Search Results (386)

Gasification of municipal solid waste and other biogenic residues (e.g., biomass and biowaste) is increasingly recognized as a promising thermochemical pathway for converting non-recyclable fractions into valuable energy carriers, with applications in electricity generation, district heating, hydrogen production, and synthetic fuels. This paper provides a comprehensive analysis of major gasification technologies, including fixed bed, fluidized bed, entrained flow, plasma, supercritical water, microwave-assisted, high-temperature steam, and rotary kiln systems. Key aspects such as feedstock compatibility, operating parameters, technology readiness level, and integration within circular economy frameworks are critically evaluated. A comparative assessment of incineration and pyrolysis highlights the environmental and energetic advantages of gasification. The valorization pathways for main product (syngas) and by-products (syngas, ash, tar, and biochar) are also explored, emphasizing their reuse in environmental, agricultural, and industrial applications. Despite progress, large-scale adoption in Europe is constrained by economic, legislative, and technical barriers. Future research should prioritize scaling emerging systems, optimizing by-product recovery, and improving integration with carbon capture and circular energy infrastructures. Supported by recent European policy frameworks, gasification is positioned to play a key role in sustainable waste-to-energy strategies, biomass valorization, and the transition to a low-emission economy. Full article

The sustainable utilization of solid waste is crucial for environmental protection. This work investigates the fabrication of foamed ceramics from Cr slag and municipal solid waste incineration (MSWI) fly ash, focusing on the effects of three inhibitors—NH₂SO₃H, ZnO·TiO₂, and (NH₄)₂HPO₄—on material properties and Cr leaching behavior. Experimental analysis, chemical thermodynamic calculations, and material characterization were all employed. Results show that the prepared foamed ceramics meet the JG/T 511-2017 standard for building materials, exhibiting excellent physical properties but significant Cr leaching. Among the inhibitors, (NH₄)₂HPO₄ with a molar ratio of n(P)/n(Cr) = 1 shows the best performance, achieving a bulk density of 205 kg/m³, compressive strength of 0.850 MPa, Cr leaching concentration of 188 μg/L, and a 70.0% of Cr leaching inhibition rate. The improvement is attributed to the AlPO₄ formation that enhancing the strength, and Ca₂P₂O₇ that stabilizing Cr during sintering. This work provides a feasible method for the safe resource utilization of Cr-containing waste. Full article

Biodrying and composting are aerobic processes to treat and stabilize organic solid waste, but biodrying involves a shorter process time and does not require the addition of water. The resulting biodried material (BM) is mainly used as an energy source in cement production or in municipal solid waste incineration with energy recovery, but when obtained from agricultural or agroindustrial organic waste, it could also be used as a soil amendment, such as compost (CO). In this study, the phytotoxicity of BM compared to CO, both made from organic wastes (orange peel, mulch and grass), was evaluated on seed germination and growth (for 90 days) of lettuce (Lactuca sativa L.) seedlings on treatments prepared from mixtures of BM and soil, soil (100%) and a mixture of CO and soil. The germination index (GI%) was higher for BM extracts (200 g/L) than for CO extracts (68% vs. 53%, respectively). According to their dry weight, lettuce grew more on the CO mixture (16.5 g) than on the BM (5.4–7.4 g), but both materials far exceeded the soil values (0.15 g). The absence of phytotoxicity suggests that BM acts as a soil amendment, improving soil structure and providing nutrients to the soil. Therefore, biodrying is a quick and low-cost bioprocess to obtain a soil improver. Full article

