Search Results (31)

The treatment of wastewater and the utilization of the by-products of these processes are an important part of the circular economy. The sewage sludge, a result of wastewater treatment, could be used as a material for plant nutrient supply and/or soil-improving products. The city of Nyíregyháza, Hungary, with 120,000 citizens, has a well-planned water treatment plant operated by Nyírségvíz Ltd., which, in cooperation with the Research Institute of Nyíregyháza, developed a municipal sewage sludge compost (SSC). The closed loop of sewage water treatment and the agricultural utilization of its by-product has been developed and managed. The compost product called Nyírkomposzt was planned for acidic sandy soils. Beyond the agronomic benefits, the sustainable and environmentally sound utilization of SSC reduces sewage sludge disposal. This active involvement of a water utility company demonstrates the potential of cross-sectoral cooperation in solving environmental problems. The quality of the compost fits the Hungarian legislation. To study the effects of 0, 9, 18, and 27 t ha⁻¹ doses of compost on acidic sandy soil, a long-term small plot experiment was started in 2003. The cumulative effects of the regular (every third year, last treatment before sampling in 2021) application of the SSC showed positive changes in basic soil properties, depending on the doses used. Increasing values were found in the case of pH from 4.5 to 6, plant available P₂O₅ from 240 to 690 ppm, and plant available K₂O from 180 to 200 ppm. The plant-available zinc and copper content also increased. Soil organic matter and total N content stabilized at around 0.9% and 0.08%, respectively. The grain yields of winter rye also increased in both investigated years. The yields of 18 t ha⁻¹ treatment were about two times higher compared to the control, but only in 2022 was the difference significant. Our findings underscore the potential of well-planned SSC applications to improve the fertility of ploughed, acidic sandy soil, taking into account the theory of the circular economy by utilizing wastes and decreasing landfilling. Full article

Significant models predicting Soil Organic Carbon (SOC) and other chemical and biological indicators of soil health in an experimental farm with semi-arid Mediterranean Calcisol have been obtained by partial least squares (PLS) regression, with mid-infrared (MIR) spectra of whole soil samples used as independent variables (IVs). The dependent variables (DVs) included SOC, pH, electric conductivity, N, P₂O₅, K, Ca²⁺, Mg²⁺, Na⁺, Fe, Mn, Cu and Zn. The DVs also included free-living nematodes and microbivores, such as Rhabditids and Cephalobids, and phytoparasitics, such as Xiphinema spp. and other Dorylaimids. More importantly, an attempt was made to determine which spectral patterns allowed each dependent variable (DV) to be predicted. For this purpose, a number of statistical indices were plotted between 4000 and 450 cm⁻¹, e.g., variable importance for prediction (VIP) and beta coefficients from PLS, loading factors from principal component analysis (PCA) and correlation and determination indices. The most effective plots, however, were the “scaled subtraction spectra” (SSS) obtained by subtracting the averages of groups of spectra in order to reproduce the spectral patterns typical in soils where the values of each DV are higher, or vice versa. For instance, distinct SSS resembled the spectra of carbonate, clay, oxides and SOC, whose varying concentrations enabled the prediction of the different DVs. Full article

In recent years, an increasing number of published articles on biocatalysis have reported new enzymes that exhibit biotechnologically interesting catalytic activities. Some authors rush to publish their work in an attempt to ensure “novelty” and often present their results with various types of graphs, such as scatter plots or line-and-symbol plots using nonexistent parameters as ordinates, e.g., “Relative Activity (%)” and the like, vs. abscissae such as pH value, temperature, etc. Nevertheless, in vitro enzyme kinetics remains a valuable tool for understanding, optimizing, and effectively applying these biocatalysts under diverse reaction conditions, taking advantage of all available experimental results. This work aims to emphasize the importance of processing experimental data from enzymatic reactions through appropriate fitting with known kinetic equations and to discourage the use of nonexistent parameters. To support this integrated approach, specific examples are provided for the calculation of significant kinetic and thermodynamic parameters, as well as rate constants. Full article

