Search Results (1,638)

Chromium (Cr) toxicity poses a significant challenge to agricultural productivity, human health, and food security. Biochar (BC) is a versatile amendment employed to alleviate Cr toxicity. Chromium stress impairs growth by inducing membrane damage and cellular oxidation, as well as inhibiting chlorophyll synthesis, photosynthetic efficiency, water uptake, and nutrient absorption. This review consolidates information on the mechanisms through which BC mitigates Cr stress. Biochar facilitates Cr immobilization by reduction, adsorption, precipitation, and complexation processes. It enhances growth by improving photosynthetic efficiency, water and nutrient uptake, osmolyte synthesis, and hormonal balance. Additionally, biochar promotes resilient bacterial communities that reduce Cr and enhance nutrient cycling. The effectiveness of BC is not universal and largely depends on its feedstock properties and pyrolysis temperature. This review provides insights into soil quality, plant function, and human health, which contribute to providing a comprehensive assessment of the capacity of BC to mitigate Cr toxicity. This review highlights that BC application can reduce Cr entry into the food chain, thus decreasing its health risk. This review also identifies knowledge gaps and outlines future research directions to increase the efficiency of BC in mitigating Cr toxicity. This review also offers insights into the development of eco-friendly measures to remediate Cr-polluted soils. Full article

Microplastic quantification in marine vegetated ecosystems remains analytically demanding, yet little is known about the environmental footprint of the laboratory procedures required to isolate and measure these particles. This study applies Life Cycle Assessment (LCA) to laboratory analytical workflows for microplastics quantification, focusing exclusively on sample preparation and analytical procedures rather than natural environmental absorption or fate processes, in two ecologically relevant matrices: (i) pelagic algae (Sargassum) and (ii) seagrass biomass. Using the openLCA 2.5 and the ReCiPe Midpoint (H) v1.13 methods, the analysis integrates foreground inventories of digestion, filtration, drying, and spectroscopic identification, combined with background datasets from OzLCI2019, ELCD 3.2 and USDA. Results show substantially higher impacts for the algae scenario, particularly for climate change, human toxicity, ionising radiation and particulate matter formation, largely driven by longer digestion times, increased reagent use and higher energy demand during sample pre-treatment. Conversely, the seagrass scenario exhibited lower burdens per functional unit due to reduced organic complexity and shorter laboratory processing requirements. These findings highlight the importance of matrix-specific methodological choices and the influence of background datasets on impact profiles. This study provides the first benchmark for the environmental performance of microplastic analytical workflows and underscores the need for harmonised, low-impact laboratory protocols to support sustainable monitoring of microplastic pollution in marine ecosystems. Full article

The widespread application of concrete with specific functions has become indispensable in modern technology. However, the persistent issue of electromagnetic pollution poses a serious hazard to human health, electronic equipment, and military operations. Although various conventional electromagnetic absorbing materials have been incorporated, the achievable EMW-absorption performance is still restricted, with only a narrow effective absorption bandwidth. This study investigates the application of advanced 3D-printing technology to produce concrete with enhanced EMW-absorption properties with the incorporation of SAP (super-absorbent polymers). To achieve this, concrete samples with three SAP occupying the concrete volumes (0 vol.%, 20 vol.%, and 40 vol.%) and three methods (pretreatment-addition) were examined to provide an in-depth analysis of the properties and microstructures. The study reveals superior electromagnetic absorption in concrete enhanced with SAP compared to the untreated counterpart. Specifically, samples subjected to 40 vol.% Dry Treatment SAP exhibited exceptional performance, achieving 98.77% absorption at 7.53 GHz frequency with a peak reflectance of −19.12 dB, outperforming unmodified absorbing resin concrete by 25.44%. Moreover, microscopic analysis revealed irregular void distribution within the concrete, while the 3D-printing and -mixing processes led to SAP particle fractures, forming a complex 3D structure, thereby enhancing EMW-absorption performance. Ultimately, by selecting appropriate SAP pre-treatment and mixing methods based on the specific frequency range, this study provides crucial references and practical guidance for the application of EMW-absorbing concrete in military and technological contexts. Full article

