Search Results (272)

Biosensors based on electrolyte-gated organic field-effect transistors (EGOFETs) have attracted considerable attention due to their advantages, including low cost, inherent signal amplification, and low-voltage operation. A critical step influencing sensing performance is the integration of specific receptors onto the device surface. Among various strategies, the covalent immobilization of biorecognition elements onto gold surfaces via thiol chemistry is one of the most widely used approaches. In this study, we report the optimization of a mixed self-assembled monolayer (SAM) composed of 11-mercaptoundecanoic acid (11-MUA) and 3-mercaptopropionic acid (3-MPA) for label-free detection of human IgG using EGOFETs. The quality of the SAM was systematically modulated by varying the total concentration from 10 to 400 mM and characterized using X-ray Photoelectron Spectroscopy (XPS), Electrochemical Impedance Spectroscopy (EIS), Cyclic Voltammetry (CV), and Atomic Force Microscopy (AFM). The results revealed that a concentration of 50 mM yielded a densely packed and well-ordered monolayer. After covalent immobilization of anti-IgG antibodies via 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride/N-hydroxysuccinimide (EDC/NHS) chemistry and subsequent blocking with ethanolamine and bovine serum albumin (BSA), the functionalized gate electrodes were integrated into poly(3-hexylthiophene) (P3HT)-based EGOFETs. Electrical measurements demonstrated that EGOFET biosensors functionalized with the 50 mM SAM achieved optimal sensing performance. The devices exhibited a highly linear response (R² = 0.998) over a wide concentration range from 1 fM to 10 nM, with a LOD of 2.82 fM, and showed excellent selectivity against non-target immunoglobulins A and M (IgA and IgM). This SAM concentration optimization strategy provides a versatile approach for engineering high-performance EGOFET biosensors, with potential applicability to a broad range of disease biomarkers. Full article

This study addresses the thermodynamic aspects of galactose oxidase (GAOx) adsorption and redox behavior on gold electrodes modified with self-assembled monolayers (SAMs) derived from thiocarboxylic acids, namely N-acetyl-L-cysteine (NAC), mercaptosuccinic acid (MSA), mercaptoacetic acid (MAA), and L-cysteine (Cys). The electrochemical response of GAOx immobilized on these SAM-modified surfaces was analyzed to extract key thermodynamic parameters governing enzyme–electrode interactions, including the formal redox potential (E°), surface excess (Γ), potential of zero charge (E_zc), adsorption free energy (∆G_add), differential capacitance (C_dl), and surface tension (γ). The results demonstrate that the nature of the terminal functional group of the SAM significantly influences the thermodynamic stabilization of GAOx at the gold interface. Shifts in the redox potential are attributed to specific coordination and electrostatic interactions between the SAM functional groups and the GAOx metal center, leading to distinct interfacial energy landscapes. Overall, the SAM-modified electrodes provide a well-defined thermodynamic framework to probe enzyme orientation, interfacial charge distribution, and stabilization of the redox-active state of GAOx during direct electron transfer. These results offer guidelines based on thermodynamic and kinetic principles for customizing enzyme–electrode interfaces, which can enhance the efficiency, stability, and consistency of third-generation electrochemical biosensors. Full article

The interface between synthetic materials and biological systems is a critical determinant of performance in medical devices and biosensors. This review examines the evolution of biointerface science through the lens of self-assembled monolayers (SAMs) of thiols on gold, a model system that offers atomic-level control over surface chemistry. We trace the field from the foundational structural characterization to the establishment of empirical design rules for bio-inertness. While early theoretical models attributed protein resistance to steric repulsion forces in polymer brushes, contemporary understanding has shifted toward the “water barrier” hypothesis, which posits that tightly bound interfacial water prevents direct biomolecular contact. We highlight recent studies that extend these concepts into “realistic” crowded biological environments. Their work reveals that fouling surfaces in crowded media generate a “viscous interphase layer” (VIL) that extends tens of nanometers into solution, whereas zwitterionic surfaces maintain a robust hydration shell that prevents this accumulation. Furthermore, this hydration barrier is shown to fundamentally alter bacterial mechanics, forcing microorganisms into a reversible, tethered “hovering” state at a significant biological interaction distance (>100 nm) from the surface, effectively precluding biofilm nucleation. These insights underscore that the future of antifouling material design lies in the precise engineering of interfacial hydration structures. Full article

