Search Results (886)

With rising global temperatures and increasing sustainability demands, the need for advanced pavement solutions has never been greater. This study breaks new ground by integrating phase change materials (PCMs), including paraffin-based wax (Rubitherm RT55), hydrated salt (Climator Salt S10), and fatty acid (lauric acid), as binder modifiers within warm mix asphalt (WMA) mixtures. Moving beyond the traditional focus on binder-only modifications, this research utilizes recycled cigarette filters (CFs) as a dual-purpose fiber additive, directly reinforcing the asphalt mixture while simultaneously transforming a major urban waste stream into valuable infrastructure. The performance of the developed WMA mixture has been evaluated in terms of stiffness behavior using an Indirect Tensile Strength Modulus (ITSM) test, permanent deformation using a static creep strain test, and rutting resistance using the Hamburg wheel-track test. Laboratory tests demonstrated that the incorporation of PCMs and recycled CFs into WMA mixtures led to remarkable improvements in stiffness, deformation resistance, and rutting performance. Modified mixes consistently outperformed the control, achieving up to 15% higher stiffness after 7 days of curing, 36% lower creep strain after 4000 s, and 64% reduction in rut depth at 20,000 passes. Cost–benefit analysis and service life prediction show that, despite costing USD 0.71 more per square meter with 5 cm thickness, the modified WMA mixture delivers much greater durability and rutting resistance, extending service life to 19–29 years compared to 10–15 years for the control. This highlights the value of these modifications for durable, sustainable pavements. Full article

Separating azeotropes is an important, difficult, and expensive task, in particular for the 2-propanol–water mixture. The literature on the problem is rich in modeling studies but often lacking even the simplest experimental confirmation. In this paper, extractive distillation, liquid–liquid equilibrium-based extraction, and salting-out were experimentally tested for the desired separation. Among the four tested extractive distillation entrainers, none was able—in the investigated experimental setup—to push the system over the azeotropic composition threshold. Four novel hydrophobic deep eutectic extraction media were tested for the desired separation, and those based on menthol or thymol with decanoic acid were found most promising. Among 16 tested salting-out agents, 5 of them produced two-liquid phases, and only 4 hydrophilic inorganic salts promoted 2-propanol separation, with sodium carbonate being the most promising candidate. The purity of the products was tested with FTIR and ¹H-NMR. The experimental findings were compared with COSMO-RS model predictions, with moderate success. Full article

In sorption cooling systems, an important stage of the thermodynamic cycle is the separation of the refrigerant fluid from the absorbent mixture. This process is called “regeneration” or “desorption,” and it is similar to thermal desalination, where water is separated from an aqueous saline solution. However, since sorption systems utilize high salt concentration solutions, conventional desalination techniques such as reverse osmosis are not suitable. In this regard, membrane devices can enhance heat and mass transfer processes in compact sizes. In the present paper, a membrane device with an air gap membrane distillation configuration was evaluated, operating with the H₂O/LiBr + LiCl solution (with a mass ratio of 2:1, LiBr:LiCl), to assess the produced distilled water flux. Among the operating parameters analyzed (solution temperature, cooling water temperature, salt concentration, and membrane pore size), solution temperature had the highest impact on the distilled water flux, while the membrane pore size had the lowest impact. The maximum distilled water flux was 7.63 kg/h·m² with a solution temperature of 95.3 °C, a cooling water temperature of 25.1 °C, a salt concentration of 44.99% w/w, and a membrane pore size of 0.45 μm. On the other hand, the minimum distilled water flux was 0.28 kg/h·m² with a solution temperature of 80.3 °C, a cooling water temperature of 40.1 °C, a salt concentration of 50.05% w/w, and with a membrane pore size of 0.22 μm. Full article

