Search Results (186)

A novel reflective metasurface (RMS) is proposed in this paper. The MS measures 128 × 128 × 2.794 mm³ and consists of a six-layer vertically stacked structure, with a liquid crystal (LC) cavity in the middle layer. A dual fan-shaped direct current (DC) bias circuit is designed to minimize the interaction between the radio frequency (RF) signal and the DC source, allowing control of the LC dielectric constant via bias voltage. This enables multi-band operation to improve communication capacity and quality for x-band devices. The polarization conversion (PC) structure employs an orthogonal anisotropic design, utilizing logarithmic functions to create two pairs of bowtie microstrip patches for linear-to-circular polarization conversion (LCPC). Simulation results show that for x-polarized incident waves, with an LC dielectric constant of ε_r = 2.8, left- and right-handed circularly polarized (LHCP and RHCP) waves are achieved in the frequency ranges of 8.15–8.46 GHz and 9.84–12.52 GHz, respectively. For ε_r = 3.9, LHCP and RHCP are achieved in 9–9.11 GHz and 9.86–11.81 GHz, respectively, and for ε_r = 4.6, they are in 8.96–9.11 GHz and 9.95–11.51 GHz. In the case of y-polarized incident waves, the MS reflects the reverse CP waves within the same frequency ranges. Measured results show that at ε_r = 2.8, the axial ratio (AR) is below 3 dB in the frequency ranges 8.16–8.46 GHz and 9.86–12.48 GHz, with 3 dB AR relative bandwidth (ARBW) of 3.61% and 23.46%, respectively. For ε_r = 4.6, the AR < 3 dB in the frequency range of 9.78–11.34 GHz, with a 3 dB ARBW of 14.77%. Finally, the measured and simulated results are compared to validate the proposed design, which can be applied to various applications within the corresponding operating frequency band. Full article

This systematic review explores recent advancements in antenna and rectifier systems for radio frequency (RF) energy harvesting within the gigahertz frequency range, aiming to support the development of sustainable and efficient low-power electronic applications. Conducted under the PRISMA methodology, our review filtered 2465 initial records down to 80 relevant studies, addressing three research questions focused on antenna design, operating frequency bands, and rectifier configurations. Key variables such as antenna type, resonant frequency, gain, efficiency, bandwidth, and physical dimensions were examined. Antenna designs including fractal, spiral, bow-tie, slot, and rectangular structures were analyzed, with fractal antennas showing the highest efficiency, while array antennas exhibited lower performance despite their compact dimensions. Frequency band analysis indicated a predominance of 2.4 GHz and 5.8 GHz applications. Evaluation of substrate materials such as FR4, Rogers, RT Duroid, textiles, and unconventional composites highlighted their impact on performance optimization. Rectifier systems including Schottky, full-wave, half-wave, microwave, multi-step, and single-step designs were assessed, with Schottky rectifiers demonstrating the highest energy conversion efficiency. Additionally, correlation analyses using boxplots explored the relationships among antenna area, efficiency, operating frequency, and gain across design variables. The findings identify current trends and design considerations crucial for enhancing RF energy harvesting technologies. Full article

Poisoning and suffocation accidents occurred frequently in the pre-treatment pool workshops of biogas plants, so this paper provided a multi-dimensional risk analysis model: Bow-Tie-Qualitative Comparative Analysis (QCA)-Bayesian Neural Network-Consequence Simulation. First, the reasons for biogas poisoning and suffocation accidents were clarified through Bow-Tie. Then, the QCA method explored the accident cause combination paths in management. Next, the frequency distribution of biogas poisoning and suffocation accidents in the pre-treatment pool workshop was predicted to be 0.61–0.66 using the Bayesian neural network model, and the uncertainty of the forecast outcome was given. Finally, the ANSYS Fluent 16.0 simulation of biogas diffusion in three different ventilation types and a grid-independent solution of the simulation were conducted. The simulation results showed the distribution of methane, carbon dioxide and hydrogen sulfide gases and the hazards of the three gases to workers were analyzed. In addition, according to the results, this paper discussed the importance and necessity of ventilation in pre-treatment pool workshops and specified the hazard factors in biogas poisoning and suffocation accidents in the pre-treatment pool workshops. Some suggestions on gas alarms were also proposed. Full article