The co-disposal of municipal solid waste incineration fly ash (MSWI-FA) in cement kilns is an effective method for managing incineration by-products in China. However, the presence of heavy metals in MSWI-FA raises environmental concerns. This study analyzed the Cu, Zn, Cd, Pb, Cr, and Ni concentrations in MSWI-FA from 11 representative facilities across China and assessed the efficacy of a three-stage water washing process for Cl and heavy metal removal. The results revealed significant regional variations in heavy metal content that were strongly correlated with surface soil levels, with Zn, Pb, and Cu exhibiting the highest concentrations. Elemental correlations, such as Cu-Pb and Zn-Cd synergies and Cd-Ni antagonism, suggest common waste sources and temperature-dependent volatilization during incineration. The washing process (solid–liquid ratio = 1:10) achieved 97.1 ± 2.0% Cl removal, reducing residual Cl to 0.45 ± 0.32%, but demonstrated limited heavy metal elimination (10.28–19.38% efficiency), resulting in elevated concentrations (32.5–60.8% increase) due to 43.4 ± 9.2% mass loss. Notably, the washing effluents exceeded municipal wastewater discharge limits by up to 52-fold for Pb and 38-fold for Cd, underscoring the need for advanced effluent treatment. To mitigate environmental risks, the addition of washed MSWI-FA in cement kilns should be restricted to ≤0.5%, with Cd content prioritized in pre-disposal assessments. This study provides actionable insights for optimizing MSWI-FA co-processing while ensuring compliance with ecological safety standards. Full article

The accelerated industrialization in China has precipitated a dramatic surge in solid waste generation, causing severe land resource depletion and posing substantial environmental contamination risks. Simultaneously, the cement industry has become characterized by the intensive consumption of natural resources and high carbon emissions. This review aims to investigate the current technological advances in utilizing industrial solid waste for cement production, with a focus on promoting resource recycling, phase transformations during hydration, and environmental management. The feasibility of incorporating coal-based solid waste, metallurgical slags, tailings, industrial byproduct gypsum, and municipal solid waste incineration into active mixed material for cement is discussed. This waste is utilized by replacing conventional raw materials or serving as active mixed material due to their content of oxygenated salt minerals and oxide minerals. The results indicate that the formation of hydration products can be increased, the mechanical strength of cement can be improved, and a notable reduction in CO₂ emissions can be achieved through the appropriate selection and proportioning of mineral components in industrial solid waste. Further research is recommended to explore the synergistic effects of multi-waste combinations and to develop economically efficient pretreatment methods, with an emphasis on balancing the strength, durability, and environmental performance of cement. This study provides practical insights into the environmentally friendly and efficient recycling of industrial solid waste and supports the realization of carbon peak and carbon neutrality goals. Full article

The resource utilization potential and environmental impact of fly ash from municipal solid waste incinerators (MSWIs) have attracted wide attention. In this study, four MSWIs in Hangzhou, Zhejiang Province were selected to systematically evaluate the effects of different incinerator types and flue gas deacidification processes on fly ash’s oxide and heavy metal components and their temporal changes as well as conduct risk assessment. The results showed that the contents of MgO, Al₂O₃, SiO₂, and Fe₂O₃ in the grate furnace fly ash were significantly lower than those in the fluidized bed fly ash, but the compressive strength of its fly ash was high. Chemicals added during the flue gas deacidification process such as CaO and NaHCO₃ significantly affected the contents of CaO and Na₂O. In addition, heavy metals such as Cu, Mn, Cr, and Ni were mainly distributed in the fluidized bed fly ash, while heavy metals such as Pb and Cd were mainly collected in the grate furnace fly ash. The concentrations of various components in the fly ash fluctuated but were not significant under different time dimensions. Risk assessment indicated that heavy metals such as Cd, Pb, and Sb posed a high risk. This study is expected to provide theoretical support for the safe management and resource utilization of fly ash. Full article

