sensors-logo

Journal Browser

Journal Browser

UHF and RF Sensor Technology for Partial Discharge Detection

A special issue of Sensors (ISSN 1424-8220). This special issue belongs to the section "Physical Sensors".

Deadline for manuscript submissions: closed (31 December 2018) | Viewed by 130279

Special Issue Editors


E-Mail Website
Guest Editor
Department of Electrical, Electronic and Automation Engineering and Applied Physics, Escuela Técnica Superior de Ingeniería y Diseño Industrial (ETSIDI), Universidad Politécnica de Madrid, Ronda de Valencia 3, 28012 Madrid, Spain
Interests: partial discharges; power transformers; electrical insulation diagnosis; dielectrics; antennas; renewable energy
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
High Frequency Diagnostics and Engineering Ltd, Glasgow, UK
Interests: partial discharges; condition monitoring; UHF sensors; energy harvesting
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
Department of Electrical Engineering, Universidad Carlos III de Madrid, Avda. Universidad, 30, 28911 Leganés, Spain
Interests: sensor design; measurement and instrumentation techniques; signal processing; partial discharges measurement, identification and localization; identification of partial discharges sources and noise rejection
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
Department of Engineering and Technology, School of Computing and Engineering, University of Huddersfield, Huddersfield HD1 3DH, UK
Interests: partial discharges; condition monitoring; sensors; antennas; propagation; AI-based detection techniques; fault diagnosis
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

Condition monitoring (CM) of high-voltage (HV) insulation systems is essential for establishing a correct diagnosis regarding the health of these costly and safety-critical industrial assets, as well as for implementing practical condition-based-maintenance (CBM) regimes. The assets being monitored may include rotating machines, power transformers, HV cables and accessories, air-insulated-substations (AIS), gas-insulated-switchgear (GIS) and overhead lines. Recent advances have seen widespread development of non-contact electromagnetic wave sensors for detecting and locating partial discharges and electrical arcs. These sensors play an important role in periodic testing, continuous monitoring or ‘fingerprinting’ of RF emissions from HV equipment. Practical applications of UHF and other RF techniques are leading to the development of new sensors and associated solutions for signal acquisition, processing, analysis and interpretation, which in turn require new approaches to decision making about the condition of assets being monitored.

The aim of this Special Issue is to report on recent advances relating to the following themes: (1) non-contact electromagnetic sensors (RF, UHF, near field, electric, magnetic, etc.) used for detecting signals emitted by insulation defects either internally, or external to the equipment in question; (2) practical methods for integrating these sensors into real equipment for use in condition monitoring; (3) case studies and examples of implementation of the techniques in an industrial or laboratory setting; (4) sensor models to support the design process or for predicting their response (using data-driven modeling approaches, for example); and (5) bridging the gap between condition monitoring research and subsequent decision making using these technologies, possibly in combination with other monitoring parameters.

Prof. Dr. Ricardo Albarracín
Prof. Dr. Martin D. Judd
Prof. Dr. Guillermo Robles
Prof. Dr. Pavlos Lazaridis
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Sensors is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Partial Discharges
  • Condition Monitoring
  • UHF
  • Sensors
  • IEC TS 62478:2016, antennas, electrical insulation, localization

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (20 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Jump to: Review

14 pages, 4632 KiB  
Article
Variability of the UHF Signals Generated by Partial Discharges in Mineral Oil
by Michal Kunicki
Sensors 2019, 19(6), 1392; https://doi.org/10.3390/s19061392 - 21 Mar 2019
Cited by 18 | Viewed by 3375
Abstract
The paper presents the results of the analysis on the variability of the ultra-high frequency (UHF) signals generated by partial discharges (PD) under the long-term AC voltage. Surface PD (SD) are generated by model PD source (PDS) immersed in brand new mineral oil. [...] Read more.
The paper presents the results of the analysis on the variability of the ultra-high frequency (UHF) signals generated by partial discharges (PD) under the long-term AC voltage. Surface PD (SD) are generated by model PD source (PDS) immersed in brand new mineral oil. Three scenarios are compared and investigated, where different solid dielectrics are applied: pressboard paper (PBP), polytetrafluoroethylene (PTFE) and glass-ceramic (GLS). The PDS is powered continuously by the AC voltage with its relative level of 1.3 of the inception voltage (Ui) within 168 h. UHF signals generated by the continuously occurred SD within 168 h are registered. Various indicators describing the variability of the UHF signals emitted by SD are assigned and analyzed in order to discover if there are any relevant trends presented. Furthermore, some long-term characteristics of the UHF signals emitted by the applied PDS are also announced. As a result, some relevant trends are discovered and related to the properties of the applied dielectric materials, thus the variability of the UHF signals emitted by SD is confirmed. The highest variability of the UHF signals is associated with PBP and the first 48 h after PD inception. Moreover achieved results may be potentially applied for modeling of the PD variability in time, which may be useful for works that concern the development of the UHF method. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