Civilisational progress contributes to an increase in the number of vehicles on the road, thereby intensifying air pollutant emissions and accelerating the degradation of the natural environment. Effective protection of urban areas against air pollution enhances safeguarding against numerous allergies and diseases resulting from unplanned and unintended absorption of harmful pollutants into the human body. Sustainable urban planning requires the collaboration of multiple scientific disciplines. In this context, measurement becomes crucial, as it reveals the spatial scale of the problem and identifies existing disparities. This study uses an integrated approach of standard measurement methods and statistical and geostatistical data analysis, identifying PM₁ fractions that are not included in EU air quality monitoring. The hypothesis explores how surface-based results correspond to point-based results from national air quality monitoring. The presented implications demonstrate similarities and differences between the studied measurement methods and the spatial distributions of PM₁₀, PM_2.5, and PM₁ dust. Full article

Rubber particles have been proven to have the advantages of improving the energy absorption effect and enhancing the friction between soil particles when used to modify the soil. The rubber-modified soil technology also provides a new solution for the pollution-free disposal of waste rubber. However, when rubber particles are used to modify collapsible loess, they cannot significantly enhance its strength. Previous studies have not systematically clarified whether combining rubber particles with different cementation mechanisms can overcome this limitation, nor compared their shear mechanical effectiveness under identical conditions. In view of this, a dual synergistic strategy is implemented by combining rubber with lime and rubber with enzyme-induced calcium carbonate precipitation (EICP). Direct shear tests and scanning electron microscopy are used to evaluate four modification approaches: rubber alone, lime alone, rubber with EICP, and rubber with lime. Accordingly, shear strength, cohesion, and internal friction angle are quantified. At a vertical normal stress of 100 kPa and above, samples modified with rubber and lime (7–9% lime and 6–8% rubber) achieve peak shear strength values of 200–203 kPa, representing an 86.4% increase compared to rubber alone. Microscopic analysis reveals that calcium silicate hydrate gel effectively anchored rubber particles, forming a composite structure with a rigid skeleton and elastic buffer. In comparison, the rubber and EICP group (10% rubber) shows a substantial increase in internal friction angle (24.25°) but only a modest improvement in cohesion (16.5%), which is due to limited continuity in the calcium carbonate bonding network. It should be noted that the performance of EICP-based modification is constrained by curing efficiency and reaction continuity, which may affect its scalability in conventional engineering applications. Overall, the combination of rubber and lime provided an optimal balance of strength, ductility, and construction efficiency. Meanwhile, the rubber and EICP method demonstrates notable advantages in environmental compatibility and long-term durability, making it suitable for ecologically sensitive applications. The results offer a framework for loess stabilization based on performance adaptation and resource recycling, supporting sustainable use of waste rubber in geotechnical engineering. Full article

Cadmium sulfide is an important II-VI semiconductor known for its valuable photocatalytic properties ascribable to its band gap energy, which allows light absorption in the visible domain. Nonetheless, the application of cadmium sulfide in wastewater organic pollutant degradation is restricted due to its high toxicity to humans, soil, and marine life. To address this issue, we developed new composite materials by depositing CdS on a bentonite support in a 1:9 mass ratio to develop a photocatalyst with lower toxicity. In the first step, bentonite was activated using an aqueous HCl solution; for the deposition of CdS powder, we proposed the trituration method and compared it with chemical precipitation and hydrothermal synthesis, using thioacetamide as a sulfide ion source. The modified bentonite underwent characterization using X-ray diffraction, scanning electron microscopy, X-ray fluorescence, UV-Vis, and FTIR spectroscopy. The photocatalytic activity was tested in the degradation of Congo red (CR), a persistent diazo dye. The efficiency of removing CR with CdS–bentonite composites depended on the deposition method of CdS, and it was higher than that of pristine CdS and of only adsorption onto acid-activated bentonite. The photocatalytic degradation mechanism was estimated by the scavenger test using ethylenediaminetetraacetic acid disodium salt, ascorbic acid, ethanol, and silver nitrate as radical scavengers. Full article