Municipal solid waste (MSW) and refuse-derived fuel (RDF) incineration generate over 20 million tons of residues annually in the EU. These include bottom ash (IBA), fly ash (FA), and air pollution control residues (APCr), which pose significant environmental challenges due to their leaching potential and hazardous properties. While these residues contain valuable metals and reactive mineral phases suitable for carbonation or alkaline activation, chemical, techno-economic, and policy barriers have hindered the implementation of sustainable, full-scale management solutions. Accelerated carbonation technology (ACT) offers a promising approach to simultaneously sequester CO₂ and enhance residue stability. This review provides a comprehensive assessment of waste incineration residue carbonation, covering 227 documents ranging from laboratory studies to field applications. The analysis examines reactor designs and process layouts, with a detailed classification based on material characteristics, operating conditions, investigated parameters, and the resulting pollutant stabilization, CO₂ uptake, or product performance. In conclusion, carbonation-based approaches must be seamlessly integrated into broader waste management strategies, including metal recovery and material repurposing. Carbonation should be recognized not only as a CO₂ sequestration process, but also as a binding and stabilization strategy. The most critical barrier remains chemical: the persistent leaching of sulfates, chromium(VI), and antimony(V). We highlight what we refer to as the antimony problem, as this element can become mobilized by up to three orders of magnitude in leachate concentrations. The most pressing research gap hindering industrial deployment is the need to design stabilization approaches specifically tailored to critical anionic species, particularly Sb(V), Cr(VI), and SO₄²⁻. Full article

Flotation was investigated to treat incineration fly ash with diesel, kerosene, TX-100, or SDS as a collector and methyl isobutyl carbinol (MIBC) or 2-Octyl alcohol as a frother. Fly ash was separated into light and residual materials. Comparison of yield, carbon and sulfur removal showed that kerosene and MIBC showed the best performance. The results revealed that flotation was a method that could simultaneously achieve the removal of organics and S-containing compounds. Specifically, approximately 7.63–9.45% of the total mass was collected as light material, which was enriched with organic carbon. Contents of organic carbon reached 14.35 wt%–14.56 wt% in the light materials from those of 2.74 wt%–3.52 wt% in the original fly ash. Elemental analysis further proved that sulfur was also accumulated in light material. Approximately 78.84–81.69% of the organic carbon and 80.47–82.66% of the sulfur were removed. Decarbonization was primarily achieved through the flotation of organic materials, while desulfurization resulted from both flotation and the dissolution of soluble salts. Furthermore, the contents of the chloride and heavy metals in the residual fly ash also decreased. Particle size analysis showed that flotation was effective in the removal of smaller particles, and those particles were also rich in heavy metals. Overall, by selecting the right collector and frother, flotation was also able to reduce the leaching toxicity of heavy metals. The residual fly ash was safe for further disposal. Organic carbon, sulfur and heavy metals were accumulated in the light materials, which accounted for less than 10% of the original mass. The portion of fly ash needing further treatment was therefore greatly reduced. Full article

The stable control of the main steam flow rate (MSFR) can effectively improve the waste combustion efficiency and energy utilization, reduce environmental pollution, and is crucial for promoting the sustainable development of municipal solid waste incineration (MSWI). Developed countries benefit from stable municipal solid waste (MSW) composition, enabling advanced automated combustion control. However, in developing countries, fluctuating waste composition and calorific value cause frequent disturbances, limiting the use of foreign control methods. Therefore, MSFR control technologies suited to developing countries are crucial. This study proposes a two-layer intelligent control method, consisting of an optimization setting layer and a loop control layer. The optimization layer uses a steam flow prediction model (OPTICS and RBF) and an improved antlion optimizer (IALO) for manipulated variable setpoints. The control layer applies reinforcement learning (actor–critic) to fine-tune PI controller parameters. Experimental results show that the proposed method adaptively adjusts manipulated variables, ensuring MSFR control within the target range and maintaining efficient, stable MSWI operation. Full article

