Search Results (334)

The objective of this study was to investigate the influence of the lignocellulose filler originating in wood and non-wood raw materials, alone or together with collagen hydrolysate, on the properties and biodegradation ability of natural rubber latex. The different hydrophobicity of the polymer matrix and natural filler makes it difficult to obtain a homogenous structure of the composite. However, the easy biodegradation of the natural filler is a sufficient reason to seek a compromise between its useful properties and the environmental safety of the material. The composites were filled with lignocellulose filler: pine, spruce, and birch wood flour or willow, raspberry, and mallow non-wood flour. Collagen hydrolysate was used as a substitute for lignocellulosic filler, together or alone. The mechanical properties of the composites, their hardness, and equilibrium swelling were studied. In order to determine the morphology and interactions between filler and latex, scanning electron microscopy together with infrared spectroscopy were engaged. The results revealed that after the incorporation of 4 phr of the filler, the increase in mechanical strength was observed even despite the lack of compatibility between the filler and polymer matrix. The lignocellulose filler is a promising agent because its biodegradability contributes to the overall environmental safety of the polymer material. Full article

Wood polymer composites (WPCs) represent a rapidly growing class of sustainable materials, formed by combining lignocellulosic fibers with thermoplastic or thermoset polymeric matrices. This review summarizes the state of the art in WPC development, emphasizing the use of recyclable (or recycled) and biodegradable polymers as matrix materials. The integration of waste wood particles into the production of WPCs addresses global environmental challenges, including plastic pollution and deforestation, by offering an alternative to conventional wood-based and petroleum-based products. Key topics covered in the review include raw material sources, fiber pre-treatments, compatibilizers, mechanical performance, water absorption behavior, thermal stability and end-use applications. Full article

The development of sustainable and functional nanocomposites has attracted considerable attention in recent years due to their broad spectrum of potential applications, including wood preservation. Also, a global goal is to reuse the large volumes of waste for environmental issues. In this context, the aim of the study was to obtain soda lignin particles, to graft ZnO nanoparticles onto their surface and to apply these hybrids, embedded into a biodegradable polymer matrix, as protection/preservation coating for oak wood. The organic–inorganic hybrids were characterized in terms of compositional, structural, thermal, and morphological properties that confirm the efficacy of soda lignin extraction and ZnO grafting by physical adsorption onto the decorating support and by weak interactions and coordination bonding between the components. The developed solution based on poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and lignin-ZnO was applied to oak wood specimens by brushing, and the improvement in hydrophobicity (evaluated by water absorption that decreased by 48.8% more than wood, humidity tests where the treated sample had a humidity of 4.734% in comparison with 34.911% for control, and contact angle of 97.8° vs. 80.5° for untreated wood) and UV and fungal attack protection, while maintaining the color and aspect of specimens, was sustained. L.ZnO are well dispersed into the polymer matrix, ensuring a smooth and less porous wood surface. According to the results, the obtained wood coating using both a biodegradable polymeric matrix and a waste-based preservative can be applied for protection against weathering degradation factors, with limited water uptake and swelling of the wood, UV shielding, reduced wood discoloration and photo-degradation, effective protection against fungi, and esthetic quality. Full article

Biodegradable polymer composites offer promising alternatives to petroleum-based plastics, supporting the principles of a zero waste and circular economy. This study investigates the reinforcing potential of alkali-treated wood flour derived from recycled pine (Pinus brutia Ten.) and poplar (Populus alba L.) waste wooden pallets in poly(lactic acid) (PLA) biocomposites. Wood flour was initially recovered through grinding and screening during recycling, followed by alkali treatment via a green chemistry approach to enhance interfacial bonding with the PLA matrix. The impact of alkali concentration and two fabrication methods—additive manufacturing (AM) and injection molding (IM)—on the properties of developed biocomposite materials was assessed through mechanical, physical, morphological, and thermal analyses. IM samples outperformed AM counterparts, with the IM PLA containing 30 wt% wood flour (alkali-treated with 10% solution) showing the highest mechanical gains: tensile (+71.35%), flexural (+64.74%), and hardness (+2.62%) compared to untreated samples. Moreover, the AM sample with 10 wt% wood flour and 10% alkali treatment showed a 49.37% decrease in water absorption compared to the untreated sample, indicating improved hydrophobicity. Scanning electron microscopy confirmed that alkali treatment reduced void content and enhanced morphological uniformity, while thermal properties remained consistent across fabrication methods. This work introduces a green composite using non-toxic materials and treatments, facilitating eco-friendly production aligned with zero waste and circular economy principles throughout the manufacturing lifecycle. Full article

