Search Results (133)

The present study focuses on recovering phenolic compounds and terpenes from olive leaves, which are generated as by-products during olive oil processing. To this end, conventional extraction/maceration (CE) and advanced extraction techniques such as subcritical water extraction (SWE), pressurized fluid extraction (PLE) and ultrasound-assisted extraction (UAE) were employed to compare and determine the most effective procedure. The phenolic and terpenoid composition of the extracts revealed a total of 33 compounds in HPLC-QTOF-MS analysis. According to these findings, the optimal extraction techniques for the maximum recovery of secoiridoids from olive leaves were PLE and UAE, with no significant difference between them (21.9891 ± 2.5521 mg/g DW and 21.0888 ± 1.3494 mg/g DW, respectively). Regarding to flavonoids, UAE was the most effective extraction technique, yielding 4.9837 ± 0.6739 mg/g DW. However, SWE recovered the highest amount of phenolic alcohols (7.4201 ± 0.9848 mg/g DW), which could be due to degradation of the secoiridoids during extraction. Conversely, UAE was more successful than the other techniques for the extraction of the terpene family (0.7373 ± 0.0601 mg/g DW). The present study therefore focuses on comparing different extraction techniques for revalorizing olive leaves as a source of bioactive compounds, specifically polyphenols and terpenes, due to their beneficial health properties. Full article

Pectin is a multifunctional polysaccharide whose structural attributes, including degree of esterification (DE), molecular weight (MW), and branching, directly affect its gelling, emulsifying, and bioactive properties. Conventional pectin extraction relies on acid- or alkali-based methods that degrade the pectin structure, generate chemical waste, and alter its physicochemical and functional properties. Although novel methods such as ultrasound-assisted extraction (UAE), microwave-assisted extraction (MAE), and enzyme-assisted extraction (EAE) are recognized as environmentally friendly alternatives, they frequently use acids or alkalis as solvents. This review focuses on pectin extraction methods that do not involve acidic or alkaline solvents such as chelating agents, super/subcritical water, and deep eutectic solvents (DESs) composed of neutral components. This review also discusses how these alternative extraction methods can preserve or modify the key structural features of pectin, thereby influencing its monosaccharide composition, molecular conformation, and interactions with other biopolymers. Furthermore, the influence of these structural variations on the rheological properties, gelling behaviors, and potential applications of pectin in the food, pharmaceutical, and biomedical fields are discussed. This review provides insights into alternative strategies for obtaining structurally intact and functionally diverse pectin by examining the relationship between the extraction conditions and pectin functionality. Full article

Rail transit as a high-energy consumption field urgently requires the adoption of clean energy innovations to reduce energy consumption and accelerate the transition to new energy applications. As an energy-saving fluid machinery, the ejector exhibits significant application potential and academic value within this field. This paper reviewed the recent advances, technical challenges, research hotspots, and future development directions of ejector applications in rail transit, aiming to address gaps in existing reviews. (1) In waste heat recovery, exhaust heat is utilized for propulsion in vehicle ejector refrigeration air conditioning systems, resulting in energy consumption being reduced by 12~17%. (2) In vehicle pneumatic pressure reduction systems, the throttle valve is replaced with an ejector, leading to an output power increase of more than 13% and providing support for zero-emission new energy vehicle applications. (3) In hydrogen supply systems, hydrogen recirculation efficiency exceeding 68.5% is achieved in fuel cells using multi-nozzle ejector technology. (4) Ejector-based active flow control enables precise ± 20 N dynamic pantograph lift adjustment at 300 km/h. However, current research still faces challenges including the tendency toward subcritical mode in fixed geometry ejectors under variable operating conditions, scarcity of application data for global warming potential refrigerants, insufficient stability of hydrogen recycling under wide power output ranges, and thermodynamic irreversibility causing turbulence loss. To address these issues, future efforts should focus on developing dynamic intelligent control technology based on machine learning, designing adjustable nozzles and other structural innovations, optimizing multi-system efficiency through hybrid architectures, and investigating global warming potential refrigerants. These strategies will facilitate the evolution of ejector technology toward greater intelligence and efficiency, thereby supporting the green transformation and energy conservation objectives of rail transit. Full article

