Topic Editors

Institut de Minéralogie, de Physique des Matériaux et de Cosmochimie (IMPMC), Sorbonne Université, CNRS-UMR 7590, 4 Place Jussieu, 75252 Paris, France
Institute of Materials for Energy and Environment, School of Materials Science and Engineering, Qingdao University, Qingdao, China

Advanced Nanomaterials for Lithium-Ion Batteries

Abstract submission deadline
closed (31 March 2024)
Manuscript submission deadline
closed (31 May 2024)
Viewed by
32065

Topic Information

Dear Colleagues,

The key fundamental discovery underlying lithium-ion batteries (LIBs) is the understanding and application of the insertion of ions between layers of graphite, metal sulfides and oxides. Thirty years later, the exceptional development of lithium-ion battery technology has been rewarded with the 2019 Nobel Prize in Chemistry. As the research effort continues, this Special Issue is devoted to Advanced Nanomaterials for LIBs. Recent developments outline the chemistries of lithium-ion batteries, including cathode and anode materials, organic electrodes, solid-state electrolytes, solid polymers, and solvent-in-salt electrolytes and other chemistries. These advances cover novel synthetic methods, crystal chemistry, structure and physico-chemical properties, redox reactions, and electrochemical performance. We invite contributions on topics that include original research data, review articles, communications, and short notes that focus on new (experimental or theoretical) advances, challenges, and perspectives of nanomaterials for LIBs concerning their preparation, characterization, and application.

Prof. Dr. Christian Julien
Prof. Dr. Binghui Xu
Topic Editors

Keywords

  • lithium-ion batteries
  • nanomaterials
  • cathodes
  • anodes
  • solid-state electrolytes
  • redox reactions
  • electrochemical performance
  • interfaces

Participating Journals

Journal Name Impact Factor CiteScore Launched Year First Decision (median) APC
Batteries
batteries
4.6 4.0 2015 22 Days CHF 2700
Energies
energies
3.0 6.2 2008 17.5 Days CHF 2600
Materials
materials
3.1 5.8 2008 15.5 Days CHF 2600
Nanomaterials
nanomaterials
4.4 8.5 2010 13.8 Days CHF 2900
Nanoenergy Advances
nanoenergyadv
- - 2021 25 Days CHF 1000

Preprints.org is a multidiscipline platform providing preprint service that is dedicated to sharing your research from the start and empowering your research journey.

MDPI Topics is cooperating with Preprints.org and has built a direct connection between MDPI journals and Preprints.org. Authors are encouraged to enjoy the benefits by posting a preprint at Preprints.org prior to publication:

  1. Immediately share your ideas ahead of publication and establish your research priority;
  2. Protect your idea from being stolen with this time-stamped preprint article;
  3. Enhance the exposure and impact of your research;
  4. Receive feedback from your peers in advance;
  5. Have it indexed in Web of Science (Preprint Citation Index), Google Scholar, Crossref, SHARE, PrePubMed, Scilit and Europe PMC.

Published Papers (17 papers)

Order results
Result details
Journals
Select all
Export citation of selected articles as:
9 pages, 1811 KiB  
Article
Green Phytic Acid-Assisted Synthesis of LiMn1-xFexPO4/C Cathodes for High-Performance Lithium-Ion Batteries
by Yueying Li, Chenlu Hu, Zhidong Hou, Chunguang Wei and Jian-Gan Wang
Nanomaterials 2024, 14(16), 1360; https://doi.org/10.3390/nano14161360 - 19 Aug 2024
Viewed by 1203
Abstract
As a promising cathode material, olivine-structured LiMnPO4 holds enormous potential for lithium-ion batteries. Herein, we demonstrate a green biomass-derived phytic-acid-assisted method to synthesize a series of LiMn1−xFexPO4/C composites. The effect of Fe doping on the crystal [...] Read more.
As a promising cathode material, olivine-structured LiMnPO4 holds enormous potential for lithium-ion batteries. Herein, we demonstrate a green biomass-derived phytic-acid-assisted method to synthesize a series of LiMn1−xFexPO4/C composites. The effect of Fe doping on the crystal structure and morphology of LiMnPO4 particles is investigated. It is revealed that the optimal Fe doping amount of x = 0.2 enables a substantial enhancement of interfacial charge transfer ability and Li+ ion diffusion kinetics. Consequently, a large reversible capacity output of 146 mAh g−1 at 0.05 C and a high rate capacity of 77 mAh g−1 at 2 C were acquired by the as-optimized LiMn0.8Fe0.2PO4/C cathode. Moreover, the LiMn0.8Fe0.2PO4/C delivered a specific capacity of 68 mAh g−1 at 2 C after 500 cycles, with a capacity retention of 88.4%. This work will unveil a green synthesis route for advancing phosphate cathode materials toward practical implementation. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Graphical abstract

