Search Results (302)

When monitoring seed positions in soil using ultrasonic waves, the main challenge is obtaining acoustic wave characteristics at the seed locations. This study developed a three-dimensional ultrasonic model with the double media of seed–soil using the discrete element method to visualize signal variations and analyze propagation characteristics. The effects of the compression ratio (0/6/12%), excitation frequency (20/40/60 kHz), and amplitude (5/10/15 μm) on signal variation and attenuation were analyzed. The results show consistent trends: time/frequency domain signal intensity increased with a higher compression ratio and amplitude but decreased with frequency. Comparing ultrasonic signals at soil particles before and after the seed along the propagation path shows that the seed significantly absorbs and attenuates ultrasonic waves. Time domain intensity drops 93.99%, and first and residual wave frequency peaks decrease by 88.06% and 96.39%, respectively. Additionally, comparing ultrasonic propagation velocities in the double media of seed–soil and the single soil medium reveals that the velocity in the seed is significantly higher than that in the soil. At compression ratios of 0%, 6%, and 12%, the sound velocity in the seed is 990.47%, 562.72%, and 431.34% of that in the soil, respectively. These findings help distinguish seed presence and provide a basis for ultrasonic seed position monitoring after sowing. Full article

Studies underscore the significance of coir fibers as a sustainable building material. Based on these insights, this research aims to evaluate coir fiber composite panels of various thicknesses as eco-friendly sound absorbing alternatives to synthetic construction materials like rockwool and fiberglass, aligning its use with the United Nations Sustainable Development Goals. Acoustic absorption was quantified with an impedance tube, and subsequent simulations compared the performance of coir composite panels with that of conventional materials, which constitutes an underexplored evaluation. Using 10 receiver points, the simulations reproduced the acoustic conditions of a multipurpose auditorium before and after the coir covering of parts of the rear and posterior walls. The results indicate that when coir coverings account for approximately 10% of the auditorium surface, reverberation times at 250, 500, 2000, and 4000 Hz are reduced by roughly 1 s. Furthermore, the outcomes reveal that early reflections occur more rapidly in the coir-enhanced model, while the values of the early decay time parameter decrease across all receiver points. Although the original configuration had poor speech clarity, the modified model achieved optimal values at all the measurement locations. These findings underscore the potential of coir fiber panels in enhancing acoustic performance while fostering sustainable construction practices. Full article

It is vital to stabilize pillar dams in underground reservoirs in coal mine goafs to protect groundwater resources and quarry safety, practice green mining, and protect the ecological environment. Considering the actual occurrence of coal pillar dams in underground reservoirs, acoustic emission (AE) mechanical tests were performed on dry, naturally absorbed, and soaked coal samples. According to the mechanical analysis, Quantitative analysis revealed that dry samples exhibited the highest mechanical parameters (peak strength: 12.3 ± 0.8 MPa; elastic modulus: 1.45 ± 0.12 GPa), followed by natural absorption (peak strength: 9.7 ± 0.6 MPa; elastic modulus: 1.02 ± 0.09 GPa), and soaked absorption showed the lowest values (peak strength: 7.2 ± 0.5 MPa; elastic modulus: 0.78 ± 0.07 GPa). The rate of mechanical deterioration increased by ~25% per 1% increase in moisture content. It was identified that the internal crack development presented a macrofracture surface initiating at the sample center and expanding radially outward, and gradually expanding to the edges by adopting AE seismic source localization and the K-means clustering algorithm. Soaked absorption was easier to produce shear cracks than natural absorption, and a higher water content increased the likelihood. The b-value of the AE damage evaluation index based on crack development was negatively correlated with the rock damage state, and the S-value was positively correlated, and both effectively characterized it. The research results can offer reference and guidance for the support design, monitoring, and warning of coal pillar dams in underground reservoirs. (The samples were tested under two moisture conditions: (1) ‘Soaked absorption’—samples fully saturated by immersion in water for 24 h, and (2) ‘Natural absorption’—samples equilibrated at 50% relative humidity and 25 °C for 7 days). Full article

