Search Results (52)

Septic wastewater, or septage, represents a specific type of wastewater with a high concentration of organic matter and significant variability in composition, which places increased demand on its treatment. With the increasing pressure for decentralized solutions for small areas with no established sewage infrastructure, technologies that can ensure stable operation of the treatment plant are coming to the fore. This paper compares the technologies used for septic wastewater treatment, i.e., sequencing batch reactor (SBR), membrane bioreactor (MBR), and aerobic granular sludge reactor (AGS). For the AGS technology, a trial run of a selected wastewater collection plant is carried out. Full article

Tire microplastics (TMPs) are a widespread pollutant with growing concern due to their diverse sources, persistence, and potential risks to the environment and human health. This study investigated the impact of TMPs (50–500 mg/L) on the sludge structure, activity, and extracellular polymeric substance (EPS) dynamics in granular sequencing batch reactors (GSBRs) under continuous aeration (CA) and intermittent aeration (IA) conditions. Increased TMP concentration reduced granule size and increased the specific surface area under CA, but under IA, it increased granule size and lowered specific surface area. Total EPS declined as TMP concentration increased in both aeration regimes, but the reduction was more pronounced under CA. Protein levels in the soluble EPS fraction were consistently higher during IA than CA across all GSBRs. Aeration regimes had contrasting effects on EPS polysaccharides, as TMP dose increased; polysaccharide content increased during IA and decreased during CA. During CA, TMP presence enhanced dehydrogenase activity to over five times that of the control, while during IA, activity remained stable despite TMP addition. Overall, biomass under IA showed greater tolerance to TMP stress than CA, as evidenced by enhanced granulation, stable dehydrogenase activity, and preserved EPS. Full article

This study compared the effectiveness of the Sequencing Batch Biofilter Granular Reactor (SBBGR) plant with and without the integration of ozone (BIO-CHEM process) in the remediation of medium-aged landfill leachate. Special attention is given to the removal of per- and polyfluoroalkyl substances (PFAS) as a group of bioaccumulative and persistent pollutants. The findings highlight the high SBBGR performance under biological process only for key wastewater contaminants, with 82% for chemical oxygen demand (COD), 86% for total nitrogen, and 98% for ammonia. Moderate removal was observed for total (TSS) and volatile (VSS) suspended solids (41% and 44%, respectively), while phosphorus and colour removal remained limited. Remarkably, the SBBGR process achieved complete removal of long-chain PFAS, while its performance declined for shorter-chain PFAS. BIO-CHEM process significantly improved COD (87.7%), TSS (84.6%), VSS (86.7%), and colour (92–96%) removal. Conversely, ozonation led to an unexpected increase in the concentrations of several PFAS in the effluent, suggesting ozone-induced desorption from the biomass. SBBGR treatment was characterised by a low specific sludge production (SSP) value, i.e., 5–6 times less than that of conventional biological processes. SSP was further reduced during the application of the BIO-CHEM process. A key finding of this study is a critical challenge for PFAS removal in this combined treatment approach, different from other ozone-based methods. Full article

Wastewater treatment plants (WWTPs) face increasing pressure to handle higher volumes of water due to climate change causing storm surges, which current infrastructure cannot handle. Aerobic granular sludge (AGS) is a promising alternative to activated sludge systems due to their improved settleability property, lowering the land footprint and improving efficiency. This research investigates the optimisation of a lab-scale sequencing batch reactor (SBR) into a continuous flow reactor through mathematical modelling, sensitivity analysis, and a computational fluid dynamic model. This is all applied for the future goal of scaling up the model designed to a full-scale continuous flow reactor. The mathematical model developed analyses microbial kinetics, COD degradation, and mixing flows using Reynolds and Froude numbers. To perform a sensitivity analysis, a Python code was developed to investigate the stability when influent concentrations and flow rates vary. Finally, CFD simulations on ANSYS Fluent evaluated the mixing within the reactor. An 82% COD removal efficiency was derived from the model and validated against the SBR data and other configurations. The sensitivity analysis highlighted the reactor’s inefficiency in handling high-concentration influents and fast flow rates. CFD simulations revealed good mixing within the reactor; however, they did show issues where biomass washout would be highly likely if applied in continuous flow operation. All of these results were taken under deep consideration to provide a new reactor configuration to be studied that may resolve all these downfalls. Full article