The success of growing legumes as green manure depends on their spatial and temporal integration within agroecosystems, which minimizes competition with cash crops, and on their nitrogen (N) fixation potential. This study evaluated seven legume species for biomass production, N fixation, and suitability for use in cropping systems in northern Portugal. Oats (Avena sativa L.) were grown to estimate the N fixation using the difference method, as a non-legume reference crop is required for this purpose, and oats are widely grown in the region. The study was conducted over four cropping cycles (2021–2024) in two climate zones across four land plots. The results indicated that the biomass production and N fixation varied by the species/cultivar and cropping cycle, which was significantly influenced by spring precipitation. Broad beans (Vicia faba L.) failed to develop in one cycle on highly acidic soil (pH 4.9), showing negative N fixation values when calculated by the difference method. Conversely, the lupins maintained a relatively high level of N fixation across all the conditions, demonstrating strong environmental adaptability. Thus, the N fixation values across the four cycles ranged from −5.4 to 419.4 kg ha⁻¹ for broad bean (cv. Favel), while yellow lupin (Lupinus luteus L.) exhibited average values between 204.0 and 274.0 kg ha⁻¹. The percentage of N derived from the atmosphere (%Ndfa) ranged from −13.3 to 91.6, −39.4 to 85.8, 83.8 to 94.7, 74.9 to 94.3, 72.8 to 92.2, 23.1 to 75.8, and 11.7 to 21.7 for these species/cultivars. Due to their environmental adaptability, biomass production, and N fixation capacity, these legumes could be used as green manure in inter-rows of woody crops or in summer annual crops like tomatoes and maize, grown in winter as an alternative to fallow land. The lupins showed strong promise due to their environmental resilience. Full article

The major factors affecting the in vitro immature embryo rescue efficiencies from Prunus persica or P. armeniaca accessions have been identified, along with improving the feasibility. Variations in the woody plant medium (WPM) were used depending on the embryo size. Embryos less than 5 mm long were cultured in WPM supplemented with 1 μM BAP and 1 μM GA₃, while embryos bigger than 5 mm long were cultured in hormone-free medium, with or without vermiculite. The environmental in vitro culture conditions consisted of three phases: a (I) stratification at 4 °C during a 3- to 5-month-long period in the dark, followed by (II) growth of germinated embryos at 14 °C for a 4-week-long period, with 12 h light a day, which favors plantlet development, and finally, (III) growth at 24 °C, with 16 h light a day, until the plantlets were acclimatized in the greenhouse. The germination of smaller embryos, at the end of phase I, ranged from 82.2% to 22.1% for apricots and flat peaches, respectively, whereas for bigger embryos, the germination varied from 97.3% to 53.2% for the same species. The embryo germination for peaches and nectarines ranged from 40.1% to 30.3% for smaller embryos, and from 91.9% to 63.0% for bigger embryos. Endo- and epiphytic contamination, affecting from 7.4% to 52.9% of cultured embryos, depending on the fruit type and conservation conditions, and the capacity to acclimate to soil conditions, ranging from 50.4% to 93.2%, were the two most important factors influencing the protocol’s efficiency and feasibility. Considering the overall efficiencies, expressed as hardened plants transferred to field plots over clean uncontaminated embryo, the values ranged from 55.8% for nectarines, 54.0% for peaches, 45.6% for apricots, and 23.3% for flat fruits. The addition of vermiculite to the culture medium significantly improved the plantlet development, avoiding subculture to fresh medium when an extension of phase III was required before acclimatization. Compared to laboratory glassware, the use of food glass containers with air-permeable sealing film, along with vermiculite-containing medium, significantly reduced the costs when handling the large number of embryos required for breeding programs. Full article

