Search Results (59)

Oily wastewater treatment is crucial for protecting the environment and ensuring sustainable water use. The current study examines the effectiveness of electrocoagulation in treating oily wastewater by conducting several batch experiments designed to determine the best operating conditions. Various factors affecting the performance of electrocoagulation, such as applied current density, electrode type, and pH, were studied. The results indicate that, under ideal conditions, electrocoagulation worked very well. The best results were obtained by involving an applied current density of 6 mA/cm², a mild steel anode, and a pH of 6.7. Under these conditions, the process removed 94% of the chemical oxygen demand (COD) from the oily wastewater. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectrometry (EDAX) were used to characterize the residual sludge left in the reactor. The characterization results show that the oily pollutants were successfully removed through electroflotation. Additionally, oil precipitate particles were easily coated during the electrocoagulation operation. The findings show that electrocoagulation is an effective method for treating oil-contaminated wastewater. Full article

The growing demand for dermocosmetics with ingredients of natural origin reflects the pivotal role of cutaneous health and appearance in consumer self-esteem. Under this context, clays have attracted attention for their potential applications in dermatological care. Our research work aimed to increase knowledge on the short-term impact of cosmetic formulations containing a blend of red, green, and black clays, assessing their effects on sebum regulation and in cutaneous biomechanical behavior (firmness/elasticity). Unlike daily skincare products, clay masks are used infrequently and for short durations; thus, an in vivo assessment was conducted after a 2-h application to reflect typical consumer use. The mineralogical and physicochemical properties of the different clays were characterized. Mineralogical analysis revealed distinct compositions among the clays: black clay exhibited a simpler mineral profile, lower density, and smaller particle size; green clay contained expandable smectite and was the densest; and red clay displayed the largest average particle size and highest iron content. Thermal analysis identified two major transitions: dehydration and kaolinite dehydroxylation. In vivo studies conducted in participants showed a significant reduction in skin oiliness across all clay-based formulations compared to baseline, control, and placebo following a 2-h application, and the rebound sebum production was dependent on clay concentration. Cutometry measurements did not reveal statistically significant improvements in skin firmness or elasticity compared to the control and placebo. The findings suggested that while clay-based formulations effectively reduced skin oiliness in the short term, their impact on sebum regulation and on skin biomechanical properties was limited after such a short product application period. Additional studies are warranted to elucidate the distinct effects of each clay, assess their behavior in different formulation bases, and evaluate their efficacy after repeated use. Full article

Oily wastewater is a critical environmental concern, and the high costs and fouling of conventional membranes drive the search for low-cost, efficient alternatives. This study evaluates surface-modified quartz particles for oil–water separation, focusing on hydrophilic and hydrophobic coatings. Quartz samples underwent washing, hydrophobic coating, and hydrophilic coating, with morphological and elemental changes assessed using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDS). Oil and grease (O&G) content was determined via the EPA 1664 method under high-solids conditions. The untreated oil–water mixture contained 142,955.9 mg/L O&G. Hydrophilic-coated quartz achieved the greatest reduction, producing water with only 751.3 mg/L O&G, indicating excellent oil rejection and water selectivity. Washed quartz performed similarly at 837.1 mg/L. Hydrophobic-coated quartz, while yielding higher residual oil in water (64,198.9 mg/L), demonstrated strong oil affinity, making it more suitable for oil recovery applications. Raw quartz, tested without heavy oil loading, showed a baseline of 13.4 mg/L. These results confirm that surface engineering of quartz enables tunable separation properties, where hydrophilic surfaces favor water purification and hydrophobic surfaces enhance oil capture. The findings provide a pathway for scalable, cost-effective, and application-specific oily wastewater treatment solutions. Full article

The effective and rapid separation of oil–water emulsions at room temperature, particularly under harsh environmental conditions like acid–base fluctuations, high salinity, and the coexistence of surfactants, remains a significant challenge in oily wastewater treatment. To address this, a novel amphiphilic demulsifier, MOF-74@SiO₂-GPTMS grafted ANP (MSG-ANP), was synthesized by first modifying MOF-74@SiO₂ (MS) with γ-glycidoxypropyltrimethoxysilane (GPTMS) to create epoxy-functionalized MSG particles, followed by grafting the non-ionic polyether C₁₂–C₁₄ aliphatic polyethylene oxide polyoxypropylene (ANP) onto MSG. Bottle tests demonstrated that MSG-ANP achieved a high demulsification efficiency of 93% within 15 min for oil-in-water emulsions at room temperature. It exhibited excellent environmental tolerance, maintaining efficiencies of 89% at pH 3.0, 82% at pH 11.0, and 95% under high salinity (50,000 mg/L, pH 6.8). Furthermore, MSG-ANP effectively treated surfactant-stabilized emulsions, exceeding 96% efficiency against both cetyltrimethylammonium bromide and sodium dodecyl sulfate after 30 min, outperforming commercial demulsifiers SP-169 and AR-331 by factors of 1.2 and 1.6, respectively. This superior performance stems from synergistic hydrogen bonding (via hydroxyl, ether, ester, Fe-O, and Si-O groups) destabilizing the interfacial film and electrostatic neutralization of coalescing charged droplets. Consequently, MSG-ANP presents a promising solution for rapid, room-temperature demulsification across a wide pH range and under high-salinity conditions. Full article

