from olive stone waste and recycled masonry aggregates in porous mortar mixtures and assessed their behaviour under accelerated carbonation curing conditions. Three mortar mixtures were produced, incorporating 0%, 5%, and 10% activated biochar by volume. The physical, chemical, and mechanical properties of the mortars were analysed, including the compressive strength, flexural strength, water absorption, porosity, and CO₂ capture capacity. Additionally, calorimetry tests were performed on cement pastes with 0%, 0.5%, 1%, 3%, 15%, and 20% activated biochar to evaluate their impact on setting times and ensure compatibility between activated biochar and cement. The results showed that the addition of biochar improved mechanical properties, particularly under accelerated carbonation curing, whereas active biochar (AcB) significantly enhanced the compressive and flexural strengths. Furthermore, biochar incorporation boosted CO₂ capture efficiency, with the 10% biochar mix showing up to 147% higher CO₂ uptake, compared with a control. These findings suggest that activated biochar and recycled masonry aggregates can be effectively utilised to develop sustainable construction materials and thereby contribute to carbon sequestration and the reduction in environmental impacts. This research fills the gaps in the current knowledge on the use of activated biochar from olive stones waste in cement-base materials under accelerated carbonation conditions. Full article

Medicines are pharmaceutical substances used to treat, prevent, or relieve symptoms of different diseases in animals and humans. However, their large-scale production and use worldwide cause their release to the environment. Pharmaceutical molecules are currently considered emerging pollutants that enter water bodies due to inadequate management, affecting water quality and generating adverse effects on aquatic organisms. Hence, different alternatives for pharmaceuticals removal from water have been sought; among them, the use of agro-industrial wastes has been proposed, mainly because of its high availability and low cost. This review highlights the adverse ecotoxicological effects related to the presence of different pharmaceuticals on aquatic environments and analyzes 94 investigations, from 2012 to 2024, on the removal of 17 antibiotics, highlighting sulfamethoxazole as the most reported, as well as 6 non-steroidal anti-inflammatory drugs (NSAIDs) such as diclofenac and ibuprofen, and 27 pharmaceutical drugs with different pharmacological activities. The removal of these drugs was evaluated using agro-industrial wastes such as wheat straw, mung bean husk, bagasse, bamboo, olive stones, rice straw, pinewood, rice husk, among others. On average, 60% of the agro-industrial wastes were transformed into biochar to be used as a biosorbents for pharmaceuticals removal. The diversity in experimental conditions among the removal studies makes it difficult to stablish which agro-industrial waste has the greatest removal capacity; therefore, in this review, the drug mass removal rate (DMRR) was calculated, a parameter used with comparative purposes. Almond shell-activated biochar showed the highest removal rate for antibiotics (1940 mg/g·h), while cork powder (CP) (10,420 mg/g·h) showed the highest for NSAIDs. Therefore, scientific evidence demonstrates that agro-industrial waste is a promising alternative for the removal of emerging pollutants such as pharmaceuticals substances. Full article

Olive mill waste (olive pomace, OP, and olive stone, OS) was used in this work to produce adsorbents for the removal of five phenolic acids typically found in olive mill wastewater. OP and OS were subjected to different treatments (combined or not) that were chemically modified (NaOH) or physically modified by two different methods, incipient wetness impregnation (IWI) and hydrothermal deposition (HD), and even biochar production obtaining a total of 16 materials. The materials were characterized by different analytical techniques such as N₂ absorption, scanning electron microscopy, infrared spectroscopy, and pH zero-potential charge. The mixture of five phenolic acids was used to evaluate in batch conditions the adsorption capacity of the prepared materials. OS chemically modified with IWI (OSM-IWI) and OS biochar with HD (BOS-HD) presented better adsorption capacity at 157.1 and 163.6 mg/g of phenolic acids, respectively, from a total of 200 mg/g. For some materials, the surface area cannot be correlated with adsorption capacity, unlike pHzpc, where high values fit better adsorption rates. The infrared spectroscopy profile indicates the presence of O-H and N-H functional groups and, the last one, red-shifted in the IWI preparation compared to the HD one. In addition to this, the prepared material from olive mill waste can be suitably used for the mixture of phenolic compounds. Full article

