Search Results (2,981)

This study examined the effects of phosphoric acid (H₃PO₄), polyimide (PI), and lubricants (MoS₂, graphite) on the phase stability, microstructure, and magnetic performance of Fe-5.0 wt.%Si soft magnetic composites (SMCs). Warm compaction (≤550 °C) and annealing at 700 °C were applied to samples prepared under a full factorial design. X-ray diffraction confirmed stable α-Fe(Si) phases without secondary phases. SEM and TEM–EDS revealed interfacial insulating layers mainly composed of Si-O, with localized phosphorus and carbon. Additive composition strongly influenced magnetic and physical properties. Increasing H₃PO₄ and PI reduced the density from 7.50 to 7.27 g/cm³ and lowered the permeability (from 189 at 1 kHz to 156), due to thicker interparticle layers that restricted metallic contact and domain wall motion. In contrast, Q-values rose significantly with frequency: for H₃PO₄ 0.25 wt.% + PI 0.25 wt.% + graphite 0.3 wt.%, Q increased from 0.39 (1 kHz) to 2.91 (10 kHz), reflecting effective eddy current suppression. Lubricant type further influenced performance: graphite consistently outperformed MoS₂, with 0.3 wt.% graphite providing the best balance of high density, permeability, and a frequency-stable Q-value. Overall, Fe-5.0 wt.%Si performance is governed not by bulk phase changes but by the trade-off between densification and insulation at particle interfaces. The optimal combination of low H₃PO₄ and PI with 0.3 wt.% graphite offers practical guidelines for designing high-frequency, high-efficiency motor materials. Full article

In the field of shipping engineering, guide walls serve as core flow-guiding structures for river regulation and waterway maintenance. Their structural stability, construction efficiency, and maintainability directly determine shipping safety and construction costs. Currently, guide walls in mountainous rivers predominantly utilize cast-in-place monolithic structures, which suffer from issues such as complicated construction, high cement consumption, and poor adaptability. This study proposes a novel prefabricated reinforced guide wall, consisting of a base plate, prefabricated concrete units, intra-layer bolts, and inter-layer reinforcement bars, and develops a nonlinear numerical framework, integrating contact mechanics, metal plasticity, and finite element analysis to investigate the mechanical behavior of the proposed wall structure under hydraulic loads. The results show that the prefabricated reinforced guide wall exhibits stable stress and deformation responses and maintains reliable inter-layer stability. Benefiting from its hollow prefabricated configuration, which replaces part of the concrete with rockfill, the proposed system substantially reduces cement demand and supports low-carbon and sustainable construction. This study provides both theoretical insights and engineering evidence for the safe, efficient, and sustainable application of prefabricated reinforced guide walls in mountainous river locks. Full article

The long-term viscoelastic behaviour of epoxy matrices in Carbon Fibre-Reinforced Polymer (CFRP) tendons can lead to creep strains which must be accurately quantified to improve the current necessarily conservative design guidelines for bridge applications. However, the task of experimentally capturing such strains—typically in the range of 0.05%—requires sensors with reliable long-term accuracy and precision. This study investigates creep in CFRP tendons subjected to sustained tensile loading at 80% (for 7 days) and 88% (for 22 h) of their ultimate tensile strength. Four strain sensing techniques were employed to capture the creep strains of the CFRP tendons: bonded metal foil strain gauges, a contact extensometer, Digital Image Correlation, and distributed fibre optic strain sensing. This work precisely quantifies—for the first time in CFRP creep testing—the influence of experimental artefacts on the performance of the strain sensors, including test rig movement, temperature sensitivity, and localised surface inhomogeneities. Results reveal significant measurement distortions: the extensometer recorded strain increases of 250% during tendon slip, while distributed fibre optics detected localised strain peaks reaching 150% of the surface average. These findings demonstrate that sensor-induced noise can substantially contaminate creep strain data, underscoring the critical need for rigorous experimental protocols and thorough sensor validation in CFRP creep studies. Full article

Heavy metal pollution remains one of the major environmental challenges due to the persistence and toxicity of metals such as Pb(II). This study investigates the potential of natural diatomite from Mugaldzhar, Kazakhstan, as a low-cost and sustainable sorbent for lead removal from aqueous solutions. The effects of key parameters, including sorbent dosage, particle size, contact time, temperature, and initial Pb(II) concentration, were systematically examined. Adsorption experiments revealed a maximum adsorption capacity of 74.9 mg/g at 45 °C and an initial Pb(II) concentration of 800 mg/L. The adsorption behavior followed the pseudo-second-order kinetic model, indicating a chemisorption mechanism, while isotherm analysis showed a transition from Langmuir to Freundlich type with increasing temperature. Thermodynamic data confirmed the spontaneous and endothermic nature of the process. These results demonstrate that unmodified natural diatomite exhibits high efficiency for Pb(II) removal, emphasizing its suitability as an eco-friendly and cost-effective material for water purification and environmental remediation. Full article

