Search Results (2,349)

Aiming to address the problems of the violent fluctuation of winch traction rope and tire forces and the high safety risk caused by coupling ship motions (rolling, pitching, and heaving), wind loads, and deck space limitations in carrier-based aircraft, this paper focuses on a multi-winch traction system on a small deck. A fully coupled dynamic model of an aircraft landing gear–tire–rope–winch system is constructed, ADAMS2020 and MATLAB/Simulink (MATLAB R2021b) co-simulations are used to develop the three-winch and five-winch traction system models, and a Fiala tire model and a telescopic landing gear model are adopted to build a precise mechanical model of the aircraft. The PID control strategy is proposed, based on the Bessel curve, to control the driving trajectory of the aircraft, and the quantitative influence of ship motion, winch number, and preset trajectory on traction dynamic characteristics is systematically studied. Compared to without trajectory control, the peak force of the winch rope before the start-up phase of the three-winch system is reduced by 54.9%, and the five-winch system is reduced by 57.6%. The fluctuation amplitude of the lateral force of the rear wheel is greater than that of the front wheel, up to a maximum of 215% of the front wheel. The correlation coefficient between the theoretical model and the simulation results is 0.91~0.97, and the error is less than 12%. The PID control strategy based on the Bessel trajectory can significantly improve the steadiness and security of the carrier-based aircraft winch traction system on a small deck. The study delivers the requisite theory and engineering means for the optimized design of carrier-based aircraft traction systems. Full article

Most nanoparticles and microparticles used as carriers of bioactive compounds are spherical in shape. Such particles are the easiest to obtain, as many processes spontaneously minimize the surface energy of the objects produced. However, in recent years, scientists have turned their attention to non-spherical particles in the hope of obtaining particles that interact with their environment in a tailored manner. The production of such particles should be easy and reproducible. The best candidates are spheroids produced by various methods. The most often used is the linear transformation of spheres during processes that preserve constant particle volume. The typical process consists of stretching a polymer matrix filled with spherical particles. The article delivers a critical overview of methods, discussing their advantages and disadvantages. A list of presented methods also includes the preparation of spheroids by polymer solution emulsification-solvent evaporation, controlled dispersion polymerization, electrohydrodynamic jetting, adsorption of amphiphilic copolymers on solid particles, and copolymer self-organization processes, as well as microfluidic methods, deformation of spherical particles into spheroids by irradiation, and phase microseparation. A special section is devoted to the self-organization of the particles at the phase boundaries. Eventually, the preparation and selected properties of two-dimensional and three-dimensional assemblies of spheroidal particles, particularly the preparation of a quasi-nematic colloidal crystal, are discussed. Full article

Iron powder represents a promising carbon-free, sustainable fuel, yet its practical utilisation in combustion has not yet been realised. Achieving stable, efficient iron-only flames is challenging, and the environmental impact of hybrid iron-hydrocarbon combustion, including particle emissions, is not fully understood. This study investigates hybrid methane–iron powder flames to assess iron’s role in modifying gas and particle phase emissions and its potential as a sustainable energy carrier. The combustion of iron was investigated at both the single particle and powder flow scales. Experimental diagnostics combined high-speed and microscopic imaging, ex situ particle sizing, in situ gas analysis, and aerosol measurements using an Aerodynamic Particle Sizer (APS™) and a Scanning Mobility Particle Sizer (SMPS™). For single particle combustion, high-speed imaging revealed rapid particle heating, oxide shell growth, cavity formation, micro-explosions, and nanoparticle release. For powder combustion, at 0.5 g/min and 1.26 g/min, the experiment yielded oxidation fractions of 15.15% and 23.43%, respectively, and increased CO₂ emissions by 0.22–0.35 vol% relative to methane–air flames, while NOx changes were negligible. Aerosol analysis showed a supermicron mode at ~2 µm and submicron ultrafine particles of 89% <100 nm with a modal diameter of ~56 nm. The observed ultrafine particle emissions highlight the need to evaluate health, material-loss, and fuel-recycling implications. Burner optimisation or premixed strategies could reduce CO₂ emissions while enhancing iron oxidation efficiency. Full article