16 pages, 7543 KiB  
Article
Partial Discharge Detection Using a Spherical Electromagnetic Sensor
by Pietro Romano, Antonino Imburgia and Guido Ala
Sensors 2019, 19(5), 1014; https://doi.org/10.3390/s19051014 - 27 Feb 2019
Cited by 47 | Viewed by 8808
Abstract
The presence of a partial discharge phenomenon in an electrical apparatus is a warning signal that could determine the failure of the insulation system, terminating the service of the apparatus and/or the network. In this paper, an innovative partial discharge (PD) measurement instrument [...] Read more.
The presence of a partial discharge phenomenon in an electrical apparatus is a warning signal that could determine the failure of the insulation system, terminating the service of the apparatus and/or the network. In this paper, an innovative partial discharge (PD) measurement instrument based on an antenna sensor is presented and analyzed. Being non-intrusive is one of the most relevant features of the sensor. The frequency response of the antenna sensor and the features to recognize different PD sources and automatically synchronize them with the supply voltage are described and discussed in details. The results show the performance of the instrument can make a fast and correct diagnosis of the health state of insulation systems. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

21 pages, 24573 KiB  
Article
A Sensor System for Detecting and Localizing Partial Discharges in Power Transformers with Improved Immunity to Interferences
by Petr Drexler, Martin Čáp, Pavel Fiala, Miloslav Steinbauer, Radim Kadlec, Miloš Kaška and Lubomír Kočiš
Sensors 2019, 19(4), 923; https://doi.org/10.3390/s19040923 - 22 Feb 2019
Cited by 23 | Viewed by 5027
Abstract
The paper reports on the solution, principles, and application results related to a system for diagnosing main transformers in power plants via the radiofrequency method. The subject of the diagnostics is the occurrence of partial discharge activity in transformers. The technical solution of [...] Read more.
The paper reports on the solution, principles, and application results related to a system for diagnosing main transformers in power plants via the radiofrequency method. The subject of the diagnostics is the occurrence of partial discharge activity in transformers. The technical solution of the system is characterized in the introductory section of the article. There then follows a description of the operating principle and the implemented novel advanced methods for signal detection and source localization. The results obtained from practical application of the system within the diagnostics of high-power transformers are presented as well. Because ambient electromagnetic disturbance was recognized as a major issue during the system development, novel detection methods were proposed, implemented, and verified. The principal approach utilizes an external radiofrequency sensor to detect outer impulse disturbance and to eliminate disturbance-triggered acquisitions, and it also ensures direct real-time visualization of the desired impulse signals. The ability of weak signal detection was verified via artificial impulse signal injection into the transformer. The developed detection methods were completed with localization techniques for signal source estimation. The desired impulse signal was detected and localized during full operation of the main transformer, despite the presence of strong electromagnetic interference. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Graphical abstract

17 pages, 11224 KiB  
Article
A Novel Antenna for Partial Discharge Measurements in GIS Based on Magnetic Field Detection
by Armando Rodrigo-Mor, Fabio Andrés Muñoz and Luis Carlos Castro-Heredia
Sensors 2019, 19(4), 858; https://doi.org/10.3390/s19040858 - 19 Feb 2019
Cited by 16 | Viewed by 5327
Abstract
This paper presents a new concept for partial discharge measurements in gas insulated systems (GIS). The proposed technique uses a novel GIS magnetic antenna that measures the magnetic field produced by partial discharges (PD) propagating in GIS. The foundations of the measurement technique [...] Read more.
This paper presents a new concept for partial discharge measurements in gas insulated systems (GIS). The proposed technique uses a novel GIS magnetic antenna that measures the magnetic field produced by partial discharges (PD) propagating in GIS. The foundations of the measurement technique and the magnetic antenna design are presented together with laboratory measurements. The magnetic antenna performance and the sensitivity of the acquisition system are studied. The bandwidth of the measurement system is in the high frequency and very high frequency (HF–VHF) range. Laboratory experiments demonstrate the suitability of the novel magnetic antenna-based measuring system for PD in GIS for corona, surface discharges, and free moving particles in SF6. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