The structure of self-assembled monolayers (SAMs) greatly influences electrochemical interface behavior. This study systematically examines how positional isomers of aromatic diamines (ADMs) assemble on a glassy carbon (GC) electrode and how such ordering affects the attachment and performance of electrochemically reduced graphene oxide (ERGO). SAMs of ortho-, meta-, and para-phenylenediamine (o-PDA, m-PDA, and p-PDA) were fabricated on GC and characterized using atomic force microscopy (AFM) and Raman spectroscopy. Among them, GC/p-PDA exhibited the most compact and homogeneous interfacial structure. ERGO was subsequently immobilized through the free amine functionalities of the SAM, as confirmed by attenuated total reflectance–Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry (CV). Strong covalent coupling and electrostatic interactions between the positively charged ERGO and terminal amines enabled stable attachment. Under optimized conditions, the modified GC/p-PDA/ERGO electrode demonstrated exceptional electrocatalytic activity toward nitrobenzene (NBz) reduction, achieving a high sensitivity of 1410 μA mM⁻¹ cm⁻² and a low detection limit of 0.040 μM. In addition, this sensor displayed outstanding anti-interference capability, stability, and recovery in a water sample. These results establish GC/p-PDA/ERGO sensor as a robust and efficient electrocatalytically active interface for nitroaromatic pollutants detection and sustainable environmental monitoring. Full article

This study investigates the electromagnetic field enhancement and optical response of self-assembled monolayer (SAM)-coated iron nanoparticles under laser excitation, with the aim of advancing optical gas sensing technologies. Using finite element method (FEM) simulations, we model the interaction of laser beams in both the visible (400–700 nm) and infrared (1000–2500 nm) spectral ranges with SAM-coated and uncoated nanoparticles. The results reveal that SAM coatings significantly amplify localized electromagnetic fields—reaching up to ~60 V/m in the visible range—while providing stable, wavelength-independent field distributions. In contrast, uncoated nanoparticles exhibit weaker but more variable field responses. Angular dependence analysis indicates maximal field enhancement at perpendicular (90°) detection, suggesting an orientation-sensitive design consideration for optical sensors. These findings demonstrate that SAM coatings enable stable, wavelength-independent electromagnetic responses, offering a promising pathway toward miniaturized and highly sensitive laser-based optical gas sensors. Full article

Alterations in the expression of the Klotho gene have been associated with chronic kidney disease (CKD), and its potential as an early diagnostic biomarker is currently under active investigation. In this work, we report the development of a highly sensitive, label-free electrochemical DNA-based biosensor for the detection of a 100 mer DNA fragment corresponding to a partial region of Klotho mRNA. The proposed bioplatform integrates mixed self-assembled monolayers (SAMs) and gold nanoparticles for efficient DNA immobilization within a sandwich-type configuration, coupled with impedimetric detection. Different SAM architectures were evaluated by cyclic voltammetry and electrochemical impedance spectroscopy, with the binary monolayer composed of 1-hexadecanethiol (HDT) and the capture probe (CP) exhibiting the best analytical performance. The use of gold nanoparticle-modified screen-printed carbon electrodes (AuNPs–SPCEs) resulted in a 1.4-fold increase in the signal-to-noise ratio compared to screen-printed gold electrodes. Additionally, the incorporation of a blocking step using bovine serum albumin (BSA–HDT–CP–AuNPs–SPCE) enhanced the sensitivity by 1.6-fold compared to the unblocked system. The genosensor displayed a linear response in the concentration range of 3 × 10⁻¹⁰ to 7.5 × 10⁻⁸ M, achieving a detection limit of 0.09 nM. Relative standard deviations below 7.5% were obtained for different Klotho concentrations, confirming high intra-assay and intermediary precision. Selectivity assays demonstrated negligible signals for non-complementary sequences, while recovery experiments in spiked human serum samples yielded satisfactory values between 96.5% and 103.4%. Full article

