Search Results (177)

This study developed sustainable biocomposites composed of polylactic acid (PLA) and surface-treated pineapple core powder (PACP), fabricated via extrusion and fused deposition modelling (FDM). PACP loadings of 1–3 vol% were combined after chemical modification with NaOH and silane to improve interfacial bonding. Particle morphology showed increased porosity and surface roughness following treatment. The melt flow index (MFI) increased from 31.56 to 35.59 g/10 min at 2 vol% PACP, showing improved flowability. Differential scanning calorimetry (DSC) showed the emergence of cold crystallization (T_cc ~121 °C) and an increase in crystallinity from 35.7% (neat PLA) to 47.3% (2 vol% PACP). Thermogravimetric analysis showed only slight decreases in T₅ and T_max, showing the thermal stability. The mechanical testing of extruded filaments showed increased modulus (1463 to 1518 MPa) but a decrease in tensile strength and elongation. For the 3D-printed samples, elongation at break increased slightly at 1–2 vol% PACP, likely because of the improvement in interlayer fusion. Though, at 3 vol% PACP, the mechanical properties declined, consistent with filler agglomeration observed in SEM. Overall, 2 vol% PACP offered the optimal balance between printability, crystallinity, and mechanical performance. These results reveal the possibility of PACP as a value-added biowaste filler for eco-friendly PLA composites suitable for extrusion and 3D printing applications. Full article

Green soybeans, or edamame (Glycine max L. Merril), serve as a superior source of phytochemicals and other nutritive substances and are commonly used as ingredients and additives in food products due to their polyphenols’ functional properties and antioxidant activity. Hence, it is very important to use a process to extract compounds with functional roles from plants as efficiently as possible. In this study, we sought to identify the optimal conditions for extracting genistein, belonging to the aglycone subgroup of isoflavones, from edamame using the cold plasma (CP) and enzyme method. Additionally, the impact of various drying techniques (spray-drying and freeze-drying) and storage conditions on the crude genistein extract powder was evaluated. The findings showed that the maximum values for the total phenolic content (TPC), total flavonoid content (TFC), and genistein (22.5 ± 0.23 mg of gallic acid equivalents (GAE)/100 g; 15.3 ± 0.13 mg of catechin equivalents (CAE)/100 g; and 12.6 ± 0.10 mg/100 g, respectively) were achieved under optimal pretreatment conditions using a CP gas flow rate of 5 L/min for 30 min, followed by enzymatic treatment at a specific enzyme concentration of 2.0% (v/v) for 240 min of incubation. Moreover, a scanning electron microscopy (SEM) analysis demonstrated that the CP and enzyme treatment induced significant structural changes, as evidenced by the presence of deeper pores on the surface of the powder granules. Spray-drying demonstrated a superior efficacy compared to freeze-drying for encapsulating the crude isoflavone extract. This study’s results also demonstrated that storage at 4 °C significantly stabilized the TPC, TFC, and genistein content and the antioxidant activity while preserving the physical properties (solubility and color) of the crude extract powder for up to 45 days. In summary, cold plasma pretreatment and enzymatic treatments offer practical solutions by enhancing the efficiency of non-thermal extraction processes, thereby increasing the yield of bioactive compounds, maintaining quality, and diminishing reliance on traditional, harsh methods. The elevated genistein content in the crude extract powder indicates its prospective application as a functional ingredient in various food and nutraceutical contexts. Full article

Objectives: The purpose of this study is to quantitatively evaluate the combined effects of sports massage, blood flow restriction (BFR), and cold therapy on quadriceps recovery in mixed martial arts (MMA) athletes following eccentric exercise, focusing on muscle biomechanical properties, pain, and strength. Methods: This randomized, single-blind clinical trial involved 36 men and women MMA-trained participants, divided into three groups: massage (n = 12) received massage, BFR/cool (n = 12) received combined BFR and cooling, and control (n = 12) received passive rest as a control. The fatigue protocol involved MMA fighters performing five sets of plyometric jumps on a 50 cm box until exhaustion, with 1-min breaks between sets. After that, the massage group received a 20-min massage overall using standardized techniques; BFR/cool underwent a 20-min alternating blood flow restriction (200 mmHg) and cooling treatment with ice bags on the quadriceps; and the final group served as the control group with passive rest and no intervention. Participants were assessed four times—before exercise, immediately after exercise, 24 h post-exercise (after two recovery sessions), and 48 h post-exercise (after four recovery sessions)—for perfusion unit (PU), muscle elasticity, pressure pain threshold (PPT), reactive strength index (RSI), and total quality recovery (TQR). Results: The statistical analysis revealed significant effects of both massage and BFR/cooling interventions across key recovery outcomes, with large effect sizes for time-related changes in RSI (p < 0.0001; η² = 0.87), elasticity (p < 0.0001; η² = 0.84), and PPT (p < 0.0001; η² = 0.66). Notably, post-exercise 48 h values for RSI, elasticity, PU, and TQR were significantly improved in both the massage and BFR/cool groups compared to control (p < 0.05)), while no significant group differences were observed for PPT. Conclusions: The study concludes that both massage and combined blood flow restriction with cooling interventions significantly enhance post-exercise recovery—improving muscle perfusion, elasticity, reactive strength, and perceived recovery—compared to passive rest. Full article