16 pages, 19819 KiB  
Article
Design and Development of a Bio-Inspired UHF Sensor for Partial Discharge Detection in Power Transformers
by Luiz A. M. M. Nobrega, George V. R. Xavier, Marcus V. D. Aquino, Alexandre J. R. Serres, Camila C. R. Albuquerque and Edson G. Costa
Sensors 2019, 19(3), 653; https://doi.org/10.3390/s19030653 - 5 Feb 2019
Cited by 46 | Viewed by 5830
Abstract
In this paper, the design and development of a bio-inspired UHF sensor for partial discharge detection in power transformers is presented. The UHF sensor was developed for external use in dielectric windows of power transformers. For this purpose, a microstrip antenna was designed [...] Read more.
In this paper, the design and development of a bio-inspired UHF sensor for partial discharge detection in power transformers is presented. The UHF sensor was developed for external use in dielectric windows of power transformers. For this purpose, a microstrip antenna was designed with a radiating element shape based on the leaf of the Jatropha mollissima (Pohl) Baill plant. Then, an epoxy coating and an aluminium enclosure were developed to protect the antenna against corrosion and to provide mechanical support, external noise immunity, and a lifetime compatibility with power transformers. In order to verify the electrical parameters of the developed sensor, measurements of the gain and the reflection coefficient were performed in an anechoic chamber. Lastly, the antenna sensitivity for denominated partial discharge (PD) detection was compared with the IEC 60270 standard method. For this purpose, simultaneous tests were carried out in a partial discharge generator setup, composed of an oil cell with needle-plane electrodes. The experimental tests demonstrated the effectiveness of the sensor for detecting PD signals with apparent charge values higher than 35 pC. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

15 pages, 5790 KiB  
Article
Bio-inspired Printed Monopole Antenna Applied to Partial Discharge Detection
by Josiel do Nascimento Cruz, Alexandre Jean René Serres, Adriano Costa de Oliveira, George Victor Rocha Xavier, Camila Caroline Rodrigues de Albuquerque, Edson Guedes da Costa and Raimundo Carlos Silverio Freire
Sensors 2019, 19(3), 628; https://doi.org/10.3390/s19030628 - 1 Feb 2019
Cited by 44 | Viewed by 6512
Abstract
A new, bio-inspired printed monopole antenna (PMA) model is applied to monitor partial discharge (PD) activity in high voltage insulating systems. An optimized sensor was obtained by designing a PMA in accordance with the characteristics of the electromagnetic signal produced by PD. An [...] Read more.
A new, bio-inspired printed monopole antenna (PMA) model is applied to monitor partial discharge (PD) activity in high voltage insulating systems. An optimized sensor was obtained by designing a PMA in accordance with the characteristics of the electromagnetic signal produced by PD. An ultra-wideband (UWB) antenna was obtained by applying the truncated ground plane technique. The patch geometry was bio-inspired by that of the Inga Marginata leaf, resulting in a significant reduction in size. To verify the operating frequency and gain of the PMA, measurements were carried out in an anechoic chamber. The results show that the antenna operating bandwidth covers most of the frequency range of PD occurrence. Moreover, the antenna presented a good sensitivity (mean gain of 3.63 dBi). The antenna performance was evaluated through comparative results with the standard IEC 60270 method. For this purpose, simultaneous tests were carried out in a PD generator arrangement, composed by an oil cell with point-to-plane electrode configurations. The developed PMA can be classified as an optimized sensor for PD detection and suitable for substation application, since it is able to measure PD radiated signals with half the voltage levels obtained from the IEC method and is immune to corona discharges. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

12 pages, 6527 KiB  
Article
A Novel Approach for Partial Discharge Measurements on GIS Using HFCT Sensors
by Armando Rodrigo Mor, Luis Carlos Castro Heredia and Fabio Andres Muñoz
Sensors 2018, 18(12), 4482; https://doi.org/10.3390/s18124482 - 18 Dec 2018
Cited by 25 | Viewed by 7047
Abstract
This paper presents a novel measuring system for partial discharge (PD) measurements in Gas Insulated Systems (GIS) using high frequency current transformers (HFCT). The system is based on the measurement of the induced PD currents in the GIS enclosure. In opposition to the [...] Read more.
This paper presents a novel measuring system for partial discharge (PD) measurements in Gas Insulated Systems (GIS) using high frequency current transformers (HFCT). The system is based on the measurement of the induced PD currents in the GIS enclosure. In opposition to the existing antenna technologies that measure the radiated energy in the very high frequency/ultra-high frequency (VHF/UHF) range, the proposed system measures the PD conducted currents in the high frequency (HF) range and below. The foundation of the measurements together with a detailed explanation of the sensor installed conveniently at the bolts of the GIS spacer are presented. An experimental study on the current distribution in the GIS enclosure is described to evaluate the impact of the sensor on the measurements. Laboratory experiments have been performed that show the suitability of this method to properly measure particle discharges caused by corona, surface and free moving particle discharges in SF6. Discharges in the range of 1 to 4 pC have been properly measured. An analysis to evaluate the performance of the method is shown, in comparison to VHF/UHF antenna measurements. The potential benefits of this novel technique rely on the small attenuation of PD signals in the GIS components in the HF range and sample rate reductions. Finally, a discussion on the potential applicability of present cluster and charge calculation techniques to the proposed PD GIS measurement using HFCT is presented. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