This study examines the effects of polyester and denim microfibers (MFs) on aerobic granular sludge (AGS) over a 42-day period. Treatment performance, granulation, and microbial community changes were assessed at 0, 10, 70, 210, and 1500 MFs/L. Reactors with 70 MFs/L achieved rapid granulation and showed improved settling by day 9, while 0 and 10 MFs/L reactors showed delayed granule formation, which was likely due to limited nucleation and weaker shear conditions. Severe clogging and frequent maintenance occurred at 1500 MFs/L. Despite > 98% MF removal in all reactors, treatment performance declined at higher MF loads. Nitrogen removal dropped from 93% to 68%. Phosphate removal slightly increased in reactors with no or low microfiber loads (96–99%), declined in reactors with 70 or 210 MFs/L (92–91%, 89–88%), and dropped significantly in the reactor with1500 MFs/L (86–70%, p < 0.05). COD removal declined with increasing MF load. Paracoccus (denitrifiers) dominated low-MF reactors; Acinetobacter (associated with complex organic degradation) and Nitrospira (nitrite-oxidizing genus) were enriched at 1500 MFs/L. Performance decline likely stemmed from nutrient transport blockage and toxic leachates, highlighting the potential threat of MFs to wastewater treatment and the need for upstream MF control. Full article

The widely utilized TiO₂ nanoparticles (NPs) tend to accumulate in wastewater and affect microbial growth. This work investigated the impacts of prolonged TiO₂ NP addition to filamentous aerobic granular sludge (AGS) using two identical sequencing batch reactors (SBRs, R1 and R2). R1 (the control) had no TiO₂ NP addition. In this reactor, filamentous bacteria from large AGS grew rapidly and extended outward, the sludge volume index (SVI₃₀) quickly increased from 41.2 to 236.8 mL/g, mixed liquid suspended solids (MLSS) decreased from 4.72 to 0.9 g/L, and AGS disintegrated on day 40. Meanwhile, the removal rates of COD and NH₄⁺-N both exhibited significant declines. In contrast, 5–30 mg/L TiO₂ NPs was added to R2 from day 21 to 100, and the extended filamentous bacteria were effectively controlled on day 90 under a 30 mg/L NP dosage, leading to significant reductions in COD and NH₄⁺-N capabilities, particularly the latter. Therefore, NP addition was stopped on day 101, and AGS became dominant in R2, with an SVI₃₀ and MLSS of 48.5 mL/g and 5.67 g/L on day 130. COD and NH₄⁺-N capabilities both increased to 100%. Microbial analysis suggested that the dominant filamentous bacteria—Proteobacteria, Bacteroidetes, and Acidobacteria—were effectively controlled by adding 30 mg/L TiO₂ NPs. XRF analysis indicated that 11.7% TiO₂ NP accumulation made the filamentous bacteria a framework for AGS recovery and operation without NPs. Functional analysis revealed that TiO₂ NPs had stronger inhibitory effects on nitrogen metabolism compared to carbon metabolism, and both metabolic pathways recovered when NP addition was discontinued in a timely manner. These findings offer critical operational guidance for maintaining the stable performance of filamentous AGS systems treating TiO₂ NP wastewater in the future. Full article

Industrial activated sludge plants in many sectors, including the dairy industry, face sludge separation problems caused by sludge bulking. Aerobic granular sludge (AGS) could be a solution by forming well-settling granules. The key to successful granulation is the microbial selection of slow-growing glycogen-accumulating organisms (GAOs) by introducing an anaerobic feeding/reaction step. The objective of the current study was to investigate the impact of two slow feeding strategies to achieve granulation in existing sequencing batch reactors treating real dairy wastewater, by microbial selection only. The first strategy consisted of slow 90 min mixed feeding. The second strategy combined 45 min static and 45 min mixed feeding to build up a substrate gradient. The feeding strategies did not affect the effluent quality, but significantly impacted the sludge morphology, settling properties, and microbial community composition. Mixed feeding led to filamentous overgrowth by Thiothrix species, up to 45% abundance, and deteriorating settling, with sludge volume index (SVI) values up to 125 mL/g. In contrast, static feeding yielded densified sludge with SVI values below 45 mL/g and up to 35% GAO abundance. In conclusion, the results show successful granulation when using a simple static slow feeding mode, which could benefit the industrial application of AGS technology. Full article