Solid–liquid stirred tanks are widely used in multiphase processes, including bioreactors for mesenchymal stem cell (MSC) culture, yet simultaneous experimental data for both dispersed and carrier phases remain limited. Here, a refractive index-matched (RIM) suspension of PMMA microparticles ($d_p=168\mathrm{\mu m}$, ${\rho }_p/{\rho }_l\approx 0.96$) in an NH₄SCN solution is studied at an intermediate Reynolds number ($Re\approx 5000$), low Stokes number ($St=0.078$), and particle volume fractions $0.1\le {\alpha }_p\le 0.5$ v%. This system was previously established and studied for the effect of addition of particles on the carrier phase. In this work, a dual-camera PIV set-up provides simultaneous velocity fields of the liquid and particle phases in a stirred tank equipped with a three-blade down-pumping HTPGD impeller. The liquid mean flow and circulation loop remained essentially unchanged with particle loading, whereas particle mean velocities were lower than single-phase and liquid-phase values in the impeller discharge. Turbulence levels diverged between phases: liquid-phase turbulent kinetic energy (TKE) in the impeller region increased modestly with ${\alpha }_p$, while solid-phase TKE was attenuated. Slip velocity maps showed that particles lagged the fluid in the impeller jet and deviated faster from the wall in the upward flow, with slip magnitudes increasing with ${\alpha }_p$. An approximate axial force balance indicated that drag dominates over lift in the impeller and wall regions, while the balance is approximately satisfied in the tank bulk, providing an experimental benchmark for refining drag and lift models in this class of stirred tanks. Full article

In the last few years, Thin Film Transistors (TFTs) based on materials such as amorphous Indium–Gallium–Zinc Oxide (a-IGZO) have gained interest in large-area and low-cost electronics due to their high carrier mobility, high on/off current ratio, low off-state current, and steep subthreshold slope. These characteristics make IGZO TFTs suitable for radio-frequency identification (RFID) tags, analog-to-digital converters (ADCs), logic circuits, sensors, and analog components, including operational amplifiers (OPAMPs). This work presents the implementation and characterization of an OPAMP based on n-type a-IGZO TFTs fabricated on glass substrate. Two previously reported design strategies were integrated: a positive feedback network to increase the output impedance and a topology to enhance the transconductance of the driver transistors, both in the differential input stage. A gain of 26 dB, a bandwidth of 2.4 kHz, a gain–bandwidth product (GBWP) of 48 kHz, and a phase margin of 64° were obtained, which confirms the reliability of the design and the fabrication process. Full article

In recent years, biomass utilization has attracted extensive attention. Herein, hexagonal/cubic ZnIn₂S₄ (ZIS) heterojunction catalysts were synthesized via a solvothermal method for the selective oxidation of 5-hydroxymethylfurfural (HMF) to 2,5-diformylfuran (DFF). The results demonstrated that the constructed heterojunctions effectively promoted carrier separation. The optimal catalyst achieved an HMF conversion rate of 88.8% and a DFF yield of 86.6% within 1 h in the open air. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) characterizations confirmed the successful fabrication of the composite phase structure and revealed a porous spherical morphology. Equivalent circuit fitting of electrochemical impedance spectroscopy (EIS) data indicated that the hexagonal/cubic heterojunctions possessed the lowest charge transfer resistance (Rct = 5825 Ω), which effectively reduced interfacial charge transfer resistance and accelerated the transport of photoinduced carriers. Radical quenching experiments and electron paramagnetic resonance (EPR) spectroscopy identified superoxide radicals (·O₂⁻) as the primary reactive species. Meanwhile, density functional theory (DFT) calculations elucidated the formation of the built-in electric field and the charge transfer mechanism. This work’s construction of Type-II ZIS heterojunctions effectively addressed the issue of rapid carrier recombination in pristine ZIS materials, providing a feasible strategy for biomass valorization. Full article