The development of alternative energies has become a concern for all countries to ensure domestic energy supply and provide environmental friendliness. One of the providential alternative energies is biodiesel. Biodiesel, commonly stated as fatty acid alkyl ester (FAAE), is a liquid fuel intended to substitute petroleum diesel. Nevertheless, implementation of pure biodiesel is not recommended for conventional diesel engines. It holds poor values of cold flow properties, as the effect of high saturated FAAE content contributes to this constraint. Several processes have been proposed to enhance cold flow properties of biodiesel, but this work focuses on the skeletal isomerization process. This process rearranges the skeletal carbon chain of straight-chain FAAE into branched isomeric products to lower the melting point, related to the good cold flow behavior. This method specifically requires an acid catalyst to elevate the isomerization reaction rate. And then, sulfated tin(IV) oxide emerged as a solid superacid catalyst due to its superiority in acidity. The results of biodiesel isomerization over this catalyst and its modification with iron had not satisfied the expectation of high isomerization yield and significant CFP improvement. However, they emphasized that the skeletal isomers demonstrated minimum impact on biodiesel oxidation stability. They also affirmed the role of an acid catalyst in the reaction mechanism in terms of protonation, isomerization, and deprotonation. Furthermore, the metal promotion was theoretically necessary to boost the catalytic activity of this material. It initiated the dehydrogenation of linear hydrocarbon before protonation and terminated the isomerization by hydrogenating the branched carbon chain after deprotonation. Finally, the overall findings indicated promising prospects for further enhancement of catalyst performance and reusability. Full article

Salinity and clay mineral types have been shown to influence the migration and settlement efficiency of microplastics (MPs) under restrictive experimental conditions. However, current research is limited to deep trenches or laboratory conditions, and studies in the semi-enclosed sea area of the continental shelf are still lacking. We investigated the effects of bottom seawater salinity and clay mineral types on MPs distribution in surface sediments using the western part of the North Yellow Sea as an example, where current conditions are complex and salinity changes rapidly over short distances. Under detection conditions with a minimum detection limit of 10 μm, the abundance range of MPs in the investigated sea area reached 24–1134 items/(g dry weight). The distribution of MPs was in good agreement with the isohaline of the bottom seawater, and MPs tended to converge in the high salinity area. However, there is an exceptional case in which the temperature and salinity difference caused by the cold water mass can create a frontal flow that blocks the transport of terrigenous materials to the middle of the cold water mass. This phenomenon causes MPs to settle at the edge of the cold water mass. A significant positive correlation exists between montmorillonite with expansive properties and fragment MPs and MPs with particle size > 100 μm, which have a larger surface area (p < 0.05). The negative charges on the surface of MPs and clay minerals are neutralized, promoting the heterogeneous aggregation between clay minerals and MPs and accelerating the sedimentation process of MPs in the ocean. This is another important reason for the accumulation of MPs in the high-salinity region. This study provides a basis for pollution prevention and control of MPs in the shallow sea, supplying new insights into the effects of bottom seawater salinity and clay mineral type on the distribution of MPs. Full article

Raynaud’s Phenomenon (RP), characterized by episodic reductions in peripheral blood flow, leads to significant discomfort and functional impairment. Existing therapeutic strategies focus on pharmacological treatments, external heat supplementation and exercise-based rehabilitation, but fail to address biomechanical contributions to vascular dysfunction. We introduce a computational approach rooted in topological transformations of hand prehension, hypothesizing that specific hand postures can generate transient geometric structures that enhance thermal and hemodynamic properties. We examine whether a flexed hand posture—where fingers are brought together to form a closed-loop toroidal shape—may modify heat transfer patterns and blood microcirculation. Using a combination of heat diffusion equations, fluid dynamics models and topological transformations, we implement a heat transfer and blood flow simulation to examine the differential thermodynamic behavior of the open and closed hand postures. We show that the closed-hand posture may preserve significantly more heat than the open-hand posture, reducing temperature loss by an average of 1.1 ± 0.3 °C compared to 3.2 ± 0.5 °C in the open-hand condition (p < 0.01). Microvascular circulation is also enhanced, with a 53% increase in blood flow in the closed-hand configuration (p < 0.01). Therefore, our findings support the hypothesis that maintaining a closed-hand posture may help mitigate RP symptoms by preserving warmth, reducing cold-induced vasoconstriction and optimizing peripheral flow. Overall, our topologically framed approach provides quantitative evidence that postural modifications may influence peripheral vascular function through biomechanical and thermodynamic mechanisms, elucidating how shape-induced transformations may affect physiological and pathological dynamics. Full article

