Search Results (547)

Cone Penetration Tests with pore pressure measurements (CPTu) are widely used in geotechnical site investigations due to their high-resolution profiling capabilities. However, traditional interpretation methods—such as the Soil Behavior Type Index ($I_c$)—often fail to capture the internal heterogeneity typical of mining tailings deposits. This study presents a machine learning-based approach to enhance stratigraphic interpretation from CPTu data. Four unsupervised clustering algorithms—k-means, DBSCAN, MeanShift, and Affinity Propagation—were evaluated using a dataset of 12 CPTu soundings collected over a 19-year period from an iron tailings dam in Brazil. Clustering performance was assessed through visual inspection, stratigraphic consistency, and comparison with $I_c$-based profiles. k-means and MeanShift produced the most consistent stratigraphic segmentation, clearly delineating depositional layers, consolidated zones, and transitions linked to dam raising. In contrast, DBSCAN and Affinity Propagation either over-fragmented or failed to identify meaningful structures. The results demonstrate that clustering methods can reveal behavioral trends not detected by $I_c$ alone, offering a complementary perspective for understanding depositional and mechanical evolution in tailings. Integrating clustering outputs with conventional geotechnical indices improves the interpretability of CPTu profiles, supporting more informed geomechanical modeling, dam monitoring, and design. The approach provides a replicable methodology for data-rich environments with high spatial and temporal variability. Full article

Previous studies have extensively applied the generalized consolidation theory, which incorporates a two-stress state variable framework, to predict the volumetric behavior of unsaturated expansive soils under varying mechanical stress and matric suction. A key requirement for this approach is a constitutive surface that links the soil void ratio to both net stress and matric suction. A large number of fitting parameters are typically needed to accurately fit a two-variable void ratio surface equation to laboratory test data. In this study, a single-stress state variable framework was adopted to describe the void ratio as a function of effective stress for unsaturated soils. The proposed approach was applied to fit void ratio–effective stress constitutive curves to laboratory test data for two different expansive clays. Additionally, a finite element model coupling variably saturated flow and stress–strain analysis was developed to simulate the volume change behavior of expansive clay subjected to moisture fluctuations. The model utilizes suction stress to compute the effective stress field and incorporates the dependency of soil modulus on volumetric water content based on the proposed void ratio–effective stress relationship. The developed numerical model was validated against a benchmark problem in which a layer of Regina expansive clay was subjected to a constant infiltration rate. The results demonstrate the effectiveness of the proposed model in simulating expansive soil deformations under varying moisture conditions over time. Full article

The study on soil consolidation and settlement is of great importance in geotechnical engineering practice. Nowadays, physics-informed neural networks (PINN) are becoming more and more popular in solving geotechnical engineering problems thanks to their meshless, physically constrained, and data-driven nature. Although there have been some successful applications in one-dimensional (1D) consolidation problems in saturated soils, the ability and stability to deal with more complex boundary conditions remain to be tested. In this paper, the effects of activation function and random state on the PINN are investigated for solving two 1D consolidation problems in saturated soils, and the proposed method for inverse modeling of the two 1D consolidation problems. The results show that PINN with layer-wise locally adaptive activation functions improves the convergence speed and prediction accuracy of the PINN for solving the 1D nonlinear soil consolidation problems, and at the same time the robustness of the model to random states. Moreover, the proposed method still converges faster in the inverse modeling of 1D consolidation problems. Full article

This review article focuses on the long-term durability challenges associated with bamboo fiber-reinforced polymer composites when subjected to various environmental aging conditions such as water immersion, hygrothermal fluctuations, ultraviolet (UV) radiation, soil burial, and refrigerated storage. The primary issue addressed is the degradation of mechanical and structural performance of bamboo fiber-reinforced polymer composites due to moisture absorption, fiber swelling, and fiber–matrix interface deterioration. To mitigate these aging effects, the study evaluates and compares multiple strategies, including chemical and physical fiber surface treatments, filler additions, and fiber hybridization, which aim to enhance moisture resistance and mechanical stability. These composites are relevant in automotive interiors, construction panels, building insulation, and consumer goods due to their eco-friendly nature and potential to replace conventional synthetic composites. This review is necessary to consolidate current knowledge, identify effective enhancement approaches, and guide the development of environmentally resilient bamboo fiber-reinforced polymer composites for real-world applications. Full article