Plant proteases, including actinidin, papain and bromelain, have been widely used in the food industry but with limited application in dairy systems. This research aimed to establish and compare operational parameters (kinetics, temperature, enzyme type, time and thermodynamics) relevant to the applications of these enzymes in the hydrolysis of whey protein isolates (WPI), whey protein concentrates (WPC) or milk protein concentrates (MPC). The degree of hydrolysis (DH) increased with the rise in temperature, and the maximum DH was achieved at 60 °C for all three dairy systems. The addition of papain resulted in a greater %DH of whey proteins in comparison to bromelain. The cleavage of proteins was clearly time-dependent (p < 0.05), while the pH did not change significantly (p > 0.05) during this time. PAGE analysis revealed that all three enzymes mainly acted on α-lactalbumin and α_s-casein in WPI and MPC, respectively. Kinetic parameters from the Lineweaver–Burk plot at 60 °C using WPC and MPC as a substrate varied widely, establishing that WPC hydrolysis was characterised by a lower KM, higher kcat, kcat/KM and Vmax compared to MPC in the case of all three enzymes. The difference in kcat/KM values amongst all enzymes (actinidin > papain > bromelain) indicated the difference in the strength of substrate binding sites. The thermodynamic parameters of these enzymes with MPC and WPC were also determined at a temperature range of 15–60 °C, and the results indicate the potential application of papain and actinidin in the dairy industry. Full article

The effect of the demagnetizing factor, regarding the determination of the de-pairing current density $J_{dep}$, has been studied in the case of a Fe(Se,Te) crystal, using DC magnetic measurements as a function of a magnetic field (H) at different temperatures (T). First, the lower critical field $H_{c1}$(T) values were obtained, and the demagnetization effects acting on them were investigated after calculating the demagnetizing factor. The temperature behaviors of both the original $H_{c1}$ values and the ones obtained after considering the demagnetization effects ($H_{c1}^{demag}$) were analyzed, and the temperature dependence of the London penetration depth ${\lambda }_L$(T) was obtained in both cases. In particular, the ${\lambda }_L$(T) curves were fitted with a power law dependence, indicating the presence of low-energy quasiparticle excitations. Furthermore, by plotting ${\lambda }_L^{-2}$ as a function of T, we found that our sample behaves as a multigap superconductor, which is similar to other Fe-11 family iron-based compounds. After that, the coherence length $\mathsf{\xi }$ values were extracted, starting with the $H_{c2}$(T) curve. The knowledge of ${\lambda }_L$ and $\mathsf{\xi }$ allowed us to determine the $J_{dep}$ values and to observe how they are influenced by the demagnetizing factor. Full article

In this project we investigated the extended-gate field-effect transistor (EGFET) structure used with ITO (Indium Tin Oxide)/PET (Polyethylene Terephthalate) sensitive films acting as the extended-gate part of an EGFET obtained from a combination of FETs from the CD4007 chip. We tested the device as a pH sensor by immersing the ITO/PET electrode in several chemical solutions of acidic and basic nature, including hydrogen peroxide, acetic acid, sulfuric acid, and ammonium hydroxide, at different concentrations. Using a Tektronix 4200A sourcemeter, we plotted the current–voltage (I–V) characteristics for the different chemical solutions, and we established a correlation to the pH changes. Results from the plotted I–V characteristics show a great dependance of the drain current (I_D) on solution concentration. Furthermore, we measured the pH of each of the used solutions, and we established a relationship between the drain current and the pH value. Our results show a consistent decrease in the current with an increase in the pH value, although with different rates depending on the solution. The device showed high voltage sensitivity at 0.23 V per pH unit when tested in sulfuric acid. Full article

Water ingress is a common and costly problem in tunnel construction, and understanding the hydrogeological characteristics of a site is crucial for mitigating its effects. This study presents a detailed analysis of the water ingress problems experienced during the construction and operation stages of the Lowari Tunnel in Khyber Pakhtunkhwa, Pakistan, and evaluates the suitability of the water for various purposes. The study found that the water quality varied significantly, depending on the geological conditions and water quantity, with the south portal of the tunnel dominated by Mg cations and bicarbonate anions. The water was found to be suitable for tunnel support systems, including concrete and steel installations, with negligible corrosion observed over the study period. However, the water coming out of the tunnel at the south portal was found to be unsuitable for drinking due to its low pH value. The Wilcox plot classified the water samples as excellent for irrigation, which could benefit local agriculture in the area. The findings of this study can provide valuable insights into the hydrogeological characteristics of the Lowari Tunnel, contributing to the design and construction of similar infrastructure projects in the region. Furthermore, these insights can help improve access to safe and reliable water sources for local communities. Full article