In the context of climate change and the circular economy, biochar agricultural and environmental applications have attracted a good deal of attention. Biochar has unique characteristics like surface area, porosity, water-holding capacity, pH, surface charge, and nutrients. This study reviews the biochar production from olive pomace (OP) and olive stone (OS) byproducts, its chemical and physical characterization, and its environmental application. The current review highlights the conditions for biochar production, the effects of pyrolysis temperature, and feedstock type on the physicochemical properties of biochar. High pyrolysis temperature (>500 °C) promotes a high specific surface area, high porosity (especially for OS biochars), and pH as well as the content of ash and fixed carbon, but generates low cation exchange capacity (CEC) and electrical conductivity (EC) and high values of O/C and H/C ratio. OP biochar also presents a high C amount, and ash content, i.e., rich in nutrients and high alkalizing capacity. OP biochar serves as an important source of plant nutrients, especially potassium. After adding both types of biochar, aggregate stability and the amount of water held in soil increase, and bulk density and bioavailability of trace elements decrease. Thus, biochar from olive mill wastes can be a potential plant nutrient reservoir, a good amendment to improve soil properties and long-term carbon sequestration. Results presented in this review can be used to build designer biochars from olive mill wastes to help solve environmental issues (water purification and pollutant remediation) and are suitable for improving soil physical chemistry characteristics and crop growth. Full article

The valorization of untreated municipal waste (MSW) biochar for energetic uses, through its co-gasification with olive stone (OST) biochar under a steam or carbon dioxide atmosphere, was investigated. The experiments were conducted in a fixed bed unit and a thermal analysis–mass spectrometer system. The thermal behavior, reactivity, conversion, product gas composition, syngas yield and energy potential were determined, while the influence of the fuel’s internal structure, chemical functional groups and operating conditions were examined. The concentrations of H₂ and CO₂ in the product gas mixture under a steam atmosphere were increased with steam/biochar ratio, while that of CO was reduced. At a steam/biochar = 3 H₂ yield, the higher heating value and conversion for the OST were 52.8%, 10.8 MJ/m³ and 87.5%; for the MSW, they were 44.4%, 9.9 MJ/m³ and 51.5%, whereas for their blend, they were 50%, 10.6 MJ/m³ and 76.6%, respectively. Under a carbon dioxide atmosphere, the reactivity and conversion of the OST biochar (84%) were significantly higher as compared with the MSW biochar (50%). The higher heating value of the product gas was 12.4–12.9 MJ/m³. Co-gasification of the MSW with OST (in proportions 30:70) resulted in the enhanced reactivity, conversion, syngas yield and heating value of product gas compared with gasification of solely MSW material. Full article

In recent years, biomass has emerged as a promising raw material to produce various products, including hydrocarbons, platform chemicals, and fuels. However, a more comprehensive evaluation of the potential production of desirable value-added products and chemical intermediates is required. For these reasons, this study aimed to investigate the impact of various operating parameters on the pyrolysis of end-of-life olive stone, an agriculture and food industry waste, using a tubular quartz reactor operated at 773 K. The results revealed that the product compositions were comparable under batch or semi-batch nitrogen feeding conditions and with reaction times of 1 or 3 h. The product distribution and composition were significantly influenced by changes in the heating rate from 5 to 50 K min⁻¹, while the effect of changing the biomass particle size from 0.3 to 5 mm was negligible in the semi-batch test. This work provides a comprehensive understanding of the relationship between pyrolysis operational parameters and obtained product distribution and composition. Moreover, the results confirmed the possible exploitation of end-of-life olive stone waste to produce high-added value compounds in the zero-waste strategy and biorefinery concept. Full article

This study assessed the effect of soil amendment with biochar on the production of some Mediterranean crops. Pine-derived biochar (B1) and partially pyrolyzed pine-derived biochar (B2) were used with a dose of 8 L/m² in a corn crop, reporting a production increase of 38–270% over three years with B1, and no effect of B2 due to its poor quality. Olive stone-derived biochar (B3) was used in lavandin and vineyard crops with doses of 0.04–0.9 L/m² and 0.37–2.55 L/m², respectively. An increase of 23–25% in plant volume of lavandin was reported, while the production of grapes per plant was not significantly altered, although it increased by up to 66%. Soil analysis indicated that biochar does not significantly alter soil physicochemical parameters; therefore, biochar may affect plants by altering soil structure and increasing its cation exchange capacity and water management efficiency. Depending on its price, biochar application may be profitable for lavandin and corn crops, with a return-on-investment period ranging from 1 to 4 years. However, the profitability of its use in vineyards is questionable, particularly for the varieties with the lowest market price. Studies examining the economics of biochar application indicate that CO₂ abatement certification may help in covering biochar application costs. Full article

