Search Results (403)

AlGaN-based high-electron-mobility transistors are critical for next-generation power electronics and radio-frequency applications, yet achieving stable enhancement-mode operation with a high threshold voltage remains a key challenge. In this work, we designed p-AlGaN superlattices with different structures and performed energy band structure simulations using the device simulation software Silvaco. The results demonstrate that thin barrier structures lead to reduced acceptor incorporation, thereby decreasing the number of ionized acceptors, while facilitating vertical hole transport. Superlattice samples with varying periodic thicknesses were grown via metal-organic chemical vapor deposition, and their crystalline quality and electrical properties were characterized. The findings reveal that although gradient-thickness barriers contribute to enhancing hole concentration, the presence of thick barrier layers restricts hole tunneling and induces stronger scattering, ultimately increasing resistivity. In addition, we simulated the structure of the enhancement-mode HEMT with p-AlGaN as the under-gate material. Analysis of its energy band structure and channel carrier concentration indicates that adopting p-AlGaN superlattices as the under-gate material facilitates achieving a higher threshold voltage in enhancement-mode HEMT devices, which is crucial for improving device reliability and reducing power loss in practical applications such as electric vehicles. Full article

Flexible perovskite solar cells (FPSCs) hold great promise for lightweight and wearable photovoltaics, but improving their efficiency and durability under mechanical stress remains a key challenge. In this work, we fabricate and characterize flexible planar FPSCs on a polyethylene terephthalate (PET). A phenethylammonium iodide (PEAI) surface passivation layer is introduced on the perovskite to form a two-dimensional capping layer, and its impact on device performance and stability is systematically studied. The champion PEAI-passivated flexible device achieves a power conversion efficiency (PCE) of ~16–17%, compared to ~14% for the control device without PEAI. The improvement is primarily due to an increased open-circuit voltage and fill factor, reflecting effective surface defect passivation and improved charge carrier dynamics. Importantly, mechanical bending tests demonstrate robust flexibility: the PEAI-passivated cells retain ~85–90% of their initial efficiency after 700 bending cycles (radius ~5 mm), significantly higher than the ~70% retention of unpassivated cells. This work showcases that integrating a PEAI surface treatment with optimized electron (SnO₂) and hole (spiro-OMeTAD) transport layers (ETL and HTL) can simultaneously enhance the efficiency and mechanical durability of FPSCs. These findings pave the way for more reliable and high-performance flexible solar cells for wearable and portable energy applications. Full article

This work explored an electrochemical approach for synthesizing lanthanum-modified nickel oxide (NiO_x:La) as a hole transport layer (HTL) in inverted perovskite solar cells (IPSCs). By varying the La³⁺ concentration, the chemical, charge transport, structural, and morphological properties of the NiO_x:La film and the HTL/PVK interface were evaluated to enhance photovoltaic performance. X-ray photoelectron spectroscopy (XPS) confirmed La³⁺ incorporation, a higher Ni³⁺/Ni³⁺ ratio, and a valence band shift, improving p-type conductivity. Electrochemical impedance spectroscopy and Mott–Schottky analyses indicated that NiO_x:La 0.5% exhibited the lowest resistance and the highest carrier density, correlating with higher recombination resistance. The NiO_x:La 0.5% based cell achieved a PCE of 20.08%. XRD and SEM confirmed no significant changes in PVK structure, while photoluminescence extinction demonstrated improved charge extraction. After 50 days, this cell retained 80% of its initial PCE, whereas a pristine NiO_x device retained 75%. Hyperspectral imaging revealed lower optical absorption loss and better homogeneity. These results highlight NiO_x:La as a promising HTL for efficient and stable IPSCs. Full article

Developing high-performance photocatalysts for solar hydrogen production requires the synergistic modulation of chemical composition, nanostructure, and charge carrier transport pathways. Herein, we report a Cs and P co-doped tubular graphitic carbon nitride (Cs/PTCN-x) photocatalyst synthesized via a strategy that integrates elemental doping with morphological engineering. Structural characterizations reveal that phosphorus atoms substitute lattice carbon to form P-N bonds, while Cs⁺ ions intercalate between g-C₃N₄ layers, collectively modulating surface electronic states and enhancing charge transport. Under visible-light irradiation (λ ≥ 400 nm), the optimized Cs/PTCN-3 catalyst achieves an impressive hydrogen evolution rate of 8.085 mmol·g⁻¹·h⁻¹—over 33 times higher than that of pristine g-C₃N₄. This remarkable performance is attributed to the multidimensional synergy between band structure tailoring and hierarchical porous tubular architecture, which together enhance light absorption, charge separation, and surface reaction kinetics. This work offers a versatile approach for the rational design of g-C₃N₄-based photocatalysts toward efficient solar-to-hydrogen energy conversion. Full article