This review thoroughly evaluates gasification as a transformative alternative to conventional methods for managing municipal solid waste (MSW), highlighting its potential to convert carbonaceous materials into syngas for energy and chemical synthesis. A comparative evaluation of more than 350 papers and documents demonstrated that gasification is superior to incineration and pyrolysis, resulting in lower harmful emissions and improved energy efficiency, which aligns with sustainability goals. Key operational findings indicate that adjusting the temperature to 800–900 °C leads to the consumption of CO₂ and the production of CO via the Boudouard reaction. Air gasification produces syngas yields of up to 76.99 wt% at 703 °C, while oxygen gasification demonstrates a carbon conversion efficiency of 80.2%. Steam and CO₂ gasification prove to be effective for producing H₂ and CO, respectively. Catalysts, especially nickel-based ones, are effective in reducing tar and enhancing syngas quality. Innovative approaches, such as co-gasification, plasma and solar-assisted gasification, chemical looping, and integration with carbon capture, artificial intelligence (AI), and the Internet of Things (IoT), show promise in improving process performance and reducing technical and economic hurdles. The review identifies research gaps in catalyst development, feedstock variability, and system integration, emphasizing the need for integrated research, policy, and investment to fully realize the potential of gasification in the clean energy transition and sustainable MSW management. Full article

This work focuses on the use of municipal waste incineration bottom ash (MSWI) for the development and production of products suitable for use as construction products. The generation of these ashes is increasing every year due to the incineration of municipal waste. There are currently three incineration plants operating in major cities in Lithuania. The non-hazardous bottom ash remaining from the incineration process is stored in dedicated sorting and aging sites until it is used as an inert form of aggregate for the installation of road foundations. However, it has been observed that these ashes have a tendency to bind and cement when exposed to atmospheric precipitation at the storage site. Based on this characteristic, it was decided in this study to use alkaline activation of the ash to accelerate the bonding process and to create a dense, non-porous composite concrete structure. This activation method is known to create another problem during ash bonding, where the presence of metallic aluminum particles in the ash leads to the release of hydrogen gas and makes the structure of the cured samples porous. For the purposes of the study, it was decided to create a completely different mixture structure and not to use additional water in the mixtures tested. A very low water/solids ratio (W/S) of <0.08 was used for the alkaline activation of the mixtures. All the water required for ash activation was obtained from sodium silicate and sodium hydroxide solution. Metakaolin waste (MKW) was used to adjust the SiO₂/Na₂O/Al₂O₃ ratio of the mixtures. Vibro-pressing was used to form and increase the density of the samples. And for the formation of the concrete structure, 0/4 fraction sand was used as aggregate. The final alkali-activated sample obtained had properties similar to those of the very widely used vibro-pressed cementitious paving tiles and did not exhibit hydrogen evolution during alkali activation due to the very low W/S ratio. The best results were achieved by samples with a highest compressive strength of 40.0 MPa and a tensile strength of 5.60 MPa, as well as a density of 1950 kg/m³. It is believed that this alkaline activation and vibro-pressing method can expand the use of MSWI ash in the development of building products. Full article

Carbon monoxide (CO) is a toxic pollutant emitted by municipal solid waste incineration (MSWI), which has a strong correlation with dioxins. In terms of the sustainable development of an ecological environment, CO emission concentration is strictly controlled by the environmental departments of various countries in the world. The construction of its prediction model is conducive to pollution reduction control. The MSWI process is affected by multi-factors such as MSW component fluctuation, equipment wear and maintenance, and seasonal change, and has complex nonlinear and time-varying characteristics, which makes it difficult for the CO prediction model based on offline historical data to adapt to the above changes. In addition, the continuous emission monitoring system (CEMS) used for conventional pollutant detection has unavoidable misalignment and failure problems. In this article, a novel prediction model of CO emission from the MSWI process based on semi-supervised concept drift (CD) detection in kernel feature space is proposed. Firstly, the CO emission deep prediction model and the kernel feature space detection model are constructed based on offline batched historical data, and the historical data set for the real-time construction of the pseudo-labeling model is obtained. Secondly, the drift detection for the CO emission prediction model is carried out based on real-time data by using unsupervised kernel principal component analysis (KPCA) in terms of feature space. If CD occurs, the pseudo-label model is constructed, the pseudo-truth value is obtained, and the drift sample is confirmed and selected based on the Page–Hinkley (PH) test. If no CD occurs, the CO emission concentration is predicted based on the historical prediction model. Then, the updated data set of the CO emission prediction model and kernel feature space detection is obtained by combining historical samples and drift samples. Finally, the offline history model is updated with a new data set when the preset conditions are met. Based on the real data set of an MSWI power plant in Beijing, the validity of the proposed method is verified. Full article