Background: Canine oral melanoma (COM) is an aggressive and often fatal neoplasm in dogs, with clinical and molecular similarities to human melanoma. Despite its relevance as a comparative oncology model, the molecular mechanisms underlying COM remain poorly understood. This study aimed to characterize gene expression profiles in COM to identify differentially expressed genes (DEGs), potential biomarkers, and therapeutic targets. Methods: In this pilot study, we performed RNA sequencing (RNA-seq) on tumor and healthy oral tissue samples from dogs. Two independent analytical pipelines—Bowtie2-DESeq2 and HISAT-StringTie-Ballgown—were used to ensure robustness in DEG detection. We also conducted pathway enrichment and isoform-level analyses to investigate biological processes and alternative splicing events. Results: Both approaches identified a core set of 929 common DEGs. Key oncogenic pathways, including MAPK/ERK and cell cycle regulation, were significantly affected, with notable upregulation of BRAF, NRAS, CDK4, and MITF (log2FC = 2.86, p < 0.001). The transcription factor SOX10 and the cytokine IL-33, both previously implicated in melanoma progression, were consistently overexpressed. Additionally, NF1, a known RAS pathway inhibitor, was also upregulated. Isoform analysis revealed novel transcript variants, suggesting a complex layer of post-transcriptional regulation in COM. Many DEGs remained uncharacterized, and chromosomal distribution analysis highlighted potential genomic influences. Conclusions: Our findings provide new insights into the molecular landscape of COM, reinforcing its utility as a model for human melanoma. The identification of conserved oncogenic pathways and novel transcript variants opens avenues for further functional studies and the development of targeted therapies in both veterinary and human oncology. Full article

DNA and RNA nucleotide sequences are ubiquitous in all biological cells, serving as both a comprehensive library of capabilities for the cells and as an impressive regulatory system to control cellular function. The multi-alignment framework (MAF) provided in this study offers a user-friendly platform for sequence alignment and quantification. It is adaptable to various research needs and can incorporate different tools and parameters for in-depth analysis, especially in low read rate scenarios. This framework can be used to compare results from different alignment programs and algorithms on the same dataset, allowing for a comprehensive analysis of subtle to significant differences. This concept is demonstrated in a small RNA case study. MAF is specifically designed for the Linux platform, commonly used in bioinformatics. Its script structure streamlines processing steps, saving time when repeating procedures with various datasets. While the focus is on microRNA analysis, the templates provided can be adapted for all transcriptomic and genomic analyses. The template structure allows for flexible integration of pre- and post-processing steps. MicroRNA analysis indicates that STAR and Bowtie2 alignment programs are more effective than BBMap. Combining STAR with the Salmon quantifier or, with some limitations, the Samtools quantification, appears to be the most reliable approach. This method is ideal for scientists who want to thoroughly analyze their alignment results to ensure quality. The detailed microRNA analysis demonstrates the quality of three alignment and two quantification methods, offering guidance on assessing result quality and reducing false positives. Full article

This paper presents a comparative analysis of performance for several antenna prototypes using a screen-printing process. This analysis was performed using various bow-tie antenna configurations, including single-band and multi-band antennas with linear or circular polarization over multiple operating frequency ranges. For antenna implementations, three different conductive inks and two resolutions of screen masks were tested. The performance of the fabricated prototypes has then been compared to the copper laser-etched antennas. This study revealed that with the proper selection of ink thinness, screen-printed bow-tie antennas achieve similar performances to copper laser-etched bow-tie antennas up to 6 GHz, even for linearly polarized and circularly polarized antennas. However, the printing resolution should be improved by reducing the ink thickness for bow-tie antennas at higher operating frequencies. The measurement results show a successful agreement after improving the printing resolution of the fabricated 5.8 GHz and 15 GHz bi-band bow-tie antennas. Full article

Noble metal nanostructures have garnered significant attention for their exceptional optical properties, particularly Localized Surface Plasmon Resonance (LSPR), which enables pronounced near-field electromagnetic enhancements. Among these, bowtie nanoantennas (BNAs) are distinguished by their intense plasmonic coupling within nanogap regions, making them highly effective for applications such as surface-enhanced Raman scattering (SERS). However, the practical utility of conventional BNAs is often hindered by small hotspot areas and significant scattering losses at their peak near-field enhancement wavelengths. To overcome these limitations, we have designed a novel notch metal-insulator-metal bowtie nanoantenna (NMIM-BNA) structure. This innovative design integrates dielectric materials with Ag-BNA nanostructures and strategically positions arrays of silver (Ag) nanorods within the central nanogap. By coupling the larger NMIM-BNA framework with these smaller Ag nanorod arrays, higher-order plasmon modes (often referred to as dark modes) are effectively excited. Consequently, the NMIM-BNA exhibits substantial electric field enhancement, particularly at the Fano dip wavelength, arising from the efficient coupling of these higher-order plasmon modes with dipole plasmon modes. Compared to conventional Ag-BNA nanoantennas, our NMIM-BNA provides a significantly larger hotspot region and an enhanced near-field amplification factor, underscoring its strong potential for advanced SERS applications. Full article