In the field of intelligent decision-making, time-series data collected by sensors serves as the core carrier for interaction between the physical and digital worlds. Accurate analysis is the cornerstone of decision-making in critical scenarios, such as industrial monitoring and intelligent transportation. However, the inherent spatio-temporal coupling characteristics and cross-period long-range dependency of sensor data cause traditional time-series prediction methods to face performance bottlenecks in feature decoupling and multi-scale modeling. This study innovatively proposes a Spatio-Temporal Attention-Enhanced Network (TSEBG). Breaking through traditional structural designs, the model employs a Squeeze-and-Excitation Network (SENet) to reconstruct the convolutional layers of the Temporal Convolutional Network (TCN), strengthening the feature expression of key time steps through dynamic channel weight allocation to address the redundancy issue of traditional causal convolutions in local pattern capture. A Bidirectional Gated Recurrent Unit (BiGRU) variant based on a global attention mechanism is designed, leveraging the collaboration between gating units and attention weights to mine cross-period long-distance dependencies and effectively alleviate the gradient disappearance problem of Recurrent Neural Network (RNN-like) models in multi-scale time-series analysis. A hierarchical feature fusion architecture is constructed to achieve multi-dimensional alignment of local spatial and global temporal features. Through residual connections and the dynamic adjustment of attention weights, hierarchical semantic representations are output. Experiments show that TSEBG outperforms current dominant models in time-series single-step prediction tasks in terms of accuracy and performance, with a cross-dataset R² standard deviation of only 3.7%, demonstrating excellent generalization stability. It provides a novel theoretical framework for feature decoupling and multi-scale modeling of complex time-series data. Full article

The tin dioxide (SnO₂) thin films in this work were prepared by using plasma-enhanced atomic layer deposition (PEALD), and a systematic analysis was conducted to evaluate the influence of post-deposition annealing at various temperatures in a nitrogen–hydrogen mixed atmosphere on their surface morphology, optical behavior, and electrical performance. The SnO₂ films were characterized by using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Hall effect measurements. With increasing annealing temperatures, the SnO₂ films exhibited enhanced crystallinity, a higher oxygen vacancy (O_V) peak area ratio, and improved mobility and carrier concentration. These enhancements make the annealed SnO₂ films highly suitable as electron transport layers (ETLs) in perovskite solar cells (PSCs), providing practical guidance for the design of high-performance PSCs. Full article

This study presents the first comprehensive theoretical investigation utilizing SCAPS-1D simulation to systematically evaluate eight hole transport materials for CsPbI₂Br perovskite solar cells under authentic indoor LED conditions (560 lux, 5700 K color temperature). Unlike previous studies employing simplified illumination assumptions, our work establishes fundamental design principles for indoor photovoltaics through rigorous material property correlations. The investigation explores the influence of layer thickness and defect concentration on performance to identify optimal parameters. Through detailed energy band alignment analysis, we demonstrate that CuI achieves superior performance (PCE: 23.66%) over materials with significantly higher mobility, revealing that optimal band alignment supersedes carrier mobility under low-light conditions. Analysis of HTL and absorber layer thickness, bulk defect concentration, interface defect density, and an HTL-free scenario showed that interface defect concentration and absorber layer parameters have greater influence than HTL thickness. Remarkably, ultra-thin HTL layers (0.04 μm) maintain >99% efficiency, offering substantial cost reduction potential for large-scale manufacturing. Under optimized conditions of a 0.87 μm absorber layer thickness, defect concentration of 10¹⁵ cm⁻³, interface defect concentration of 10⁹ cm⁻³, and CuI doping concentration of 10¹⁷ cm⁻³, PCE reached 28.57%, while the HTL-free structure achieved 17.6%. This study establishes new theoretical foundations for indoor photovoltaics, demonstrating that material selection criteria differ fundamentally from outdoor applications. Full article

Tin(II) sulfide(SnS)/titanium(IV) oxide (TiO₂) heterostructure thin films were prepared by radio-frequency magnetron sputtering to investigate the enhancement effect of the formed heterojunction on the photocatalytic performance. By adjusting the sputtering time to vary the thickness of the SnS layer, the crystallinity and light-absorption properties of the light-absorbing layer and the quality of the heterojunction interface were effectively controlled, thereby optimizing the fabrication process of the heterojunction. It was found that when the SnS layer thickness was 244 nm and the TiO₂ layer thickness was 225 nm, the heterostructure film exhibited optimal photoelectrochemical performance, generating the highest photocurrent of 3.03 µA/cm² under visible light, which was 13.8 times that of a pure TiO₂ film and 2.4 times that of a pure SnS film of the same thickness. Additionally, it demonstrated the highest degradation efficiency for methylene blue dye. The improved photoelectrochemical performance of the SnS/TiO₂ heterostructure film can be primarily attributed to the following: (1) the incorporation of narrow-bandgap SnS effectively broadens the light-absorption range, improving visible-light harvesting; (2) the staggered band alignment between SnS and TiO₂ forms a type-II heterojunction, significantly enhancing the charge carrier separation and transport efficiency. The present work demonstrated the feasibility of magnetron sputtering for constructing high-quality SnS/TiO₂ heterostructures, providing insights into the design and fabrication of photocatalytic heterojunctions. Full article