Noise reduction for manufacturing enterprises is favorable for workers because it relieves occupational diseases and improves productivity. An acoustic metamaterial with parallel, unequal cavities is proposed and optimized, aiming to achieve an optimal broadband sound absorber in the low–frequency range with a limited total thickness. A theoretical model for the acoustic metamaterial of a hexagonal column with 6 triangular cavities and 12 right–angled trapezoidal cavities was established. The lengths of these embedded apertures were optimized using the particle swarm optimization algorithm, with initial parameters obtained from acoustic finite element simulation. Additionally, the impacts of manufacturing errors on different regions were analyzed. The experimental results prove that the proposed acoustic metamaterials can achieve an average absorption coefficient of 0.87 from 384 Hz to 667 Hz with a thickness of 50 mm, 0.83 from 265 Hz to 525 Hz with a thickness of 70 mm, and 0.82 from 156 Hz to 250 Hz with a thickness of 100 mm. The experimental validation demonstrates the accuracy of the finite element model and the effectiveness of the optimization algorithm. This extensible acoustic metamaterial, with excellent sound absorption performance in the low-frequency range, can be mass-produced and widely applied for noise control in industries. Full article

Lightweight powder-based sound-absorbing materials are characterized by sound absorption peaks at lower frequencies compared to other sound absorption materials of the same thickness. This behavior is attributed to the excitation of longitudinal vibration modes in the powder particles by incident sound waves, wherein acoustic energy is converted into kinetic energy and subsequently dissipated through interparticle interactions. These lightweight, fine powders are artificially engineered acoustic materials. Despite their structural simplicity, they exhibit emergent and complex sound absorption behaviors through fundamental vibrational mechanisms. Representing the powder layer with a transfer matrix simplifies model-based development and enhances versatility as an acoustic element. The powder layer was modeled as a longitudinally oscillating 1D beam, and transfer matrix of the powder layer was derived. To verify the obtained transfer matrix, the experimental values were compared with the theoretical values for a single powder layer. In addition, both were compared for the case of other acoustic elements stacked on top of each other, which were close to each other. The theoretical values were compared with the experimental values, which were close to each other. Full article

The propagation of high-frequency ultrasound waves will generate both physical and chemical effects as they propagate through a liquid medium, such as acoustic streaming, an acoustic fountain, and atomization. These phenomena are believed to be the main factors that contribute to the enhancement of mass transfer in the gas–liquid carbon dioxide (CO₂) absorption system. Computational Fluid Dynamic (CFD) simulation is one of the powerful tools that can be used to model the complex hydrodynamic behavior induced by the propagation of ultrasound waves in the liquid medium. In this study, the ultrasonic irradiation forces were simulated via the momentum source term method using commercial CFD software (ANSYS Fluent V19.1). In addition, a parametric study was conducted to investigate the influences of absorber height and ultrasonic power on the hydrodynamic mixing performance. The simulation results indicated that enhanced mixing and a higher intensification factor were achieved with increased fountain flow velocity, particularly at the lowest absorber height and highest ultrasonic power. Conversely, the energy efficiency was improved with the increase of absorber height and decrease of ultrasonic power. To determine the optimal combination of absorber height and ultrasonic power, this trade-off between the energy efficiency and intensification in the ultrasonic-assisted absorption system (UAAS) is a crucial consideration during process scale-up. Full article

Nowadays, natural fiber-based materials are widely used in the building sector, where the use of green and sustainable products is of growing interest. One of these fibrous materials is the esparto, a plant belonging to the Gramineae family, with a height up to 1 m. It grows in arid places with scarce rainfall, being common in some areas of the Iberian Peninsula. Due to its morphology, it can be used to replace conventional materials used in soundproofing and building applications. In this work, the acoustic properties of esparto fibers are studied using impedance tube measurements and via a phenomenological acoustic model where the input parameters are some non-acoustic properties such as porosity, density, tortuosity, and flow resistivity. The experimental results obtained showed the good acoustic performance of esparto fibers, with a high sound absorption coefficient along the usual frequency bandwidth. Furthermore, the theoretical results obtained using the phenomenological model exhibited a strong correlation with the sound absorption spectra obtained through experimental measurements. Full article

This study investigates the effectiveness of sloped horizontal shading fins in enhancing visual comfort, electricity generation, and acoustic attenuation in a south-facing office room in Wrocław, Poland (51° latitude). A simulation-based approach combined Radiance daylight simulations, PV energy modeling, and graphical acoustic analysis. Four fin configurations were tested to identify the optimal design. The results indicate that Variant 3, featuring two 1 m wide fins inclined at 45°, achieved the best overall performance, increasing UDI_{300–3000/168} from 53.1% to 95.8%, reducing DGP from 50% to 27%, and enabling an estimated annual electricity production of 4.67 MWh. Additionally, applying sound-absorbing material on the shaded side of the fins significantly reduced reflective acoustic wave bounces, significantly reducing façade-exposed noise. This multifunctional solution demonstrates a practical and scalable strategy for improving office environmental quality in temperate climates, contributing to energy efficiency, acoustic comfort, and visual well being. Full article