Several biochars were synthesized from olive stones and used as supports for TiO₂, as an active semiconductor, and Pt as a co-catalyst (Pt/TiO₂-PyCF and Pt/TiO₂-AC). A third carbon-supported photocatalyst was prepared from commercial mesoporous carbon (Pt/TiO₂-MCF). Moreover, a Pt/TiO₂ solid based on Evonik P25 was used as a reference. The biochars used as supports transferred, to a large extent, their physical and chemical properties to the final photocatalysts. The synthesized catalysts were tested for hydrogen production from aqueous glycerol photoreforming. The results indicated that a mesoporous nature and small particle size of the photocatalyst lead to better H₂ production. The analysis of the operational reaction conditions revealed that the H₂ evolution rate was not proportional to the mass of the photocatalyst used, since, at high photocatalyst loading, the hydrogen production decreased because of the light scattering and reflection phenomena that caused a reduction in the light penetration depth. When expressed per gram of TiO₂, the activity of Pt/TiO₂-PyCF is almost 4-times higher than that of Pt/TiO₂ (1079 and 273 mmol H₂/g_TiO2, respectively), which points to the positive effect of an adequate dispersion of a TiO₂ phase on a carbonaceous support, forming a highly dispersed and homogeneously distributed titanium dioxide phase. Throughout a 12 h reaction period, the H₂ production rate progressively decreases, while the CO₂ production rate increases continuously. This behavior is compatible with an initial period when glycerol dehydrogenation to glyceraldehyde and/or dihydroxyacetone and hydrogen predominates, followed by a period in which comparatively slower C-C cleavage reactions begin to occur, thus generating both H₂ and CO₂. Full article

To mitigate the environmental harm associated with high-input agriculture, arable farmers are increasingly required to maintain productivity while reducing inputs of synthetic fertilizers. Thus, a diverse range of organic products are now being investigated in terms of their value as alternative fertilizers and soil amendments. This study used a series of glasshouse trials to investigate the effects of an insect frass-based fertilizer derived from black soldier fly waste [HexaFrass™, Meath, Ireland] and biochar on four cereals grown in Ireland (barley, oats, triticale, spelt) as animal feed and for human consumption. In general, the application of low quantities of HexaFrass™ resulted in significant increases in shoot growth in all four cereal species, along with increased foliage concentrations of NPK and SPAD levels (a measure of chlorophyll density). These positive effects of HexaFrass™ on shoot growth were observed, however, only when a potting mix with low basal nutrients was used. Additionally, excessive application of HexaFrass™ resulted in reduced shoot growth and, in some cases, seedling mortality. The application of finely ground or crushed biochar produced from four different feedstocks (Ulex, Juncus, woodchip, olive stone) had no consistent positive or negative effects on cereal shoot growth. Overall, our results indicate that insect frass-based fertilizers have good potential in low-input, organic, or regenerative cereal production systems. Based on our results, biochar appears to have less potential as a plant growth promoting product, but could be used as a tool for lowering whole-farm carbon budgets by providing a simplistic means of storing carbon in farm soils. Full article

Green roofs contribute to more sustainable cities, but current commercial substrates suffer from important limitations. If carefully selected, biochar could serve as a viable option for a more sustainable green roof substrate. We propose a protocol to select an optimal biochar for green roof substrate amendment. Coffee husks, medium-density fiberboard, palm date fronds, and a mixture of waste wood, tree bark, and olive stone kernels are selected as residues for biochar production to develop a selection protocol. The residues are pyrolyzed at 350, 450, 500, and 550 °C in a lab-scale reactor. A pyrolysis temperature of 450 °C is selected for upscaling and is based on biochar yield, pH, salinity, and elemental composition. From evaluating the biochar characteristics after upscaling, it can be concluded that the biochar’s carbonization degree is mainly controlled by pyrolysis temperature, while yield, pH, and salinity are more dependent on the biomass properties. Ultimately, our procedure evaluates the presence of important contaminants, the biochar’s water holding capacity, salinity, pH, and carbonization degree. To validate the developed protocol, plant coverage experiments on green roofs are performed, which are quantified using a novel digital image processing method, demonstrating its efficient use to facilitate future biochar selection in substrates. Full article

Flue dust waste coming from a copper (Cu) smelting company has been valorized using a newly developed metallurgical process with the aim of recovering a dust concentrated in valuable metals, such as lead (Pb) and zinc (Zn), and studying the feasibility of replacing anthracite with biochar as reducing agent. Metallurgical trials using different mixtures of reducing agents have been performed in a furnace at 1400 °C. This furnace employs a high-power thermal plasma (HPTP) system as energy source. Using copper as the base metal, pellets containing a mixture of the waste, different reducing agents, and binder were introduced into the furnace for their dissolution. Recovery yields in the range of 45–85 wt.% for Pb and Zn were obtained in the flue dusts. All the trials proved the effectiveness of the developed process to enrich the flue dusts in valuable metals, including those only using biochar as reducing agent. Further trials will be carried out in order to better control the parameters involved in the metallurgical process developed and improve its efficiency. Full article