Four novel crystalline architectures based on benzo[c]cinnolininium trifluoromethanesulonate salts, [C₁₂H₉N₂]⁺[CF₃SO₃]⁻, have been isolated as single-crystals, and their structures have been determined by X-ray diffraction analysis. The formation of the new salts results from reactions involving the dimeric hydroxo di-n-butylstannane trifluoromethanesulfonato complex [n-Bu₂Sn(OH)(H₂O)(CF₃SO₃)]₂ (1) and benzo[c]cinnoline (C₁₂H₈N₂, BCC). Organic salts I, II, III, and IV were crystallized through slow evaporation at room temperature from a mixture of toluene/dichloromethane. The cystallographic structures of I, II, and IV exhibit the presence of monoprotonated benzo[c]cinnolinium cations in interactions with a free benzo[c]cinnoline molecule through N–H···N hydrogen bonding, while for salt III, the monoprotonated cation directly interacts with the CF₃SO₃⁻ anion via an N–H···O interaction. For all four salts, aromatic π-π interactions involving rings of various components (free benzo[c]cinnoline molecule, benzo[c]cinnolinium cation, toluene molecule), combined with weak C–H···O and C–H···F interactions implying the trifluoromethanesulfonate anion, promote the solid-state self-assembly of supramolecular stacks. In parallel to the formation of benzo[c]cinnolinium based-salts, organotin(IV) 1 was converted into a distannoxane compound, ²_∞{[n-Bu₂(μ-OH)SnOSn(μ-η²-O₃SCF₃)n-Bu₂]₂[n-Bu₂(η¹-O₃SCF₃)SnOSn(μ-OH)n-Bu₂]₂} (3), which was also isolated as a single crystal and whose crystallographic structure was previously established by us. Full article

The black fig fly, Silba adipata (Diptera: Lonchaeidae), is an invasive pest recently introduced to Mexico, where it has rapidly spread across fig-producing regions. Despite its economic importance, effective monitoring strategies remain poorly studied. The present study evaluated the response of S. adipata adults to visual (color) and olfactory (attractant) cues under laboratory and field conditions in fig orchards. No significant color preferences were observed in laboratory choice tests using nine colors or in field trials using traps of four different colors. In the laboratory, traps containing 2% ammonium sulfate solution, torula yeast + borax, or Captor + borax, captured similar numbers of flies, whereas CeraTrap^® was less attractive. Traps containing 2% ammonium sulfate were more effective than 2% ammonium acetate, though attraction was comparable when ammonium acetate was diluted to 0.2% or 0.02%. In the field, torula yeast + borax and 2% ammonium sulfate mixed with fig latex outperformed the 2% ammonium sulfate solution alone, although seasonal variation influenced trap performance. A high proportion of field-captured females were sexually immature. Torula yeast + borax attracted high numbers of non-target insects and other lonchaeid species, which reduced its specificity. In contrast, traps containing fig latex mixtures showed higher selectivity, although some S. adipata adults could not be sexed due to specimen degradation. These findings highlight the value of torula yeast pellets and 2% ammonium sulfate plus fig latex for monitoring this pest, but merit validation in field studies performed over the entire crop cycle across both wet and dry seasons. Future studies should evaluate other proteins, ammonium salt combinations and fig latex volatiles in order to develop effective and selective monitoring or mass trapping tools targeted at this invasive pest. Full article

High-power lithium-ion batteries impose stringent requirements on output power. Tetramethylene sulfone (TMS), serving as a novel electrolyte additive, effectively enhances the stability of electrolytes under high-voltage conditions due to its high flash point and high dielectric constant, thereby boosting the output performance of lithium-ion batteries. In this work, we selected lithium hexafluorophosphate (LiPF₆) as the lithium salt, using a solvent carrier consisting of a mixture of ethylene carbonate (EC), dimethyl carbonate (DMC), and ethyl methyl carbonate (EMC). TMS was added as an additive to create a novel high-power electrolyte system. We prepared five electrolytes with different TMS concentrations and conducted in-depth investigations into their impacts on the performance of lithium-ion batteries. The findings indicate that the electrolytes with TMS ratios of 2 wt% and 5 wt% demonstrated good synergistic cathode–anode stability in the NCM//soft carbon system, and the electrolyte with a 5 wt% TMS ratio demonstrated the most significant improvement in the overall performance of the full battery. Full article