The discharge of oily wastewater threatens the ecosystem and human health, and the efficient treatment of oily wastewater is confronted with problems of high mass transfer resistance at the oil-water-solid multiphase interface, significant light shielding effect, and easy deactivation of photocatalysts. Although traditional physical separation methods avoid secondary pollution by chemicals and can effectively separate floating oil and dispersed oil, they are ineffective in removing emulsified oil with small particle sizes. To address these complex challenges, photocatalytic technology and photocatalysis-based improved technologies have emerged, offering significant application prospects in degrading organic pollutants in oily wastewater as an environmentally friendly oxidation technology. In this paper, the degradation mechanism, kinetic mechanism, and limitations of conventional photocatalysis technology are briefly discussed. Subsequently, the surface interface modulation functions of metal doping and heterojunction energy band engineering, along with their applications in enhancing the light absorption range and carrier separation efficiency, are reviewed. Focus on typical studies on the separation and degradation of aqueous and oily phases using photocatalytic membrane technology, and illustrate the advantages and mechanisms of photocatalysts loaded on the membranes. Finally, other new approaches and converging technologies in the field are outlined, and the challenges and prospects for the future treatment of oily wastewater are presented. Full article

This study explores the development and optimization of quartz-based filtration media for industrial oil–water separation, focusing on enhancing surface wettability, minimizing fouling, and improving oil rejection efficiency. High-purity quartz particles (SiO₂: 98%, Fe₂O₃: 0.18%, particle size: 0.8–1.8 mm) were evaluated in three configurations: raw, acid-washed, and surface-coated with hydrophilic nanoparticles (Al₂O₃ and P₂O₅). The filtration medium was constructed as a packed-bed of quartz particles rather than a continuous sintered membrane, providing a cost-effective and modular structure for separation processes. Comprehensive material characterization was performed using X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS). XRD confirmed the crystalline stability of quartz across all treatments, while SEM and EDS revealed enhanced surface morphology and elemental distribution—especially phosphorus and aluminum—in coated samples. Performance testing with synthetic oily wastewater (initial oil concentration: 183,754.8 mg/L) demonstrated that the coated quartz medium achieved superior separation, reducing residual oil concentration to 29.3 mg/L, compared to 1583.7 mg/L and 1859.8 mg/L for washed and raw quartz, respectively. Contact angle analysis confirmed improved hydrophilicity in coated media, which also exhibited lower fouling propensity. Taguchi optimization (conducted via Minitab 21.3) and regression modeling identified surface coating and operational pressure (optimal at 2.5 bar) as the most significant parameters influencing oil rejection. Post-filtration SEM and XRD confirmed structural integrity and coating durability. Additionally, flux recovery above 90% after backwashing indicated strong regeneration capability. These findings validate surface-modified quartz packed beds as robust, scalable, and economically viable alternatives to conventional membranes in oily wastewater treatment. Future research will explore multilayer coatings, long term performance under aggressive conditions, and AI-based prediction models. Full article

Janus nanorods are a special class of nanorods composed of two distinct surface regions, one hydrophilic and one hydrophobic. This amphiphilic characteristic makes them promising candidates for stabilizing water–oil interfaces. Oily wastewater (OWW) contamination, resulting from industrial activities such as petroleum extraction and refining and vegetable oil processing, poses significant risks to ecosystems, water resources, and public health. Traditional surfactants used in enhanced oil recovery (EOR) and wastewater treatment often introduce secondary pollution due to their persistence and toxicity. In this work, we investigate the interfacial behavior of Janus NRs under two different conditions: a thin oil film surrounded by water and a nanoconfined system with purely repulsive walls. Using dissipative particle dynamics (DPD) simulations, we analyze how nanorod length and confinement influence interfacial tension and self-assembly. In bulk systems, shorter NRs (dimers and quadrimers) effectively reduce interfacial tension by adsorbing at the oil–water interface, while longer NRs (hexamers) exhibit bulk aggregation, limiting their surfactant efficiency. In contrast, under nanoconfinement, all NR sizes increase interfacial tension due to steric constraints, with longer NRs preferentially adsorbing onto the solid–liquid interface. These results pave the way for the rational design of nanostructured materials for applications in enhanced oil recovery, wastewater treatment, and membrane filtration. Full article