The use of flawed excavated-mass aggregates produced from crushing and screening hydraulic engineering waste in concrete projects can reduce natural resource extraction, increase waste utilization rates, and minimize environmental pollution. However, the direct application of flawed excavated-mass aggregates is limited due to their high crushing index and water absorption rate. Therefore, this paper measures the multi-dimensional physical and mechanical properties of defective aggregates. A strengthening slurry is prepared by comprehensively modifying the crystallization strength and penetration path of sodium silicate solution using various chemical reagents. The strengthening mechanism of the slurry on flawed excavated-mass aggregates is analyzed using SEM and MIP tests. Concrete tests are designed to investigate the workability and mechanical properties of flawed excavated-mass aggregate concrete. The pore structure of the ITZ (Interfacial Transition Zone) in defective aggregate concrete is analyzed through BSE (Backscattered Electron) imaging to elucidate the strengthening mechanism of secondary crystallization reactions on the ITZ. The research findings can provide technical support for repairing aggregates with defects. Full article

Heavy metals are among the most hazardous pollutants to human health and can be particularly harmful when inhaled or ingested. Therefore, the concentrations of heavy metals in fruits and vegetables grown in regions with high levels of heavy metal pollution should be carefully examined. This study investigated the variation in aluminum (Al), nickel (Ni), and zinc (Zn) concentrations by species and organ in tomatoes, peppers, eggplants, cucumbers, and corn grown near the industrial zone in Düzce, a heavily polluted city in Europe. We determined bioconcentration factors (BCFs) and translocation factors (TFs) in plant organs and assessed the health risk through the Target Hazard Quotient (THQ) and Hazard Index (HI). The results show that Al pollution in the region significantly exceeded the World Health Organization (WHO) and European Union (EU) limit values, and accumulated in all plant organs, including fruits. Furthermore, high levels of metals were translocated from the soil into the organs of peppers and tomatoes. The HI indicated a potential non-carcinogenic health risk (HI > 1) from the consumption of tomatoes, cucumbers, and peppers, primarily driven by Ni. Based on these results, it is recommended that local authorities address Al pollution in the region, avoiding the cultivation of tomatoes and peppers and instead cultivating corn and eggplant. We also observed that Zn levels were very high in the aerial parts of the plants, reaching up to 90% compared to Ni and Al. This study underscores the need to reduce Zn absorption rates, as dietary intake can pose a significant threat to human health. Full article

Water pollution poses a pressing global environmental threat, driving an urgent need for efficient, stable, and eco-friendly water treatment techniques. Semiconductor photocatalysis has emerged as a highly promising solution, utilizing solar energy to thoroughly degrade pollutants under mild conditions without secondary pollution. Among numerous photocatalysts, the graphitic carbon nitride (g-C₃N₄)/layered double hydroxides (LDHs) heterostructures represent a kind of high-performance photocatalysts that combine the integrated advantages of both components. These composites exhibit enhanced visible-light absorption, a highly efficient charge separation and transfer, and a significantly increased specific surface area that promotes the enrichment and degradation of pollutants. The synergistic interaction between g-C₃N₄ and LDHs not only mitigates their individual limitations but also creates a superior photocatalytic system with improved adsorption capacity and reaction kinetics. This review systematically summarizes recent advances in g-C₃N₄/LDHs composite photocatalysts for aquatic pollutant removal. It elaborates on the structural synergies, synthesis routes, and optimization strategies, with a particular focus on applications and mechanistic insights into the degradation of various pollutants-including organic dyes, drugs, and phenolics. Finally, the review outlines current challenges and future research directions, such as deepening mechanistic understanding, designing multifunctional systems, and advancing toward scalable implementation, providing a valuable reference for developing next-generation photocatalytic water treatment technologies. Full article