Expansive soils, characterized by the presence of surface and subsurface cracks, over-consolidation, and swell-shrink properties, present significant challenges to slope stability in geotechnical engineering. Despite extensive research, preventing geohazards associated with expansive soils remains unresolved. This study investigates shallow sliding failures in slopes of highly expansive soils induced by rainfall, using model tests to explore deformation and mechanical behavior under cyclic wetting and drying conditions, focusing on the interaction between soil properties and environmental factors. Model tests were conducted in a wedge-shaped box filled with Nanyang expansive clay from Henan, China, which is classified as high-plasticity clay (CH) according to the Unified Soil Classification System (USCS). The soil was compacted in four layers to maintain a 1:2 slope ratio (i.e., 1 vertical to 2 horizontal), which reflects typical expansive soil slope configurations observed in the field. Monitoring devices, including moisture sensors, pressure transducers, and displacement sensors, recorded changes in soil moisture, stress, and deformation. A static treatment phase allowed natural crack development to simulate real-world conditions. Key findings revealed that shear failure propagated along pre-existing cracks and weak structural discontinuities, supporting the progressive failure theory in shallow sliding. Cracks significantly influenced water infiltration, creating localized stress concentrations and deformation. Atmospheric conditions and wet-dry cycles were crucial, as increased moisture content reduced soil suction and weakened the slope’s strength. These results enhance understanding of expansive soil slope failure mechanisms and provide a theoretical foundation for developing improved stabilization techniques. Full article

To address the engineering challenges associated with Guilin red clay, such as its potentially low strength and unfavorable mechanical behavior, this study investigated the effectiveness of lignin and lime as modifiers. Consolidation undrained triaxial tests and scanning electron microscopy (SEM) were employed to evaluate the strength characteristics and microstructural changes in modified clay specimens with varying dosages. The results demonstrate distinct strengthening mechanisms: Lignin exhibits an optimal dosage (6%), significantly increasing cohesion and internal friction angle through physical reinforcement (“soil fiber” formation), but higher dosages (8%) lead to particle separation and strength reduction. In contrast, lime provides continuous and substantial strength enhancement with increasing dosage (up to 8%), primarily through chemical reactions producing cementitious compounds (e.g., C-S-H, C-A-H) that densify the structure. Consequently, lime-modified clay shows significantly higher cohesion and internal friction angle compared to lignin-modified clay at equivalent or higher dosages, with corresponding stress–strain curves shifting from enhanced (strain-hardening) to softening behavior. These findings provide practical insights into red clay improvement in geotechnical engineering applications. Full article

In order to accurately analyze the liquefaction and the reinforcement effect of saturated silty and sandy soils treated by dynamic compaction, a hydro-mechanically coupled explicit analysis method was proposed. The method, in combination with the cap model, was carried out using the Abaqus finite element software. Then, parametric analysis was carried out by means of the development and dissipation of excess pore water pressure, effective soil stress and the relative reinforcement degree. And the effects of the drop energy, tamper radius and soil permeability on the liquefaction zone and soil improvement of saturated soil were examined. The results demonstrated that the liquefaction zone and the effective reinforcement were determined by the drop energy rather than the permeability or tamper radius. A 2.5-times increase in drop energy can increase the maximum liquefaction depth by 1.1 m (4.6 m to 5.7 m) and the effective reinforcement depth (I_r ≥ 0.08) by 0.6 m (1.2 m to 1.8 m). It is recommended that the reinforcement effect should be improved by a lower drop energy with a low drop height and a heavy tamper in actual projects. It should also be noted that a smaller tamper radius was conducive to local soil improvement but also generated higher localized excess pore water pressures. Soil permeability critically controls liquefaction potential and excess pore water pressure dissipation. Low permeability soils experienced significant liquefaction depths and slower consolidation, whereas high permeability gravels (k = 10⁻² m/s) showed minimal liquefaction and great improvements in depth. To diminish the effect of the underground water, the gravel cushions should be used to drain pore water out before dynamic compaction. Full article