16 pages, 8334 KiB  
Article
Novel Simulation Technique of Electromagnetic Wave Propagation in the Ultra High Frequency Range within Power Transformers
by Takahiro Umemoto and Stefan Tenbohlen
Sensors 2018, 18(12), 4236; https://doi.org/10.3390/s18124236 - 3 Dec 2018
Cited by 14 | Viewed by 4465
Abstract
Diagnoses of power transformers by partial discharge (PD) measurement are effective to prevent dielectric failures of the apparatus. Ultra-high frequency (UHF) method has recently received attention due to its various advantages, such as the robustness against external noise and the capability of PD [...] Read more.
Diagnoses of power transformers by partial discharge (PD) measurement are effective to prevent dielectric failures of the apparatus. Ultra-high frequency (UHF) method has recently received attention due to its various advantages, such as the robustness against external noise and the capability of PD localization. However, electromagnetic (EM) waves radiated from PD tend to suffer attenuation before arriving at UHF sensors, because active part of the transformer disturbs the EM wave propagation. In some cases, that results in poor detection sensitivity. To understand propagation and attenuation characteristics of EM waves and to evaluate the detection sensitivity quantitatively, a computational approach to simulate the EM wave propagation is important. Although many previous researches have dealt with EM wave simulation for transformers, validations of those simulations by comparing with the experimental ones have seldom been reported. In this paper, cumulative energies, signal amplitudes and propagation times of EM waves were measured using a 630 kVA transformer. EM wave propagation was computed using the time-domain finite integration technique and the results were compared with the experimentally obtained ones. These simulation results showed good agreement with the experimental ones. The results can serve as guidelines to improve the efficiency of UHF PD detection and offer the possibility to achieve optimal placement of UHF sensors in power transformers. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

11 pages, 4158 KiB  
Article
Improving the Error of Time Differences of Arrival on Partial Discharges Measurement in Gas-Insulated Switchgear
by Jun Jiang, Kai Wang, Chaohai Zhang, Min Chen, Hong Zheng and Ricardo Albarracín
Sensors 2018, 18(11), 4078; https://doi.org/10.3390/s18114078 - 21 Nov 2018
Cited by 11 | Viewed by 5091
Abstract
Partial Discharge (PD) detection based on Ultra-High-Frequency (UHF) measurements in Gas-Insulated Switchgear (GIS) is often used for fault location based on extraction of Time Differences of Arrival (TDoA), and the core technique is to obtain the precise time difference of each UHF signal. [...] Read more.
Partial Discharge (PD) detection based on Ultra-High-Frequency (UHF) measurements in Gas-Insulated Switchgear (GIS) is often used for fault location based on extraction of Time Differences of Arrival (TDoA), and the core technique is to obtain the precise time difference of each UHF signal. Usually, TDoA extraction algorithms can be categorized as cross-correlation function method (CCF), minimum energy method (ME), and threshold value method (TV) are not qualified to analyze the time difference with high accuracy and efficiency, especially the complicated UHF PD signals in the field. In this paper, multiple tests were carried out based on the real GIS UHF signals. Three typical algorithms (CCF, ME, and TV) were used to extract and calculate the TDoA of UHF signals. Afterwards, depending on the disassembly of equipment, the accuracy and effective range of the algorithms are analyzed by means of error and variance. To minimize the error and the variance, an average method with the combination (CA) and portfolio of traditional algorithms is proposed and verified in different situations. The results demonstrate that the improved algorithm could increase the accuracy of time difference extraction, less than 4.0%. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

