Search Results (221)

Grain boundaries are among the most influential structural features that control the charge transport in polycrystalline organic semiconductors. Acting as both charge trapping sites and electrostatic barriers, they disrupt molecular packing and introduce energetic disorder, thereby limiting carrier mobility, increasing threshold voltage, and degrading the stability of organic thin-film transistors (OTFTs). This review presents a detailed discussion of grain boundary formation, their impact on charge transport, and experimental strategies for engineering their structure and distribution across several high-mobility small-molecule semiconductors, including pentacene, TIPS pentacene, diF-TES-ADT, and rubrene. We explore grain boundary engineering approaches through solvent design, polymer additives, and external alignment methods that modulate crystallization dynamics and domain morphology. Then various case studies are discussed to demonstrate that optimized processing can yield larger, well-aligned grains with reduced boundary effects, leading to great mobility enhancements and improved device stability. By offering insights from structural characterization, device physics, and materials processing, this review outlines key directions for grain boundary control, which is essential for advancing the performance and stability of organic electronic devices. Full article

This study presents a photoresist-free patterning method for solution-processed indium zinc oxide (IZO) thin films using two photochemical exposure techniques, namely pulsed ultraviolet (UV) light and UV-ozone, and a plasma-based method using oxygen (O₂) plasma. Pulsed UV light delivers short, high-intensity flashes of light that induce localised photochemical reactions with minimal thermal damage, whereas UV-ozone enables smooth and uniform surface oxidation through continuous low-pressure UV irradiation combined with in situ ozone generation. By contrast, O₂ plasma generates ionised oxygen species via radio frequency (RF) discharge, allowing rapid surface activation, although surface damage may occur because of energetic ion bombardment. All three approaches enabled pattern formation without the use of conventional photolithography or chemical developers, and the UV-ozone method produced the most uniform and clearly defined patterns. The patterned IZO films were applied as active layers in bottom-gate top-contact thin-film transistors, all of which exhibited functional operation, with the UV-ozone-patterned devices exhibiting the most favourable electrical performance. This comparative study demonstrates the potential of photochemical and plasma-assisted approaches as eco-friendly and scalable strategies for next-generation IZO patterning in electronic device applications. Full article

Background: Sirolimus (SRL, rapamycin) is a clinically important mTOR inhibitor used in immunosuppression, oncology, and cardiovascular drug-eluting devices. Despite its long-standing FDA approval, the human metabolic profile of SRL remains incompletely characterized. SRL is primarily metabolized by CYP3A enzymes in the liver and intestine, but the diversity, pharmacokinetics, and biological activity of its metabolites have been poorly explored due to the lack of structurally identified standards. Methods: To investigate SRL metabolism, we incubated SRL with pooled human liver microsomes (HLM) and isolated the resulting metabolites. Structural characterization was performed using high-resolution mass spectrometry (HRMS) and ion trap MSⁿ. We also applied Density Functional Theory (DFT) calculations to assess the energetic favorability of metabolic transformations and conducted molecular dynamics (MD) simulations to model metabolite interactions within the CYP3A4 active site. Results: We identified 21 unique SRL metabolites, classified into five major structural groups: O-demethylated, hydroxylated, didemethylated, di-hydroxylated, and mixed hydroxylated/demethylated derivatives. DFT analyses indicated that certain demethylation and hydroxylation reactions were energetically preferred, correlating with metabolite abundance. MD simulations further validated these findings by demonstrating the favorable orientation and accessibility of key sites within the CYP3A4 binding pocket. Conclusions: This study provides a comprehensive structural map of SRL metabolism, offering mechanistic insights into the formation of its metabolites. Our integrated approach of experimental and computational analyses lays the groundwork for future investigations into the pharmacodynamic and toxicodynamic effects of SRL metabolites on the mTOR pathway. Full article