17 pages, 8971 KiB  
Article
Functionalized γ-Boehmite Covalent Grafting Modified Polyethylene for Lithium-Ion Battery Separator
by Yuanxin Man, Hui Nan, Jianzhe Ma, Zhike Li, Jingyuan Zhou, Xianlan Wang, Heqi Li, Caihong Xue and Yongchun Yang
Materials 2024, 17(9), 2162; https://doi.org/10.3390/ma17092162 - 6 May 2024
Viewed by 1451
Abstract
In the field of lithium-ion batteries, the challenges posed by the low melting point and inadequate wettability of conventional polyolefin separators have increased the focus on ceramic-coated separators. This study introduces a highly efficient and stable boehmite/polydopamine/polyethylene (AlOOH-PDA-PE) separator. It is crafted by [...] Read more.
In the field of lithium-ion batteries, the challenges posed by the low melting point and inadequate wettability of conventional polyolefin separators have increased the focus on ceramic-coated separators. This study introduces a highly efficient and stable boehmite/polydopamine/polyethylene (AlOOH-PDA-PE) separator. It is crafted by covalently attaching functionalized nanosized boehmite (γ-AlOOH) whiskers onto polyethylene (PE) surfaces. The presence of a covalent bond increases the stability at the interface, while amino groups on the surface of the separator enhance the infiltration of the electrolyte and facilitate the diffusion of lithium ions. The PE-PDA-AlOOH separator, when used in lithium-ion batteries, achieves a discharge capacity of 126 mAh g−1 at 5 C and retains 97.1% capacity after 400 cycles, indicating superior cycling stability due to its covalently bonded ceramic surface. Thus, covalent interface modification is a promising strategy to prevent delamination of ceramic coatings in separators. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

19 pages, 11634 KiB  
Article
A Study on the Microstructure Regulation Effect of Niobium Doping on LiNi0.88Co0.05Mn0.07O2 and the Electrochemical Performance of the Composite Material under High Voltage
by Xinrui Xu, Junjie Liu, Bo Wang, Jiaqi Wang, Yunchang Wang, Weisong Meng and Feipeng Cai
Materials 2024, 17(9), 2127; https://doi.org/10.3390/ma17092127 - 30 Apr 2024
Cited by 1 | Viewed by 919
Abstract
High-nickel ternary materials are currently the most promising lithium battery cathode materials due to their development and application potential. Nevertheless, these materials encounter challenges like cation mixing, lattice oxygen loss, interfacial reactions, and microcracks. These issues are exacerbated at high voltages, compromising their [...] Read more.
High-nickel ternary materials are currently the most promising lithium battery cathode materials due to their development and application potential. Nevertheless, these materials encounter challenges like cation mixing, lattice oxygen loss, interfacial reactions, and microcracks. These issues are exacerbated at high voltages, compromising their cyclic stability and safety. In this study, we successfully prepared Nb5+-doped high-nickel ternary cathode materials via a high-temperature solid-phase method. We investigated the impact of Nb5+ doping on the microstructure and electrochemical properties of LiNi0.88Co0.05Mn0.07O2 ternary cathode materials by varying the amount of Nb2O5 added. The experimental results suggest that Nb5+ doping does not alter the crystal structure but modifies the particle morphology, yielding radially distributed, elongated, rod-like structures. This morphology effectively mitigates the anisotropic volume changes during cycling, thereby bolstering the material’s cyclic stability. The material exhibits a discharge capacity of 224.4 mAh g−1 at 0.1C and 200.3 mAh g−1 at 1C, within a voltage range of 2.7 V–4.5 V. Following 100 cycles at 1C, the capacity retention rate maintains a high level of 92.9%, highlighting the material’s remarkable capacity retention and cyclic stability under high-voltage conditions. The enhancement of cyclic stability is primarily due to the synergistic effects caused by Nb5+ doping. Nb5+ modifies the particle morphology, thereby mitigating the formation of microcracks. The formation of high-energy Nb-O bonds prevents oxygen precipitation at high voltages, minimizes the irreversibility of the H2–H3 phase transition, and thereby enhances the stability of the composite material at high voltages. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