Surface modification of nucleic acid-based electrochemical biosensors has been at the forefront of research since their inception. Effective modification ensures the optimization of the sensitivity, specificity, and stability of modern biosensors. Recent advances in DNA nanotechnology have enabled the development of novel electrochemical biosensor interfaces with precise assembly and high biocompatibility. In this review, we explore three strategies for enhancing biosensor performance: the integration of tetrahedral DNA nanostructures (TDNs), self-assembled monolayers (SAMs), and DNA-based hydrogels. TDNs offer well-defined geometry and controlled spatial presentation of capture probes, significantly reducing background noise and improving target accessibility. SAMs provide a robust and tunable platform for anchoring these nanostructures, enabling reproducible and chemically stable interfaces. DNA hydrogels serve as a responsive and flexible scaffold capable of signal amplification and analyte retention. These surface architectures enhance sensitivity and minimize non-specific adsorption (NSA). We discuss recent applications and experimental outcomes, highlighting how each component is driving the next generation of nucleic acid-based biosensors. Full article

Organic field-effect transistors (OFETs) have emerged as a transformative platform for high-performance sensing technologies, yet their full potential can be realized only through coordinated performance optimization. This article provides a comprehensive review of recent strategies employed in polymer OFETs to enhance key parameters, including carrier mobility (μ), threshold voltage (Vth), on/off current ratio (I_on/I_off), and operational stability. These strategies encompass both physical and chemical approaches, such as annealing, self-assembled monolayers (SAMs), modification of main and side polymer chains, dielectric-layer engineering, buffer-layer insertion, and blending or doping techniques. The development of high-performance devices requires precise integration of physical processing and chemical design, alongside the anticipation of processing compatibility during the molecular design phase. This article further highlights the limitations of focusing solely on high mobility and advocates a balanced optimization across multiple dimensions—mobility, mechanical flexibility, environmental stability, and consistent functional performance. Adopting a multi-scale optimization framework spanning molecular, film, and device levels can substantially enhance the adaptability of OFETs for emerging applications such as flexible sensing, bioelectronic interfaces, and neuromorphic computing. Full article

The aim of present study is to deposit protective coatings with various surface chemical states on AZ91D Mg alloy. Hydrothermal bioactive ceramic coatings are performed with a surface modification by the chemical bonding of self-assembled monolayers (SAM). The electrochemical corrosion behaviors of various surface-coated AZ91D alloy within DMEM cell culture medium related to their surface chemical states are evaluated through microstructure observations, XPS surface chemical bonding analysis, static contact angles measurements, potentiodynamic polarization curves, and immersion tests. XRD and high resolution XPS of F 1s analysis results show that the hydrothermal FHA coating with a phase composition of Ca₁₀(PO₄)₆(OH)F can be effectively and uniformly deposited on the AZ91D alloy. FHA-coated AZ91D displays better anti-corrosion performances and lower degradation rates than those of uncoated AZ91D alloy in the DMEM solution. Through the high resolution XPS analysis of O 1s and P 2p spectra, it is demonstrated that 1-butylphosphonic acid (BP), 1 octylphosphonic acid (OP), and dodecylphosphonic acid (DP) molecules can be effectively bonded on the FHA surface by a covalent bond to form SAM. BP/OP/DP-SAM specimens display increased static contact angles to show a hydrophobic surface. It demonstrates that the SAM surface treatment can further enhance the corrosion resistance of FHA-coated AZ91D in the DMEM solution. After 2–16 days in vitro immersion tests in the DMEM, the surface SAM-bonded hydrophobic BP/OP/DP-SAM layers can effectively inhibit and reduce the penetration of DMEM into FHA coating. Long alkyl chains of the dodecylphosphonic acid (DP) SAM represents superior enhancing effects on the reduction of corrosion properties and weight loss. Full article