In current and future fusion devices, detecting hydrogen isotopes, particularly tritium and deuterium, implanted or redeposited on the surface of Plasma-Facing Components (PFCs) will be increasingly important to ensure safe machine operations. The Laser-Induced Breakdown Spectroscopy (LIBS) technique has proven capable of performing this task directly in situ, without handling or removing PFCs, thus limiting analysis times and increasing the machine’s duty cycle. To increase sensitivity and the ability to discriminate between isotopes, LIBS analysis can be performed under different background gases at atmospheric pressure, such as air, He, and Ar. In this work, we present the results obtained on tungsten coatings enriched with deuterium and/or hydrogen as a deuterium–tritium nuclear fuel simulant, measured with the LIBS technique in air, He, and Ar at atmospheric pressure, and discuss the pros and cons of their use. The results obtained demonstrate that both He and Ar can improve the LIBS signal resolution of the hydrogen isotopes compared to air. However, using Ar has the additional advantage that the same procedure can also be used to detect He implanted in PFCs as a product of fusion reactions without any interference. Finally, the LIBS signal in an Ar atmosphere increases in terms of the signal-to-noise ratio (SNR), enabling the use of less energetic laser pulses to improve performance in depth profiling analyses. Full article

Semiconductor device fabrication is conducted through highly precise manufacturing processes. An essential component of the semiconductor package is the lead frame on which the silicon dies are assembled. Impurities such as oxides or organic matter on the surfaces have an impact on the process yield. Plasma cleaning is a vital process in semiconductor manufacturing, employed to enhance production yield through precise and efficient surface preparation essential for device fabrication. This paper explores the various facets of plasma cleaning, with a particular emphasis on its application in the cleaning of lead frames used in semiconductor packaging. To provide comprehensive context, this paper also reviews the critical role of plasma in advanced and emerging packaging technologies. This study investigates the fundamental physics governing plasma generation, the design of plasma systems, and the composition of the plasma medium. A central focus of this work is the comparative analysis of different plasma systems in terms of their effectiveness in removing organic contaminants and oxide residues from substrate surfaces. By utilizing reactive species generated within the plasma—such as oxygen radicals, hydrogen ions, and other chemically active constituents—these systems enable a non-contact, damage-free cleaning method that offers significant advantages over conventional wet chemical processes. Additionally, the role of non-reactive species, such as argon, in sputtering processes for surface preparation is examined. Sputtering is the ejection of individual atoms from a target surface due to momentum transfer from an energetic particle (usually an ion). Sputtering is therefore a physical process driven by momentum transfer. Energetic ions, such as argon (Ar⁺), are accelerated from the plasma to bombard a target surface. Upon impact, these ions transfer sufficient kinetic energy to atoms within the material’s lattice to overcome their surface binding energy, resulting in their physical ejection. This paper also provides a comparative assessment of various plasma sources, including direct current, dielectric barrier discharge, radio frequency, and microwave-based systems, evaluating their suitability and efficiency for lead frame cleaning applications. Furthermore, it addresses critical parameters affecting plasma cleaning performance, such as gas chemistry, power input, pressure regulation, and substrate handling techniques. The ultimate aim of this paper is to provide a concise yet comprehensive resource that equips technical personnel with the essential knowledge required to make informed decisions regarding plasma cleaning technologies and their implementation in semiconductor manufacturing. This paper provides various tables which provide the reader with comparative assessments of the various plasma sources and gases used. Scoring mechanisms are also introduced and utilized in this paper. The scores achieved by both the sources and the plasma gases are then summarized in this paper’s conclusions. Full article