Bow-tie cavity configurations have gained significant attention due to their efficacy in facilitating stable resonator operation for applications requiring short pulse operation and high repetition rate pulses, offering versatility and reliability. While there is an extensive body of literature addressing the theoretical aspects and applications of this laser configuration, there exists a gap in practical insights and systematic approaches guidance pertaining to the development and precision alignment of this laser type. The paper achieves this by compiling a range of analytical and optimization techniques for the bow-tie cavity configuration and delineating the necessary steps for the optimization required for continuous wave operation. This ultimately leads to the attainment of the pulsed regime through the Kerr Lens Mode-locking technique, offering a detailed account of the development, optimization, and performance evaluation of a Ti:Sapphire femtosecond laser cavity, using dispersion-compensating mirrors to produce a low-energy pulse of 1 nJ, a high repetition rate of 1 GHz, and a short pulse duration of 61 fs. This work can be useful for researchers and engineers seeking to embark on the development of compact and high-performance femtosecond lasers for a spectrum of applications, encompassing biomedical imaging, laser-assisted surgery, spectroscopy, and optical frequency combs. Full article

In this paper, we explore the use of chip-scale blown glass microbubble structures for MEMS packaging applications. Specifically, we demonstrate the efficacy of this method of packaging for the improvement of the lifetime of a ferrofluid-based magnetoviscous magnetometer. We have previously reported on the novel concept of a ferrofluid based magnetometer in which the viscoelastic response of a ferrofluid interfacial layer on a high frequency shear wave quartz resonator is sensitively monitored as a function of applied magnetic field. The quantification of the magnetic field is accomplished by monitoring the at-resonance admittance characteristics of the ferrofluid-loaded resonator. While the proof-of-concept measurements of the device have been successfully made, under open conditions, the evaporation of the carrier fluid of the ferrofluid continuously changes its viscoelastic properties and compromises the longevity of the magnetometer. To prevent the evaporation of the ferrofluid, here, we seal the ferrofluid on top of the micromachined quartz resonator within a blown glass hemispherical microbubble attached to it using epoxy. The magnetometer design used a bowtie-shaped thin film Metglas (Fe₈₅B₅Si₁₀) magnetic flux concentrator on the resonator chip. A four-times smaller noise equivalent, a magnetic field of 600 nT/√Hz at 0.5 Hz was obtained for the magnetometer using the Metglas flux concentrator. The ferrofluid-based magnetometer is capable of sensing magnetic fields up to a modulation frequency of 40 Hz. Compared with the unsealed ferrofluid device, the lifetime of the glass microbubble integrated chip packaged device improved significantly from only a few hours to over 50 days and continued. Full article

For gene expression analysis in complex microbiomes, utilizing both metagenomic and metatranscriptomic reads from the same sample enables advanced functional analysis. Due to their diversity, metagenomic contigs are often used as reference sequences instead of complete genomes. However, studies optimizing mapping strategies for both read types remain limited. In addition, although transcripts per million (TPM) is commonly used for normalization, few studies have evaluated the influence of ribosomal RNA (rRNA) in metatranscriptomic reads. This study compared Burrows–Wheeler Aligner–Maximal Exact Match (BWA-MEM) and Bowtie2 as mapping tools for metagenomic contigs. Even after optimizing Bowtie2 parameters, BWA-MEM showed higher efficiency in mapping both metagenomic and metatranscriptomic reads. Further analysis revealed that rRNA sequences contaminate predicted protein-coding regions in metagenomic contigs. When comparing TPM values across samples, contamination by rRNA led to an overestimation of TPM changes. This effect was more pronounced when the difference in rRNA content between samples was larger. These findings suggest that metatranscriptomic reads mapped to rRNA should be excluded before TPM calculations. This study highlights key factors influencing read mapping and quantification in gene expression analysis of complex microbiomes. The findings provide insights for improving analytical accuracy and advancing functional studies using both metagenomic and metatranscriptomic data. Full article

This study reports two novel species, Gogorevia contracta sp. nov. and G. recticentralis sp. nov., which were isolated from freshwater environments in South Korea. Using an integrative taxonomic approach, we conducted morphological analyses using light microscopy and scanning electron microscopy, along with molecular phylogenetic investigations using SSU rRNA and rbcL gene sequences. Phylogenetic reconstructions highlighted the distinct characteristics of both species, confirming their classification within the genus Gogorevia and elucidating their evolutionary relationships. Morphologically, G. contracta was characterized by a bow-tie-shaped central area and circular depressions in the rapheless valve, whereas G. recticentralis exhibited a rectangular-to-wedge-shaped central area with parallel striae near the center of the raphe valve. Our findings highlighted the ecological significance of Gogorevia species and suggested their potential role as bioindicators of water quality in relatively unpolluted freshwater systems. Over the past decade, our research has focused on the taxonomic and ecological study of diatoms in the Han River system and identified 136 species, including nine newly described taxa. The findings of the present study contribute to a growing understanding of Gogorevia diversity, underscore the importance of region-specific diatom indices, and support the integration of morphological and molecular methods into diatom systematics. Full article