Aluminum, one of the most abundant metals found on our planet, plays a crucial role in manufacturing as it is lightweight and resistant to corrosion and has excellent machinability. Of its numerous alloys, Al6061 is one of the most popular alloys used for CNC machining due to its superior mechanical and processing properties. This paper aims to investigate the impact of machining under dry and wet machining conditions. Correspondingly, the impact of dry machining on the material removal rate (MRR) and surface roughness (Ra) of Al6061 was evaluated. Machining was performed on a CNC Lathe. Two rods of Al6061 were used, and a dynamometer was attached to them to measure the radial, thrust, and tangential forces. In wet machining, the coolant used was a mixture of cutting oil and water. Different RPMs, feed rates, and depths of cut were entered into the machine as parameters. And the optimum parameters where found. This research utilizes particle swarm optimization approaches in order to evaluate optimal parameters, in contrast to traditional measurement methods such as contact profilometry or cutting force measurement. The results indicate that surface roughness rises with the depth of cut and feed rate. Ra rises by about 200% when dry machining is conducted at 0.05 mm/rev with increased depths of cut from 0.5 mm to 2.5 mm. In wet machining, the rise is much smaller, approximately 67% at 0.05 mm/rev and 30% at 0.25 mm/rev. Wet machining always produces more finished surfaces, decreasing Ra by 22–25% over dry machining. Wet machining is therefore better suited for achieving high-quality surface finish in Al6061 machining. Full article

Lead (Pb) is a highly toxic heavy metal frequently found in industrial wastewater, posing serious risks to both human health and the environment. In this study, a porous geopolymer synthesized from fly ash, metakaolin, and red mud was evaluated for Pb(II) removal via batch adsorption experiments under varying pH, dosage, contact time, temperature, and initial concentration. The synthesized material exhibited a favorable mesoporous structure, with a BET surface area of 42.05 m² g⁻¹ and an average pore width of 6.26 nm, making it suitable for heavy metal uptake. Adsorption kinetics followed the pseudo-second-order model (R² = 0.9993), while the Langmuir isotherm (R² ≈ 0.999) best described the equilibrium data, indicating monolayer chemical adsorption as the dominant mechanism, with a maximum capacity of 74.26 mg g⁻¹ at 318 K. Thermodynamic analyses confirmed that the adsorption was spontaneous (ΔG° < 0), endothermic (ΔH° > 0), and accompanied by increased entropy (ΔS° > 0). Desorption and regeneration tests revealed EDTA to be a more effective agent than HNO₃, maintaining a reuse efficiency of 81.35% after four cycles. These results highlight the potential of waste-derived porous geopolymers as regenerable, low-cost, and efficient adsorbents for lead removal. Full article

Digital Image Correlation systems are increasingly being used for non-contact measurement of deformation and strain in sheet metal components. However, the accuracy of such measurements can be significantly affected by various external and system-related factors. If these are not properly considered, substantial errors may be introduced. In this study, a short and longer flat sheet specimen were clamped in a vise to investigate how overhang and clamping stability influence the accuracy of the measured deformation fields. Two different measurement volumes were also evaluated to assess their effect on the results. These factors were evaluated through targeted experiments, and the resulting data were analyzed and interpreted. Based on the findings, recommendations were formulated to enhance the reliability of Digital Image Correlation measurements in both laboratory and industrial environments. Full article

Metal-free aminobenzoic acid-derived Schiff bases are attractive antimicrobial leads because their azomethine (–C=N–) functionality enables tunable electronic properties and target engagement. We investigated whether halogenation on the phenolic ring would modulate the redox behavior and enhance antibacterial potency, and hypothesized that heavier halogens would favorably tune physicochemical and electronic descriptors. We synthesized three derivatives (SB-3/Cl, SB-4/Br, and SB-5/I) and confirmed their structures using FTIR, ¹H- and ¹³C-NMR, UV-Vis, and HRMS. For SB-5, single-crystal X-ray diffraction and Hirshfeld analysis verified the intramolecular O–H⋯N hydrogen bond and key packing contacts. Cyclic voltammetry revealed an irreversible oxidation (aminobenzoic ring) and, for the halogenated series, a reversible reduction associated with the imine; peak positions and reversibility trends are consistent with halogen electronic effects and DFT-based MEP/LHS descriptors. Antimicrobial testing showed that SB-5 was selectively potent against Gram-positive aerobes, with low-to-mid micromolar MICs across the panel. Among anaerobes, activity was more substantial: Clostridioides difficile was inhibited at 0.1 µM, and SB-3/SB-5 reduced its sporulation at sub-MICs, while Blautia coccoides was highly susceptible (MIC 0.01 µM). No activity was detected against Gram-negative bacteria at the tested concentrations. In the fungal assay, Botrytis cinerea displayed only a transient fungistatic response without complete growth inhibition. In mammalian cells (HeLa), the compounds displayed clear concentration-dependent behavior. Overall, halogenation, particularly iodination, emerges as a powerful tool to couple redox tuning with selective Gram-positive activity and a favorable cellular tolerance window, nominating SB-5 as a promising scaffold for further antimicrobial optimization. Full article