Polynitrogen compounds have broad applications in the field of high-energy materials, making the exploration of two-dimensional polynitride materials with both novel properties and practical utility a highly attractive research challenge. Through global structure search methods and first-principles theoretical calculations at the Perdew–Burke–Ernzerhof (PBE) level of density functional theory (DFT), the globally minimum-energy configuration of a novel planar BeN₃ monolayer (tetr-2D-BeN₃) is predicted. This material exhibits a planar quasi-isotropic structure containing pentagonal, hexagonal, and dodecagonal rings, as well as “S”-shaped N6 polymeric units, exhibiting a high energy density of 3.34 kJ·g⁻¹, excellent lattice dynamic stability and thermal stability, an indirect bandgap of 2.66 eV (HSE06), high carrier mobility, and ultraviolet light absorption capacity. In terms of mechanical properties, it shows a low in-plane Young’s stiffness of 52.3–52.9 N·m⁻¹ and a high in-plane Poisson’s ratio of 0.55–0.56, indicating superior flexibility. Furthermore, its porous structure endows it with remarkable selectivity for hydrogen (H₂) and argon (Ar) gas separation, achieving a maximum selectivity of up to 10²³ (He/Ar). Therefore, the tetr-2D-BeN₃ monolayer represents a multifunctional two-dimensional polynitrogen-based energetic material with potential applications in energetic materials, flexible semiconductor devices, ductile materials, ultraviolet photodetectors, and other fields, thereby expanding the design possibilities for polynitride materials. Full article

The broadening adoption of interconnected systems within smart city environments is fundamental for the progression of digitally driven economies, enabling the refinement of city administration, the enhancement of public service delivery, and the fostering of ecologically sustainable progress, thereby aligning with global sustainability benchmarks. However, the pervasive distribution of Internet of things (IoT) apparatuses introduces substantial security risks, attributable to the confidential nature of processed data and the heightened susceptibility to cybernetic intrusions targeting essential infrastructure. Commonly, these devices exhibit deficiencies stemming from restricted computational capabilities and the absence of uniform security standards. The resolution of these security challenges is paramount for the full realization of the advantages afforded by IoT without compromising system integrity. Cryptographic protocols represent the most viable solutions for the mitigation of these security vulnerabilities. However, the limitations inherent in IoT edge nodes complicate the deployment of robust cryptographic algorithms, which are fundamentally reliant on finite-field multiplication operations. Consequently, the streamlined execution of this operation is pivotal, as it will facilitate the effective deployment of encryption algorithms on these resource-limited devices. Therefore, the presented research concentrates on the formulation of a spatially and energetically efficient hardware implementation for the finite-field multiplication operation. The proposed arithmetic unit demonstrates significant improvements in hardware efficiency and energy consumption compared to state-of-the-art designs, while its systolic architecture provides inherent timing-attack resistance through deterministic operation. The regular structure not only enables these performance advantages but also facilitates future integration of error-detection and masking techniques for comprehensive side-channel protection. This combination of efficiency and security makes the multiplier particularly suitable for integration within encryption processors in resource-constrained IoT edge nodes, where it can enable secure data communication in smart city applications without compromising operational effectiveness or urban development goals. Full article

Passive Dynamic Ankle–Foot Orthoses (PD-AFOs) are medical devices prescribed to individuals with foot drop, a condition characterized by weakness of the ankle dorsiflexor muscles. PD-AFOs can store and release energy during the stance phase of the gait cycle, while supporting the foot in the swing phase. This study aimed at estimating the energetics of a novel fiberglass-reinforced polyamide custom PD-AFO in a population of mild foot drop patients. Eight PD-AFOs were designed and 3D-printed via selective laser sintering for eight participants with a unilateral foot drop condition. Lower limb kinematics and AFO flexion/extension were recorded during comfortable walking speed via skin marker-based stereophotogrammetry. The stiffness of each AFO was measured via an ad hoc experimental setup. The elastic work performed by the PD-AFO during gait was calculated as the dot product of the calf-shell resisting moment and the rotation angle. The average maximum energy stored by the calf-shell across all PD-AFOs was 0.013 ± 0.005 J/kg. According to this study, 3D-printed custom PD-AFOs made with fiberglass-reinforced polyamide can store some elastic energy, which is released to the ankle during push-off. Further studies should be conducted to assess the effect of this energy return mechanism in improving the gait of individuals with deficits of the ankle plantarflexor muscles. Full article