11 pages, 2465 KiB  
Article
Surface-Pore-Modified N-Doped Amorphous Carbon Nanospheres Tailored with Toluene as Anode Materials for Lithium-Ion Batteries
by Shiran Shan, Chunze Yuan, Guangsu Tan, Chao Xu, Lin Li, Guoqi Li, Jihao Zhang and Tsu-Chien Weng
Nanomaterials 2024, 14(9), 772; https://doi.org/10.3390/nano14090772 - 28 Apr 2024
Viewed by 1181
Abstract
The surface modification of amorphous carbon nanospheres (ACNs) through templates has attracted great attention due to its great success in improving the electrochemical properties of lithium storage materials. Herein, a safe methodology with toluene as a soft template is employed to tailor the [...] Read more.
The surface modification of amorphous carbon nanospheres (ACNs) through templates has attracted great attention due to its great success in improving the electrochemical properties of lithium storage materials. Herein, a safe methodology with toluene as a soft template is employed to tailor the nanostructure, resulting in ACNs with tunable surface pores. Extensive characterizations through transmission electron microscopy (TEM), scanning electron microscopy (SEM), Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption/desorption isotherms elucidate the impact of surface pore modifications on the external structure, morphology, and surface area. Electrochemical assessments reveal the enhanced performance of the surface-pore-modified carbon nanospheres, particularly ACNs-100 synthesized with the addition of 100 μL toluene, in terms of the initial discharge capacity, rate performance, and cycling stability. The interesting phenomenon of persistent capacity increase is ascribed to lithium ion movement within the graphite-like interlayer, resulting in ACNs-100 experiencing a capacity upswing from an initial 320 mAh g−1 to a zenith of 655 mAh g−1 over a thousand cycles at a rate of 2 C. The findings in this study highlight the pivotal role of tailored nanostructure engineering in optimizing energy storage materials. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

13 pages, 4882 KiB  
Article
Engineering Nano-Sized Silicon Anodes with Conductive Networks toward a High Average Coulombic Efficiency of 90.2% via Plasma-Assisted Milling
by Yezhan Zuo, Xingyu Xiong, Zhenzhong Yang, Yihui Sang, Haolin Zhang, Fanbo Meng and Renzong Hu
Nanomaterials 2024, 14(8), 660; https://doi.org/10.3390/nano14080660 - 10 Apr 2024
Viewed by 1631
Abstract
Si-based anode is considered one of the ideal anodes for high energy density lithium-ion batteries due to its high theoretical capacity of 4200 mAh g−1. To accelerate the commercial progress of Si material, the multi-issue of extreme volume expansion and low [...] Read more.
Si-based anode is considered one of the ideal anodes for high energy density lithium-ion batteries due to its high theoretical capacity of 4200 mAh g−1. To accelerate the commercial progress of Si material, the multi-issue of extreme volume expansion and low intrinsic electronic conductivity needs to be settled. Herein, a series of nano-sized Si particles with conductive networks are synthesized via the dielectric barrier discharge plasma (DBDP) assisted milling. The p-milling method can effectively refine the particle sizes of pristine Si without destroying its crystal structure, resulting in large Brunauer–Emmett–Teller (BET) values with more active sites for Li+ ions. Due to their unique structure and flexibility, CNTs can be uniformly distributed among the Si particles and the prepared Si electrodes exhibit better structural stability during the continuous lithiation/de-lithiation process. Moreover, the CNT network accelerates the transport of ions and electrons in the Si particles. As a result, the nano-sized Si anodes with CNTs conductive network can deliver an extremely high average initial Coulombic efficiency (ICE) reach of 90.2% with enhanced cyclic property and rate capability. The C-PMSi-50:1 anode presents 615 mAh g−1 after 100 cycles and 979 mAh g−1 under the current density of 5 A g−1. Moreover, the manufactured Si||LiNi0.8Co0.1Mn0.1O2 pouch cell maintains a high ICE of >85%. This work may supply a new insight for designing the nano-sized Si and further promoting its commercial applications. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Graphical abstract