Cyclone separation is a widely utilized separation technique, which enables the self-rotation behaviors of particles in the internal flow field, in order to realize high-performance separation of mixtures. Oily sludges are solid wastes generated by the shale gas industry, which need to be properly treated for environmental protection. In the present investigation, we demonstrated that tuning the inlet flow pattern of the cyclone from linear flow to vortex flow is an effective approach to boost the rotation speed of oily sludge particles for obtaining significantly improved separation effects. Numerical simulations were carried out to investigate the influences of inlet flow pattern on the rotation behaviors of particles, which manifested in the rotation speed of particles being evidently increased up to 4500 rad/s when the inlet flow was tuned from a unidirectional pattern into vortex pattern. The effective rotation zone’s area was also found to increase significantly, with the area of the effective rotation zone enlarged by up to 400%. Further separation experiments on oily sludge were carried out using a cyclone equipped with a worm shell that generated vortex inlet flow with rotating blades. Separation results confirmed that the oily sludge was successfully purified by the cyclone equipped with a worm shell, which provided an extremely high oil removal percentage of 99.9%, showing a 49.1% enhancement in oil removal capability over the individual cyclone separation. Our investigations demonstrated an effective method for realizing oily sludge treatment and oil resource recovery by conventional cyclone separation. Full article

Background/Objectives: The present study focused on the formulation and evaluation of novel topical systems containing Salvia officinalis (sage), emphasizing their antioxidant and anti-inflammatory properties. Sage, rich in carnosol, offers considerable therapeutic potential, yet its low water solubility limits its effectiveness in traditional formulations. The aim of our experimental work was to improve the solubility and thus bioavailability of the active ingredient by developing self-nano/microemulsifying drug delivery systems (SN/MEDDSs) with the help of Labrasol and Labrafil M as the nonionic surfactants, Transcutol HP as the co-surfactant, and isopropyl myristate as the oily phase. Methods: The formulations were characterized for droplet size, zeta potential, polydispersity index (PDI), encapsulation efficacy, and stability. The composition exhibiting the most favorable characteristics, with particle sizes falling within the nanoscale range, was incorporated into a cream and a gel, which were compared for their textural properties, carnosol penetration, biocompatibility and efficacy. Results: Release studies conducted using Franz diffusion cells demonstrated that the SNEDDS-based cream achieved up to 80% carnosol release, outperforming gels. The 2,2-diphenyl-1-picrylhydrazyl (DPPH) test and enzyme-linked immunosorbent assays (ELISA) showed strong efficacy, with an in vivo carrageenan-induced rat paw edema model revealing that the SNEDDS-based cream significantly reduced inflammation. Conclusions: These findings highlight the potential of SNEDDS-enhanced topical formulations in improving therapeutic outcomes. Further research is warranted to confirm their long-term safety and efficacy. Full article

Scrub bars are an innovative alternative to traditional liquid, semi-liquid, and oily body scrubs. Through the elimination of water from their formulas, they align with the current ‘waterless’ trend in the cosmetics market. The aims of this study were to create anhydrous formulations for body scrub bars and to assess their physical, chemical, and sensory characteristics depending on the type of exfoliant added. A total of five solid body scrub formulations were developed using different natural exfoliants: sugar, microcrystalline cellulose, ground coffee beans, corn granules, and sodium chloride. The shape and dimensions of the exfoliant particles were characterized by scanning electron microscopy (SEM). The formulations were subjected to texturometric tests. The final products underwent color assessment along with a consumer evaluation of sensory appeal. The test results showed that the body scrubs exhibiting the highest hardness and adhesive force were those containing exfoliants with small particles, either angular (sodium chloride) or subrounded (Coffea arabica seed powder) in shape. Conversely, the lowest hardness was determined for the product formulated with the addition of an exfoliant with well-rounded particles (microcrystalline cellulose). Among the exfoliants tested, microcrystalline cellulose proved to be the most suitable for body scrubs, demonstrating superior texture and exfoliating effectiveness. However, cosmetics containing ground coffee received the highest esthetic ratings. Coffee gave the product a natural color and an appealing scent, as judged by the testers. Full article