In recent years, there has been an increase in the emission of tire wear particle (TWP) microplastics from wastewater treatment plants into the environment. The aim of this study was to determine the effect of TWPs in wastewater flowing into a biological reactor on the transcription of the 16S rRNA gene and the key genes responsible for nitrogen metabolism, amoA, nirK and nosZ, in aerobic granular sludge. The laboratory experiment was carried out in sequencing aerobic granular sludge reactors operated in an 8 h cycle into which TWP microplastics were introduced with municipal wastewater at a dose of 50–500 mg TWPs/L. The ammonia removal rate and the production of oxidized forms of nitrogen increased with the TWP dose. Gene transcript abundance analysis showed that the presence of rubber and substances leached from it promoted the activity of ammonium-oxidizing bacteria (160% increase), while the transcription of genes related to denitrification conversions was negatively affected. The activity of nitrite reductase gradually decreased with increasing TWP concentration in wastewater (decreased by 33% at 500 mg TWPs/L), while nitric oxide reductase activity was significantly inhibited even at the lowest TWP dose (decreased by 58% at 500 mg TWPs/L). The data obtained indicate that further studies are needed on the mechanisms of the effects of TWPs on the activities of the most important groups of microorganisms in wastewater treatment to minimize the negative effects of TWPs on biological wastewater treatment. Full article

Aerobic granular sludge (AGS) is a promising technology for wastewater treatment. Granules have a compact microbial structure and a high potential for pollutant removal. Despite its advantages, the impact of microplastics (MPs) on AGS remains poorly understood, posing a potential risk to the stability and efficiency of biological wastewater treatment processes. This study investigates the effects of polyethylene terephthalate (PET) MPs on AGS structure and extracellular polymeric substance (EPS) composition, providing new insights into the interaction between MPs and AGS. Four granular sequencing batch reactors (GSBRs) were operated with varying concentrations of PET MPs in the influent wastewater (0, 1, 10, 50 mg/L). Key findings include MP-induced changes in granule size distribution, with an increase in smaller granules (<90 µm) observed in reactors exposed to PET MPs. EPS concentrations (51–77 mg/L) exhibited significant differences among reactors, with notable shifts in protein (PN) and polysaccharide (PS) fractions. A higher PET MP dose resulted in an increased PN/PS ratio (from 1.96 to 5.40) and elevated hydrophobicity of AGS. These changes suggest that MPs can alter AGS structure and EPS composition, potentially affecting granule stability and treatment performance. This study provides novel evidence on the disruptive effects of MPs in wastewater treatment systems, emphasizing the need to address MP pollution in the context of biological treatment processes. The results contribute to a deeper understanding of the interactions between MP and AGS and form the basis for strategies to mitigate their adverse effects. Full article

The work presents the concept of aerobic granular sludge (AGS) and its potential for wastewater treatment. The work also evaluates the condition of the SBR (Sequencing Batch Reactor) type of municipal wastewater-treatment plant (WWTP) after its reconstruction into a system with AGS. The WWTP parameters achieved before and after reconstruction were compared. Operational measurements of the process during the individual phases of the treatment process showed a balanced concentration profile of the monitored parameters in the span of the semicontinuous cycle. Laboratory tests showed that the sludge from the WWTP has nitrification and denitrification rates comparable to the rates achieved for flocculent sludge, and it is also comparable to the nitrification and denitrification rates of AGS with size of granules below 400 µm. Despite the fact that complete sludge granulation was not achieved, the results measured at the WWTP confirmed the advantages of the AGS concept. Neither anaerobic nor anoxic conditions were identified in the SBR during the individual phases of operation, yet high removal efficiencies of ammonia and nitrate nitrogen and orthophosphate phosphorus were achieved. The concentration of ammonia and nitrate nitrogen at the WWTP effluent was below 5 mg/L, and the concentration of phosphorus was below 0.5 mg/L. Full article

This study investigates the densification/granulation of activated sludge with poor settleability, treating real industrial wastewater from a tank truck cleaning company. The wastewater is low in nutrients, acidic in nature, and high and variable in chemical oxygen demand (COD, ranging from 2770 mg·L⁻¹ to 14,050 mg·L⁻¹). A microbial selection strategy was applied to promote slow-growing glycogen-accumulating microorganisms (GAO) by the implementation of an anaerobic feast/aerobic famine strategy in a sequencing batch reactor (SBR). After 60 to 70 days, the uptake of carbon during the anaerobic phase exceeded 80%, the sludge morphology improved, and the sludge volume index (SVI) dropped below 50 mL·g⁻¹. 16S rRNA gene sequencing showed the enrichment of the GAOs Defluviicoccus and Candidatus Competibacter. Stable sludge densification was maintained when using a constant organic loading rate (OLR) of 0.85 ± 0.05 gCOD·(L·d)⁻¹, but the sludge quality deteriorated when switching to a variable OLR. In view of the integration of densified/granular sludge in a membrane bioreactor configuration, the filtration properties of the densified SBR sludge were compared to the seed sludge from the full-scale plant. The densified sludge showed a significantly lower resistance due to pore blockage and a significantly higher sustainable flux (45 vs. 15 L·(m²·h)⁻¹). Full article