15 pages, 19056 KiB  
Article
Reutilization of Silicon-Cutting Waste via Constructing Multilayer Si@SiO2@C Composites as Anode Materials for Li-Ion Batteries
by Yi Sun, Jingyi Wu, Xingjie Chen and Chunyan Lai
Nanomaterials 2024, 14(7), 625; https://doi.org/10.3390/nano14070625 - 2 Apr 2024
Viewed by 1312
Abstract
The rapid development of the photovoltaic industry has also brought some economic losses and environmental problems due to the waste generated during silicon ingot cutting. This study introduces an effective and facile method to reutilize silicon-cutting waste by constructing a multilayer Si@SiO2 [...] Read more.
The rapid development of the photovoltaic industry has also brought some economic losses and environmental problems due to the waste generated during silicon ingot cutting. This study introduces an effective and facile method to reutilize silicon-cutting waste by constructing a multilayer Si@SiO2@C composite for Li-ion batteries via two-step annealing. The double-layer structure of the resultant composite alleviates the severe volume changes of silicon effectively, and the surrounding slightly graphitic carbon, known for its high conductivity and mechanical strength, tightly envelops the silicon nanoflakes, facilitates ion and electron transport and maintains electrode structural integrity throughout repeated charge/discharge cycles. With an optimization of the carbon content, the initial coulombic efficiency (ICE) was improved from 53% to 84%. The refined Si@SiO2@C anode exhibits outstanding cycling stability (711.4 mAh g−1 after 500 cycles) and rate performance (973.5 mAh g−1 at 2 C). This research presents a direct and cost-efficient strategy for transforming photovoltaic silicon-cutting waste into high-energy-density lithium-ion battery (LIB) anode materials. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

15 pages, 12522 KiB  
Article
Silicon–Nanodiamond-Based Anode for a Lithium-Ion Battery
by Cheng-Ying Jhan, Shi-Hong Sung and Yonhua Tzeng
Nanomaterials 2024, 14(1), 43; https://doi.org/10.3390/nano14010043 - 22 Dec 2023
Cited by 3 | Viewed by 1668
Abstract
Maintaining the physical integrity of a silicon-based anode, which suffers from damage caused by severe volume changes during cycling, is a top priority in its practical applications. The performance of silicon-flake-based anodes has been significantly improved by mixing nanodiamond powders with silicon flakes [...] Read more.
Maintaining the physical integrity of a silicon-based anode, which suffers from damage caused by severe volume changes during cycling, is a top priority in its practical applications. The performance of silicon-flake-based anodes has been significantly improved by mixing nanodiamond powders with silicon flakes for the fabrication of anodes for lithium-ion batteries (LIBs). Nanodiamonds adhere to the surfaces of silicon flakes and are distributed in the binder between flakes. A consistent and robust solid electrolyte interphase (SEI) is promoted by the aid of abundant reactive surface-linked functional groups and exposed dangling bonds of nanodiamonds, leading to enhanced physical integrity of the silicon flakes and the anode. The battery’s high-rate discharge capabilities and cycle life are thus improved. SEM, Raman spectroscopy, and XRD were applied to examine the structure and morphology of the anode. Electrochemical performance was evaluated to demonstrate a capacity retention of nearly 75% after 200 cycles, with the final specific capacity exceeding 1000 mAh/g at a test current of 4 mA/cm2. This is attributed to the improved stability of the solid electrolyte interphase (SEI) structure that was achieved by integrating nanodiamonds with silicon flakes in the anode, leading to enhanced cycling stability and rapid charge-discharge performance. The results from this study present an effective strategy of achieving high-cycling-performance by adding nanodiamonds to silicon-flake-based anodes. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

10 pages, 10928 KiB  
Communication
Enhancing the Stability and Initial Coulombic Efficiency of Silicon Anodes through Coating with Glassy ZIF-4
by In-Hwan Lee, Yongsheng Jin, Hyeon-Sik Jang and Dongmok Whang
Nanomaterials 2024, 14(1), 18; https://doi.org/10.3390/nano14010018 - 20 Dec 2023
Cited by 1 | Viewed by 1314
Abstract
The high capacity of electrodes allows for a lower mass of electrodes, which is essential for increasing the energy density of the batteries. According to this, silicon is a promising anode candidate for Li-ion batteries due to its high theoretical capacity. However, its [...] Read more.
The high capacity of electrodes allows for a lower mass of electrodes, which is essential for increasing the energy density of the batteries. According to this, silicon is a promising anode candidate for Li-ion batteries due to its high theoretical capacity. However, its practical application is hampered by the significant volume expansion of silicon during battery operation, resulting in pulverization and contact loss. In this study, we developed a stable Li-ion anode that not only solves the problem of the short lifetime of silicon but also preserves the initial efficiency by using silicon nanoparticles covered with glassy ZIF-4 (SZ-4). SZ-4 suppresses silicon pulverization, contact loss, etc. because the glassy ZIF-4 wrapped around the silicon nanoparticles prevents additional SEI formation outside the silicon surface due to the electrically insulating characteristics of glassy ZIF-4. The SZ-4 realized by a simple heat treatment method showed 74% capacity retention after 100 cycles and a high initial efficiency of 78.7%. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