Contamination of agricultural soils with heavy metals, such as zinc (Zn), copper (Cu) and lead (Pb), is a major problem for food safety and environmental sustainability. The present study aimed to evaluate the efficiency of phytoremediation induced with Brassica juncea (Indian mustard) and ethylenediaminetetraacetic acid (EDTA) in reducing the content of heavy metals in contaminated soils. The experiment was carried out in a greenhouse, using soil polluted with Zn, Cu and Pb, to which different treatments were applied, using: the biological method (Indian mustard only), the chemical method (EDTA in three concentrations: 0.5–1.0–2.0 mmol·kg⁻¹) and the mixed method (Indian mustard and EDTA in three concentrations: 0.5–1.0–2.0 mmol·kg⁻¹). The determinations included the analysis of the residual metal content by atomic absorption spectroscopy, as well as the evaluation of the physiological parameters of the plants (biomass, chlorophyll content in leaves, humidity, height). The results of unifactorial and bifactorial ANOVA revealed highly significant differences (p < 0.001) between the treatments and the types of metals, confirming the synergistic interaction between the chelation and phytoextraction processes. The combined treatments Indian mustard and EDTA in concentrations of 1.0 mmol·kg⁻¹ and 2.0 mmol·kg⁻¹, ensured the highest decontamination efficiency, with reductions of 51.5% for Zn, 36.3% for Pb and 27.5% for Cu. In conclusion, the mixed method represents a viable, ecological and reproducible strategy for the remediation of soils contaminated with heavy metals. Full article

Chemical oxygen demand (COD) serves as a critical indicator for assessing the extent of water pollution caused by organic matter. This study proposes an integrated COD detection methodology that combines laser absorption spectroscopy with laser-induced fluorescence spectroscopy, enabling accurate measurement of COD parameters across a wide concentration range. For high-concentration COD, conventional ultraviolet absorption spectrophotometry based on the Lambert–Beer law is employed. However, since laser absorption spectrophotometry exhibits substantial errors in detecting low-concentration COD, laser-induced fluorescence spectroscopy is adopted for the precise quantification of trace-level COD. By integrating these two laser-based approaches, a spectroscopic COD detection system has been developed that simultaneously records absorbance after the laser passes through the sample and quantifies fluorescence intensity perpendicular to the beam with an image sensor, thereby achieving comprehensive COD analysis. Laboratory validation using COD standard solutions demonstrated relative errors below 11% across the concentration range of 2–220 mg/L. Further application to natural water samples confirmed that the integrated laser absorption–fluorescence spectroscopy approach achieves wide-range COD measurement with high sensitivity, a compact configuration, and rapid response, demonstrating strong potential for real-time online water quality monitoring. Full article

Photocatalytic processes have emerged as an efficacious strategy for the removal of organic pollutants from wastewater. In the present investigation, a BiVO₄ nanorod supported on Bi₂O₂S nanosheet catalyst (referred to as BiVO₄/Bi₂O₂S) was meticulously synthesized via a straightforward synthetic approach, aimed explicitly at the photodegradation of tetracycline (TC). The optimized BiVO₄/Bi₂O₂S composite, with a theoretical weight ratio of BiVO₄ to Bi₂O₂S at 2:1 (designated as 2BVO/BOS), demonstrated a significant improvement in tetracycline degradation efficiency, achieving up to 82.9% under visible light irradiation for 90 min. This result stands in stark contrast to the relatively low degradation rates of 42.9% and 50.7% observed for pure BiVO₄ and Bi₂O₂S, respectively. Furthermore, the apparent reaction rate of 2BVO/BOS (approximately 0.01894 min⁻¹) was 3.19-fold and 2.66-fold higher than those of BiVO₄ (0.00594 min⁻¹) and Bi₂O₂S (0.00713 min⁻¹), respectively. This significant improvement in photocatalytic efficacy can be ascribed to the composite’s superior capacity for visible light absorption, as well as its remarkable proficiency in charge carrier separation and transfer. Comprehensive experimental analyses, corroborated by extensive characterization techniques, revealed the formation of a distinctive S-scheme charge transfer mechanism at the interface between BiVO₄ and Bi₂O₂S. This mechanism effectively suppresses charge recombination and optimizes the redox potentials of the photogenerated carriers, thereby enhancing the overall photocatalytic performance. The current study underscores the remarkable potential and promising application of BiVO₄/Bi₂O₂S composite in the realm of wastewater treatment. Full article