This study investigated the effect of in situ polymerization on the compressive strength of demolition-derived Scots pine, European beech, and black alder wood. The treatment applied was based on previously confirmed in situ polymerization systems in wood, which are known to lead to polymer formation and composite-like structures. In this study, we assumed similar behavior and focused on a mechanical evaluation of the modified wood. Three different polymer systems were applied to evaluate differences in performance. After modification, the compressive strength levels increased by 60% in beech, 119% in alder, and 150% in pine, with corresponding increases in density and weight percent gain (WPG). The highest relative improvement was observed in the least dense species, pine. The findings suggest that polymer treatment can significantly enhance the mechanical properties, likely due to the incorporation of polymer into the wood matrix; however, this inference is based on indirect physical evidence. Full article

The environmental impact of petroleum-based plastics has driven a global shift toward sustainable alternatives like biodegradable polymers, including polylactic acid (PLA), polybutylene succinate (PBS), and polycaprolactone (PCL). Yet, these bioplastics often face limitations in mechanical and thermal properties, hindering broader use. Reinforcement with cellulose nanofibrils (CNFs) has shown promise, yet most research focuses on conventional sources like wood pulp and cotton, neglecting agricultural residues. This review addresses the potential of maize husk, a lignocellulosic waste abundant in South Africa, as a source of CNFs. It evaluates the literature on the structure, extraction, characterisation, and integration of maize husk-derived CNFs into biodegradable polymers. The review examines the chemical composition, extraction methods, and key physicochemical properties that affect performance when blended with PLA, PBS, or PCL. However, high lignin content and heterogeneity pose extraction and dispersion challenges. Optimised maize husk CNFs can enhance the mechanical strength, barrier properties, and thermal resistance of biopolymer systems. This review highlights potential applications in packaging, biomedical, and agricultural sectors, aligning with South African bioeconomic goals. It concludes by identifying research priorities for improving compatibility and processing at an industrial scale, paving the way for maize husk CNFs as effective, locally sourced reinforcements in green material innovation. Full article

The growing demand for sustainable materials has intensified the search for biodegradable polymers. Poly(ε-caprolactone) (PCL), though biodegradable, is fossil-derived. In this study, a novel lignin extracted from pine wood using a green solvent was incorporated into PCL and compared with commercial lignins (dealkaline, alkaline, and lignosulfonate). The lignin additions imparted antioxidant properties, enhanced thermal stability, and promoted circular economy goals through lignin valorization. Notably, the green-extracted lignin showed superior compatibility with PCL when compared with commercial lignins, as evidenced by lower water uptake and solubility, and improved surface hydrophobicity (higher contact angle). Although the addition of lignin reduced the tensile strength and elongation at break, it greatly increased the PCL radical scavenging activity (DPPH) from 8 ± 1% of neat PCL to 94.8 ± 0.3% when 20 wt% of lignin-LA was added. Among the tested lignins, lignin-LA stands out as the most promising candidate to be applied as a functional additive in biodegradable polymer blends and composites for advanced sustainable applications. Not only given its intrinsically higher sustainability but also due to its capacity for improving the thermal properties of PCL–lignin blends. Full article