Microwave Bow-Tie Diodes operate across a broad frequency range, including THz radiation detection and THz imaging applications. When fabricated using modulation-doped structures, these diodes exhibit enhanced detection properties that are best characterized by voltage sensitivity. The sensitivity is influenced by multiple factors, including diode design, semiconductor material quality, and the characteristics of the ohmic contacts. In this study, we examine how the electrical properties of modulation-doped bow-tie diodes are affected by their orientation relative to the crystallographic axes. Extensive investigations on various bow-tie diodes exposed to broadband microwave radiation, both in darkness and under white and infrared light illumination, enabled us to identify the optimal diode designs and illumination conditions for maximizing sensitivity to electromagnetic radiation. Based on our findings, we provide recommendations for diode design and illumination conditions to enhance the diode’s sensitivity to microwave radiation while minimizing illumination-induced effects on electrical properties. Full article

A novel frequency-selective polarization converter (FSPC) is proposed based on the new method of combining a polarization conversion metasurface (PCM) with a bandpass frequency-selective surface (FSS), which provides an efficient transmission band and broadband radar cross-section (RCS) reduction. The upper and lower layers are combined to form the proposed FSPC. In the upper layer design, the bowtie-shaped structure is used to achieve polarization conversion on both sides of the transmission band. Regarding the lower layer design, the second-order bandpass FSS is employed, which acts as an equivalent ground for the polarization conversion layer outside the passband and provides a highly efficient transmission window within the passband. Ultimately, the magnitude of the co-polarized reflection of the FSPC that is below −10 dB ranges from 5.1 GHz to 16.1 GHz, with a relative bandwidth of 104%, and the co-polarized transmission window with an insertion loss of less than 1 dB is presented ranging from 8.7 GHz to 12.6 GHz, with a relative bandwidth of 36%. Furthermore, by arranging the upper bowtie-shaped PCM in a checkerboard pattern, the monostatic RCS can be effectively reduced in a broad frequency range. Samples of the proposed design are fabricated for the measurement verification of performance. The results show that the measurement results match well with the simulation results. Compared with other designs, the proposed FSPC exhibits efficient co-polarized transmission, with insertion loss as low as 0.34 dB and the passband flatness being good. Full article

To solve the problems of numerous influencing factors, such as the high uncertainty and leakage risk of gas production pipelines in high-sulfur gas fields, a dynamic analysis of a gas production pipeline’s leakage risk using a dynamic Bayesian network is proposed. By means of Bow-tie model analysis, the primary risk sources of gas pipeline leakage and different accidents are summarized. A temporal dimension was introduced to construct a dynamic Bayesian network model, utilizing the Leaky noisy-OR gate model to rectify and compute conditional probability, thereby facilitating dynamic risk prediction of gas pipeline leakage. Taking the first section of the pipeline of a municipal gas collection station as an example, with the help of GeNIe 4.0 Academic software, the influence degree of each basic event on pipeline gas leakage was revealed. The change curve of gas leakage probability over time was drawn, and the occurrence probability of potential consequences of accidents was computed. The results indicate that the status of flanges, valves, and pipelines are key factors in determining the occurrence of gas leakage accidents, and six risk sources, including medium corrosion in gas leakage accidents, were determined, with these having practical conspicuousness for strengthening the leakage protection of gas pipelines and providing proper support for the formulation of relevant safety measures. Full article

To enhance the capability of a ground penetrating radar (GPR) in subsurface target identification and improve its polarization sensitivity in detecting underground linear objects, a circularly polarized broadband composite spiral antenna was designed. This antenna integrates equiangular spiral and Archimedean spiral structures, achieving a wideband coverage of 1–5 GHz with stable circular polarization characteristics. The antenna employs an exponentially tapered microstrip balun for impedance matching and a metallic-backed cavity filled with absorbing materials to enhance its directivity. Experimental results demonstrate excellent radiation performance and stable circular polarization characteristics, with the axial ratio consistently below 3 dB throughout the operating frequency band, highlighting its suitability for polarimetric GPR systems. Furthermore, a 3D GPR measurement using the designed antenna validates its improved capacity for detecting subsurface linear objects, compared to the conventional linearly polarized bowtie antenna. Full article