This study investigates the dynamics of carbon flux at the water–air interface during the ecological restoration of eutrophic water bodies. A controlled simulation of the eutrophic aquatic environment was carried out. A series of experiments was established, centered on submerged aquatic plants as key agents for carbon sequestration and enhancement of carbon sink capacity, supplemented by biological manipulation techniques aimed at pollution reduction and algal control. Results show that restoration systems based on submerged plants significantly enhance carbon sequestration, whereas systems relying solely on filter-feeding fish tend to increase the carbon emission burden. The submerged plant-only treatment (HV) exhibited the highest carbon absorption capacity (−72.53 mg·m⁻²·h⁻¹), followed by submerged plant + fish + snail (HSXB) and submerged plant + fish (HSX) treatments. CH₄ emissions were initially higher in the combined biological treatments but were eventually surpassed by the control group as algal cell density increased. Carbon sink potential and CH₄ emissions were strongly correlated with algal cell density and chlorophyll a concentration. While combination treatments (HSX and HSXB) effectively suppressed algal proliferation, the submerged plant-only treatment demonstrated superior nutrient removal efficiency. The findings provide theoretical support for ecologically based management strategies that simultaneously address eutrophication control and carbon sequestration in freshwater ecosystems, contributing to both water quality improvement and climate change mitigation. Full article

The disposal of industrial waste poses a significant environmental challenge, often leading to pollution and degradation of surrounding and terrestrial ecosystems. This study investigates the sustainable valorization of such wastes through the development of one-part geopolymer mortars. Solid sodium silicate was employed as a dry alkali activator for binary blends comprising ground granulated blast-furnace slag (GGBS), clay brick powder (CBP), steel slag (SS), and fly ash (FA), with all mixtures cured under ambient conditions. The mortars were evaluated in terms of fresh properties (flow and setting time) and hardened characteristics, including compressive strength, density, water absorption, and porosity. Durability performance was assessed through mass loss, visual degradation, and compressive strength retention following exposure to acidic (H₂SO₄, HCl) and sulfate environments. Microstructural characterization using XRD, SEM, and FTIR provided insight into the mechanisms of gel formation and degradation in aggressive media. The results revealed that incorporating 5% FA into GGBS-based mortars enhanced 28-day compressive strength by 21.7% compared with the control mix. The inclusion of industrial by-products promoted the formation of C–S–H and C–(A)–S–H gels, contributing to a denser and more refined microstructure. Overall, the findings demonstrate that one-part geopolymer mortars offer a promising, eco-efficient, and durable alternative to traditional cementitious systems, while also addressing safety and handling concerns associated with liquid alkaline activators used in conventional two-part geopolymer formulations. Full article

Urban heat vulnerability is an increasing public health concern, particularly in rapidly urbanizing regions of southern France. This study aims to quantify and map the Heat Vulnerability Index (HVI) for Toulouse and to analyze its temporal trends to identify high-risk zones and influencing factors. The assessment integrates recent years’ remote sensing data of pollutant emissions, land use/land cover and land surface temperature, statistical data of climate-related mortalities, and socioeconomic and demographic factors. Following a detailed analysis of recent real-time air quality and weather data from multiple monitoring stations across the city of Toulouse, it was observed that Urban Pollution Island (UPI) and Urban Heat Island (UHI) are closely interlinked phenomena. Their combined effects can significantly elevate the annual mortality risk rate by an average of 2%, as calculated using AirQ+ particularly, in densely populated urban areas. Remote sensing data was processed using Google Earth Engine and all factors were grouped into three key categories: heat exposure, heat sensitivity, and adaptive capacity to derive HVI. Temporal HVI maps were generated and analyzed to identify recent trends, revealing a persistent increase in vulnerability across the city. Comparative results show that 2022 was the most critical summer period, especially evident in areas with limited vegetation and extensive use of heat-absorptive materials in buildings and pavements. The year 2024 indicates resiliency and adaptation although some areas remain highly vulnerable. These findings highlight the urgent need for targeted mitigation strategies to improve public health, enhance urban resilience, and promote overall human well-being. This research provides valuable insights for urban planners and municipal authorities in designing greener, more heat-resilient environments. Full article