13 pages, 6866 KiB  
Article
The Effect of Heat Treatment after Hydrothermal Reaction on the Lithium Storage Performance of a MoS2/Carbon Cloth Composite
by Xintong Li, Chonggui Li and Qi Yang
Materials 2023, 16(24), 7678; https://doi.org/10.3390/ma16247678 - 17 Dec 2023
Viewed by 977
Abstract
In this study, 1T phase MoS2 nanosheets were synthesized on the surface of a carbon cloth via a hydrothermal reaction. After heat treatment, the 1T phase MoS2 was transformed into the 2H phase with a better capacity retention performance. As an [...] Read more.
In this study, 1T phase MoS2 nanosheets were synthesized on the surface of a carbon cloth via a hydrothermal reaction. After heat treatment, the 1T phase MoS2 was transformed into the 2H phase with a better capacity retention performance. As an anode material for lithium-ion batteries, 2H phase MoS2 on the carbon cloth surface delivers a capacity of 1075 mAh g−1 at a current density of 0.1 A g−1 after 50 cycles; while the capacity of the 1T phase MoS2 on the surface of the carbon cloth without heat treatment fades to 528 mAh g−1. The good conductivity of a carbon cloth substrate and the separated MoS2 nanosheets help to increase the capacity of MoS2 and decrease its charge transfer resistance and promote the diffusion of lithium ions in the electrode. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

11 pages, 2258 KiB  
Article
Tailoring a N-Doped Nanoporous Carbon Host for a Stable Lithium Metal Anode
by In-Hwan Lee, Yongsheng Jin, Hyeon-Sik Jang and Dongmok Whang
Nanomaterials 2023, 13(23), 3007; https://doi.org/10.3390/nano13233007 - 23 Nov 2023
Cited by 1 | Viewed by 1150
Abstract
Li metal is a promising anode candidate due to its high theoretical capacity and low electrochemical potential. However, dendrite formation and the resulting dead Li cause continuous Li consumption, which hinders its practical application. In this study, we realized N-doped nanoporous carbon for [...] Read more.
Li metal is a promising anode candidate due to its high theoretical capacity and low electrochemical potential. However, dendrite formation and the resulting dead Li cause continuous Li consumption, which hinders its practical application. In this study, we realized N-doped nanoporous carbon for a stable Li metal host composed only of lightweight elements C and N through the simple calcination of a nitrogen-containing metal–organic framework (MOF). During the calcination process, we effectively controlled the amount of lithophilic N and the electrical conductivity of the N-doped porous carbons to optimize their performance as Li metal hosts. As a result, the N-doped porous carbon exhibited excellent electrochemical performances, including 95.8% coulombic efficiency and 91% capacity retention after 150 cycles in a full cell with an LFP cathode. The N-doped nanoporous carbon developed in this study can realize a stable Li metal host without adding lithium ion metals and metal oxides, etc., which is expected to provide an efficient approach for reliable Li metal anodes in secondary battery applications. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