The percentage of historical heritage buildings in Italy is substantial. Many of these buildings are abandoned or not adequately restored for public access due to safety concerns. However, some are managed by city councils and made available to local communities. These heritage buildings, valued for their historical significance, are now frequently used for live events, including musical performances by ensembles and small groups. This paper deals with the acoustics of two rooms provided with barrel-vaulted ceilings: Sisto V Hall in Naples and Aula Magna at the University of Parma. These spaces are structurally very similar, differing mainly in length. Acoustic measurements conducted in both halls reveal reverberation times of approximately 4.5 s at mid frequencies, resulting in poor speech clarity. This is primarily due to the presence of reflective surfaces, as the walls and ceilings are plastered, and the floors are tiled. To optimize their acoustic properties for functions such as celebrations, gatherings, and conferences, an acoustic design intervention was proposed. Digital models of the halls were calibrated and used to correct the acoustics by incorporating absorbing panels on the walls and carpeting on the floors of the central walk path. This treatment successfully balanced the reverberation time to approximately 1.3–1.4 s at mid frequencies, making speech more intelligible. Additionally, an amplified audio system was analyzed to enhance sound distribution, ensuring uniform coverage, even in the last rows of seating. Under amplified conditions, sound pressure levels (SPLs) range between 90 dB and 93 dB, with appropriate gain control applied to the column array speakers. Full article

This study was conducted to improve the sound absorption dips in nonwoven fabric sheets with a back air space. Considering the particle velocity distribution in the back air space, another nonwoven sheet was added to divide the air space into layers. The sound absorption coefficient of the sound-absorbing structure was theoretically derived using the transfer matrix method. The nonwoven sheet model with the Rayleigh model and the air space behind the nonwoven sheet were mathematically represented using the transfer matrix. The transfer function method was employed to combine the transfer matrices to obtain the sound absorption coefficient. A two-microphone acoustic impedance tube was used to measure the sound absorption coefficient, and the theoretical and experimental values were compared. The sound absorption dip of the first order was improved by placing a nonwoven sheet at a position half the thickness of the back air space. It was theoretically predicted that placing the nonwoven sheet at 1/4 of the back air space thickness from the rigid wall would improve the first- and second-order sound absorption dips. By selecting the conditions, a similar trend was observed during the experiments. The study shows that the higher the ventilation resistance of the added nonwoven fabric sheet, the more improved the sound absorption dip. Full article

Material removal processes such as milling, drilling, and turning often generate harmful vibrations that can negatively impact both machine performance and operator safety. Addressing these vibrations at their source or reducing them to safe levels is, therefore, a critical challenge. This study proposes a practical solution by introducing thin-fin-type vibration-absorbing devices fabricated using 3D printing technology. These devices are designed specifically to mitigate vibration propagation during milling operations. To evaluate their effectiveness, a multi-sensor system comprising sound level meters, a vibrometer, and a vision–acoustic camera was employed to measure sound levels. The results show that the use of fabricated devices can reduce noise levels significantly, from 93 dB (comparable to power tools or a lawn mower) to 74 dB (similar to normal conversation or a busy office). This substantial reduction demonstrates the potential of the proposed devices to enhance workplace safety and acoustic comfort on the shop floor. Full article

Balancing ventilation and broadband sound insulation remains a significant challenge in noise control engineering, particularly when simultaneous airflow and broadband noise reduction are required. Conventional porous absorbers and membrane-type metamaterials remain fundamentally constrained by ventilation-blocking configurations or narrow operational bandwidths. This study presents a ventilated composite metamaterial unit (VCMU) co-integrating optimized labyrinth channels and the Helmholtz resonators within a single-plane architecture. This design achieves exceptional ventilation efficiency through a central flow channel while maintaining sub-λ/30 thickness (λ/31 at 860 Hz). Coupled transfer matrix modeling and finite-element simulations reveal that Fano–Helmholtz resonance mechanisms synergistically generate broadband transmission loss (STL) spanning 860–1634 Hz, with six STL peaks in the 860 and 1634 Hz bands (mean 18.4 dB). Experimental validation via impedance tube testing confirmed excellent agreement with theoretical and simulation results. The geometric scalability allows customizable acoustic bandgaps through parametric control. This work provides a promising solution for integrated ventilation and noise reduction, with potential applications in building ventilation systems, industrial pipelines, and other noise-sensitive environments. Full article