19 pages, 4999 KiB  
Article
An Efficient Algorithm for Partial Discharge Localization in High-Voltage Systems Using Received Signal Strength
by Umar F. Khan, Pavlos I. Lazaridis, Hamd Mohamed, Ricardo Albarracín, Zaharias D. Zaharis, Robert C. Atkinson, Christos Tachtatzis and Ian A. Glover
Sensors 2018, 18(11), 4000; https://doi.org/10.3390/s18114000 - 16 Nov 2018
Cited by 29 | Viewed by 4533
Abstract
The term partial discharge (PD) refers to a partial bridging of insulating material between electrodes that sustain an electric field in high-voltage (HV) systems. Long-term PD activity can lead to catastrophic failures of HV systems resulting in economic, energy and even human life [...] Read more.
The term partial discharge (PD) refers to a partial bridging of insulating material between electrodes that sustain an electric field in high-voltage (HV) systems. Long-term PD activity can lead to catastrophic failures of HV systems resulting in economic, energy and even human life losses. Such failures and losses can be avoided by continuously monitoring PD activity. Existing techniques used for PD localization including time of arrival (TOA) and time difference of arrival (TDOA), are complicated and expensive because they require time synchronization. In this paper, a novel received signal strength (RSS) based localization algorithm is proposed. The reason that RSS is favoured in this research is that it does not require clock synchronization and it only requires the energy of the received signal rather than the PD pulse itself. A comparison was made between RSS based algorithms including a proposed algorithm, the ratio and search and the least squares algorithm to locate a PD source for nine different positions. The performance of the algorithms was evaluated by using two field scenarios based on seven and eight receiving nodes, respectively. The mean localization error calculated for two-field-trial scenarios show, respectively, 1.80 m and 1.76 m for the proposed algorithm for all nine positions, which is the lowest of the three algorithms. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

13 pages, 5262 KiB  
Article
Design of Wideband GHz Electric Field Sensor Integrated with Optical Fiber Transmission Link for Electromagnetic Pulse Signal Measurement
by Guogang Zhang, Wenfan Li, Lu Qi, Jingcun Liu, Zhengxiang Song and Jianhua Wang
Sensors 2018, 18(9), 3167; https://doi.org/10.3390/s18093167 - 19 Sep 2018
Cited by 11 | Viewed by 6470
Abstract
The detection of high frequency overvoltage and partial discharge is of great significance in evaluating the insulation condition of high-voltage power equipment. A wideband GHz electric field (E-field) sensor for electromagnetic pulse (EMP) signal measurement was proposed in this paper. An optical fiber [...] Read more.
The detection of high frequency overvoltage and partial discharge is of great significance in evaluating the insulation condition of high-voltage power equipment. A wideband GHz electric field (E-field) sensor for electromagnetic pulse (EMP) signal measurement was proposed in this paper. An optical fiber transmission link was adopted in the design in order to implement high-voltage isolation and reduce electromagnetic interference during transmission. The designed sensor was mainly made up of a differential electric field (D-dot) antenna, transmitter, and receiver. The D-dot antenna was designed to detect high frequency E-field strength and generate a corresponding voltage signal, which was converted into an optical signal by the transmitter. The optical signal could be transmitted a large distance through an optical fiber without electromagnetic interference and changed back to a voltage signal again by a receiver. The design process of the sensor was introduced in detail, and experiments were performed using a gigahertz transverse electromagnetic (GTEM) cell and an EMP simulator to verify it. The results indicated that the designed sensor had a good performance besides an expectable delay due to the optional amplifier. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

17 pages, 5236 KiB  
Article
Imaging Time Series for the Classification of EMI Discharge Sources
by Imene Mitiche, Gordon Morison, Alan Nesbitt, Michael Hughes-Narborough, Brian G. Stewart and Philip Boreham
Sensors 2018, 18(9), 3098; https://doi.org/10.3390/s18093098 - 14 Sep 2018
Cited by 14 | Viewed by 4641
Abstract
In this work, we aim to classify a wider range of Electromagnetic Interference (EMI) discharge sources collected from new power plant sites across multiple assets. This engenders a more complex and challenging classification task. The study involves an investigation and development of new [...] Read more.
In this work, we aim to classify a wider range of Electromagnetic Interference (EMI) discharge sources collected from new power plant sites across multiple assets. This engenders a more complex and challenging classification task. The study involves an investigation and development of new and improved feature extraction and data dimension reduction algorithms based on image processing techniques. The approach is to exploit the Gramian Angular Field technique to map the measured EMI time signals to an image, from which the significant information is extracted while removing redundancy. The image of each discharge type contains a unique fingerprint. Two feature reduction methods called the Local Binary Pattern (LBP) and the Local Phase Quantisation (LPQ) are then used within the mapped images. This provides feature vectors that can be implemented into a Random Forest (RF) classifier. The performance of a previous and the two new proposed methods, on the new database set, is compared in terms of classification accuracy, precision, recall, and F-measure. Results show that the new methods have a higher performance than the previous one, where LBP features achieve the best outcome. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

