Search Results (303)

Perfluorosulfonic acid (PFSA) membranes are a key component in many applications, but their low dimensional stability and mechanical strength can result in unsatisfactory device performance and a short life span. To effectively and economically mitigate these limitations with the lowest possible sacrifice of desirable properties, we report herein a PFSA membrane reinforced with a low-cost and easily available polyethylene (PE) mesh fabricated using a simple solution casting method. The high-strength and non-swellable mesh embedded in the PFSA matrix restricts its free swelling. As a result, the reinforced membrane shows a remarkably enhanced dimensional stability, lowering the areal swelling ratio to ~8% in water at 100 °C, in contrast to the ~58% of the unreinforced solution-cast membrane and ~44% of the melt-extruded commercial N117 membrane. Although the non-conductive PE mesh poses certain hindrances to proton transport, the reinforced membranes maintain ~94% of the proton conductivity of the pure PFSA membrane. Moreover, the mechanical strength of the reinforced membrane is enhanced to nearly three times that of the unreinforced one, reaching ~44 MPa. The incorporation of the PE mesh also leads to an enhanced resistance to oxidative corrosion and H₂ gas crossover of the membrane. This research demonstrates a promising technological pathway for developing high-performance and cost-competitive PFSA membranes. Full article

Given the increasing concern around greenhouse gas emissions and the decline in the availability of fossil fuels, there is increasing global demand to develop alternate fuels for maritime transportation that are sustainable and which have lower greenhouse gas emissions. Methanol is one such alternative fuel that has garnered considerable attention given its potential to be produced by more sustainable processes and its more favorable greenhouse gas emission profile in comparison with current fossil fuels. Understanding the physical and chemical properties of methanol under a range of conditions is essential for its development as a marine fuel. In this study, we seek to define physical and chemical properties of different methanol samples to simulate real-world storage conditions as these data are lacking in the literature. Several methanol samples were evaluated: nearly pure methanol; International Organization for Standardization (ISO) marine methanol (MM) grades A, B, and C; and methanol plus higher alcohols. We first evaluated all methanol samples for impurities, acetic acid content, density, and distillation range. We then characterized the effects of water absorption and found that methanol can easily absorb unacceptable water content from humid air within hours, necessitating storage conditions that prevent this process. In eight-week aging experiments at 20 °C and 40 °C in ambient air, we did not observe significant oxidation for any of the methanol samples; however, we did observe increases in acid number. We assessed the impact of contamination of methanol with water, marine gas oil (MGO), and an MGO–biodiesel mixture on density, viscosity, distillation range, and lubricity. Finally, we show that MGO contamination of methanol results in a slight increase in sooting tendency. In aggregate, our results provide an in-depth analysis of physical and chemical properties of methanol as well as the impacts of storage conditions and impurities on the properties of fuel methanol. Full article

To investigate the effects of water-saving irrigation and different straw retention methods on soil CH₄ and N₂O emissions from paddy fields in cold regions and their potential underlying mechanisms, a field experiment was conducted in Qing’an City, Heilongjiang Province. Two water management regimes were set, combined with four straw retention treatments. The static chamber-gas chromatography method was used to monitor CH₄ and N₂O emission fluxes during the entire rice growth period. Meanwhile, soil pH, oxidation–reduction potential (Eh), dissolved oxygen (DO), and dynamic changes in carbon and nitrogen substrates were measured, and the global warming potential (GWP) and greenhouse gas emission intensity (GHGI) were comprehensively evaluated. The results showed that controlled irrigation significantly increased soil dissolved oxygen content and oxidation–reduction potential. Compared with conventional flooding irrigation, total CH₄ emission decreased by more than 50%, while N₂O emission increased by 1.5–2.5 times, exhibiting an obvious divergent correlation with the two gas emission fluxes. Among different straw retention methods, organic fertilizer returning and direct straw returning significantly promoted CH₄ emission by supplying easily decomposable organic carbon. In contrast, biochar, due to its stable carbon structure and favorable pore properties, inhibited CH₄ emission without significantly stimulating N₂O emission. The treatment of controlled irrigation combined with biochar returning (CB) achieved the lowest global warming potential and greenhouse gas emission intensity at 7230.82 kg CO₂-eq/hm² and 0.8054 kg CO₂-eq/kg, respectively, while maintaining high rice yield. Path analysis based on soil physicochemical properties and emission fluxes further revealed that Eh and DO were significantly negatively correlated with CH₄ emission but positively correlated with N₂O emission. Path inference from flux and substrate data indicated that carbon and nitrogen availability were the key factors limiting the denitrification process. In conclusion, the combined application of controlled irrigation and biochar returning can realize the synergistic effect of stable yield and emission reduction in cold-region paddy fields by improving soil aeration and regulating the transformation of carbon and nitrogen substrates, providing a scientific basis for establishing a green and low-carbon rice production technology system for black soil in cold regions. Full article