This study utilized a dynamic cross-linking algorithm to formulate a chemical cross-linked hydrogel model of poly(N-isopropylacrylamide) (PNIPAM) with N, N’-methylenebisacrylamide (BIS). Molecular dynamics (MD) simulations were conducted to investigate the temperature sensitivity and ibuprofen release mechanism of this hydrogel under varying cross-linking degrees and water contents. The low critical solution temperature (LCST) of the hydrogel was determined based on changes in solvent-accessible surface area (SASA) and hydrogen bond count. The LCST was found to be between 300 and 310 K. As the temperature increased, both SASA and hydrogen bond counts generally exhibited a gradual decrease. However, near the LCST, polymer chain collapse temporarily exposed the hydrophilic groups of the PNIPAM, forming hydrophilic regions that increased the contact area with water. This led to a transient increase in SASA (8% higher than that before 300 K) and hydrogen bond counts (6.25% higher than that at 290 K). Concurrently, Young’s modulus of the PNIPAM hydrogel was found to decrease with increasing water content (from 3.11 GPa to 2.59 GPa, representing a 16.7% decrease when water content increased from 0% to 50% for 80% cross-linking degree) and increase with rising cross-linking density (from 2.02 GPa to 2.94 GPa, representing a 45.5% increase when the cross-linking degree increased from 0% to 80% for 20% water content). These findings indicate that enhancing cross-linking density is an effective strategy for improving the hydrogel’s mechanical properties. A PNIPAM–ibuprofen delivery model was constructed and molecular dynamics (MD) simulations were conducted, revealing temperature dependence release behavior. Below the LCST, the PNIPAM hydrogel remains in a highly swollen state (PNIPAM single-chain radius of gyration, Rg = 0.64 nm at 290 K), with ibuprofen molecules adsorbed within the PNIPAM polymer chain network. Conversely, above the LCST, PNIPAM undergoes phase separation (Rg decreases to 0.56 nm at 320 K, representing a 12.5% decrease), resulting in volume contraction (cavity volume reduced by 35%) and disruption of the hydrogen bond network. This process results in the release of ibuprofen molecules, accompanied by an increase in their diffusion coefficient from 1.3817 × 10⁻⁹ (280 K) to 4.2847 × 10⁻⁹ m²/s (320 K). Concurrently, the interaction energy with PNIPAM experiences a decline, from −126.72 kcal/mol to −108.69 kcal/mol. The findings of this study provide insights into the optimization of the structural stability of ibuprofen delivery carriers. Full article

Tin selenide (SnSe) is a sustainable, lead-free IV–VI semiconductor whose layered orthorhombic crystal structure induces pronounced electronic and phononic anisotropy, enabling diverse energy-related functionalities. This review systematically summarizes recent progress in understanding the structure–property–processing relationships that govern SnSe performance in thermoelectric and optoelectronic applications. Key crystallographic characteristics are first discussed, including the temperature-driven Pnma–Cmcm phase transition, anisotropic band and valley structures, and phonon transport mechanisms that lead to intrinsically low lattice thermal conductivity below 0.5 W m⁻¹ K⁻¹ and tunable carrier transport. Subsequently, major synthesis strategies are critically compared, spanning Bridgman and vertical-gradient single-crystal growth, spark plasma sintering and hot pressing of polycrystals, as well as vapor- and solution-based thin-film fabrication, with emphasis on process windows, stoichiometry control, defect chemistry, and microstructure engineering. For thermoelectric applications, directional and temperature-dependent transport behaviors are analyzed, highlighting record thermoelectric performance in single-crystal SnSe at hi. We analyze directional and temperature-dependent transport, highlighting record thermoelectric figure of merit values exceeding 2.6 along the b-axis in single-crystal SnSe at ~900 K, as well as recent progress in polycrystalline and thin-film systems through alkali/coinage-metal doping (Ag, Na, Cu), isovalent and heterovalent substitution (Zn, S), and hierarchical microstructural design. For optoelectronic applications, optical properties, carrier dynamics, and photoresponse characteristics are summarized, underscoring high absorption coefficients exceeding 10⁴ cm⁻¹ and bandgap tunability across the visible to near-infrared range, together with interface engineering strategies for thin-film photovoltaics and broadband photodetectors. Emerging applications beyond energy conversion, including phase-change memory and electrochemical energy storage, are also reviewed. Finally, key challenges related to selenium volatility, performance reproducibility, long-term stability, and scalable manufacturing are identified. Overall, this review provides a process-oriented and application-driven framework to guide the rational design, synthesis optimization, and device integration of SnSe-based materials. Full article