15 pages, 7211 KiB  
Article
Field Applications of Ultra High Frequency Techniques for Defect Detection in GIS
by Jun Xiong, Yuan Wang, Guo-Ming Ma, Qiang Zhang and Shu-Sheng Zheng
Sensors 2018, 18(8), 2425; https://doi.org/10.3390/s18082425 - 26 Jul 2018
Cited by 10 | Viewed by 4442
Abstract
The reliable and stable operation of power apparatus is important for the development of GIS. It is important to utilize condition monitoring technologies and anticipate possible failures in advance. Many papers have been published about the partial discharge detection with UHF or X-ray [...] Read more.
The reliable and stable operation of power apparatus is important for the development of GIS. It is important to utilize condition monitoring technologies and anticipate possible failures in advance. Many papers have been published about the partial discharge detection with UHF or X-ray in laboratory, but seldom in field application. Thus, many engineers at project sites are not familiar with the current professional diagnosis techniques. Recently, during the GIS routine data analysis obtained by partial discharge online monitoring system, it was found that the UHF monitoring signals’ developing trend of the 220 kV GIS No. 2 high-voltage side of transformer in phase C at an actual station was abnormal and needed further detection. In order to precisely investigate the problem and then guide the operation and maintenance activities, a series of professional diagnoses were conducted. Three new types of partial discharge detection and positioning methods were applied for accuracy, including UHF partial discharge detection based on multi-stage amplified signal demodulation and multiple weighted averages processing; the partial discharge detection based on the signal radiation hole of insulation disk at the ground connection; and the positioning method based on UHF-SHF. After a series of troubleshooting works, the partial discharge defects have been diagnosed, and the case can be referred in the field monitoring of GIS. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

19 pages, 6051 KiB  
Article
Partial Discharge Spectral Characterization in HF, VHF and UHF Bands Using Particle Swarm Optimization
by Guillermo Robles, José Manuel Fresno, Juan Manuel Martínez-Tarifa, Jorge Alfredo Ardila-Rey and Emilio Parrado-Hernández
Sensors 2018, 18(3), 746; https://doi.org/10.3390/s18030746 - 1 Mar 2018
Cited by 22 | Viewed by 5426
Abstract
The measurement of partial discharge (PD) signals in the radio frequency (RF) range has gained popularity among utilities and specialized monitoring companies in recent years. Unfortunately, in most of the occasions the data are hidden by noise and coupled interferences that hinder their [...] Read more.
The measurement of partial discharge (PD) signals in the radio frequency (RF) range has gained popularity among utilities and specialized monitoring companies in recent years. Unfortunately, in most of the occasions the data are hidden by noise and coupled interferences that hinder their interpretation and renders them useless especially in acquisition systems in the ultra high frequency (UHF) band where the signals of interest are weak. This paper is focused on a method that uses a selective spectral signal characterization to feature each signal, type of partial discharge or interferences/noise, with the power contained in the most representative frequency bands. The technique can be considered as a dimensionality reduction problem where all the energy information contained in the frequency components is condensed in a reduced number of UHF or high frequency (HF) and very high frequency (VHF) bands. In general, dimensionality reduction methods make the interpretation of results a difficult task because the inherent physical nature of the signal is lost in the process. The proposed selective spectral characterization is a preprocessing tool that facilitates further main processing. The starting point is a clustering of signals that could form the core of a PD monitoring system. Therefore, the dimensionality reduction technique should discover the best frequency bands to enhance the affinity between signals in the same cluster and the differences between signals in different clusters. This is done maximizing the minimum Mahalanobis distance between clusters using particle swarm optimization (PSO). The tool is tested with three sets of experimental signals to demonstrate its capabilities in separating noise and PDs with low signal-to-noise ratio and separating different types of partial discharges measured in the UHF and HF/VHF bands. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

20 pages, 15730 KiB  
Article
Diagnosis of Insulation Condition of MV Switchgears by Application of Different Partial Discharge Measuring Methods and Sensors
by Fernando Álvarez Gómez, Ricardo Albarracín-Sánchez, Fernando Garnacho Vecino and Ricardo Granizo Arrabé
Sensors 2018, 18(3), 720; https://doi.org/10.3390/s18030720 - 28 Feb 2018
Cited by 25 | Viewed by 8336
Abstract
Partial discharges (PD) measurement provides valuable information for the condition assessment of the insulation status of high-voltage (HV) electrical installations. During the last three decades, several PD sensors and measuring techniques have been developed to perform accurate diagnostics when PD measurements are carried [...] Read more.
Partial discharges (PD) measurement provides valuable information for the condition assessment of the insulation status of high-voltage (HV) electrical installations. During the last three decades, several PD sensors and measuring techniques have been developed to perform accurate diagnostics when PD measurements are carried out on-site and on-line. For utilities, the most attractive characteristics of on-line measurements are that once the sensors are installed in the grid, the electrical service is uninterrupted and that electrical systems are tested in real operating conditions. In medium-voltage (MV) and HV installations, one of the critical points where an insulation defect can occur is inside metal-clad switchgears (including the cable terminals connected to them). Thus, this kind of equipment is increasingly being monitored to carry out proper maintenance based on their condition. This paper presents a study concerning the application of different electromagnetic measuring techniques (compliant with IEC 62478 and IEC 60270 standards), together with the use of suitable sensors, which enable the evaluation of the insulation condition mainly in MV switchgears. The main scope is to give a general overview about appropriate types of electromagnetic measuring methods and sensors to be applied, while considering the level of detail and accuracy in the diagnosis and the particular fail-save requirements of the electrical installations where the switchgears are located. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