As is already known, some currently stable landslides may have been activated in the past along a pre-existing sliding surface and reached the residual strength there, as a consequence of high-cumulative displacements. After a fairly long period of quiescence, these landslides can reactivate due to a temporary increase in destabilising forces capable of mobilising the residual strength along the same sliding surface again. Some recent studies have suggested that, under certain conditions, the strength mobilised upon reactivation may slightly exceed the residual value and then decay towards the latter as the displacement progresses. Regarding this matter, many previous studies have hypothesised that some geotechnical variables could affect the recovered strength more significantly: the length of the ageing time, the vertical stress, the stress history, and the speed with which the reactivation occurs. The aim of this research is to confirm whether such recovery of strength upon reactivation is possible and which geotechnical parameters have the greatest influence on the process. To this end, laboratory tests were carried out with the Bromhead ring shear apparatus on normally consolidated saturated samples of both natural soils and clays provided by industry (bentonite and kaolin). The coupling effect of the ageing time, the vertical stress, and the reactivation speed on the mobilised strength upon reactivation were investigated, starting from a pre-existing residual state of these samples. Within the limits of this research, the results seem to confirm that all three geotechnical variables are influential, with a greater impact on the reactivation speed and, subordinately, on the ageing time for long quiescence periods. Therefore, it is concluded that a quiescent landslide could show a reactivated strength slightly higher than the residual value if the destabilising action could arise with a certain rapidity. Conversely, if the destabilising action occurs very slowly, the mobilised strength could correspond to the residual value. The experimental results of this research may find some application in the design of strengthening works for a stable quiescent landslide that could experience a fairly rapid increase in destabilising actions, such as in the case of seismic stress, morphological modification of the slope, or a rising water table. Full article

The mechanical characteristics of soil–rock mixtures (S-RMs) are essential for ensuring geotechnical engineering stability and are significantly influenced by the microstructure’s contact network configuration. Due to the irregularity of particle shapes and the variability in particle grading with S-RMs, their macro-mechanical characteristics and mesoscopic contact skeleton distribution exhibit increased complexity. To further elucidate the macro-mesoscopic mechanical behavior of S-RMs, this study employed the DEM to develop a model incorporating irregular specimens representing various states, based on CT scan outlines, and applied flexible boundary conditions. A main skeleton system of contact force chains is an effective methodology for characterizing the dominant structural features that govern the mechanical behavior of soil–rock mixture specimens. The results demonstrate that the strength of S-RMs was significantly influenced by gravel content and consolidation state; however, the relationship is not merely linear but rather intricately associated with the strength and distinctiveness of the contact force chain skeleton. In the critical state, the mechanical behavior of S-RMs was predominantly governed by the characteristics of the principal contact force skeleton: the contact force skeleton formed by gravel–gravel, despite having fewer contact forces, exhibits strong contact characteristics and an exceptionally high-density distribution of weak contacts, conferring the highest shear strength to the specimens. Conversely, the principal skeleton formed through gravel–sand exhibits contact characteristics that are less distinct compared to those associated with strong contacts. Simultaneously, the probability density distribution of weak contacts diminishes, resulting in reduced shear strength. The contact skeleton dominated by sand–sand contact forces displays similar micro-mechanical characteristics yet possesses the weakest macroscopic behavior strength. Consequently, the concept of the main skeleton of contact force chains utilized in this study presents a novel research approach for elucidating the macro- and micro-mechanical characteristics of multiphase media. Full article