Coordination polymers (CPs) are garnering attention in the field of medicine day by day. The goal is to develop a CP with biosafe and environment-friendly characteristics. Herein, we report two such novel 3D coordination polymers of zinc-inosine-5′-monophosphate (Zn-IMP) and bpe/azpy (as linkers) which were engineered as metal–organic frameworks that can be used as drug carriers for hydroxyurea (HU). We employed SCXRD, PXRD, solid-state CD, FTIR and TGA for crystal structure characterizations; the results achieved 3D coordination polymers which contain a P2₁ space group with chiral distorted tetrahedral geometry. Solution phase studies like UV–vis and CD were carried out to understand mechanistic pathways for interaction and chirality, respectively. We have also performed computational studies to evaluate the drug delivery capacity of both 3D CPs. Molecular docking and multi-pH molecular dynamics (MD) quantify that HU binds more strongly with CP−1 (ΔG =−10.87 ± 0.12) as compared to CP−2 (ΔG = −7.59 ± 0.26 kcal·mol⁻¹), at normal and basic pH. MD simulation analysis indicated that a more compact and rigid cavity is observed by CP−1 as compared to CP−2 at physiological pH. Across acidic pH, for CP−1 the ligand RMSD increases markedly and U becomes slightly less negative, which indicated partial loss of contacts, thus releasing drugs in a tumor-like environment more easily. These result showed that CP−1 offers stronger binding, higher structural stability and a more pronounced pH-responsive release profile than CP−2, making CP-1 more promising candidate for targeted HU drug delivery, while CP−2 may serve as a weaker-binding, faster-release complement. Full article

Owing to its narrow bandgap and excellent thermal stability, formamidinium–lead triiodide (FAPbI₃) is a promising perovskite for high-performance, wide-spectrum photodetectors. Here, we selected long-chain n-heptanoic acid as the passivating agent and introduced it onto the perovskite surface via post-treatment, thereby enabling the fabrication of high-quality α-FAPbI₃ perovskite films and photodetectors. It is found that the carboxylic acid group in the n-heptanoic acid molecule can effectively passivate crystal defects, greatly reduce the density of defect states in the perovskite film, and inhibit the non-radiative recombination of carriers. The α-FAPbI₃ perovskite phase was effectively stabilized. The responsivity of the photodetector optimized by n-heptanoic acid is as high as 0.47 A W⁻¹ at 740 nm. At the same time, the optimized device still maintains 95% of its initial performance after 552 h of storage in an air environment with a room temperature of 25 °C and a relative humidity of 25%. This method provides a reliable way to prepare a high-performance and stable α-FAPbI₃ photodetector. Full article

Global Navigation Satellite System (GNSS) signal acquisition in high-dynamic environments faces significant challenges due to large Doppler frequency offsets and stringent computational constraints. This paper proposes a frequency-domain compressed acquisition algorithm that reformulates the conventional two-dimensional code-phase/Doppler search as a set of independent one-dimensional sparse recovery problems. Doppler uncertainty is modeled as sparsity in a discretized frequency dictionary, and a low-coherence measurement matrix is designed offline via projected gradient descent with a two-stage annealing strategy. The resulting matrix significantly reduces maximum coherence and supports reliable sparse recovery from a small number of compressed measurements. During online operation, the receiver forms compressed observations for all code phases through efficient matrix operations and recovers sparse Doppler spectra using lightweight orthogonal matching pursuit. Simulation results show that the proposed method achieves a several-fold reduction in computational cost compared with classical parallel code-phase search while maintaining high detection probability at low carrier-to-noise density ratios and under large Doppler offsets, providing an effective solution for resource-constrained GNSS receivers in high-dynamic scenarios. Full article

In this work, we have used the bubble template solvothermal method to prepare TiO₂ Hollow Spheres (THS) for in situ growth of WS₂ on their surfaces and a three-phase TiO₂ Hollow Spheres/WS₂ (THS/WS₂) heterostructure composite. We also investigated the influence of W/Ti molar ratio on the morphology, structure, and optical properties of the delaminated THS/WS₂ composite and studied its photocatalytic activity to degrade RhB in visible light. Experiment result expresses that THS/WS₂-0.20 material shows the best photocatalytic activity, which is 3.9 times higher than that of THS alone. On this basis, the process of photogenerated charge carriers and photocatalytic charge transfer on the surface of the delaminated THS/WS₂ composite was elucidated, which provides a technical support for the fabrication and research of the mechanism of a three-dimensional TiO₂-based heterojunction photocatalyst. Full article