Psittacine bornavirus type-4 (PaBV-4) causes proventricular dilatation disease and death among diverse birds, most notably caged parrots and related species, with no known cure or vaccine. Infected birds can shed virus in fecal matter, urine, and feather dander but it is unknown how well PaBV-4 survives outside of the host. This study focused on assessing the persistence of PaBV-4 in common environmental situations. The presence of viral RNA was examined in aqueous solutions at varying temperatures and recovery from typical avian husbandry materials (plastic, wood, metal, and cloth). Viral RNA persistence in aqueous samples was found to be 3 weeks at 37 °C, 2 months at 24 °C (room temperature), and 3 months at 4 °C. Viral RNA was also recovered from plastic and metal surfaces up to 72 h after inoculation. Also examined were disinfection protocols comparing coverage versus contact time for a reduction in viral RNA. Complete coverage by the disinfecting agent was more important for preventing recovery of viral RNA. Additionally, PaBV-4 RNA was transferable by paper towel. These results provide the first evidence of the robust nature of PaBV-4 in an aqueous environment and show that cleaning protocols need to be carefully curated to limit possible viral spread. Full article

The cutting process is accompanied by complex electrical phenomena, which are particularly evident in narrow cutting clearances. To further explore the laws of electrical phenomena in the capillary of the cutting zone, this paper uses a Faraday collector with an external bias electric field to investigate the electrical phenomena in the narrow slit of the cutting zone under different cutting parameters and when different tool and workpiece materials are combined. The results show that there is a stable and continuous electrical phenomenon in the cutting contact area, and the emission intensity of charged particles when cutting insulating materials is significantly higher than that of metals. The emission intensity of negative ions is higher than that of positive ions. The electrical and mechanical properties of materials have a significant impact on the electrical phenomena in the cutting zone. In addition, it was found that there is a linear relationship between the electrical phenomena in the cutting zone and the cutting parameters. Finally, based on the morphology of the capillaries in the cutting zone, the self-excited electric field intensity generated in it during the cutting process was estimated. Full article

This study presents evaluation of biochar derived from silkworm cocoons for the adsorption of organic and inorganic contaminants from rainwater. The material was characterised using BET surface area analysis, scanning electron microscopy (SEM), and the point of zero charge (pH_PZC). The prepared biochar exhibited a well-developed surface area and demonstrated adsorption capacity toward both heavy metals and benzotriazole. The model rainwater was prepared by spiking real rainwater samples with Cu(II), Ni(II), Zn(II) ions, and benzotriazole (BT). Adsorption experiments were carried out under laboratory conditions to evaluate the effects of contact time, pH, and sorbent dosage. The experimental data were fitted to pseudo-first-order and pseudo-second-order kinetic models, as well as Langmuir/and Freundlich isotherms. The results showed that the adsorption of Cu(II) followed the Langmuir/Freundlich model, while the adsorption of Ni(II) benzotriazole was more consistent with the Freundlich model. Adsorption kinetics were best described by the pseudo-second-order model. The highest removal efficiencies were observed for Cu(II) (96%) and Ni(II) (88.8%), while Zn(II) removal was limited. Benzotriazole was also effectively adsorbed (97%), rapid adsorption occurred mainly within the first minute. Overall, the study highlights the selective adsorption behaviour of silkworm cocoon biochar and provides a comparative insight into the removal of organic and inorganic pollutants using a waste-derived adsorbent with surface properties comparable to those of activated carbon. Full article