The formation and growth processes of octaneselenolate (C8Se) self-assembled monolayers (SAMs) on Au(111) from dioctyl diselenides were investigated by scanning tunneling microscopy (STM) as a function of vapor deposition time at 363 K. STM observations revealed unique surface features of the C8Se SAMs on Au(111) prepared at 363 K for 1 h, consisting of various types of narrow, bright molecular rows and broad, bright molecular rows with three-directional orientations. After increasing the deposition time from 1 and 6 h, interestingly, the structural quality of C8Se SAMs is greatly enhanced, showing the formation of tri-directional highly ordered domains with distinct domain boundaries on an entire Au(111) surface. The observed ordered phase can be described by a (2 × 2√7)rect packing structure with an arial density of 28.9 Ų/molecule. C8Se SAMs at 363 K for 24 h consisted of long-range, highly ordered domains and large, disordered domains. The ordered phase can be described by a (√3 × √23)rect packing structure with an arial density of 23.3 Ų/molecule, which is denser than that of C8Se SAMs formed by vapor deposition at 363 K and for 6 h. This study clearly demonstrates that vapor deposition is a highly effective method for preparing highly ordered alkyl selenolate SAMs on Au(111). Furthermore, molecular-scale STM results provide new insights into the formation and growth processes of alkyl selenolate SAMs on Au(111) formed by vapor deposition of dialkyl diselenides at high temperatures. Full article

Within recent years, the interest in tools to investigate carbohydrate-protein (CPI) and carbohydrate-carbohydrate interactions (CCI) has increased significantly. For the investigation of CPI and CCI, several techniques employing different linking methods are available. For mimicking the glycocalyx self-assembled monolayer (SAM) formation of carbohydrate derivatives on gold nanoparticles is most appropriate. In contrast to methods for glyco-SAM formation used previously to analyze CPI/CCI, the novel approach allows for a facile and rapid synthesis to link spacers and carbohydrate derivatives and enhances the binding event by controlling the amount and orientation of ligand. For immobilization on biorepulsive aminooxy functionalized gold nanoparticles by oxime coupling, diverse aldehyde-functionalized glycan structures of mono-, di-, and complex trisaccharides were synthesized, employing several facile steps including olefin metathesis. Effective immobilization and first binding studies are presented for the lectin concanavalin A. This novel and advantageous immobilization method is presently employed in various biomimetic studies of carbohydrates and carbohydrate-based array development for diagnostics and screening. Full article

With the increase in contamination by microbial agents (bacteria, viruses, etc.) in the fields of agri-food, healthcare, and environment, it is necessary to detect and quantify these biological elements present in complex fluids in a short time with high selectivity, high sensitivity, and, if possible, moderate cost. Acoustic wave biosensors, based on immuno-detection, appear to meet a certain number of these criteria. In this context, we are developing a generic antibody-based biointerface that can detect a wide range of pathogenic bacterial agents using a specific bioreceptor. Based on the silane–oxide chemistry, the process is transferable to any kind of surface that can be either oxidized in surface or activated with O₂-plasma, for instance. For this proof of concept, we have chosen to develop our biointerface on titanium and lithium niobate surfaces. The development of the biointerface consists of grafting antibodies via a self-assembled monolayer (SAM) composed of an aminopropyltriethoxysilane (APTES) and a linker (phenylene diisothiocyanate, PDITC). Two functionalization routes were tested for grafting APTES: in anhydrous toluene followed by a heating step at 110 °C or in chloroform at room temperature. The results obtained on titanium show comparable grafting efficiency between these two routes, allowing us to consider the transposition of the route at room temperature on lithium niobate. The latest route was chosen for fragile materials that do not require the heating steps necessary when using toluene for grafting aminopropyltriethoxysilane. Different surface characterization techniques were used, such as IR spectroscopy (FTIR-ATR), X-ray photoelectron spectroscopy (XPS), and contact angle (WCA), to verify the successful grafting of each layer. Biodetection experiments in static conditions were also carried out to demonstrate the specificity of pathogenic detection, testing an ideal medium with solely bacteria, with no other food sampling nutrients. This paper demonstrates the successful elaboration of a biointerface using APTES as the first anchoring layer, with chloroform as a mild solvent. The process is easily transferable to any kind of fragile surface. Moreover, following anti-L. monocytogenes antibodies, our biointerface shows a specificity of capture in static mode (at a concentration of 10⁷ CFU/mL for an incubation time of 4 h at 37 °C) of up to 98% compared to a species negative control (E. coli) and up to 85% in terms of strain specificity (L. innocua). Full article