This study aims to obtain findings on the internal water behavior, the presence of water channels, and the degree of washout due to rainfall infiltration in Japanese municipal solid waste (MSW) final disposal sites. Electrical resistivity tomography (ERT) monitoring and undistributed waste sampling for X-ray computed tomography (X-ray CT) analysis were conducted in the field. The study sites were targeted at Site A, which is mainly composed of non-combustible residues, and Site B, which is mainly composed of incineration ash. The time-dependent resistivity distributions obtained from real-time ERT monitoring were effective for us to understand the water content distribution after water infiltration during water injection tests. As a result, the global flow behavior and the local water channel flow were determined. In addition, X-ray CT analysis of the undisturbed waste samples obtained from the sites clarified the different pore structures, indicating the possibility of more advanced washing out at Site A than at Site B. Furthermore, the soil cover layer and gas extraction wells had a significant effect on the resistivity structure with respect to water flow behavior. Since soil cover layer and gas extraction wells are significant factors affecting waste stabilization by washout, it is suggested that these factors should be considered in the design and maintenance of landfills. Full article

Renewable energy sources are presented as a key solution to today’s energy needs, but they also generate waste that can have a negative impact on the environment. In particular, fly ash from the incineration of municipal solid waste (MSW), classified as hazardous by European regulations, is often deposited in landfills due to its lack of usefulness. This research proposes its valorisation in geopolymers, combining it with mining to create a sustainable material with a high industrial waste content. Firstly, all the wastes involved were characterised, which allowed for the development of a high-quality geopolymer from mining residue activated with 5% NaOH. This material was enriched with up to 50% fly ash (in increasing percentages) with the aim of making it inert, retaining it in the geopolymer matrix, and observing its effect on the final material. The physical and mechanical properties of the geopolymers obtained were evaluated, demonstrating that they do not produce contaminating leachates. The results indicate the feasibility of developing a geopolymer with up to 20% fly ash, obtaining a building material comparable to traditional ceramics, suitable for commercialisation, with a lower environmental impact and in line with the principles of the circular economy. Full article

Textile recycling approaches require input material streams of defined purity. Establishing sorting facilities and defining viable sorting fractions for efficient subsequent recycling necessitates knowledge on the composition and material content of the textiles to be processed. Subsequently, this information is crucial for the implementation of a sustainable circular economy for textiles. This study presents the results of a comprehensive waste textile sampling and characterisation along with data on the quantities and composition of waste textiles in Vienna in 2022. The data reveals that only 28% of the 19,975 t of waste textiles generated end up in separate collection, of which a significant amount goes to the international market. However, the results regarding the fibre composition show that textiles from mixed municipal solid waste and separate collection are very similar. Cotton fibres accounted for approx. half of the fibre mass from non-complex textiles, with 9328 t overall (6776 t in the mixed municipal solid waste and 2522 t in separate collection). A further analysis regarding fibre blends found that a total of 6275 t of single-fibre materials and 5132 t of two-fibre materials were present. This reveals great potential for using this waste stream in fibre-to-fibre recycling processes. Collecting accurate data on this waste stream enables sorters and recyclers to tailor their processes to the expected input material. By increasing the amount of recycled materials, the share of incinerated or landfilled textiles will decrease, which in turn will have a positive impact on the environment. However, further research in textile identification and material separation as well as regulations to keep these materials in a sustainable closed loop are required. Full article