One-dimensional (1D) nanomaterials have attracted considerable attention in the fabrication of nano-scale optoelectronic devices owing to their large specific surface areas, high surface-to-volume ratios, and directional electron transport channels. Compared to 1D metal oxide nanostructures, 1D metal sulfides have emerged as promising candidates for high-efficiency photodetectors due to their abundant surface vacancies and trap states, which facilitate oxygen adsorption and dissociation on their surfaces, thereby suppressing intrinsic carrier recombination while achieving enhanced optoelectronic performance. This review focuses on recent advancements in the performance of photodetectors fabricated using 1D binary metal sulfides as primary photosensitive layers, including nanowires, nanorods, nanotubes, and their heterostructures. Initially, the working principles of photodetectors are outlined, along with the key parameters and device types that influence their performance. Subsequently, the synthesis methods, device fabrication, and photoelectric properties of several extensively studied 1D metal sulfides and their composites, such as ZnS, CdS, SnS, Bi₂S₃, Sb₂S₃, WS₂, and SnS₂, are examined. Additionally, the current research status of 1D nanostructures of MoS₂, TiS₃, ReS₂, and In₂S₃, which are predominantly utilized as 2D materials, is explored and summarized. For systematic performance evaluation, standardized metrics encompassing responsivity, detectivity, external quantum efficiency, and response speed are comprehensively tabulated in dedicated sub-sections. The review culminates in proposing targeted research trajectories for advancing photodetection systems employing 1D binary metal sulfides. Full article

Hematite (Fe₂O₃) has been accepted as a promising and potential photo(electro)catalyst. However, its poor carrier separation and transfer efficiency has limited its application for photoelectrocatalytic (PEC) water oxidation. Herein, a S-doped FeOOH (S:FeOOH) layer was rationally designed and grown on Fe₂O₃ to construct a S:FeOOH/Fe₂O₃ composite photoanode. The obtained S:FeOOH/Fe₂O₃ photoanodes were fully characterized. The surface injection efficiency for Fe₂O₃ was then significantly increased with a high η_surface value of 92.8%, which increases to 2.98 times for Fe₂O₃ and 2.16 times for FeOOH/Fe₂O₃, respectively. With 2.43 mA cm^‒2 at 1.23 V, the optimized S:FeOOH/Fe₂O₃ photoanode was entrusted with a higher photocurrent density. The onset potential for S:FeOOH/Fe₂O₃ cathodically shifts 70 mV over Fe₂O₃. The improved PEC performance suggests that the S:FeOOH layer acts as ultrafast transport channels for holes at the photoanode/electrolyte interface, suppressing surface charge recombination. A Z-scheme band alignment between Fe₂O₃ and S:FeOOH was deduced from the UV–Vis and UPS spectra to promote charge transfer. This method provides an alternative for the construction of photoanodes with enhanced PEC water splitting performance. Full article

The low-symmetry Weyl semimetallic Td-phase WTe₂ exhibits both a distinct out-of-plane damping torque (${\tau }_{\mathrm{DL}}$) and exceptional charge–spin interconversion efficiency enabled by strong spin-orbit coupling, positioning it as a prime candidate for spin–orbit torque (SOT) applications in two-dimensional transition metal dichalcogenides. Herein, we report on thickness-dependent unconventional out-of-plane ${\tau }_{\mathrm{DL}}$ in chemically vapor-deposited (CVD) polycrystalline Td-WTe₂ (t)/Ni₈₀Fe₂₀/MgO/Ti (Td-WTN-t) heterostructures. Angle-resolved spin-torque ferromagnetic resonance measurements on the Td-WTN-12 structure showed significant spin Hall conductivities of σ_SH,y = 4.93 × 10³ (ℏ/2e) Ω⁻¹m⁻¹ and σ_SH,z = 0.81 × 10³ (ℏ/2e) Ω⁻¹m⁻¹, highlighting its potential for wafer-scale spin–orbit torque device applications. Additionally, a detailed examination of magnetotransport properties in polycrystalline few-layer Td-WTe₂ films as a function of thickness revealed a marked amplification of the out-of-plane magnetoresistance, which can be ascribed to the anisotropic nature of charge carrier scattering mechanisms within the material. Spin pumping measurements in Td-WTN-t heterostructures further revealed thickness-dependent spin transport properties of Td-WTe₂, with damping analysis yielding an out-of-plane spin diffusion length of λ_SD ≈ 14 nm. Full article