Immobilization of nanocatalysts on biochar is receiving unprecedented interest among material and catalysis scientists due to its simplicity, versatility, and high efficiency. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticles loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials, namely bare biochar, copper rich-loaded biochar, and nickel-loaded biochar, were prepared by pyrolysis from olive pit powder particles impregnated first with citric acid (CA) and then with copper and nickel nitrates at 400 °C under nitrogen flow. We employed citric acid in the process in order to examine its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped bimetallic copper/nickel nanoparticles. Large 450–500 nm agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni = 10 molar ratio (B-CA@CuNi_10/1), the bimetallic NPs formed unusual nanoraspberries (174 ± 8 nm in size), which were agglomerates of individual 10–20 nm CuNi_10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be efficiently attracted with a magnet but not B-CA@CuNi_10/1 due to the low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times while still exhibiting the same fast catalytic discoloration performance. This paper stresses the important role of citric acid in shaping bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and in enabling faster catalytic discoloration of organic dye solution. Full article

Cobalt oxide (Co₃O₄) nanoparticles supported on olive stone biochar (OSBC) was used as an efficient sorbent for rifampicin (RIFM) and tigecycline (TIGC) from wastewater. Thermal stabilities, morphologies, textures, and surface functionalities of two adsorbents; OSBC and Co-OSBC were compared. BET analysis indicated that Co-OSBC possesses a larger surface area (39.85 m²/g) and higher pore-volume compared to the pristine OSBC. FT-IR analysis showed the presence of critical functional groups on the surface of both adsorbents. SEM and EDX analyses showed the presence of both meso- and macropores and confirmed the presence of Co₃O₄ nanoparticles on the adsorbent surface. Batch adsorption studies were controlled using a two-level full-factorial design (2^k-FFD). Adsorption efficiency of Co-OSBC was evaluated in terms of the % removal (%R) and the sorption capacity (q_e, mg/g) as a function of four variables: pH, adsorbent dose (AD), drug concentration, and contact time (CT). A %R of 95.18% and 75.48% could be achieved for RIFM and TIGC, respectively. Equilibrium studies revealed that Langmuir model perfectly fit the adsorption of RIFM compared to Freundlich model for TIGC. Maximum adsorption capacity (q_max) for RIFM and TIGC was 61.10 and 25.94 mg/g, respectively. Adsorption kinetics of both drugs could be best represented using the pseudo-second order (PSO) model. Full article

Olive stones are a by-product of the olive oil industry. In this work, the valorisation of olive stones through pyrolysis was attempted. Before pyrolysis, half of the samples were impregnated with sulphuric acid. Pyrolysis was carried out in a vertical tubular furnace with a ceramic support. The pyrolysis conditions assayed were: temperature between 400 and 600 °C, heating ramp between 5 and 20 °C∙min⁻¹, and inert gas flow rate between 50 and 300 mL Ar∙min⁻¹. Among them, temperature was the only parameter that influenced the pyrolysis product distribution. The most suitable temperature for obtaining biochar was 400 °C for both non-treated and pre-treated raw material, while for obtaining bio-oil, it was 600 °C for impregnated olive stones and 400 °C for the raw material. The impregnated olives stones led to bio-oils with much higher amounts of high-added-value products such as levoglucosenone and catechol. Finally, the biochars were impregnated with sulphuric acid and assayed as biocatalysts for the esterification of oleic acid with methanol in a stirred tank batch reactor at 60 °C for 30 min. Biochars from non-treated olive stones, which had lower specific surfaces, led to higher esterification yields (up to 96.2%). Full article

Torrefaction of almond shells and olive stones, which are typically considered agricultural waste in the southern regions of the European Union, was investigated in this work for application as reducing agents in the metallurgical industry. Four different temperatures were tested: 250, 280, 300 and 350 °C. The evolution of the solid yields with the temperature was determined with TGA measurements. This showed that the duration of torrefaction should not exceed 45 min. The kinetic profiles were successfully fitted using the pseudo-first-order rate equation (PFORE). Then, torrefaction for 45 min was systematically carried out at every temperature and for each resource in a laboratory-scale batch device. The raw and torrefied biomasses were characterized using proximate, ultimate and calorific analyses. The carbon/oxygen ratio and the heating values were increased as a result of the torrefaction severity (from 20 MJ/kg for both raw biomasses to 30 MJ/kg at 350 °C). The highest mass losses were obtained at the highest temperature (67.35 and 65.04 %w for almond shells and olive stones, respectively, at 350 °C). The fixed carbon value also increased, being higher than 67 %w for torrefaction at 350 °C. The large-scale torrefaction at 350 °C (45 min) of these biomasses was carried out in a continuous pilot plant. The solids were characterized as well, and their properties were close to those of the biomasses torrefied in the laboratory-scale batch reactor under the same conditions. This thermal treatment provided biochars with all the required properties to be used as reducing materials in metallurgy. Full article