14 pages, 10386 KiB  
Article
High-Rate One-Dimensional α-MnO2 Anode for Lithium-Ion Batteries: Impact of Polymorphic and Crystallographic Features on Lithium Storage
by Hye-min Kim, Byung-chul Cha and Dae-wook Kim
Nanomaterials 2023, 13(20), 2808; https://doi.org/10.3390/nano13202808 - 23 Oct 2023
Cited by 1 | Viewed by 1890
Abstract
Manganese dioxide (MnO2) exists in a variety of polymorphs and crystallographic structures. The electrochemical performance of Li storage can vary depending on the polymorph and the morphology. In this study, we present a new approach to fabricate polymorph- and aspect-ratio-controlled α-MnO [...] Read more.
Manganese dioxide (MnO2) exists in a variety of polymorphs and crystallographic structures. The electrochemical performance of Li storage can vary depending on the polymorph and the morphology. In this study, we present a new approach to fabricate polymorph- and aspect-ratio-controlled α-MnO2 nanorods. First, δ-MnO2 nanoparticles were synthesized using a solution plasma process assisted by three types of sugars (sucrose, glucose, and fructose) as reducing promoters; this revealed different morphologies depending on the nucleation rate and reaction time from the molecular structure of the sugars. Based on the morphology of δ-MnO2, the polymorphic-transformed three types of α-MnO2 nanorods showed different aspect ratios (c/a), which highly affected the transport of Li ions. Among them, a relatively small aspect ratio (c/a = 5.1) and wide width of α-MnO2-S nanorods (sucrose-assisted) induced facile Li-ion transport in the interior of the particles through an increased Li-ion pathway. Consequently, α-MnO2-S exhibited superior battery performance with a high-rate capability of 673 mAh g−1 at 2 A g−1, and it delivered a high reversible capacity of 1169 mAh g−1 at 0.5 A g−1 after 200 cycles. Our findings demonstrated that polymorphs and crystallographic properties are crucial factors in the electrode design of high-performance Li-ion batteries. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

14 pages, 5035 KiB  
Article
Carbon Nanofibers Decorated by MoS2 Nanosheets with Tunable Quantity as Self-Supporting Anode for High-Performance Lithium Ion Batteries
by Liyan Dang, Yapeng Yuan, Zongyu Wang, Haowei Li, Rui Yang, Aiping Fu, Xuehua Liu and Hongliang Li
Nanomaterials 2023, 13(19), 2689; https://doi.org/10.3390/nano13192689 - 30 Sep 2023
Cited by 3 | Viewed by 1191
Abstract
Two-dimensional molybdenum disulfide (MoS2) is considered as a highly promising anode material for lithium-ion batteries (LIBs) due to its unique layer structure, large plane spacing, and high theoretical specific capacity; however, the overlap of MoS2 nanosheets and inherently low electrical [...] Read more.
Two-dimensional molybdenum disulfide (MoS2) is considered as a highly promising anode material for lithium-ion batteries (LIBs) due to its unique layer structure, large plane spacing, and high theoretical specific capacity; however, the overlap of MoS2 nanosheets and inherently low electrical conductivity lead to rapid capacity decay, resulting in poor cycling stability and low multiplicative performance. This severely limits its practical application in LIBs. To overcome the above problems, composite fibers with a core//sheath structure have been designed and fabricated. The sheath moiety of MoS2 nanosheets is uniformly anchored by the hydrothermal treatment of the axial of carbon nanofibers derived from an electrospinning method (CNFs//MoS2). The quantity of the MoS2 nanosheets on the CNFs substrates can be tuned by controlling the amount of utilized thiourea precursor. The influence of the MoS2 nanosheets on the electrochemical properties of the composite fibers has been investigated. The synergistic effect between MoS2 and carbon nanofibers can enhance their electrical conductivity and ionic reversibility as an anode for LIBs. The composite fibers deliver a high reversible capacity of 866.5 mA h g−1 after 200 cycles at a current density of 0.5 A g−1 and maintain a capacity of 703.3 mA h g−1 after a long cycle of 500 charge–discharge processes at 1 A g−1. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Graphical abstract

14 pages, 3583 KiB  
Article
Enhancing the Electrochemical Performance of High Voltage LiNi0.5Mn1.5O4 Cathode Materials by Surface Modification with Li1.3Al0.3Ti1.7(PO4)3/C
by Tingting Yang, Chi-Te Chin, Ching-Hsiang Cheng and Jinsheng Zhao
Nanomaterials 2023, 13(4), 628; https://doi.org/10.3390/nano13040628 - 5 Feb 2023
Cited by 1 | Viewed by 2563
Abstract
A novel method for surface modification of LiNi0.5Mn1.5O4 (LNMO) was proposed, in which a hybrid layer combined by Li1.3Al0.3Ti1.7(PO4)3 (LATP) and carbon (C) composite on LNMO material were connected [...] Read more.
A novel method for surface modification of LiNi0.5Mn1.5O4 (LNMO) was proposed, in which a hybrid layer combined by Li1.3Al0.3Ti1.7(PO4)3 (LATP) and carbon (C) composite on LNMO material were connected by lithium iodide. Structure and morphology analyses illustrated that a higher contact area of active substances was achieved by the LATP/C composite layer without changing the original crystal structure of LNMO. XPS analysis proved that I promoted the reduction of trace Mn4+, resulting in a higher ion conductivity. Galvanostatic charge–discharge tests exhibited the capacity of the LNMO with 5% LATP/C improved with 35.83% at 25 °C and 95.77% at 50 °C, respectively, compared with the bare after 100 cycles, implying the modification of high-temperature deterioration. EIS results demonstrated that one order of magnitude of improvement of the lithium-ion diffusion coefficient of LATP/C-LNMO was achieved (3.04 × 10−11 S cm−1). In conclusion, the effective low-temperature modification strategy improved the ionic and electronic conductivities of the cathode and suppressed the side reactions of high-temperature treatment. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