In the present study, three-dimensional turbulent, subcritical open-channel flow (Fr = 0.19) through submerged rigid vegetation is numerically investigated using the ANSYS FLUENT solver (v. 22. 1). The Volume of Fluid (VOF) method is applied for free-surface tracking, while the standard k-ε turbulence model is employed for turbulence closure. Vegetation is modeled as vertical rigid cylinders fixed at the bottom of the channel. Regarding the arrangement of the stems, two cases are examined. In the first case, a linear arrangement of three equally spaced vegetative stems is located transversely at the center of the channel, while in the second case, a parallel arrangement of fifteen equidistant vegetative stems is located downstream of the channel center. In both cases, the vertical velocity profile within the submerged vegetation layer deviates significantly from that of the upper non-vegetated layer, which generally adheres to the logarithmic velocity distribution. In the second case, flow field repeatability is observed after the third stem series, particularly in terms of velocity profiles. Additionally, the structure of turbulence is noticeably affected in the vicinity of the stems, resulting in higher eddy viscosity values near each stem’s crest area. Furthermore, a localized drop in the free surface is recorded above the vegetated region, while a slight rise is observed upstream of each stem series, consistent with subcritical open-channel flow. Full article

The global demand for oils and lipids, particularly those derived from vegetable sources with high polyunsaturated fatty acid content, has posed significant challenges for the food industry. This trend is largely driven by growing consumer awareness of health and nutrition. To meet this demand, it is essential to not only identify richer sources of lipids but also develop efficient, sustainable, and environmentally friendly methods for their extraction, isolation, and characterization. In this context, the present work provides a comprehensive review of current perspectives on the extraction, isolation, and identification of lipids and fatty acids, comparing conventional and green methodologies for food applications. Ideally, analytical and processing methodologies for obtaining food-grade materials should prioritize low energy consumption, minimal or no use of hazardous substances, and the generation of non-polluting residues, thereby safeguarding both human health and the environment. In recent years, green extraction techniques have emerged as promising alternatives to conventional methods, offering partial or complete replacements, such as ultrasound-assisted extraction, microwave-assisted extraction, supercritical and subcritical fluid extraction, and others. However, significant advancements are still required to fully address these concerns. Techniques such as chromatography and spectrometry play pivotal roles in the isolation and identification process, especially gas chromatography coupled with mass spectrometry or with flame ionization detectors; while separating individual fatty acids based on their chain length and degree of unsaturation, reversed-phase high-performance liquid chromatography (HPLC) is quite a helpful approach. Furthermore, the isolation and structural elucidation of fatty acids are critical steps in ensuring the nutritional quality and commercial viability of lipid products. Full article

This study presents a new approach to chemical processing using pyridine-based solvolysis to produce high-quality glass fiber from epoxy composites. Pyridine was chosen due to its solubility parameter, which precisely matches the parameters calculated for the epoxy matrix segment. Experiments with exposure in a pyridine medium demonstrated effective swelling and the potential for destruction. The solvolysis experiments were conducted in a round-bottomed flask with a reflux condenser and stirrer, under ambient conditions (20 °C) until the boiling point was reached (115.2 °C). Additionally, data from experimental studies conducted at subcritical temperatures before reaching 280 °C are presented. The dependences of changes in the mass of composites on time and temperature during the solvolysis process were determined. The tensile strength of the recovered fibers was examined, and thermogravimetric analysis was used to determine their properties. Fiberglass recovered at the boiling point is characterized by 91% tensile strength and 20% residual degradation products on the surface. The residual strength of fiberglass-reinforced plastic (FGRP) is 70.3%. The use of subcritical pyridine helps improve the quality of plastic products made from recycled fibers. This process retains 93% of the residual tensile strength for fibers that have been processed at 250 °C for two hours. Recycled fibers also contain 2.82% organic components on their surfaces. Using this material results in an increase in flexural strength of FGRP by 16.1%, compared to the reference samples. Full article

Climate change is a global issue that has gained much attention recently. Co-firing biomass with coal/waste coal reduces the electricity sector’s GHG emissions sustainably. This study uses commercial software to model waste coal and biomass co-firing in 100 MW and 600 MW power plants. The objective is to assess the effects of fluid types (subcritical and supercritical), plant capacities (100 MW and 600 MW), boiler types (pulverized coal and circulating fluidized bed boilers), biomass and waste coal co-firing ratios (0:100, 20:80, 40:60, 60:40, 80:20, and 100:0), and carbon capture and storage efficiencies (0%, 90%, 95%, and 97%) on performance parameters such as net plant efficiency, heat rate, net plant CO₂ and SO₂, and particulate matter emissions. The feedstocks selected for this investigation include anthracite waste coal and loblolly pine biomass. As the biomass fraction increases from 0% to 100%, co-fired power plants net efficiency increases by 3–8%. Supercritical plants had a 6% higher net plant efficiency than the subcritical plants. The study found that the biomass’s high heating value decreased the fuel flow rate and reduced plant CO₂ emissions by 10–16%. With 100% biomass power plant feed and 90% carbon capture and storage efficiency, CO₂ emissions drop by 83% and SO₂ and PM emissions drop to zero. Full article