Energy storage stations (ESSs) need to be charged and discharged frequently, causing the battery thermal management system (BTMS) to face a great challenge as batteries generate a large amount of heat with a high discharge rate. Supercritical carbon dioxide (SCO₂) is considered a promising coolant because of its favorable properties, including non-flammability, high dielectric strength and low cost for the BTMS. The heat of a battery can be absorbed to a great extent if there is a small temperature rise because as the fluid temperature approaches a pseudo-critical temperature, the specific heat capacity of SCO₂ reaches its peak. In this study, a periodic model of the unit BTMS is established, and a numerical simulation is implemented to investigate the effects of different boundary conditions on the heat dissipation of a battery pack. The flow and heat transfer characteristics of SCO₂ in the liquid cold plate (LCP) of a battery pack with an extreme discharge rate are revealed. The results show that SCO₂ is more preferably used as a coolant compared to water in the same conditions. The maximum temperature and the temperature difference in the battery pack are reduced by 19.22% and 79.9%, and the pressure drop of the LCP is reduced by 40.9%. In addition, the heat transfer characteristic of the LCP is significantly improved upon increasing the mass flow rate. As the operational pressure decreases, the pressure drops of SCO₂ decrease in the LCP. Overall, the maximum temperature and the temperature difference in the battery pack and the pressure drops of the LCP can be effectively controlled by using a coolant made out of SCO₂. This study can provide a reference for the design of BTMSs in the future. Full article

Ground-source heat pump (GSHP) systems with medium-depth and deeply buried pipes in cold regions are highly important for addressing global climate change and the energy crisis because of their efficient, clean, and sustainable energy characteristics. However, unique geological conditions in cold climates pose serious challenges to the heat transfer efficiency, long-term stability, and adaptability of systems. This study comprehensively analyses the effects of various factors, including well depth, inner-to-outer tube diameter ratios, cementing material, the thermal conductivity of the inner tube, the flow rate, and the start–stop ratio, on the performance of a medium-depth coaxial borehole heat exchanger. Field tests, numerical simulations, and sensitivity analyses are combined to determine the full-cycle thermal performance and heat-transfer properties of medium-depth geological formations and their relationships with system performance. The results show that the source water temperature increases by approximately 4 °C and that the heat transfer increases by 50 kW for every 500 m increase in well depth. The optimization of the inner and outer pipe diameter ratios effectively improves the heat-exchange efficiency, and a larger pipe diameter ratio design can significantly reduce the flow resistance and improve system stability. When the thermal conductivity of the cementing cement increases from 1 W/(m·K) to 2 W/(m·K), the outlet water temperature at the source side increases by approximately 1 °C, and the heat transfer increases by 13 kW. However, the improvement effect of further increasing the thermal conductivity on the heat-exchange efficiency gradually decreases. When the flow rate is 0.7 m/s, the heat transfer is stable at approximately 250 kW, and the system economy and heat-transfer efficiency reach a balance. These findings provide a robust scientific basis for promoting medium-deep geothermal energy heating systems in cold regions and offer valuable references for the green and low-carbon transition in building heating systems. Full article