The duration of water immersion significantly affects the mechanical response of rock materials. This study investigated the weakly cemented sandstone from the Wulagen Open-pit Mine to examine how varying immersion times affected the mineral composition, micro-porous structure, and macro-mechanical properties of the sandstone. The current study aimed to explore the mechanisms underlying the degradation of the strength and deformability of sandstone due to prolonged water exposure. The analysis showed that immersion time notably influenced the pore structure as well as the mineralogical characteristics of weakly cemented sandstone. These changes were the primary factors leading to alterations in its mechanical properties and failure modes. Specifically, with increasing immersion time, clay minerals absorbed water and expanded, with the most significant expansion occurring between 30 and 60 days. This rapid internal crack growth led to an exponential decrease in compressive strength and elastic modulus, with the most significant decline occurring between 30 and 60 days. The failure mode of the sandstone transitioned from extensional fracture to shear failure. Acoustic emission analysis revealed that, in the dry state, tensile cracks were about three times more prevalent than shear cracks, while after 60 days of immersion, shear cracks accounted for over 80%. After 60 days of immersion, microscopic cracks were fully interconnected, and the mechanical properties of the sandstone showed minimal change, with shear failure becoming predominant. These experimental results provide theoretical guidance for preventing the collapse of slopes composed of weakly cemented rock under long-term immersion conditions. Full article

Membranes can be used in different ways to achieve improvements in sound absorption. They can be used on top of base materials (sound-absorbing materials or other kinds) in such a way that they barely increase the thickness while increasing the sound absorption. They can be positioned inside a sandwich structure for the same purpose. They can also be used independently. There are thin membranes with different characteristics (perforated or otherwise, made up of different thin layers, fabrics made of different yarns, etc.) that are applied to surfaces with a plenum chamber. In all of these foregoing cases it can be difficult to characterise the membrane. Membranes with a smaller thickness lead to difficulties in the positioning of measuring devices thereby increasing the test error. The aim of this work is to obtain airflow resistance and the characteristic acoustic impedance of membranes in a more stable manner. Measurements of the airflow resistance and the characteristic acoustic impedance of sandwich structures with inserted membranes are considered for this purpose. The base material comprising the sandwich was characterised prior to these measurements. These measurements indirectly produce the airflow resistance and the characteristic acoustic impedance of the membrane. The results obtained show more stable measurements of the airflow resistance and the obtaining of the characteristic acoustic impedance of the membrane under the conditions in which it is set. Full article

Based on the three-parameter approximate JCAL analytical model (hereinafter referred to as the three-parameter model), this study conducted an in-depth analysis of the effects of porosity, median pore size, and pore size standard deviation on the acoustic performance of porous materials and developed a composite porous material composed of glass fibers and zeolite particles. Experimental results indicate that the pore size distribution significantly affects the acoustic performance of fibrous porous sound-absorbing materials. Specifically, smaller pores lead to better sound absorption at mid–low frequencies, with the optimal sound absorption performance observed when the median pore size is between 60 and 80 μm. Increasing the material density and decreasing the fiber diameter help reduce the internal pore size, thereby improving the material’s sound absorption performance. Additionally, the appropriate addition of zeolite can further optimize the internal pore size and effective sound-absorbing interface, thus enhancing the material’s sound absorption performance. When the material density is 120 kg/m³ and the zeolite substitution rate is around 10%, the material exhibits the best acoustic performance, with a noise reduction coefficient (NRC) reaching 0.65, which is a 10.17% increase compared to the material without zeolite. Comparing the simulation data from the three-parameter model with the actual measurement data shows that the model has excellent predictive performance for the sound absorption coefficient (SAC) of single-fiber porous materials (with an error of approximately 5%). However, for composite porous materials, due to the complex changes in interfaces, there is a certain prediction error (with the maximum error reaching 12.81%), indicating that the model needs further optimization and correction when applied to composite materials. Full article