15 pages, 3939 KiB  
Article
Facile Construction of Porous ZnMn2O4 Hollow Micro-Rods as Advanced Anode Material for Lithium Ion Batteries
by Yuyan Wang, Senyang Xu, Yamin Zhang, Linrui Hou and Changzhou Yuan
Nanomaterials 2023, 13(3), 512; https://doi.org/10.3390/nano13030512 - 27 Jan 2023
Cited by 5 | Viewed by 1868
Abstract
Spinel ZnMn2O4 is considered a promising anode material for high-capacity Li-ion batteries due to their higher theoretical capacity than commercial graphite anode. However, the insufficient cycling and rate properties seriously limit its practical application. In this work, porous ZnMn2 [...] Read more.
Spinel ZnMn2O4 is considered a promising anode material for high-capacity Li-ion batteries due to their higher theoretical capacity than commercial graphite anode. However, the insufficient cycling and rate properties seriously limit its practical application. In this work, porous ZnMn2O4 hollow micro-rods (ZMO HMRs) are synthesized by a facile co-precipitation method coupled with annealing treatment. On the basis of electrochemical analyses, the as-obtained samples are first characterized by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and scanning electron microscopy techniques. The influences of different polyethylene glycol 400 (PEG 400) additions on the formation of the hollow rod structure are also discussed. The abundant multi-level pore structure and hollow feature of ZMO HMRs effectively alleviate the volume expansion issue, rendering abundant electroactive sites and thereby guaranteeing convenient Li+ diffusion. Thanks to these striking merits, the ZMO HMRs anode exhibits excellent electrochemical lithium storage performance with a reversible specific capacity of 761 mAh g−1 at a current density of 0.1 A g−1, and a long-cycle specific capacity of 529 mAh g−1 after 1000 cycles at 2.0 A g−1 and keep a remarkable rate capability. In addition, the assembled ZMO HMRs-based full cells deliver an excellent rate capacity, and when the current density returns to 0.05 A g−1, the specific capacity can still reach 105 mAh g−1 and remains at 101 mAh g−1 after 70 cycles, maintaining a material-level energy density of approximately 273 Wh kg−1. More significantly, such striking electrochemical performance highlights that porous ZMO HMRs could be a promising anode candidate material for LIBs. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

11 pages, 2402 KiB  
Communication
Synergetic Effect of Hybrid Conductive Additives for High-Capacity and Excellent Cyclability in Si Anodes
by Byeong-Il Yoo, Han-Min Kim, Min-Jae Choi and Jung-Keun Yoo
Nanomaterials 2022, 12(19), 3354; https://doi.org/10.3390/nano12193354 - 26 Sep 2022
Cited by 6 | Viewed by 2678
Abstract
Silicon is a promising anode material that can increase the theoretical capacity of lithium-ion batteries (LIBs). However, the volume expansion of silicon remains a challenge. In this study, we employed a novel combination of conductive additives to effectively suppress the volume expansion of [...] Read more.
Silicon is a promising anode material that can increase the theoretical capacity of lithium-ion batteries (LIBs). However, the volume expansion of silicon remains a challenge. In this study, we employed a novel combination of conductive additives to effectively suppress the volume expansion of Si during charging/discharging cycles. Rather than carbon black (CB), which is commonly used in SiO anodes, we introduced single-walled carbon nanotubes (SWCNTs) as a conductive additive. Owing to their high aspect ratio, CNTs enable effective connection of SiO particles, leading to stable electrochemical operation to prevent volume expansion. In addition, we explored a combination of CB and SWCNTs, with results showing a synergetic effect compared to a single-component of SWCNTs, as small-sized CB particles can enhance the interface contact between the conductive additive and SiO particles, whereas SWCNTs have limited contact points. With this hybrid conductive additive, we achieved a stable operation of full-cell LIBs for more than 200 cycles, with a retention rate of 91.1%, whereas conventional CB showed a 74.0% specific capacity retention rate. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