Background/Objectives: Colorectal cancer (CRC) remains a leading cause of cancer-related mortality, necessitating the development of effective preventive strategies. Fenugreek (Trigonella foenum-graecum) possesses well-documented pharmacological properties; however, its chemopreventive potential in colorectal cancer (CRC) remains unexplored. This study evaluates the efficacy of methanolic fenugreek seed extract (FSE) in an azoxymethane (AOM)-induced murine colorectal cancer (CRC) model, focusing on the modulation of oxidative stress, regulation of biomarkers, induction of apoptosis, and maintenance of epithelial integrity. Methods: FSE was extracted using cold maceration (yield: 24%) and analyzed by gas chromatography–mass spectrometry (GC-MS), identifying 13 bioactive compounds, including benzene, 1,3-dimethyl-; 1,3-cyclopentadiene, 5-(1-methylethylidene)-; o-Xylene; benzenepropanoic acid, 3,5-bis(1,1-dimethylethyl)-4-hydroxy-; and benzene, 1,2,3-trimethyl-. All 13 compounds identified were matched with the NIST library with high confidence. Molecular docking was used to assess the interactions of FSE bioactives with E-cadherin–β-catenin complexes. Swiss albino mice received an FSE pre-treatment before AOM induction and continued this treatment three times weekly for 21 weeks. Key assessments included survival analysis, body weight changes, serum biomarker levels (GGT, 5′-NT, LDH), antioxidant enzyme activities (SOD, CAT, GPx1, MDA), reactive oxygen species (ROS) quantification, apoptosis detection via flow cytometry, and immunofluorescence-based evaluation of E-cadherin dynamics. Results: FSE improved survival rates, mitigated AOM-induced weight loss, and dose-dependently reduced serum biomarker levels. Antioxidant enzyme activity was restored, while MDA levels declined. A dose-dependent increase in ROS facilitated apoptosis, as confirmed by flow cytometry (16.7% in the low-dose FSE group and 34.5% in the high-dose FSE group). Immunofluorescence studies revealed that FSE-mediated restoration of E-cadherin localization counteracted AOM-induced epithelial disruptions. Conclusions: FSE exhibits potent chemopreventive potential against CRC by modulating oxidative stress, regulating key biomarkers, inducing apoptosis, and restoring epithelial integrity. These findings support further investigations into its clinical relevance for CRC prevention. Full article

Due to moisture migration effects, thermal and moisture bridges tend to form at building joints, thereby increasing the thermal conductivity coefficient of construction materials. To examine the influence of moisture transfer on the thermal performance of ‘one-line’ vertical joint walls, this study establishes a thermal–humidity coupling numerical model at the vertical joint of sandwich insulation composite walls. This model is employed to analyze the effects of various joint filling materials (aerated blocks, glass wool, concrete), insulation layer thicknesses, and environmental conditions on the thermal transfer properties of the wall joint. The results indicate that when filled with aerated blocks, the joint is most significantly affected by moisture transfer, exhibiting a heat flow loss rate of 8.08%. In high-temperature environments, the thermal transfer performance at the connection of the composite wall is particularly susceptible to humidity, with heat flow loss rates ranging from 6.17% to 8.74%. Furthermore, an increase in the thickness of the insulation layer leads to a reduction in the “heterogeneity” of the sandwich insulation wall, which reduces the wall’s effects to moisture transfer; however, this is accompanied by a rise in the heat loss rate at the connection. After accounting for the effects of hygrothermal bridging, the mean heat transfer corrected coefficient of the wall in areas with hot summers and cold winters ranges from 1.10 to 1.18 during the summer and from 1.12 to 1.16 during the winter. This finding holds significant relevance for aiding researchers in predicting thermal transfer analysis in scenarios involving wall moisture transfer. Full article

This study presents an integrated strategy to optimize biofuel production from Chlorella sorokiniana (CSO) and Chlorella vulgaris (CVU) by combining salt-induced stress and thermal pretreatment. The microalgae were cultivated in anaerobic digestate effluent (ADE) under stress and non-stress conditions to evaluate nutrient availability’s impact on biomass composition. Salt stress significantly enhanced lipid accumulation, with CVU exhibiting a 51.6% increase. Thermal pretreatment of biomass at 90 °C for 10 h achieved the highest methane yield (481 mL CH₄/g VS), with CVU outperforming CSO. Milder pretreatment conditions (40 °C for 4 h) were more energy-efficient for CSO, achieving a yield of 2.67%. Fatty acid profiles demonstrated species-specific biodiesel properties, with CSO rich in oleic acid (33.47%) offering enhanced oxidative stability and cold flow performance, while CVU showed a higher polyunsaturated fatty acid content. This research highlights the economic viability of using ADE as a low-cost cultivation medium and the potential for scalable thermal pretreatments. Future research should focus on reducing energy demands of pretreatment processes and exploring alternative stress induction methods to further enhance biofuel yields. These findings offer valuable insights for tailoring cultivation and processing strategies to maximize lipid and methane production, supporting sustainable and economically viable dual biofuel production systems. Full article