18 pages, 18978 KiB  
Article
Partial Discharge Monitoring on Metal-Enclosed Switchgear with Distributed Non-Contact Sensors
by Chongxing Zhang, Ming Dong, Ming Ren, Wenguang Huang, Jierui Zhou, Xuze Gao and Ricardo Albarracín
Sensors 2018, 18(2), 551; https://doi.org/10.3390/s18020551 - 11 Feb 2018
Cited by 31 | Viewed by 11632
Abstract
Metal-enclosed switchgear, which are widely used in the distribution of electrical energy, play an important role in power distribution networks. Their safe operation is directly related to the reliability of power system as well as the power quality on the consumer side. Partial [...] Read more.
Metal-enclosed switchgear, which are widely used in the distribution of electrical energy, play an important role in power distribution networks. Their safe operation is directly related to the reliability of power system as well as the power quality on the consumer side. Partial discharge detection is an effective way to identify potential faults and can be utilized for insulation diagnosis of metal-enclosed switchgear. The transient earth voltage method, an effective non-intrusive method, has substantial engineering application value for estimating the insulation condition of switchgear. However, the practical application effectiveness of TEV detection is not satisfactory because of the lack of a TEV detection application method, i.e., a method with sufficient technical cognition and analysis. This paper proposes an innovative online PD detection system and a corresponding application strategy based on an intelligent feedback distributed TEV wireless sensor network, consisting of sensing, communication, and diagnosis layers. In the proposed system, the TEV signal or status data are wirelessly transmitted to the terminal following low-energy signal preprocessing and acquisition by TEV sensors. Then, a central server analyzes the correlation of the uploaded data and gives a fault warning level according to the quantity, trend, parallel analysis, and phase resolved partial discharge pattern recognition. In this way, a TEV detection system and strategy with distributed acquisition, unitized fault warning, and centralized diagnosis is realized. The proposed system has positive significance for reducing the fault rate of medium voltage switchgear and improving its operation and maintenance level. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

14 pages, 1654 KiB  
Article
Classification of Partial Discharge Signals by Combining Adaptive Local Iterative Filtering and Entropy Features
by Imene Mitiche, Gordon Morison, Alan Nesbitt, Michael Hughes-Narborough, Brian G. Stewart and Philip Boreham
Sensors 2018, 18(2), 406; https://doi.org/10.3390/s18020406 - 31 Jan 2018
Cited by 31 | Viewed by 5581
Abstract
Electromagnetic Interference (EMI) is a technique for capturing Partial Discharge (PD) signals in High-Voltage (HV) power plant apparatus. EMI signals can be non-stationary which makes their analysis difficult, particularly for pattern recognition applications. This paper elaborates upon a previously developed software condition-monitoring model [...] Read more.
Electromagnetic Interference (EMI) is a technique for capturing Partial Discharge (PD) signals in High-Voltage (HV) power plant apparatus. EMI signals can be non-stationary which makes their analysis difficult, particularly for pattern recognition applications. This paper elaborates upon a previously developed software condition-monitoring model for improved EMI events classification based on time-frequency signal decomposition and entropy features. The idea of the proposed method is to map multiple discharge source signals captured by EMI and labelled by experts, including PD, from the time domain to a feature space, which aids in the interpretation of subsequent fault information. Here, instead of using only one permutation entropy measure, a more robust measure, called Dispersion Entropy (DE), is added to the feature vector. Multi-Class Support Vector Machine (MCSVM) methods are utilized for classification of the different discharge sources. Results show an improved classification accuracy compared to previously proposed methods. This yields to a successful development of an expert’s knowledge-based intelligent system. Since this method is demonstrated to be successful with real field data, it brings the benefit of possible real-world application for EMI condition monitoring. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