This study explores the feasibility of utilizing granite sawing sludge (FC) as a precursor to produce alkali-activated materials (AAMs). To enhance the reactivity of the system, metakaolin (MK) was added and binary mixtures were synthetized. A multidisciplinary approach, including mineralogical, chemical and mechanical analysis, was employed to assess the suitability of these precursors to produce AAMs. X-Ray diffraction (XRD) and Fourier-Transform Infrared spectroscopy (FT-IR) confirmed the occurred activation reaction with the consequent increase in the amorphous content. Raman spectroscopy was used to further explore the mineralogical composition of the consolidated specimens, helping in the detection of salts, whose formation is ascribed to secondary carbonatation processes. Morphological analysis (SEM-EDS) displayed relatively uniform microstructures for all specimens. Compressive strength tests revealed that MK rich samples achieved best values compared to FC rich formulations, which exhibited reduced strength resistance. This study highlights, for the first time, the benefits of incorporating Cuasso al Monte granite sawing sludges into alkali-activated binders. Results suggested that the incorporation of FC is recommended for both environmental and economic advantages. Full article

In response to the growing impact of the climate crisis, many countries are accelerating efforts to develop sustainable and carbon-free energy solutions. This has led to increasing interest in advanced energy storage and conversion technologies, particularly the development of high-temperature molten salt energy systems. Among these, chloride salt-based molten salt systems, which offer excellent thermal properties such as high thermal conductivity, low melting points, and favorable chemical stability, are emerging as strong candidates for thermal energy storage and heat-transfer applications. This study focuses on deriving key thermophysical properties essential for selecting suitable molten salt heat-transfer fluids by examining their eutectic points and thermal stability with respect to various salt compositions. Three chloride mixtures—NaCl-MgCl₂, NaCl-KCl-MgCl₂, and NaCl-KCl-ZnCl₂—were evaluated for potential use in high-temperature molten salt energy systems. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were employed to measure the melting points and thermal stability of molten salts with various compositions near their eutectic regions. Experimental results were compared with predicted eutectic points to assess the thermal performance of each salt mixture. The findings indicate that the NaCl-KCl-MgCl₂ mixture exhibits the most promising characteristics, including a low melting point below 400 °C and superior thermal stability, making it highly suitable as a heat-transfer fluid in high-temperature molten salt energy systems. In contrast, NaCl-KCl-ZnCl₂ was found unsuitable for such applications due to its high hygroscopicity and poor thermal stability. This study provides essential data for selecting optimal molten salt compositions for the efficient and reliable operation of high-temperature molten salt energy systems. Full article

In this paper, the electrochemical performance of the NiAl intermetallic immersed in the 60% NaNO₃-40% KNO₃ (wt%) eutectic mixture, also known as Solar Salt, is reported. Mass loss measurements and electrochemical tests evaluate its behavior at different temperatures (300, 400, and 500 °C). Mass loss measurements are performed over 1000 h, and electrochemical tests over 100 h. The mass loss results show that the Ni₃Al intermetallic exhibits excellent corrosion resistance under the test conditions. Electrochemical measurements confirm the excellent performance of the Ni₃Al intermetallic in molten solar salt in the test temperature range. Experimental observations show that increasing temperature decreases the corrosion resistance of the intermetallic and favors the formation of protective layers of the Al₂O₃ and NaAlO₂ types. Full article