12 pages, 3807 KiB  
Article
Growth of Nitrogen Incorporated Ultrananocrystalline Diamond Coating on Graphite by Hot Filament Chemical Vapor Deposition
by Daniel Villarreal, Jyoti Sharma, Maria Josefina Arellano-Jimenez, Orlando Auciello and Elida de Obaldía
Materials 2022, 15(17), 6003; https://doi.org/10.3390/ma15176003 - 31 Aug 2022
Cited by 2 | Viewed by 2485
Abstract
This article shows the results of experiments to grow Nitrogen incorporated ultrananocrystalline diamond (N-UNCD) films on commercial natural graphite (NG)/Cu anodes by hot chemical vapor deposition (HFCVD) using a gas mixture of Ar/CH4/N2/H2. The experiments focused on [...] Read more.
This article shows the results of experiments to grow Nitrogen incorporated ultrananocrystalline diamond (N-UNCD) films on commercial natural graphite (NG)/Cu anodes by hot chemical vapor deposition (HFCVD) using a gas mixture of Ar/CH4/N2/H2. The experiments focused on studying the effect of the pressure in the HFCVD chamber, filament-substrate distance, and temperature of the substrate. It was found that a substrate distance of 3.0 cm and a substrate temperature of 575 C were optimal to grow N-UNCD film on the graphite surface as determined by Raman spectroscopy, SEM, and TEM imaging. XPS analysis shows N incorporation through the film. Subsequently, the substrate surface temperature was increased using a heater, while keeping the substrate-filament distance constant at 3.0 cm. In this case, Raman spectra and SEM images of the substrate surface showed a major composition of graphite in the film as the substrate-surface temperature increased. Finally, the process pressure was increased to 10 Torr where it was seen that the growth of N-UNCD film occurred at 2.0 cm at a substrate temperature of 675 C. These results suggest that as the process pressure increases a smaller substrate-filament distance and consequently a higher substrate surface temperature can still enable the N-UNCD film growth by HFCVD. This effect is explained by a mean free path analysis of the main precursors H2 and CH3 molecules traveling from the filament to the surface of the substrate The potential impact of the process developed to grow electrically conductive N-UNCD films using the relatively low-cost HFCVD process is that this process can be used to grow N-UNCD films on commercial NG/Cu anodes for Li-ion batteries (LIBs), to enable longer stable capacity energy vs. charge/discharge cycles. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

19 pages, 8203 KiB  
Article
Metal (Cu/Fe/Mn)-Doped Silicon/Graphite Composite as a Cost-Effective Anode for Li-Ion Batteries
by Arunakumari Nulu, Young Geun Hwang, Venugopal Nulu and Keun Yong Sohn
Nanomaterials 2022, 12(17), 3004; https://doi.org/10.3390/nano12173004 - 30 Aug 2022
Cited by 7 | Viewed by 3422
Abstract
Silicon is a worthy substitute anode material for lithium-ion batteries because it offers high theoretical capacity and low working potentials vs. Li+/Li. However, immense volume changes and the low intrinsic conductivity of Si hampers its practical applications. In this study, nano/micro [...] Read more.
Silicon is a worthy substitute anode material for lithium-ion batteries because it offers high theoretical capacity and low working potentials vs. Li+/Li. However, immense volume changes and the low intrinsic conductivity of Si hampers its practical applications. In this study, nano/micro silicon particles are achieved by ball milling silicon mesh powder as a scalable process. Subsequent metal (Cu/Fe/Mn) doping into nano/micro silicon by low-temperature annealing, followed by high-temperature annealing with graphite, gives a metal-doped silicon/graphite composite. The obtained composites were studied as anodes for Li-ion batteries, and they delivered high reversible capacities of more than 1000 mAh g−1 with improved Li+ diffusion properties. The full cells from these composite anodes vs. LiCoO2 cathodes delivered suitable energy densities for Li+ storage applications. The enhanced electrochemical properties are accredited to the synergistic effect of metal doping and graphite addition to silicon and exhibit potential for suitable Li+ energy storage applications. Full article
(This article belongs to the Topic Advanced Nanomaterials for Lithium-Ion Batteries)
Show Figures

Figure 1

Back to TopTop