To investigate the slope instability caused by differential frost heaving mechanisms from the slope crest to the toe during frost heave processes, this study takes a typical silty clay slope in Xinjiang, China, as the research object. Through indoor triaxial consolidated undrained shear tests, eight sets of natural and frost-heaved specimens were prepared under confining pressure conditions ranging from 100 to 400 kPa. The geotechnical parameters of the soil in both natural and frost-heaved states were obtained, and a spatiotemporal thermo-hydro-mechanical coupled numerical model was established to reveal the dynamic evolution law of anchor rod axial forces and the frost heave response mechanism between the frame and slope soil. The analytical results indicate that (1) the frost heave process is influenced by slope boundaries, resulting in distinct spatial variations in the temperature field response across the slope surface—namely pronounced responses at the crest and toe but a weaker response in the mid-slope. (2) Under the coupled drive of the water potential gradient and gravitational potential gradient, the ice content in the toe area increases significantly, and the horizontal frost heave force exhibits exponential growth, reaching its peak value of 92 kPa at the toe in February. (3) During soil freezing, the reverse stress field generated by soil arching shows consistent temporal variation trends with the temperature field. Along the height of the soil arch, the intensity of the reverse frost heave force field displays a nonlinear distribution characteristic of initial strengthening followed by attenuation. (4) By analyzing the changes in anchor rod axial forces during frost heaving, it was found that axial forces during the frost heave period are approximately 1.3 times those under natural conditions, confirming the frost heave period as the most critical condition for frame anchor design. Furthermore, through comparative analysis with 12 months of on-site anchor rod axial force monitoring data, the reliability and accuracy of the numerical simulation model were validated. These research outcomes provide a theoretical basis for the design of frame anchor support systems in seasonally frozen regions. Full article

Accurate settlement prediction for high-speed railway (HSR) soft foundations remains challenging due to the irregular and dynamic nature of real-world monitoring data, often represented as non-equidistant and non-stationary time series (NENSTS). Existing empirical models lack clear applicability criteria under such conditions, resulting in subjective model selection. This study introduces a Monte Carlo-based evaluation framework that integrates data-driven simulation with geotechnical principles, embedding the concept of symmetry across both modeling and assessment stages. Equivalent permeability coefficients (EPCs) are used to normalize soil consolidation behavior, enabling the generation of a large, statistically robust dataset. Four empirical settlement prediction models—Hyperbolic, Exponential, Asaoka, and Hoshino—are systematically analyzed for sensitivity to temporal features and resistance to stochastic noise. A symmetry-aware comprehensive evaluation index (CEI), constructed via a robust entropy weight method (REWM), balances multiple performance metrics to ensure objective comparison. Results reveal that while settlement behavior evolves asymmetrically with respect to EPCs over time, a symmetrical structure emerges in model suitability across distinct EPC intervals: the Asaoka method performs best under low-permeability conditions (EPC ≤ 0.03 m/d), Hoshino excels in intermediate ranges (0.03 < EPC ≤ 0.7 m/d), and the Exponential model dominates in highly permeable soils (EPC > 0.7 m/d). This framework not only quantifies model robustness under complex data conditions but also formalizes the notion of symmetrical applicability, offering a structured path toward intelligent, adaptive settlement prediction in HSR subgrade engineering. Full article

The precise prediction of soil settlement under applied loads is of paramount importance in the field of geotechnical engineering. Conventional analytical approaches often lack the capacity to accurately represent the rate-dependent deformations exhibited by soft soils. Creep affects the integrity of geotechnical structures and can lead to loss of serviceability or even system failure. Over time, they deform, the soil structure can be weakened, and consequently, the risk of collapse increases. Despite extensive research, regarding the creep characteristics of soft soils, the prediction of creep deformation remains a substantial challenge. This study explores soil consolidation settlement by employing three different material models: the Soft Soil Creep (SSC) model implemented in PLAXIS 2D, alongside two user-defined elasto-viscoplastic models, specifically Creep-SCLAY1S and the non-associated creep model for Structured Anisotropic Clay (n-SAC). Through the simulation of laboratory experiments and the Lilla Mellösa test embankment situated in Sweden, the investigation evaluates the strengths and weaknesses of these models. The results demonstrate that the predictions produced by the SSC, n-SAC, and Creep-SCLAY1S models are in close correspondence with the field observations, in contrast to the more simplistic elastoplastic model. The n-SAC and Creep-SCLAY1S models adeptly represent the stress–strain response in CRS test simulations; however, they tend to over-predict horizontal deformations in field assessments. Further investigation is advisable to enhance the ease of use and relevance of these sophisticated models. Full article