The separation of particles smaller than 1 µm either by composition or by size is still a challenge. For the separation of SiO₂ and SnO₂, the creation of a selective separation feature and the specific adsorption of salts and surfactants were investigated. The adsorption of various salts, e.g., AlCl₃, ZnCl₂, MnCl₂ and MgCl₂ were therefore analyzed, and the necessary concentration for the charge reversal of the material was determined. It was noticed that the investigated materials differ in their isoelectric point (IEP) and therefore in their adsorption behavior because only ZnCl₂ and MgCl₂ are suitable for a charge reversal of both metal oxides. The phase transfer of the pure material at different pH values with ZnCl₂ or MgCl₂ and sodium dodecyl sulfate (SDS) revealed that the adsorption behavior of the particle has an influence on the phase transfer. As a result, the phase transfer of SiO₂ is pH dependent, whereas the phase transfer of SnO₂ operates over a wider pH range. This allowed the separation of SiO₂ and SnO₂ to be controlled by the salt and surfactant concentration as well as pH. The separation of SiO₂ and SnO₂ was investigated for various parameters such as salt and surfactant concentration, particle concentration and composition of the mixture. Also, pH 8, where a selective phase transfer for SiO₂ occurs, and pH 6, where the greatest difference between the materials exists, were also investigated. By comparing the parameters, it was found that the combination of ZnCl₂/SDS and MgCl₂/SDS enables a selective separation of the materials. Furthermore, it was also found that the concentration of SDS has a significant effect on the separation, as the formation of a bilayer structure is important for the separation, and therefore, higher SDS concentrations are required at higher particle concentrations to increase the separation efficiency. Full article

Salinity has significant impacts on crops, a problem that is exacerbated under climate change conditions. For this reason, research is focused on possible ways to mitigate the impacts by adapting cultivation methods such as administering appropriate materials or formulations to plants. Therefore, this study investigated the effects of calcium (Ca²⁺) supplementation on the growth, physiology, and chemical composition of pomegranate plants (Punica granatum L. cv. ‘Wonderful’) grown under salinity stress. Young self-rooted plants were cultivated in pots containing a sand/perlite (1:1) mixture and irrigated with Hoagland’s nutrient solution amended with NaCl (0, 60, or 120 mM) and CaCl₂·2H₂O (0 or 10 mM). Salinity significantly reduced the fresh and dry weight of aboveground tissues; photosynthetic performance; chlorophyll content; and potassium (K), calcium (Ca), and magnesium (Mg) concentrations, particularly under high NaCl levels. Sodium (Na) accumulation increased in all plant parts, while nitrogen (N), manganese (Mn), and zinc (Zn) concentrations were elevated in basal leaves. Calcium supplementation mitigated several of these adverse effects, especially under moderate salinity. It helped maintain leaf biomass, supported K⁺ retention in roots, partially improved chlorophyll concentration, and limited Na⁺ accumulation in certain tissues. However, Ca²⁺ application did not consistently reverse the negative impacts of severe salinity (120 mM NaCl), and in some cases, interactions between Ca²⁺ and other nutrients such as Mg²⁺ were antagonistic. These findings confirm the inherent salt tolerance of pomegranate and demonstrate that calcium plays a partially protective role under salinity, particularly at moderate stress levels. Further research is needed to optimize Ca²⁺ use in saline agriculture and enhance sustainable cultivation of pomegranate in salt-affected soils. Full article

The production of high-quality horticultural seedlings is essential for successful field transplantation. Nevertheless, increasing soil salinization poses a significant challenge, particularly in salt-affected regions. Watermelon seedlings were cultivated in pots with a substrate (mixture of ground blonde peat (60%), black peat (30%), and perlite (10%) with pH 5.5–6.0) within a bamboo nethouse and subjected to varying salinity levels, i.e., 2–8 dS m⁻¹ (T1, T2, T3, and T4). At the end of the experimental period (4 weeks), the growth parameters, spectral vegetation indices, and chemical parameters of the sap and leachate were evaluated. The results demonstrated that increased salinity levels reduced the biomass of watermelon seedlings. In addition, elevated salinity levels were associated with increased values of B (48%) and NBI (46%) and decreased values of G (9%) and NGI (7%) at the end of the experimental period. The effects of the salinity levels were also evident in the sap chemical parameters, with marked increases in Cl⁻, Ca²⁺, and Na⁺ concentrations (9.6, 3.1, and 4.9 times, respectively) and decreases in the N-NO₃⁻, P, and K⁺ concentrations (51, 8, and 25%, respectively). The leachate analysis reported clear increases in the values of EC and concentrations of Cl⁻, Ca²⁺, and Na⁺ at the end of the experimental period. To validate the relevance of these findings, further research under field conditions and across a range of climatic environments is warranted. Full article