In this study, dextran-based hydrogels were synthesized in dimethyl sulfoxide via free-radical polymerization with three structurally different crosslinking agents: divinyl benzene (DVB), diethylene glycol diacrylate (DEGDA), and 4,4′-di(methacryloylamino)azobenzene (DMAAazoB). Their morphology, swelling ability, mechanical properties, and potential for controlled release of the model substance (uracil) were examined, with the results showing that the chemical structure and chain length of the crosslinking agents significantly influence the structural and functional properties of hydrogels. Hydrogels crosslinked with DMAAazoB showed the highest swelling ability at pH 3 and pH 6 (2552 and 1696%, respectively), associated with protonation effects and sponge-like morphology, while simultaneously showing the lowest mechanical strength (20 and 47 MPa). In vitro simulations of gastrointestinal digestion showed that uracil was not released in the gastric phase, while in the intestinal environment, the release was significant, especially in Dex-DMAAzoB hydrogels (88.52%). The absence of azoreductases in the simulated system indicates that the release of the drug in real conditions would likely be even more pronounced. The Dex-DAAazoB hydrogel exhibited a slight antibacterial effect, producing inhibition zones of 8 and 7 mm against Escherichia coli ATCC 8739 and Staphylococcus epidermidis ATCC 12228, respectively. In contrast, the remaining hydrogel formulations showed no detectable antibacterial activity toward either bacterial strain, indicating their microbiological inertness and supporting their suitability as carrier matrices for antitumor drug delivery in colorectal cancer therapy. The obtained results confirm that azo-crosslinked dextran hydrogels, with an optimized amount of crosslinking agent, are promising carriers for the targeted and controlled delivery of antitumor drugs to the colorectal region. Full article

Livestock manure is a major source of environmental pollution and greenhouse gas emissions if improperly managed. Aerobic composting represents a sustainable approach to manure recycling that can stabilize organic matter, mitigate carbon loss, and recover nutrients for agricultural use. In this study, sheep manure was mixed with sawdust to optimize the carbon-to-nitrogen (C/N) ratio and enhance aeration, and the mixture was subjected to aerobic composting with a cellulose-degrading microbial inoculant. To rigorously evaluate the biological effects, a control treated with sterilized inoculant was included to eliminate nutrient inputs from the carrier matrix. The inoculant significantly improved composting performance by extending the thermophilic phase by five days and reducing the C/N ratio to 19.8 on day 32, thereby shortening the composting cycle. Moreover, microbial inoculation enhanced nutrient retention, resulting in a 20.14% increase in total nutrient content, while the germination index (GI) reached 89.75%, indicating high compost maturity and reduced phytotoxicity. Microbial community analysis revealed that cellulose-degrading inoculants significantly altered microbial richness and diversity and accelerated community succession. Redundancy analysis (RDA) and hierarchical partitioning analysis showed that total organic carbon (TOC) and GI were the main environmental drivers of bacterial community dynamics, whereas pH and GI primarily regulated fungal community succession. These findings suggest a strong link between compost maturity and microbial community restructuring. This study demonstrates that cellulose-degrading microbial inoculation accelerates the composting of sheep manure, enhances organic matter degradation, and improves fertilizer efficiency while reducing the phytotoxicity of the final product. Full article

High-speed silicon (Si) photonic transmitters operating in the O-band require higher on-chip optical power to support advanced modulation formats and ever-increasing line rates. A straightforward approach is to operate laser diodes at higher output power or employ more specialized sources, but this raises cost and exacerbates nonlinear effects such as self-phase modulation, two-photon absorption, and free-carrier generation in high-index-contrast Si waveguides. This paper proposes a low-cost 4 × 1 tree-cascade multimode interference (MMI) power combiner on a Si-on-insulator platform at 1310 nm wavelength that enables coherent power scaling while remaining fully compatible with standard commercial O-band lasers. The device employs adiabatic tapers and low-loss S-bends to ensure uniform field evolution, suppress local field enhancement, and mitigate nonlinear phase accumulation. The optimized layout occupies a compact footprint of 12 µm × 772 µm and achieves a simulated normalized power transmission of 0.975 with an insertion loss of 0.1 dB. Spectral analysis shows a 3 dB bandwidth of 15.8 nm around 1310 nm, across the O-band operating window. Thermal analysis shows that wavelength drift associated with ±50 °C temperature variation remains within the device bandwidth, ensuring stable operation under realistic laser self-heating and environmental changes. Owing to its broadband response, fabrication tolerance, and compatibility with off-the-shelf laser diodes, the proposed combiner is a promising building block for O-band transmitters and photonic neural-network architectures based on cascaded splitter and combiner meshes, while preserving linear transmission and enabling dense, large-scale photonic integration. Full article