This study utilizes waste wheat straw fibers and discarded tea bags as novel raw materials for developing new thermal insulation and sound absorption composites. Wood adhesive (WA) is used to bind the polymer raw materials. Loose polymers and different composites are experimentally developed in different concentrations. Sound absorption and thermal conductivity coefficients are obtained for the developed boards. Bending moment analysis and the moisture content of the boards are reported in addition to a microstructure analysis of the straw fibers from wheat. The results indicate that as the wheat straw fiber’s percentage increases in the composite, the thermal conductivity coefficient decreases, the flexure modulus decreases, the sound absorption coefficient increases at some frequencies, and the moisture content increases. The range of thermal conductivity and the noise reduction coefficient are 0.042–0.073 W/m K and 0.35–0.6 at 24 °C for the polymer raw materials, respectively. The corresponding values for the composites are 0.054 and 0.0575 W/m K and 0.45–0.5, respectively. The maximum moisture content percentages for the polymers and composites are 6.5 and 1.15, respectively. The composite flexure modulus reaches maximum and minimum values of 4.59 MPa and 2.22 MPa, respectively. These promising results promote these polymer and composite sample boards as more convenient insulation materials for green buildings and could replace the conventional petrochemical thermal insulation ones. Full article

Plant-particle-reinforced polymer composite products are widely used in construction. New terrace profiles, reinforced with oat or millet husks, are being considered. However, their resistance to wood-decomposing Agaricomycetes fungi requires investigation due to their intended environmental exposure. Susceptibility to Coniophora puteana, Coriolus versicolor, and Gleophyllum trabeum was tested. Well-known rice-husk-reinforced profiles were used as the reference material for the analysis. The bioresistance of the oat-husk-reinforced profiles was similar to that of the reference profile. Minor mycelium development and changes in the surface morphology, mass, and flexural strength were found. Millet husk-reinforced profiles showed greater fungal susceptibility, questioning their suitability for the intended application. Coniophora puteana was the most aggressive among all the profiles. Full article

Wood–textile composites (WTCs), consisting of polypropylene and woven willow wood, have potential for both interior and exterior applications. However, their basic materials are not inherently resistant to outdoor weathering. This study examines the impact of various climatic conditions on the material behavior of WTCs. The composite and its components were aged under different scenarios, including kiln-drying, frost, standard and tropical climate, and artificial weathering and water storage, and analyzed for dimensional stability, chemical changes (FTIR), mechanical damage (µ-CT), and mechanical performance. While kiln-drying, frost, and tropical climates had only minor effects, water storage caused swelling-related damage, resulting in a 45% decrease in Young’s modulus but increased elongation at break (+88%) and impact strength (+75%). Artificial weathering led to significant degradation: tensile strength declined by 28%, Young’s modulus by 49%, and impact strength by 26%. In the medium term, this degradation compromises the integrity of the composite. The results highlight the need for effective stabilization measures—such as polymer modification or structural protection—to ensure the long-term durability of WTCs in outdoor use. Full article

In this study, a flame-retardant wood-polymer composite was produced using huntite-hydromagnesite mineral, recognized for its non- flammability properties. In this context, wood-polymer composites were produced with the co-rotating twin-screw extrusion technique, while polypropylene was applied as the composite matrix, medium density fiberboard waste and inorganic huntite-hydromagnesite mineral were used as the reinforcement material. The proportion of wood powder additives was changed to 10% and 20%, and the huntite and hydromagnesite ratio was changed to 30%, 40%, 50% and 60%. Maleic anhydride grafted polypropylene, i.e., MAPP, was applied as a binder at a rate of 3%. Polypropylene, wood fibers, mineral powders, and MAPP blended in the mixer were processed in the extruder and turned into granules. Structural, morphological, thermal, mechanical, and flame-retardant properties of the composites were analyzed using XRD, SEM, FTIR, TGA, tensile testing, and the UL-94 vertical flammability test. Test samples were prepared to evaluate the physical and mechanical properties with a compression molding machine. It was concluded that the composites gained significant flame retardancy with the addition of huntite hydromagnesite. The potential for using this material in various fields and its compliance with the principles of circular economy and the Sustainable Development Goals (SDG 12) were noted. Full article