The hole-transport layer (HTL) plays a pivotal role in engineering high-performance inverted perovskite solar cells (PSCs), as it governs both hole extraction/transport dynamics and critically impacts the crystallization quality of the perovskite absorber layer in device architectures. Recent advancements have highlighted self-assembled monolayers (SAMs) as promising candidates for next-generation HTL materials in inverted PSCs due to their intrinsic advantages over conventional counterparts. These molecularly engineered interfaces demonstrate superior characteristics including simplified purification processes, tunable molecular structures, and enhanced interfacial compatibility with device substrates. This review systematically examines the progress, existing challenges, and future prospects of SAM-based HTLs in inverted photovoltaic systems, aiming to establish a systematic framework for understanding their structure–property relationships. The review is organized into three sections: (1) fundamental architecture of inverted PSCs, (2) molecular design principles of SAMs with emphasis on head-group functionality, and (3) recent breakthroughs in SAM-engineered HTLs and their modification strategies for HTL optimization. Through critical analysis of performance benchmarks and interfacial engineering approaches, we elucidate both the technological merits and inherent limitations of SAM implementation in photovoltaic devices. Furthermore, we propose strategic directions for advancing SAM-based HTL development, focusing on molecular customization and interfacial engineering to achieve device efficiency and stability targets. This comprehensive work aims to establish a knowledge platform for accelerating the rational design of SAM-modified interfaces in next-generation optoelectronic devices. Full article

Perovskite/organic tandem solar cells, as a next-generation high-efficiency photovoltaic technology, integrate the tunable bandgap characteristics of perovskite materials with the broad spectral absorption advantages of organic semiconductors, demonstrating remarkable potential to surpass the theoretical efficiency limits of single-junction cells, enhance device stability, and expand application scenarios. This architecture supports low-temperature solution processing and offers tunable bandgaps, lightweight flexibility, and ecofriendly advantages. This review systematically summarizes research progress in this field, with a primary focus on analyzing the working principles, performance optimization strategies, and key challenges of the technology. Firstly, the article discusses strategies such as defect passivation, crystallization control, and suppression of phase separation in wide-bandgap perovskite sub-cells, offering insights into mitigating open-circuit voltage losses. Secondly, for the narrow-bandgap organic sub-cells, this paper highlights the optimization strategies for both the active layer and interfacial layers, aiming to improve spectral utilization and enhance power conversion efficiency. Additionally, this paper emphasizes the optimization of optical transparency, electrical conductivity, and energy level alignment in the recombination layer, providing theoretical guidance for efficient current matching and carrier transport. Full article

This study presents an effective strategy to enhance the efficiency and stability of perovskite solar cells (PSCs) by integrating neodymium-doped upconversion nanoparticles (UCNPs) coated with a TiO₂ shell into the mesoporous electron transport layer. The incorporation of neodymium (Nd³⁺) as a novel sensitizer shifts the near-infrared (NIR) absorption band away from the water vapor absorption region in the solar spectrum. This modification enables UCNPs to efficiently convert NIR light into ultraviolet (UV) and blue wavelengths, which are readily absorbed by TiO₂, generating additional charge carriers and improving photovoltaic performance. The optimized PSCs, fabricated by blending 30% UCNPs@TiO₂ with commercial TiO₂ paste, achieved a peak power conversion efficiency (PCE) of 21.71%, representing a 20.4% improvement over the control (18.04%). This enhancement included a 0.9% increase in the open-circuit voltage (V_oc), a 6.6% rise in the short-circuit current density (J_sc), and an 11.9% boost in the fill factor (FF). Additionally, the optimized PSCs exhibited remarkable stability, retaining over 90% of their initial PCE after 900 h in humid conditions, compared to only 70% for the control. These improvements result from enhanced light absorption, reduced moisture infiltration, and lower defect-related recombination. This approach provides a promising pathway for developing highly efficient and durable PSCs. Full article

Organic semiconductors have garnered significant interest owing to their low cost, flexibility, and suitability for large-area electronics, making them vital for burgeoning fields such as flexible electronics, wearable devices, and green energy technologies. The performance of organic electronic devices is crucially determined by their interfacial electronic structure. Specifically, interfacial phenomena such as band bending significantly influence carrier injection, transport, and recombination, making their control paramount for enhancing device performance. This review investigates the interplay among molecular orientation, interfacial charge transfer, and interfacial chemical reactions as the primary drivers of interface band bending. Furthermore, it critically examines effective strategies for optimizing interfacial properties via interface engineering, focusing on interlayer insertion and template layer methods. The review concludes with a summary and outlook, emphasizing the integration of interface design with material development and device architecture to realize next-generation, high-performance organic electronic devices exhibiting improved efficiency and stability. Full article