The numerical investigation of magneto-hydrodynamic (MHD) mixed convection flow and entropy formation of non-Newtonian Bingham fluid in a lid-driven wavy square cavity filled with nanofluid was investigated by the finite volume method (FVM). The numerical data-based temperature and nanoparticle size-dependent correlations for the Al${}_2$O${}_3$-water nanofluids are used here. The physical model is a two-dimensional wavy square cavity with thermally adiabatic horizontal boundaries, while the right and left vertical walls maintain a temperature of $T_C$ and $T_H$, respectively. The top wall has a steady speed of $u=u_0$. Pertinent non-dimensional parameters such as Reynolds number ($Re=10,100,200,400$), Hartmann number ($Ha=0,10,20$), Bingham number ($Bn=0,2,5,10,50,100,200$), nanoparticle volume fraction ($\varphi =0,0.02,0.04$), and Prandtl number ($Pr=6.2$) have been simulated numerically. The Richardson number $Ri$ is calculated by combining the values of $Re$ with a fixed value of $Gr$, which is the governing factor for the mixed convective flow. Using the Response Surface Methodology (RSM) method, the correlation equations are obtained using the input parameters for the average Nusselt number ($\overline{Nu}$), total entropy generation ($E_s{)}_t$, and Bejan number ($B{e}_{avg}$). The interactive effects of the pertinent parameters on the heat transfer rate are presented by plotting the response surfaces and the contours obtained from the RSM. The sensitivity of the output response to the input parameters is also tested. According to the findings, the mean Nusselt numbers ($\overline{Nu}$) drop when $Ha$ and $Bn$ are increased and grow when $Re$ and $\varphi$ are augmented. It is found that ${\left(E_s\right)}_t$ is reduced by raising $Ha$, but ${\left(E_s\right)}_t$ rises with the augmentation of $\varphi$ and $Re$. It is also found that the $\varphi$ and $Re$ numbers have a positive sensitivity to the $\overline{Nu}$, while the sensitivity of the $Ha$ and $Bn$ numbers is negative. Full article

A cheap and disposable pencil graphite electrode (PGE) was developed by the incorporation of amine groups (Am-PGE-1). A further improvement in the performance was observed when the aminated electrode (Am-PGE-1) was activated by applying a negative potential scan (Am-PGE-2). The electrochemical transport properties were evaluated through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The Nyquist plot showed a reduced charge transfer resistance value of 24.3 Ω for Am-PGE-2, while it was 95.1 Ω for bare PGE. Thus, Am-PGE-2 was used as a sensing platform for the detection of catechol. It was found that the electrochemical response of catechol oxidation at Am-PGE-2 was twice than the current obtained for bare PGE. Additionally, the effect of pH of the supporting electrolyte and reaction kinetic were studied. The heterogeneous electron transfer rate constant was calculated to be 0.01 s⁻¹. Moreover, CV study revealed that the redox reaction of catechol was a quasi-reversible and diffusion-controlled process. The square wave voltammetry (SWV) technique was applied for the quantitative determination of catechol. The peak current showed a linear dependency on the concentration of catechol from 3 to 150 µM. Furthermore, the analyte could be detected as low as 3.86 µM. Likewise, the sensor demonstrates a good selectivity towards the target analyte than the other possible interfering molecules or ions. Aiming to examine practical applicability, real samples, such as river and household tap water, were tested by using the proposed transducer, and the satisfactory recoveries demonstrate the effectiveness of Am-PGE-2 in real life applications. Full article