To address the limitations of poly (lactic acid) (PLA), it was blended with poly (methyl methacrylate) (PMMA) as a toughening component, using MgO nanoparticles (NPs, 0.075–0.15 wt%) as a catalyst. SEM pictures confirmed the good miscibility of the blends. Mechanical tests showed a slight decrease in elastic modulus and tensile strength for the PLA/PMMA125 sample containing 0.125% MgO. Yet, elongation at break rose by over 60% and impact strength increased by over 400% compared to pure PLA. Also, MgO facilitated the shifting of the glass transition temperature (T_g) of both polymers in DSC curves. Additionally, the absence of cold crystallization in PLA, coupled with reductions in its melting temperature (T_m) and crystallinity, were identified as critical factors contributing to improved miscibility within the reactive blend. Melt flow index (MFI) evaluation indicated a decrease in viscosity, while water contact angle measurements revealed an increase in polar groups on the surfaces of the MgO-containing samples. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses confirmed the effective distribution and dispersion of NPs throughout the blend, along with a significant decrease in crystallinity. Moreover, DFT calculations were performed to better understand the role of MgO in the reaction. The findings offered key insights into the reaction mechanism, confirming that MgO plays a crucial role in facilitating the transesterification between PLA and PMMA. These findings underscore the enhanced performance of exchange reactions between the active groups of both polymers in the presence of MgO, leading to the formation of PLA-PMMA copolymers with superior miscibility and mechanical properties. Finally, a cell culture assay confirmed the blend’s non-toxicity, showing its versatile potential. Full article

Geothermal energy is typically produced from underground reservoirs using water as the working fluid to transfer heat energy to surface and eventually to the delivery point. CO₂ has been proposed as an alternative working fluid due to its improved mobility, density and its supercritical phase state, leading thus to so-called CPG (CO₂ Plume Geothermal) systems. As a positive side effect, the injected CO₂ mass circulation in the reservoir can be considered a CO₂ storage mechanism, which, depending on the size of the porous medium, may account for few millions of CO₂ tons. Moreover, the thermosiphon effect, owned to the significant change of fluid density between the injection (cold) and the production wells (hot) as well as to its change along the wells, significantly reduces the need for pumping, hence the operating costs. In this work, we setup a mathematical model that fully describes flow in the production/injection wells doublet as well as in the geothermal reservoir. Subsequently, the model is used to evaluate the sensitivity of the beneficial effects of circulating CO₂ rather than water. Parameters such as reservoir properties, injection temperature and thermal effects, are tweaked to demonstrate the sensitivity of each one to the system performance. The results can be utilized as a guideline to the design of such systems and to the emphasis needed to be paid by the engineers. Full article

Microchannel liquid-cooled plates are widely used in high-performance electronic devices, but their heat transfer performance and pressure drop characteristics face complex challenges in the design process. In this paper, a counter-flow rectangular microchannel liquid-cooled plate is designed, and the effects of velocity, aspect ratio, and inlet/outlet forms on its heat transfer and pressure drop performance are investigated through orthogonal tests and numerical simulations. The results indicate that the velocity plays a crucial role in determining the plate’s performance. While increasing the velocity substantially enhances heat transfer efficiency, it also causes a steep rise in pressure drop. The aspect ratio has a lesser effect on the performance than the velocity, and smaller aspect ratios help to achieve a balance between thermal and flow properties. The comprehensive optimization of the inlet and outlet forms and velocity has a significant effect on the temperature uniformity and pressure drop, and the design of the cooling fluid inlet and outlet form of CM (side inlet and middle outlet) can effectively improve the temperature distribution and reduce the pressure drop at high velocity. The design parameters with the best overall performance are the aspect ratio of 2, the velocity of 0.5 m/s, and the CM inlet/outlet form (K2V0.5CM). Comparison with other design parameter sets verified that this parameter set showed significant advantages in cooling effect, temperature uniformity, flow and heat transfer performance. Finally, the correlation equation on Nu is established, and the simulated Nu as well as the calculated Nu are compared. In this thesis, a counter-flow rectangular microchannel cold plate is designed to optimize the flow rate, channel structure and other parameters through orthogonal tests to reduce the temperature gradient and balance the heat transfer and flow resistance to meet the demand for efficient heat dissipation of 350 W CPU. This study provides an important reference for the structural optimization of microchannel liquid-cooled panels and the engineering application of high-efficiency heat dissipation systems. Full article

The rising demand for edible oils underscores the potential of non-edible oils for biodiesel production. However, biodiesel’s low oxidative stability (OS) and poor cold flow properties due to high unsaturation levels limit its use. This study aims to improve OS through the partial hydrogenation of polyunsaturated FAMEs using a Ru-TPPTS biphasic catalytic system. GC-MS analysis showed that the pre-hydrogenated biodiesel contained over 85% of unsaturated FAMEs, mainly linoleic (C18:2) and oleic acid (C18:1). Hydrogenation reduced C18:2 FAME content by over 70% while increasing stearic acid level (C18:0 FAME), significantly enhancing OS by more than 135%. Further optimization is needed to meet the required quality and performance standards. Full article