Li/graphite fluoride (Li/CF_x) batteries display the highest energy densities among those of commercially available primary Li batteries but fail to satisfy the high-performance requirements of advanced applications. To address this drawback, two liquid organic dinitrates, namely, 1,4-butanediol dinitrate (BDE) and 2,2,3,3-tetrafluoro-1,4-butanediol dinitrate (TBD), were employed as high-energy energetic materials, and they were highly compatible with the electrolytes of Li/CF_x batteries. The use of Super P electrodes confirmed that the reduction reaction mechanisms of both nitrate ester-based compounds delivered considerable specific capacities, associated with discharge potentials matching that of the Li/CF_x battery. When considering the combined mass of the electrolyte and cathode as the active material, the overall energy densities of the Li/CF_x batteries increased by 25.3% (TBD) and 20.8% (BDE), reaching 1005.50 and 969.1 Wh/kg, respectively. The superior performance of TBD was due to the synergistic effects of the high electronegativities and levels of steric hindrance of the F atoms. Moreover, the nanocrystal LiF particles generated by TBD induced crack formation within the fluorinated graphite, increasing the lithium-ion accessible surface area and enhancing its utilization efficiency. These combined factors enhanced the reactivity of TBD and facilitated its involvement in electrochemical reactions, thus improving the capacity of the battery. The developed strategy enables the facile, cost-effective enhancement of the capacities of Li/CF_x batteries, paving the way for their practical use in energy-demanding devices. Full article

Energetic structural materials (ESMs) are widely studied due to their high energy density, which enhances their potential in various industrial and engineering applications, such as in energy absorption systems, safety devices, and structural components that need to withstand dynamic loading. A high-strength WMoZrNiFe energetic structural material was prepared, and its mechanical properties and ignition behavior under dynamic loading were studied. Using the split-Hopkinson pressure bar (SHPB) experimental device, samples with different initial tilt angles of 0°, 30°, and 45° were dynamically loaded. The influence of the sample tilt angle on the ignition threshold was analyzed. The dynamic mechanical properties, failure modes, and ignition threshold based on the energy absorption of the WMoZrNiFe energetic structural material during the dynamic loading process were obtained. The results show that the material has a strain rate effect in the range of 1000 s⁻¹~3000 s⁻¹. The yield strength of the sample with a tilt angle of 0° increased from 1468 MPa to 1837 MPa, that of the sample with a tilt angle of 30° increased from 982 MPa to 1053 MPa, and that of the sample with an inclination angle of 45° increased from 420 MPa to 812 MPa. Through EDS elemental analysis, the ignition reaction mechanism of the WMoZrNiFe energetic structural material under dynamic compression was obtained. The violent reaction of the material occurred after the material fractured, and the active elements reacted with oxygen in the air. Full article

The complex burst characteristic parameters of SCB were subjected to dimensionality reduction using principal component analysis (PCA), enabling accurate evaluation of the output performance of SCB. The accuracy and reliability of the PCA method were also validated. A 100 μF tantalum capacitor was utilized to excite the SCB, while a digital oscilloscope recorded the characteristic parameters of the SCB explosion. The experimental results demonstrate that the critical burst time of SCB decreases with the rising voltage, and the critical burst energy decreases first and then increases with the rising voltage. The total burst time and total burst energy of SCB all decrease first and then increase with the rise of voltage. The PCA results indicate that as the voltage increases, the score of SCB output capacity initially decreases and then increases, reaching its lowest point at 17 V. The SCB was utilized to ignite lead styphnate (LTNR) under varying circuit conditions; the characteristic parameters obtained were analyzed using PCA to derive comprehensive scores. The same dataset was then input into the PCA model for pure SCB to calculate corresponding comprehensive scores. The consistency between the two sets of scores validated the accuracy and reliability of PCA in assessing SCB output capability. Full article