This study aimed to investigate the influencing factors and characteristics of granule morphology through approximately 500 d of long-term monitoring of two types of anaerobic–aerobic phosphorus-accumulating organism (PAO) and anaerobic–anoxic denitrifying PAO (DPAO) sequencing batch reactors (SBRs). The results show that granules were present in the DPAO SBR and PAO SBR after 200 d and 250 d of operation, respectively. The average diameters of the granules were 2.2 ± 0.7 mm in the DPAO SBR and 0.4 ± 0.3 mm in the PAO SBR, respectively. The DPAO granular sludge contained rod-shaped microorganisms, whereas the PAO granular sludge contained cocci-type microorganisms. A precipitated core consisting of hydroxyapatite was found in the DPAO granules. A comparative analysis conducted under various operating conditions revealed that the availability and type of the electron acceptors (EAs) may have a significant impact on granulation. This observation suggests that the presence and diversity of EAs are crucial factors for the development of different granule sizes and morphologies. Full article

This study evaluates the potential to synthesize an adsorbent for wastewater remediation applications from an anaerobic digestion by-product synthesized using biomaterials and a less energy-intensive process. The synthesized sludge-based granular activated carbon (GAC) was used to adsorb Cr(VI) and Cd(II) in a batch reactor stirred for 24 h at 25 °C. The surface chemistry of the material was assessed porosity with BET, SEM for morphology, EDS-XRF for elemental analysis, and functional groups on these materials using FTIR and TGA for thermal profile. S_BET of the SAC was discovered to be 481.370 m²/g with a V_T of 0.337 cm³/g, respectively 9.02 and 2.23 times greater than raw sludge. The modification to SAC shows a dramatic increase in performance from 40% to 98.9% equilibrium adsorption rate. The maximum or equilibrium removal (99.99%) of Cr(VI) and Cd(II) was achieved by 0.8 and 1.4 g SAC dosage, respectively. Thus, it can be concluded that activation of sewage sludge was effective in enhancing the surface area and pore volume which made it suitable for AMD remediation application. Full article

It has been proven that the biocenosis of microalgae and bacteria improves the chemical properties of biomass for its use in anaerobic digestion. However, this anaerobic digestion can be limited by the strong, compact, and complex structure of granulated biomass. Therefore, there is a need to search for an effective method for microalgal–bacterial granular sludge pretreatment, which has not been undertaken in previous scientific works. In this study, ultrasonic pretreatment was used to determine the effects of sonication on anaerobic digestion efficiency. Anaerobic digestion was performed in batch respirometric reactors. It was found that the ultrasonic pretreatment enhanced the biomass solubility; thus, the organic matter concentration increased more than six times compared to the variant without pretreatment. The study showed a positive effect of sonication on the kinetics of the anaerobic process and methane production. The highest methane yield was found in the variants in which the ultrasonication lasted from 150 s to 200 s, and this yield was from 534 ± 16 mL CH₄/g VS to 561 ± 17 mL CH₄/g VS. The data analysis confirmed strong correlations between the pretreatment time, the amount of biogas and methane production, and the gross energy gain. The highest net energy output and net energy gain were obtained for 150 s of sonication, and, respectively, were 4.21 ± 0.17 Wh/g VS and 1.19 ± 0.18 Wh/g VS. Full article

A sequencing batch reactor (SBR) inoculated with activated sludge and bioaugmented with a dye-decolorizing yeast strain—Yarrowia lipolytica (HOMOGST27AB) was assembled to form yeast-bioaugmented aerobic granular sludge (AGS). The bioaugmented AGS-SBR was operated for the treatment of synthetic saline wastewater (12 g L⁻¹) intermittently fed with a reactive textile dye (Navy Everzol ED) at 25, 15, and 7.5 mg L⁻¹. Dye degradation did not occur, although some dye adsorbed to the granules. AGS-SBR performance in removing carbon and nitrogen was good and was not affected by the dye addition. Bioaugmentation with the yeast Y. lipolytica (HOMOGST27AB) occurred with success, proved by sequencing samples from granules throughout the reactor operation. The AGS core microbiome gathered essentially microorganisms from the Proteobacteria and Bacteroidetes phyla. The microbial profile showed a dynamic microbiome established at Phase I of the operation, with a high decrease in the abundance of Ignavibacterium from the initial biomass to the granules formed and an increase in Actinobacteria, Cytophagia, Flavobacteria, and Alphaproteobacteria in the remaining phases of the bioreactor operation. Full article