Having access to fluorescence lifetime, researchers can reveal in-depth details about the microenvironment as well as the physico-chemical state of the molecule under investigation. However, the high number of influencing factors might be an explanation for the strongly deviating values of fluorescent lifetimes for the same fluorophore reported in the literature. This could be the reason for the impression that inconsistent results are obtained depending on which detection and excitation scheme is used. To clarify this controversy, the two most common techniques for measuring fluorescence lifetimes in the time-domain and in the frequency-domain were implemented in one single microscopy setup and applied to a variety of fluorophores under different environmental conditions such as pH-value, temperature, solvent polarity, etc., along with distinct state forms that depend, for example, on the concentration. From a vast amount of measurement results, both setup- and sample-dependent parameters were extracted and represented using a single display form, the phasor-plot. The measurements showed consistent results between the two techniques and revealed which of the tested parameters has the strongest influence on the fluorescence lifetime. In addition, quantitative guidance as to which technique is most suitable for which research task and how to perform the experiment properly to obtain consistent fluorescence lifetimes is discussed. Full article

As the global energy crisis continues, efficient hydrogen production is one of the hottest topics these days. In this sense, establishing catalytic trends for hydrogen production is essential for choosing proper H₂ generation technology and catalytic material. Volcano plots for hydrogen evolution in acidic media are well-known, while a volcano plot in alkaline media was constructed ten years ago using theoretically calculated hydrogen binding energies. Here, for the first time, we show that the volcano-type relationships are largely maintained in a wide range of pH values, from acidic to neutral and alkaline solutions. We do this using theoretically calculated hydrogen binding energies on clean metallic surfaces and experimentally measured hydrogen evolution overpotentials. When metallic surfaces are exposed to high anodic potentials, hydrogen evolution can be boosted or significantly impeded, depending on the type of metal and the electrolyte in which the reaction occurs. Such effects are discussed here and can be used to properly tailor catalytic materials for hydrogen production via different water electrolysis technologies. Full article

Rising air temperatures caused by global warming affects microbial decomposition rate of soil organic matter (SOM). The temperature sensitivity of SOM decomposition (Q₁₀) may depend on SOM quality determined by vegetation type. In this study, we selected a long transect (3.6 km) across the five ecosystems and short transects (0.1 km) from grazed and ungrazed meadows to forests in the Northwest Caucasus to consider different patterns in Q₁₀ changes at shift of the vegetation belts. It is hypothesized that Q₁₀ will increase along altitudinal gradient in line with recalcitrance of SOM according to kinetics-based theory. The indicators of SOM quality (BR:C, respiration per unit of soil C; MBC:C, ratio of microbial biomass carbon to soil carbon; soil C:N ratio) were used for checking the hypothesis. It was shown that Q₁₀ did not differ across vegetation types within long and short transects, regardless differences in projective cover (14–99%) and vegetation species richness (6–12 units per plot). However, Q₁₀ value differed between the long and short transects by almost two times (on average 2.4 vs. 1.4). Such a difference was explained by environmental characteristics linked with terrain position (slope steepness, microclimate, and land forms). The Q₁₀ changes across studied slopes were driven by BR:C for meadows (R² = 0.64; negative relationship) and pH value for forests (R² = 0.80; positive relationship). Thus, proxy of SOM quality explained Q₁₀ variability only across mountain meadows, whereas for forests, soil acidity was the main driver of microbial activity. Full article

Bryophytes are commonly used in biomonitoring heavy metal pollution, whereas the bioindicative value of bryophyte communities is a less known issue. The aim of the present study is to recognize the utility of the bryophyte community’s structure in the assessment of soil condition in heavy metal-polluted, dry grasslands. The study plots are examined with respect to bryophytes; vascular plants; concentrations of Zn, Pb, Cd, and As in the soil; total nitrogen and organic carbon content in the soil; and soil pH. The results show that both bryophyte species richness and composition greatly depend on soil chemical characteristics, including heavy-metal pollution levels and soil pH. Three groups of species are distinguished: (1) species sensitive to pollution growing on acidic soils, (2) nonspecific species inhabiting a wide spectrum of heavy metal-polluted sites, and (3) species preferring polluted and alkaline soils. Our study reveals a gradual replacement of the bryophyte species alongside increasing soil pollution and alkalinity. This proves that bryophytes are highly responsive to soil factors and the changes in bryophyte composition may indicate the soil condition of a certain site. Furthermore, high concentrations of heavy metals in the soil and an alkaline pH positively affect bryophyte species richness. Consequently, such sites could be considered as biodiversity hotspots for terrestrial bryophytes in post-industrial landscapes. Full article