The increasing demand for enhanced wear resistance and mechanical integrity in tooling applications has driven the development of advanced surface engineering strategies for high-alloy steels. Böhler K390 MICROCLEAN, a powder-metallurgical V–Cr–Mo–W cold work tool steel with high vanadium content, features a composite metal matrix–carbide microstructure, consisting of uniformly distributed coarse vanadium carbides and finer carbides (M₇C₃, M₆C/MC) embedded in a ferritic matrix. This study investigated the effects of non-melting laser surface treatment (LST) applied to both as-received and bulk heat-treated K390 specimens. Microstructural characterization using SEM, EBSD, XRD, and EDX revealed the formation of a hardened surface layer comprising a structureless mixture of ultrafine-grained martensite and retained austenite, localized around vanadium carbides. Lattice parameter analysis and Williamson–Hall evaluation demonstrated increased carbon content, lattice distortion, and crystallite size reduction, contributing to high dislocation density (6.4 × 10¹⁴ to 2.6 × 10¹⁵ m⁻²) and enhanced hardness. Microhardness was increased by up to 160% compared to the initial state (reaching 835–887 HV₂₀), and dry-sliding testing showed up to 3.94 times reduced volume loss and decreased friction coefficients. Wear occurred via the formation and delamination of thin oxide tribo-layers, which enhanced the wear behavior. The combined approach of bulk heat treatment followed by LST produced a graded microstructure with superior mechanical stability, offering clear advantages for extending tool life under severe contact loads in stamping and forming operations. Full article

Today, the engineering of load-bearing bone tissue after severe trauma still relies on metal-based (Ti, CoCrMo alloys or stainless steel) permanent implants. Such artificial scaffolds are typically applied in the body and come into direct contact with the recipient’s cells, whose adhesion affects the patient’s implant acceptance or rejection. The present study aims to create a nano-rough texture by means of ultra-short femtosecond laser (fs)-induced periodicity in the form of laser induced periodic surface structures (LIPSS) on the surface of a stainless steel implant model, which is additionally functionalized via magnetron-sputtering with a thin Cu layer, thus providing the as-created implants with a stable antimicrobial interface. Calcium phosphate (CaP) crystal growth was additionally applied due to the strong bioactive interface bond that CaPs provide to the bone connective tissue, as well as for the strong interface bond they create between the artificial implant and the surrounding bone tissue, thereby stabilizing the implanted structure within the body. The bioactive properties in the as-created antimicrobial hybrid topographical design, achieved through femtosecond laser-induced nanoscale surface structuring and micro-sized CaP crystal growth, have the potential for subsequent practical applications in bone tissue engineering. Full article

Metathesis reactions of Ag[C(CN)₃] with anhydrous YbCl₃ dissolved in water combined with stoichiometric amounts of the alkali-metal salts A[C(CN)₃] (A = Na or K) yield the non-isotypic tetragonal compounds NaYb[C(CN)₃]₄ (P4/nnc with a = 1188.37(9) pm, c = 1232.41(9) pm) and KYb[C(CN)₃]₄ (P4/nbm with a = 1179.26(9) pm, c = 668.73(5) pm). Both crystal structures contain a three-dimensional framework (Niggli formula: $\begin{array}{c}3\\ \infty \end{array}${(Yb[C(CN)₃]_8/2)⁻}) with Yb³⁺ in square antiprismatic coordination of terminal nitrogen atoms (d(Yb–N) = 241–242 pm) from eight planar star-shaped tricyanomethanide anions [C(CN)₃]⁻. The Na⁺ or K⁺ cations occupy vacancies, which provide them with a tetrahedral coordination sphere of nitrogen (d(Na–N) = 239 pm vs. d(K–N) = 276 pm) from four [C(CN)₃]⁻ anions. This difference results from secondary contacts with the central carbon atoms (d(Na–C) = 361 pm vs. d(K–C) = 367 pm) of four different [C(CN)₃]⁻ units, which do not contribute to NaYb[C(CN)₃]₄, but effectuate a lot in the case of KYb[C(CN)₃]₄. The Raman spectrum recorded for NaYb[C(CN)₃]₄ corroborates the presence of a pseudo-D_3h-symmetric tricyanomethanide anion [C(CN)₃]⁻ and the absence of water. Full article

Ionic Polymer–Metal Composites (IPMCs) are promising electroactive polymers for artificial muscles, as their bending motion depends on the induced current—greater current leads to greater bending. While conventional IPMCs use cation exchange membranes, this study explores IPMCs containing both immobile positive and negative charges, resembling real muscle tissue. Considering that an IPMC consists of an ion-exchange membrane sandwiched between two thin metal coatings serving as electrodes, we found that (i) improving the contact between the metal coating (electrode) and the ion exchange membrane is an effective way to enhance current induction. Achieving tight electrode membrane contact can drastically increase the induced current by up to four orders of magnitude, and even samples that previously showed no current induction can exhibit measurable current after improvement. (ii) Doping with mobile ions is another well-known method of enhancing IPMC current. However, we found that simply introducing dopants into the IPMC body is not effective; the choice of dopant is crucial. In this work, we identified silver ions as effective dopants for enhancing current induction. Considering that real muscles consume oxygen for activation, we also attempted to supply oxygen to the IPMC surface. We confirmed that (iii) supplying oxygen to the IPMC surface is another effective means of enhancing current induction, which in turn resulted in a significant improvement in IPMC bending performance. Full article