Microbiological safety and quality consistency are critical challenges in the production of traditional Indian fried snacks, particularly in small-scale food enterprises. With growing export demand, maintaining strict quality control measures is essential. This study assessed the microbiological and physicochemical quality of five traditional Indian fried snacks—Kerala Murukku, Kerala Mixture, Banana Chips, Tapioca Chips, and Achappam—produced in a Food Safety Management System (FSMS)-certified facility over a four-year period (2020–2023). Products were evaluated for moisture, pH, salt content, acid value, and Total Plate Count (TPC). The number of ingredients for each product was recorded from standardized product formulation documents. TPC levels remained within acceptable limits (below 50,000 CFU/g) across all products. Among them, Kerala Mixture consistently showed the highest microbial counts (up to 4.61 log CFU/g) and Achappam the lowest, with no detectable variance (1.00 log CFU/g). Statistically significant year-wise differences (p < 0.05) were observed in all quality parameters. Kerala Mixture showed variation in salt and microbial load; Kerala Murukku varied in moisture, pH, and salt; while Tapioca Chips varied in moisture and salt. PCA identified that TPC, salt content, number of ingredients, and pH were key contributors to product variability. Cluster analysis confirmed Kerala Mixture as the most susceptible product to contamination risk. These findings provide valuable insights into the quality trends within an FSMS-certified environment and highlight the importance of strict post-processing controls. Full article

This study evaluated the effects of supplementing early-lactation Holstein cows with rumen-protected omega-3 fatty acids (calcium salts) on productive and reproductive performance. Thirty-six multiparous cows were randomly assigned to one of two treatments from 21 ± 2 days before calving to 105 ± 5 days in milk (DIM): a Control group (C) or an Omega-3-supplemented group (O-3), receiving a blend of linseed and fish oil (60:40). Both groups were fed isoenergetic diets, with ground corn as the control supplement. Total dry matter and net energy intake did not differ between treatments. A treatment-by-time interaction was observed for milk yield, with cows in the O-3 group producing more milk than controls at specific time points. Additionally, O-3 cows had higher overall protein yield and improved feed efficiency. No differences were found in body weight, BCS, glucose, insulin, IGF-1, or urea concentrations, but a tendency toward higher plasma NEFA and BHBA concentrations and lower energy balance was observed in the O-3 group. Supplementation increased plasma cholesterol and progesterone concentrations and was associated with a higher proportion of cows being pregnant at 130 DIM. These findings suggest that omega-3 supplementation may improve specific aspects of lactational performance and reproductive efficiency without compromising metabolic status. Full article

This review presents information obtained over the past 10 years on the methods to control the widespread worldwide phytopathogen Pectobacterium carotovorum subsp. carotovorum (Pcc). This bacterium is among the ten most dangerous phytopathogens; it affects a wide range of cultivated plants: vegetables, ornamental and medicinal crops, both during vegetation and during the storage of fruits. Symptoms of Pcc damage include the wilting of plants, blackening of vessels on leaves, stems and petioles. At the flowering stage, the stem core gradually wilts and, starting from the root, the stem breaks and the plant dies. Pcc is a rod-shaped, non-capsule and endospore-forming facultative anaerobic Gram-negative bacterium with peritrichous flagellation. Pcc synthesizes bacteriocins—carocins. The main virulence factors of Pcc are the synthesis of N-acyl-homoserine lactone (AHL) and plant cell wall-degrading enzymes (PCWDEs) (pectinases, polygalacturonases, cellulases, and proteases). Diagnostic methods for this phytopathogen include polymerase chain reaction (PCR), loop-mediated isothermal amplification (LAMP), multilocus genotyping of strain-specific genes and detection of unique volatile organic compounds (VOCs). The main methods to control this microorganism include the use of various chemicals (acids, phenols, esters, salts, gases), plant extracts (from grasses, shrubs, trees, and algae), antagonistic bacteria (Bacillus, Pseudomonas, Streptomyces, and lactic acid bacteria), viruses (including a mixture of bacteriophages), and nanomaterials based on metals and chitosan. Full article