The rapid increase in population and the corresponding increase in developments have necessitated the stabilization of areas with poor soil conditions. Due to consolidation settlement, the soft grounds available are deemed unsuitable for such structures. This paper presents the use of cement additives to build sand–cement columns in saturated clayey soils. The approach significantly reduces consolidation settlement and increases the bearing capacity, providing a viable solution to foundation problems. Consolidation tests were conducted on saturated clay specimens and sand–cement columns arranged in various patterns. A 5% cement content by the dry weight of the sand was used in building sand–cement columns. The results showed that the consolidation settlement rate was high due to the extra drainage formed by the widened pores in the sand–cement columns. The extra drainage caused more water to leave the specimen in a given time. However, after full contact between the loading platen and sand–cement columns, the rate of consolidation settlement decreased. At this stage, sand–cement participated in carrying the load. Additionally, the effect of vertical drainage on speeding up consolidation at higher stress levels was minimal, as the widened pores in the sand–cement columns began to close. Full article

Monopile foundation is an important foundation form for offshore wind turbines, and the stability of the seabed around it is affected by the combined effects of wave and pile vibration. Based on the Biot consolidation theory and elastoplastic constitutive model, a multi-physical field coupling model of wave–vibration–seabed–monopile is constructed, and the dynamic characteristics of seabed pore pressure around the monopile under the joint action of wave–vibration are systematically investigated, and the influences of waves, vibrations, and seabed parameters on the distribution of pore pressure amplitude are analysed in depth. The results show that the increase in wave incident energy will increase the seabed wave pressure, and the suction and pressure generated by pile vibration will change the soil force state; the coupling of waves and vibrations results in pile displacement difference, causing the seabed pore pressure dissipation depth dissimilarity, and the peak relative amplitude of pore pressure and the peak of vibration displacement are in a linear relationship; the wave parameters and seabed characteristics have a significant effect on the change in pore pressure amplitude distribution. Full article

Because the loess widely used in the channel water conservancy projects in the Loess Plateau has a loose structure, low mechanical strength, and is prone to collapse when immersed in water, its comprehensive properties, such as structural strength and water resistance, must be greatly improved. Based on our previous work on the modification of Aga soil in Tibet, China, this study added hydrophobic n-dodecyltrimethoxysilane (WD10) to water glass solution (the main components are potassium silicate (K₂SiO₃) and silicic acid (H₂SiO₃) gel, referred to as PS) to obtain a composite coating PS-WD10, which was sprayed on the surface of loess blocks to achieve a full consolidation effect. We not only systematically investigated the morphology, chemical composition, and consolidation mechanism of the composite coating but also conducted in-depth and detailed research on its application performance such as friction resistance (structural strength), hydrophobicity, resistance to pure water and salt water immersion, and resistance to freeze–thaw cycles. The results showed that the PS-WD10 composite coating had better consolidation performance for loess blocks than the single coating of PS solution and WD10. For the loess block samples coated with the composite coatings, after 50 friction cycles, the weight loss rate was less than 15 wt%, and the water contact angle was above 120°. The main reason is that the good permeability of the PS solution and the excellent hydrophobicity of WD10 produce a good synergistic effect. The loess blocks coated with this composite coating are expected to replace traditional functional materials for water conservancy projects, such as cement and lime, in silt dam water conservancy projects, and also have better environmental protection and sustainability. Full article