Tumor Necrosis Factor-alpha (TNF-α) is a pro-inflammatory cytokine strongly associated with the early onset and progression of heart failure (HF). In this study, we present the design and fabrication of a label-free, fluorescence-based biosensor for the detection of TNF-α cytokines. The biosensor is constructed using microcontact printing (μCP) to pattern Triethoxysilylundecanal (TESUD) on oxygen plasma-activated polydimethylsiloxane (PDMS) substrates, forming self-assembled monolayers (SAMs) of microstructures. TNF-α antibodies are then covalently immobilized via imine coupling. Detection of TNF-α cytokines at 50 µg/mL was achieved via an optical “sandwich” immunoassay with rhodamine-labeled secondary antibodies, enabling visualization by fluorescence microscopy. Surface wettability analysis confirmed successful stepwise functionalization, while imaging revealed well-defined microstructures and specific immune binding of TNF-α. This platform demonstrates a proof-of-concept and offers a non-invasive, sensitive, and cost-effective alternative for the early detection of TNF-α in biological fluids, with potential applications in HF monitoring. Full article

Inverted (p-i-n) CsPbI_xBr_3−x (x = 0~3) perovskite solar cells (PSCs) are of growing interest due to their excellent thermal stability and optoelectronic performance. However, they suffer from severe energy level mismatch and significant interfacial energy losses at the bottom hole transport layers (HTLs). Herein, we propose a strategy to simultaneously enhance the crystallinity of CsPbI_2.85Br_0.15 and facilitate hole extraction at the HTL/CsPbI_2.85Br_0.15 interface by incorporating semiconducting single-walled carbon nanotubes (SWCNTs) onto [2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl] phosphonic acid (MeO-2PACz) HTL. The unique electrical properties of SWCNTs enable the MeO-2PACz/SWCNT HTL to achieve high conductivity, optimal energy level alignment, and an adaptable surface. Consequently, the defect density is reduced, hole extraction is accelerated, and interfacial charge recombination is effectively suppressed. As a result, these synergistic benefits boost the power conversion efficiency (PCE) from 15.74% to 18.78%. Moreover, unencapsulated devices retained 92.35% of their initial PCE after 150 h of storage in ambient air and 89.03% after accelerated aging at 85 °C for 10 h. These findings highlight the strong potential of SWCNTs as an effective interlayer for inverted CsPbI_2.85Br_0.15 PSCs and provide a promising strategy for designing high-performance HTLs by integrating SWCNTs with self-assembled monolayers (SAMs). Full article

The human Tau protein stands for one of the most conspicuous and crucial hallmarks of Alzheimer’s disease (AD) diagnosis, along with other tauopathies. However, the assay for direct detection of tiny Tau protein concentrations in human samples continues to pose a significant challenge for the early diagnosis of AD. Thus, an amplification-based strategy is required. In this proposed work, we established an impedimetric immunosensor to detect human Tau-441 protein in PBS buffer using a sandwich approach, wherein we employed two distinct monoclonal antibodies (HT7 and BT2) that specifically recognize the amino acids 159–198 of the target protein. Through this strategy, we were able to detect as low as 0.08 pg/mL. These findings were attributed to the use of a biotinylated antibody (BT2)-streptavidin complex, which facilitated the amplification of the normalized signal, resulting in a lower limit of detection in comparison to the directly based immunosensors. Subsequently, we investigated the designed immunosensor to assess the assay’s selectivity in the presence of different off-targets, and no cross-interaction was recorded. The outcomes of our study provide valuable new insights into the application of sandwich-based assay as a highly sensitive and selective immunosensor for the detection of small protein. Full article