1809 KiB  
Article
Survey on the Performance of Source Localization Algorithms
by José Manuel Fresno, Guillermo Robles, Juan Manuel Martínez-Tarifa and Brian G. Stewart
Sensors 2017, 17(11), 2666; https://doi.org/10.3390/s17112666 - 18 Nov 2017
Cited by 38 | Viewed by 5841
Abstract
The localization of emitters using an array of sensors or antennas is a prevalent issue approached in several applications. There exist different techniques for source localization, which can be classified into multilateration, received signal strength (RSS) and proximity methods. The performance of multilateration [...] Read more.
The localization of emitters using an array of sensors or antennas is a prevalent issue approached in several applications. There exist different techniques for source localization, which can be classified into multilateration, received signal strength (RSS) and proximity methods. The performance of multilateration techniques relies on measured time variables: the time of flight (ToF) of the emission from the emitter to the sensor, the time differences of arrival (TDoA) of the emission between sensors and the pseudo-time of flight (pToF) of the emission to the sensors. The multilateration algorithms presented and compared in this paper can be classified as iterative and non-iterative methods. Both standard least squares (SLS) and hyperbolic least squares (HLS) are iterative and based on the Newton–Raphson technique to solve the non-linear equation system. The metaheuristic technique particle swarm optimization (PSO) used for source localisation is also studied. This optimization technique estimates the source position as the optimum of an objective function based on HLS and is also iterative in nature. Three non-iterative algorithms, namely the hyperbolic positioning algorithms (HPA), the maximum likelihood estimator (MLE) and Bancroft algorithm, are also presented. A non-iterative combined algorithm, MLE-HLS, based on MLE and HLS, is further proposed in this paper. The performance of all algorithms is analysed and compared in terms of accuracy in the localization of the position of the emitter and in terms of computational time. The analysis is also undertaken with three different sensor layouts since the positions of the sensors affect the localization; several source positions are also evaluated to make the comparison more robust. The analysis is carried out using theoretical time differences, as well as including errors due to the effect of digital sampling of the time variables. It is shown that the most balanced algorithm, yielding better results than the other algorithms in terms of accuracy and short computational time, is the combined MLE-HLS algorithm. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

1736 KiB  
Article
Detection of Partial Discharge Sources Using UHF Sensors and Blind Signal Separation
by Carlos Boya, Guillermo Robles, Emilio Parrado-Hernández and Marta Ruiz-Llata
Sensors 2017, 17(11), 2625; https://doi.org/10.3390/s17112625 - 15 Nov 2017
Cited by 18 | Viewed by 5953
Abstract
The measurement of the emitted electromagnetic energy in the UHF region of the spectrum allows the detection of partial discharges and, thus, the on-line monitoring of the condition of the insulation of electrical equipment. Unfortunately, determining the affected asset is difficult when there [...] Read more.
The measurement of the emitted electromagnetic energy in the UHF region of the spectrum allows the detection of partial discharges and, thus, the on-line monitoring of the condition of the insulation of electrical equipment. Unfortunately, determining the affected asset is difficult when there are several simultaneous insulation defects. This paper proposes the use of an independent component analysis (ICA) algorithm to separate the signals coming from different partial discharge (PD) sources. The performance of the algorithm has been tested using UHF signals generated by test objects. The results are validated by two automatic classification techniques: support vector machines and similarity with class mean. Both methods corroborate the suitability of the algorithm to separate the signals emitted by each PD source even when they are generated by the same type of insulation defect. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

Review

Jump to: Research

23 pages, 3005 KiB  
Review
Application of UHF Sensors in Power System Equipment for Partial Discharge Detection: A Review
by Hua Chai, B.T. Phung and Steve Mitchell
Sensors 2019, 19(5), 1029; https://doi.org/10.3390/s19051029 - 28 Feb 2019
Cited by 99 | Viewed by 13326
Abstract
Condition monitoring of an operating apparatus is essential for lifespan assessment and maintenance planning in a power system. Electrical insulation is a critical aspect to be monitored, since it is susceptible to failure under high electrical stress. To avoid unexpected breakdowns, the level [...] Read more.
Condition monitoring of an operating apparatus is essential for lifespan assessment and maintenance planning in a power system. Electrical insulation is a critical aspect to be monitored, since it is susceptible to failure under high electrical stress. To avoid unexpected breakdowns, the level of partial discharge (PD) activity should be continuously monitored because PD occurrence can accelerate the aging process of insulation in high voltage equipment and result in catastrophic failure if the associated defects are not treated at an early stage. For on-site PD detection, the ultra-high frequency (UHF) method was employed in the field and showed its effectiveness as a detection technique. The main advantage of the UHF method is its immunity to external electromagnetic interference with a high signal-to-noise ratio, which is necessary for on-site monitoring. Considering the detection process, sensors play a critical role in capturing signals from PD sources and transmitting them onto the measurement system. In this paper, UHF sensors applied in PD detection were comprehensively reviewed. In particular, for power transformers, the effects of the physical structure on UHF signals and practical applications of UHF sensors including PD localization techniques were discussed. The aim of this review was to present state-of-the-art UHF sensors in PD detection and facilitate future improvements in the UHF method. Full article
(This article belongs to the Special Issue UHF and RF Sensor Technology for Partial Discharge Detection)
Show Figures

Figure 1

Back to TopTop