The solid phase composition in oily sludge (OS) is a key factor affecting the oil–solid separation of OS. In this paper, the effects and mechanisms of solid-phase particle factors on the oil content of residue phase were investigated in order to improve the oil–solid separation efficiency. Flotation experiments were carried out on single-size sand and mixed-size sand OS consisting of three particle sizes at room temperature without adding flotation reagents. The effects of different-size particles as solid phase composition of OS and flotation parameter settings such as flotation temperature (Tp), flotation time (Tt), impeller speed (Rs) and liquid-solid ratio (L/OS) on the oil–solid separation efficiency were investigated. The experimental results showed that the oil content of residue phase decreased with the increasing of solid-phase particle size for single-size sand OS, and the optimal flotation conditions were Tp of 50 °C, Tt of 25 min, Rs of 1450 r/min and L/OS of 12:1. The oil–solid separation was more pronounced for mixed-size sand OS with a complex particle composition, while different particle compositions of the solid phase in OS promoted oil–solid separation. Scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) characterisation of OS before and after flotation confirmed the relative advantage of coarse particle OS in the oil–solid separation process. The classical first-order model was well fitted to the flotation kinetic process of single-size sand and mixed-size sand OS. The response surface methodology (RSM) method was used to determine the Rs as the main control factor of the flotation process, and the oil content of residue phase in mixed-size sand OS was optimised to 2.63%. This study provides important process parameters and theoretical basis for the efficient treatment of OS. Full article

Background/Objectives: Nanoemulsions (NEs) possess properties that enhance the solubility, bioavailability and therapeutic efficacy of drugs. Chalcones are compounds known for their antifungal properties. In this study, we evaluated different emulsification techniques to create alginate nanoemulsions containing chalcone (1E,4E)-1,5-bis (4-methoxyphenyl) penta-1,4-dien-3-one (DB4OCH₃). Our goal was to develop an antifungal formulation targeting Candida albicans strains. Methods: Ultrasound and ultrasound combined with high-speed homogenization techniques were used to prepare alginate-stabilized nanoemulsions. Particle size, zeta potential and encapsulation efficiency were evaluated. Additionally, in vitro release studies were conducted. Results: The combined emulsification technique produced stable nanoparticles with high encapsulation efficiency and antifungal activity, with a minimum inhibitory concentration of 8.75 μg/mL for the nanoemulsions compared to 312 µg/mL for free DB4OCH₃. NEs’ effectiveness can be attributed to their ability to form nanodroplets efficiently, facilitating the solubilization of the chalcone in the oily phase. The particle size varied between 195.70 ± 2.69 and 243.40 ± 4.49 nm, with an increase in chalcone concentration leading to larger particle sizes. The zeta potential showed values from −91.77 ± 5.58 to −76.90 ± 4.44 mV. The UHS-7 sample exhibited an encapsulation efficiency of 92.10% ± 0.77, with a controlled in vitro release of 83% after 34 h. Molecular docking simulations showed that the aromatic nature of DB4OCH₃ resulted in the formation of apolar interactions with aromatic residues located in the active site of the TMK, as observed in their respective co-crystallized inhibitors, within an affinity energy range that enables optimum specificity of the ligand for these two pathways. Pharmacokinetic analyses indicated high passive cell permeability and low hepatic clearance, and phase I metabolism reduces its oral bioavailability and metabolic stability, suggesting a promising active ingredient as an oral drug with control of the daily oral dose administered. Conclusions: The combined nanoemulsification technique led to the formation of finely dispersed nanodroplets that favored the solubilization of the chalcone in the oil phase, which led to a better performance in the antifungal properties. DB4OCH₃ shows promise as an oral drug with controlled dosing. Full article

Oily sludge (OS) has long been regarded as a hazardous waste, and improper disposal may lead to serious environmental concerns and human health risks. Despite various methods having been proposed and applied to the treatment of OS, the oil occurrence states and properties in sludge are rarely characterized, which may directly link to the selection and effectiveness of treatment methods. Here, confocal laser scanning microscopy (CLSM), X-ray diffraction (XRD), gas chromatography (GC), and four components (SARA) analysis were utilized to characterize the changes in the oil occurrence states and compositions in OS samples before and after high-speed stirring (HSS) treatment. Our results show a substantial reduction in the oil concentration of OS after HSS treatment (from 32.98% to 1.65%), while SARA analysis reveals a similar oil composition before and after treatment, suggesting the broad applicability of HSS in removing oil and its insignificant selectivity towards various hydrocarbon components. This is further supported by the total petroleum hydrocarbon (TPH) analysis results, which show that the separated oil phase has a hydrocarbon composition similar to that of the original OS sample. The CLSM and fluorescence analysis suggest a homogeneous distribution of oil in the sludge, with relatively light components more concentrated in the pore systems between coarse mineral particles, whereas relatively heavy components tend to coexist with clay minerals. After HSS cleaning, both light and heavy components are removed to varying degrees, but light components are preferentially removed while heavy components tend to be retained in the sludge due to adsorption by clay minerals. This is consistent with TPH analysis, where a significant decrease in n-alkanes with lower carbon numbers (n-C14 to n-C20) was observed in the residual sample. Our findings demonstrate the dynamic response of oil occurrence states and compositions to the OS treatment process and highlight the importance of characterizing these fundamental properties prior to the selection of OS treatment methods. Full article