As the initial energetic device and driving force of weapon systems, pyrotechnics serve as the core and most sensitive explosive initiating device of weaponry. To accommodate the development requirements of various informatized and miniaturized weapons, MEMS pyrotechnics, characterized primarily by energy conversion informatization, structural miniaturization, and train integration, have become a significant direction in the development of pyrotechnics technology. MEMS Safety and Arming Devices, serving as the energy transfer control mechanisms for micro-explosive trains in MEMS pyrotechnics, are one of the key technologies in the design of MEMS pyrotechnics. This study conducted a classification study of a silicon-based MEMS Safety and Arming Device from the perspective of micro-explosive train structures, analyzed the technical principles of different S&A device, explored their application progress and research status, and summarizes the trends of the micro-miniaturization, integration, and informatization of the silicon-based MEMS Safety and Arming Device, providing new ideas for the research and the design of MEMS Safety and Arming Devices. Full article

A series of modified tetraphenylporphyrins varying only in the electron-donating or electron-withdrawing character of the substituents in the para-phenyl position have been blended into the active layer of MEH-PPV:PCBM bulk heterojunction solar cells. Increasing the electron-withdrawing ability of the substituents, as quantified by the Hammett constant, systematically alters the device efficiency of ternary poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene]:porphyrin:[6,6]-phenylC61-butyric acid methyl ester (MEH-PPV:porphyrin:PCBM) bulk heterojunction organic solar cells through alteration of the HOMO/LUMO levels and, thereby, the open-circuit voltage of the cell. We show that the porphyrin concentrates at the MEH-PPV:PCBM interface in these blends and that the devices operate via a cascade mechanism when the highest occupied molecular orbital (HOMO) of the porphyrin is higher in energy that that of MEH-PPV, but via a parallel/alloy device mechanism, when the HOMO of the porphyrin is lower in energy than that of MEH-PPV. As such, this work highlights how the energetics of the ternary component can determine device performance by switching between charge generation models simply by altering the electron-withdrawing character of the porphyrin ternary additive. Full article

Addressing hazards from dangerous pollutants requires specialized techniques and risk-control strategies, including detection, neutralization and disposal of contaminants. Smart polymers, designed for specific contaminants, provide powerful solutions for hazardous compound challenges. Their remarkable performance capabilities and potential applications present exciting opportunities for further exploration and development in this field. This editorial aims to provide a comprehensive overview of smart materials with unique features and emerging polymeric technologies that are being developed for isolation, screening, removal, and decontamination of hazardous compounds (e.g., heavy metals, pharmaceutically active contaminants, hormones, endocrine-disrupting chemicals, pathogens, and energetic materials). It highlights recent advancements in synthesis methods, characterization, and the applications of molecularly imprinted polymers (MIPs), along with alternative smart polymeric platforms including hydrogels, ion-imprinted composites, screen-printed electrodes, nanoparticles, and nanofibers. MIPs offer highly selective recognition properties, reusability, long-term stability, and low production costs. Various MIP types, including particles and films, are used in applications like sensing/diagnostic devices for hazardous chemicals, biochemicals, pharmaceuticals, and environmental safety. Full article

Energy-harvesting devices utilizing the Vortex-Induced Vibration (VIV) phenomenon are gaining significant research attention due to their potential to generate energy from small water flows, where conventional hydroelectric plants are impractical. Developing effective design methods for these systems is therefore essential. This study focuses on a critical configuration of such devices where energy extraction is achieved by harnessing the oscillatory deformation of two clamped–clamped plates, positioned downstream of the bluff body and subject to the effect of the vortex street. To simplify the preliminary design process, a semi-analytical approach, based on energetic considerations, is proposed to model the non-linear oscillations of the plates, eliminating the need for numerical simulations. The accuracy of this method is assessed through comparative analyses with finite element method (FEM) analyses, under both static and dynamic deformation conditions. The results validate the effectiveness of the proposed approach, offering insights into the effect of the adopted simplifications. In this framework, potential improvements to enhance the method’s reliability are identified. Thus, the work provides a practical model to address the preliminary design of these devices and suggests pathways for its further enhancement. Full article