The selective separation of aromatics from slurry oil (SLO)—a low-value byproduct of fluid catalytic cracking—remains a major industrial challenge. This study investigates the use of subcritical water (Sub-CW) as a green and tunable solvent to extract aromatics from SLO in a semi-batch system operating at 250–325 °C. At 325 °C and a water-to-oil mass ratio of 6:1, the extract yield reaches 16 wt%, with aromatic hydrocarbons accounting for over 90 wt% of the extract, predominantly composed of 3- to 4-ring polycyclic aromatic hydrocarbons. Comprehensive characterization via simulated distillation, SARA analysis, FT-IR, and ¹H-NMR confirms the selective enrichment of aromatics and effective separation from saturates and asphaltenes. To elucidate the molecular basis of this selectivity, principal component analysis of Hansen solubility parameters was performed. The results revealed a temperature-dependent solubility trend in Sub-CW, whereby the affinity for hydrocarbons follows the order aromatics > cycloalkanes > alkanes. This solubility preference, supported by both experimental data and theoretical analysis, offers new insight into subcritical solvent design and provides a basis for process intensification in SLO valorization. Full article

Using hydrogen as a working fluid in cryocoolers can potentially benefit cryocooling technologies and hydrogen liquefaction. Moreover, in flow-through thermoacoustic systems, hydrogen can be efficiently cooled and undergo ortho-parahydrogen isomeric conversion, which is important for the efficient storage of cryogenic hydrogen. A traveling-wave regenerator is analyzed in this study, using the thermoacoustic theory with a superimposed mean flow and an empirical correlation for hydrogen isomer conversion. A regenerator with hydrogen fluid is shown to achieve higher performance in comparison with helium as the working fluid. However, the hydrogen system performance degrades at supercritical pressures and subcritical temperatures in compressed liquid states. In regenerators with mean flow, using hydrogen as the working fluid leads to higher cooling powers and efficiencies, but helium systems are able to achieve colder temperatures. Full article

To fully recover abundant waste heat and reduce the operation cost in liquid-cooled data centers, a Carnot battery consisting of a heat pump (HP) and organic Rankine cycle (ORC) is proposed. Due to the existence of different cycle states for HPs and ORCs, four different cycle combinations are considered. To evaluate and compare their performances, thermo-economic models are developed. Under the design conditions, the optimal working fluid combinations are first determined for each battery. On this basis, thermodynamic and economic performances of the four batteries are analyzed in detail. The results indicate that the system consisting of a subcritical HP/transcritical ORC achieves the highest round-trip efficiency at 76%. Notably, the round-trip efficiency of the system can exceed 100% at low ORC condensing temperatures. Additionally, the system cost is about 767–796 USD/kW∙h, depending on the cycle combinations. Furthermore, the effects of operating parameters on system performances are also investigated. Finally, with the objective of maximum round-trip efficiency, key parameters of four batteries are optimized. The results reveal that the system with a subcritical HP/subcritical ORC attains a maximum round-trip efficiency of 83% after optimization. These research results contribute to the development of green data centers and the reduction of power costs. Full article

Propolis is a valuable natural resource for extracting various beneficial compounds. This study explores a sustainable extraction approach for Brazilian green propolis. First, supercritical fluid extraction (SFE) process parameters were optimized (co-solvent: 21.11% v/v CPME, and temperature: 60 °C) to maximize yield, total phenolic content (TPC), antioxidant capacity, and LOX (lipoxygenase) inhibitory activity. GC–MS analysis identified 40 metabolites in SFE extracts, including fatty acids, terpenoids, phenolics, and sterols. After selecting the optimum SFE process parameters, a sequential high-pressure extraction (HPE) approach was developed, comprising SFE, pressurized liquid extraction (PLE) with EtOH/H₂O, and subcritical water extraction (SWE). This process was compared to a similar sequential extraction using low-pressure extractions (LPE) with a Soxhlet extractor. The HPE process achieved a significantly higher overall yield (80.86%) than LPE (71.43%). SFE showed higher selectivity, resulting in a lower carbohydrate content in the non-polar fraction, and PLE extracted nearly twice the protein amount of LPE–2. Despite the HPE selectivity, LPE extracts exhibited better acetylcholinesterase (AChE), butyrylcholinesterase (BChE), and LOX inhibition, demonstrating that the neuroprotective and anti-inflammatory activity of the extracts may be associated with a symbiosis of a set of compounds. Finally, a comprehensive greenness assessment revealed that the HPE process proved more sustainable and aligned with green chemistry principles than the LPE method. Full article