There is a sizeable amount of sawdust produced from wood industries such as timber and furniture. In the past, sawdust has been utilized as a fuel source and in the manufacturing of furniture. Based on the limited use of sawdust, there is plenty of sawdust accessible from the industries. Sawdust is the material of choice due to its cost effectiveness, environmental friendliness, and biodegradability. However, if sawdust is not appropriately disposed or utilized better, it may have negative impact on the aquatic life and organic products. Hence, this review paper discusses the best possible methods or proper routes for the utilization of sawdust to benefit the environment, society, and the economy at large. Sawdust possesses superior capabilities as a reinforcing filler in various polymer matrices for advanced applications. This paper provides an in-depth discussion on sawdust hybrid composites in comparison to other natural fibres hybrid composites. The applications of various sawdust hybrid polymer composites for specific systems are also mentioned. Furthermore, the morphology and preparation of the sawdust/polymer composites and/or sawdust hybrid polymers composites are also discussed since it is well known that the properties of the natural fibre composites are affected by the preparation method and the resultant morphology. Based on the above, the current paper also plays a critical role in providing more information about waste to value added products. Full article

The effect of epoxidized soybean oil on the operational, technological, and physical and mechanical properties of composites based on high-density recycled polyethylene filled with wood floor was investigated. It has been shown that the introduction of epoxidized soybean oil in the amount of 0.5 wt.% into the wood-polymer composite (WPC) improves the physical, mechanical, and operational properties of the material: the Charpy impact strength (on notched samples) increases from 7.5 kJ/m² to 20.0 kJ/m², the bending strength increases from 31.6 MPa to 50.8 MPa, and the coefficient of linear thermal expansion decreases by 15%. With a further increase in the content of epoxidized soybean oil in the composite, its water absorption and technological shrinkage decrease, but its physical and mechanical properties deteriorate. Full article

This paper presents an experimental investigation of six different types of composite sandwich panels manufactured from waste-based materials, which are comprised of two different types of skins (made from hemp and recycled PET (Polyethylene terephthalate) fabrics with bio-epoxy resin) and three different cores (composite wood, recycled plastic, and styrofoam) materials. The skins of these sandwich panels were investigated under five different environmental conditions (normal air, water, hygrothermal, saline solution, and 80 °C elevated temperature) over seven months to evaluate their durability performance. In addition, the tensile and dynamic mechanical properties of those sandwich panels were studied. The bending behavior of cores and sandwich panels was also investigated and compared. The results indicated that elevated temperatures are 30% more detrimental to fiber composite laminates than normal water. Composite laminates made of hemp are more sensitive to environmental conditions than composite laminates made of recycled PET. A higher-density core makes panels more rigid and less susceptible to indentation failure. The flexible plastic cores are found to be up to 25% more effective at increasing the strength of sandwich panels than brittle wood cores. Full article

In the case of load increases and the refurbishment of existing buildings, it is often necessary to carry out strengthening measures on existing timber beams. When timber concrete composite (TCC) ceilings cannot be used, it is possible to reinforce the undersides of the beams with structural steel or fiber composites (aramid or carbon-fiber-reinforced polymer). This work investigates how significant effects on the load-bearing and deformation behavior can be achieved with these materials in terms of construction practice. The article is intended to show structural engineers which reinforcement measures lead to which forces, deformations, etc., and how these are utilized. This should form the basis for the planning of reinforcement measures, as it is not clear from the beginning whether AFRP, CFRP, or steel is the most suitable material. For this purpose, a comparative parameter study was carried out under practical conditions and with a variable degree of reinforcement using the corresponding formulas. The internal forces in the timber and reinforcement cross-sections, the deflection behavior, and the failure loads at the strength and design levels were calculated. It was demonstrated that, particularly for steel and carbon-fiber-reinforced polymer (CFRP) reinforcements, significant increases in the ultimate load can be achieved and the often-important deformation behavior can be significantly improved. Especially the steel variant leads to high improvements in deflection and breaking load behavior, with the base material (wood) also being utilized more economically as a result. A comparative ecological study in the form of the global warming potential showed that reinforcement methods are also advantageous from the point of view of sustainability compared to renovations with timber concrete composite slabs or new concrete slabs. Full article