Next Article in Journal
Spectral-Spatial Feature Extraction of Hyperspectral Images Based on Propagation Filter
Next Article in Special Issue
Huber’s Non-Linearity for GNSS Interference Mitigation
Previous Article in Journal
On the Coverage of Bus-Based Mobile Sensing
Previous Article in Special Issue
GNSS Code Multipath Mitigation by Cascading Measurement Monitoring Techniques
Article Menu
Issue 6 (June) cover image

Export Article

Open AccessArticle
Sensors 2018, 18(6), 1977; https://doi.org/10.3390/s18061977

A New Method of High-Precision Positioning for an Indoor Pseudolite without Using the Known Point Initialization

1,2,3
,
1,2,3,* , 1,2,3,* , 4
,
5
,
1,2,3
and
1
1
School of Geodesy and Geomatics, Wuhan University, Wuhan 430079, China
2
Key Laboratory of Precise Engineering and Industry Surveying of National Administration of Surveying, Mapping and Geoinformation, Wuhan University, Wuhan 430079, China
3
Research Center for High Accuracy Location Awareness, Wuhan University 430079, China
4
College of Geology Engineering and Geomatics, Chang’an University, Xi’an 710054, China
5
School of Surveying and Spatial Information Systems, The University of New South Wales, Sydney 2052, Australia
*
Authors to whom correspondence should be addressed.
Received: 15 May 2018 / Revised: 8 June 2018 / Accepted: 19 June 2018 / Published: 20 June 2018
(This article belongs to the Special Issue GNSS and Fusion with Other Sensors)
Full-Text   |   PDF [4857 KB, uploaded 20 June 2018]   |  

Abstract

Due to the great influence of multipath effect, noise, clock and error on pseudorange, the carrier phase double difference equation is widely used in high-precision indoor pseudolite positioning. The initial position is determined mostly by the known point initialization (KPI) method, and then the ambiguities can be fixed with the LAMBDA method. In this paper, a new method without using the KPI to achieve high-precision indoor pseudolite positioning is proposed. The initial coordinates can be quickly obtained to meet the accuracy requirement of the indoor LAMBDA method. The detailed processes of the method follows: Aiming at the low-cost single-frequency pseudolite system, the static differential pseudolite system (DPL) method is used to obtain the low-accuracy positioning coordinates of the rover station quickly. Then, the ambiguity function method (AFM) is used to search for the coordinates in the corresponding epoch. The real coordinates obtained by AFM can meet the initial accuracy requirement of the LAMBDA method, so that the double difference carrier phase ambiguities can be correctly fixed. Following the above steps, high-precision indoor pseudolite positioning can be realized. Several experiments, including static and dynamic tests, are conducted to verify the feasibility of the new method. According to the results of the experiments, the initial coordinates with the accuracy of decimeter level through the DPL can be obtained. For the AFM part, both a one-meter search scope and two-centimeter or four-centimeter search steps are used to ensure the precision at the centimeter level and high search efficiency. After dealing with the problem of multiple peaks caused by the ambiguity cosine function, the coordinate information of the maximum ambiguity function value (AFV) is taken as the initial value of the LAMBDA, and the ambiguities can be fixed quickly. The new method provides accuracies at the centimeter level for dynamic experiments and at the millimeter level for static ones. View Full-Text
Keywords: differential pseudolite system; pseudolite differential positioning; ambiguity function method; LAMBDA method differential pseudolite system; pseudolite differential positioning; ambiguity function method; LAMBDA method
Figures

Figure 1

This is an open access article distributed under the Creative Commons Attribution License which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited (CC BY 4.0).
SciFeed

Share & Cite This Article

MDPI and ACS Style

Zhao, Y.; Zhang, P.; Guo, J.; Li, X.; Wang, J.; Yang, F.; Wang, X. A New Method of High-Precision Positioning for an Indoor Pseudolite without Using the Known Point Initialization. Sensors 2018, 18, 1977.

Show more citation formats Show less citations formats

Note that from the first issue of 2016, MDPI journals use article numbers instead of page numbers. See further details here.

Related Articles

Article Metrics

Article Access Statistics

1

Comments

[Return to top]
Sensors EISSN 1424-8220 Published by MDPI AG, Basel, Switzerland RSS E-Mail Table of Contents Alert
Back to Top