Lavender is one of the most appreciated aromatic plants, with high economic value in food, cosmetics, perfumery, and pharmaceutical industries. Lavender essential oil (LEO) is known to have demonstrative antimicrobial, antioxidant, therapeutic, flavor and fragrance properties. Conventional extraction methods, e.g., steam distillation (SD) and hydro-distillation (HD), have been traditionally employed to extract LEO. However, the low yield, high energy consumption, and long extraction time of conventional methods have prompted the introduction of novel extraction technologies. Some of these innovative approaches, such as ohmic-assisted, microwave-assisted, supercritical fluid, and subcritical water extraction approaches, are used as substitutes to conventional extraction methods. While other methods, e.g., sonication, pulsed electric field, and cold plasma, can be used as a pre-treatment that is preceded by conventional or emerging extraction technologies. These innovative approaches have a great significance in reducing the energy consumption, shortening the extraction time, and increasing the extraction yield and the quality of EOs. Therefore, they can be considered as sustainable extraction technologies. However, the scale-up of emerging technologies to an industrial level should also be investigated from the techno-economic points of view in future studies. Full article

Numerical simulations of sub-critical flow past a circular cylinder at Reynolds number $\mathrm{R}\mathrm{e}$ = 130,000 are performed using two numerical platforms: the commercial, Ansys Fluent, and the open-source, OpenFOAM (finite volume method and large-eddy simulation based on a differential equation for the sub-grid kinetic energy). An overview of the available experimental data and similar large-eddy simulation studies is presented. A detailed analysis of all accumulated data demonstrates satisfactory agreement between them with a dispersion of approximately $20\%$ for the main integral flow parameters. A detailed comparison of the results obtained using single- and double-precision numerical methods in Ansys Fluent did not reveal any noticeable discrepancies in the integral and local flow parameters as well as the spectral characteristics. It is shown that the behavior of the dynamic system of the fluid dynamic equations computed with single precision is stable by Lyapunov and does not lead to any loss of accuracy. The reconstructed attractors of the dynamic systems in phase space are limited by an ellipsoid. Full article

Background: The use of natural hepatoprotective remedies represents an important path in modern phytotherapy. Objectives: In this context, our research aims to evaluate the phytochemical composition and the hepatoprotective and oxidative stress reduction potential of an Arctium tomentosum Mill. root extract. Methods: The phenolic profile of the tested extract, prepared by the subcritical fluid-assisted method were qualitatively and quantitatively analyzed by spectrophotometrical and HPLC/DAD/ESI methods. In vitro antioxidant capacity was assessed using DPPH and FRAP assays. Hepatoprotective activity of the extract was assessed on a model of CCl₄ experimentally induced hepatotoxicity in mice. Results: Phytochemical assays revealed the presence of important polyphenols, such as chlorogenic acid (17.20 ± 0.65 μg/mL) and acacetin 7-O-glucoside (56.80 ± 1.66 μg/mL). In vitro, the tested extract exhibited a significant oxidative stress reduction capacity, while in vivo it showed a dose-dependent hepatoprotective effect indicated by an improvement in plasma proteins profile and down-regulation of plasma transaminase activity (ALAT, ASAT, GGT). In liver tissue, the extract partially restored the activity of GPx, CAT, and SOD and attenuated lipid peroxidation. The protective effect of the A. tomentosum root extract was supported by the alleviation of histological injuries of the liver (centrilobular necrosis, granulocytic infiltrate, and fibrosis). Conclusions: The A. tomentosum subcritical fluid-assisted root extract proved to be able to provide a significant hepatoprotective effect mainly through an antioxidant mechanism. Full article

Extraction of lipids and high-value products from highly wet microalgae requires significant energy for the drying pretreatment. In this study, we examined the direct extraction of lipids, β-carotene, and polyphenolic compounds from wet Dunaliella salina using liquefied dimethyl ether (DME), which is effective in lipid extraction for biofuel production. The amount of DME-extracted β-carotene was 7.0 mg/g, which was higher than that obtained from the chloroform–methanol extraction. Moreover, the total phenolic content extracted with DME and its antioxidant capacity were slightly higher than those extracted with chloroform–methanol. DME removed almost all the water and extracted 29.2 wt% of total lipids and 9.7 wt% of fatty acids. More lipids were extracted from wet samples by liquefied DME than by chloroform–methanol extraction. The C/N ratio of lipids extracted with DME was 112.0, higher than that of chloroform–methanol. The high C/N ratio suggests that nitrogen-containing phosphatidylcholines may be less easily extracted by liquefied DME and may be highly selective. However, the ratio of saturated fatty acids was 34.8%, lower than that of chloroform–methanol. Na⁺ and Mg²⁺ in the culture medium were not extracted using DME. Thus, using the extract with DME has both advantages and disadvantages compared to using the extract with chloroform–methanol; however, it has satisfactory extraction properties. DME is expected to be an environment-friendly alternative solvent because it does not require drying, which is necessary for conventional extraction solvents. Full article