The health benefits of long-chain omega-3 polyunsaturated fatty acid (LCn-3PUFA) intake have been well documented. However, currently, the consumption of oily fish (the richest dietary source of LCn-3PUFA) in the UK is far below the recommended level, and the low digestibility of LCn-3PUFA bulk oil-based supplements from triglyceride-based sources significantly impacts their bioavailability. LCn-3PUFA-rich microalgal oil offers a potential alternative for populations who do not consume oily fish, and nanoemulsions have the potential to increase LCn-3PUFA digestibility and bioavailability. The aims of this study were to produce stable algal oil-in-water nanoemulsions with ultrasonic technology to increase DHA digestibility, measured using an in vitro digestion model. A nanoemulsion of LCn-3PUFA algal oil was developed with 6% w/w emulsifiers: lecithin (LE) or an equal ratio of Tween 40 (3%) and lecithin (LTN) (3%), 50% w/w, algal oil and 44% w/w water using rotor–stator and ultrasound homogenization. The in vitro digestion experiments were conducted with a gastric and duodenal digestion model. The results showed the creation of nanoemulsions of LCn-3PUFA algal oils offers potentially significant increases in the bioavailability of DHA in the human body. The increase in digestibility can be attributed to the smaller particle size of the nanoemulsions, which allows for higher absorption in the digestive system. This showed that the creation of nanoemulsions of LCn-3PUFA algal oils offers a potentially significant increase in the bioavailability of DHA in the human body. The LE and LTN nanoemulsions had average droplet sizes of 0.340 ± 0.00 µm and 0.267 ± 0.00 µm, respectively, but the algal oil mix (sample created with same the components as the LTN nanoemulsion, hand mixed, not processed by rotor–stator and ultrasound homogenization) had an average droplet size of 73.6 ± 6.98 µm. The LTN algal oil nanoemulsion was stable in the gastric and duodenal phases without detectable destabilization; however, the LE nanoemulsion showed signs of oil phase separation in the gastric phase. Under the same conditions, the amount of DHA digested from the LTN nanoemulsion was 47.34 ± 3.14 mg/g, compared to 16.53 ± 0.45 mg/g from the algal oil mix, showing DHA digestibility from the LTN nanoemulsion was 2.86 times higher. The findings of this study contribute to the insight of in vitro DHA digestion under different conditions. The stability of the LTN nanoemulsion throughout digestion suggests it could be a promising delivery system for LCn-3PUFAs, such as DHA, in various food and pharmaceutical applications. Full article

In the field of preparing cosmetic formulations, recent advances recommend the usage of excipients derived from biocompatible materials. In this context, the present study aimed to prepare and characterize the curcumin-loaded Pickering emulsion for possible applications in cosmetic formulation. The coconut oil which is often the component of skin care formulations is used as the oily phase. Curcumin, which is well known for absorbing solar radiation, is expected to work synergistically with coconut oil towards improving the sun protection factor (SPF) of the formulation. Additionally, curcumin can also protect the intracellular components through its well-known antioxidant mechanisms. The Pickering emulsion of coconut oil into water was prepared using the composite colloidal particles derived from β-carboxymethyl chitosan (CMC) and Gelatin-A (GA) as the emulsifying agent. The reaction conditions in terms of the weight ratios of CMC and GA, the pH of the reaction medium, the oil volume fraction, and the homogenization speed were optimized to obtain the most stable Pickering emulsion. The obtained systems were physico-chemically characterized by dynamic light scattering, zeta potential, optical microscopy, and rheometric measurements. The final CMC-GA-stabilized emulsion demonstrated an oil droplet size of 100 µm and a SPF_{spectrophotometric (290–320 nm)} value of 8.5 at a curcumin loading of 4 mg/mL. Additionally, the final formulation facilitated the uptake of curcumin into fibroblast (WI26) cells under in vitro conditions. Together, the investigation demonstrates a bio-inspired approach to prepare a curcumin-loaded green Pickering emulsion using biocompatible pharmaceutical grade excipients, which may find utility in cosmetic applications. Full article