Background: Evaporative water loss from burn wounds is a major but often neglected component of early fluid requirements. Despite its physiological importance, no dedicated review has quantified acute post-burn evaporative water loss (TEWL) and its interaction with modern resuscitation strategies in over 40 years. Recent mass-casualty burn events in specialized centers have re-emphasized the clinical importance of accurate early fluid balance, which is particularly challenging. Methods: A scoping review (PRISMA-ScR) of historical quantitative studies and 23 contemporary (2015–2025) adult major-burn resuscitation cohorts was conducted. Expected TEWL was derived from Lamke benchmarks; interstitial edema was estimated from the only available regression of simultaneous fluid input and 24 h weight change. A novel TEWL/edema ratio was tested against resuscitation volume (mL/kg/%TBSA) and the established input/output (I/O) ratio. Results: In the acute phase, the median TEWL normalized to total body surface area was 71 mL/m²/h [52–79 mL/m²/h], allowing for calculation of the TEWL/edema ratio. The TEWL/edema ratio was inversely correlated with the resuscitation fluid dose (R² = 0.811) and the I/O ratio as well (R² = 0.86), crossing unity at 2.85 mL/kg/%TBSA. A ratio > 1 signals high evaporative drive and/or possible under-resuscitation; a ratio < 1 alerts to fluid creep before significant weight gain. Conclusions: The TEWL/edema ratio is the first physiology-grounded, easily calculable resuscitation endpoint that complements urine output by providing insight into whether administered fluid is lost as obligatory evaporation or sequestered as edema. Routine estimation of expected TEWL and early monitoring of the TEWL/edema ratio may help guide goal-directed burn resuscitation, especially when early excision is delayed or impossible. Given the substantial inter-individual variability, the ratio derived from aggregate data should not be interpreted as a patient-specific predictor. Full article

Lettuce (Lactuca sativa L.) is a leafy herb that contains many useful nutrients, allowing it to easily overcome the threats to food security in countries of the Global South by adding fiber/bulk, folate and other available nutrients. In 2020, almost 220 metric tons of lettuce was produced in Pakistan. This high production needs attention to meet the demand. Southern Pakistan is facing water crises and the hydroponic system is one revolutionary technique which can allow the region to meet its food demand. In this experiment, different treatment combinations were used to study their effects and evaluate the best combination of nutrients to get the maximum production of lettuce. Results are concluded on the basis of last-week (5th week) production of shoot and root mass. Treatment one (T1) performed outstanding overall out of all four treatments across all parameters. Maximum average root and shoot length (RL, SL) was observed in treatment one (T1) at 5.94 cm and 15.50 cm respectively. Shoot length is directly proportional to production of the head of the plant. For root and shoot weight (RW, SW) treatment 1 (T1) is more effective than treatment 2 (T2). For treatment 1, root weight (RW) was recorded at 0.09 g and shoot weight (SW) was 0.22 g. The hydroponic system demands huge capital investment, which can be compensated by high production of crops. To increase the efficiency of the system, there is a dire need to calculate optimum nutrient combinations for application to the crop for a sound food security plan. Full article

Circular economy (CE) strategies in the agri-food sector hold strong potential for reducing waste, enhancing resource efficiency, and promoting sustainable value creation. However, early-stage assessment of innovative valorisation pathways remains challenging due to limited data availability and heterogeneous sustainability trade-offs. This study presents a multi-criteria evaluation tool designed to identify sustainability hotspots and support the preliminary screening of CE solutions based on easily obtainable information. The tool combines a structured literature review with expert-based scoring across environmental (ENV), economic (EC), and social (SOC) dimensions. Its applicability was demonstrated through the following three case studies: (i) reconstitution of cheese approaching expiration, (ii) extraction of polyphenols from grape-wine residues via subcritical water extraction, and (iii) biodegradable mulching film production from grape-wine pomace. Results show that the tool successfully differentiates sustainability performance across value chain areas Residue, Final Product, and Process (RES, FP, and PRO) and reveals critical gaps requiring further investigation. Scenario 3 achieved the higher overall score (69.7%) due to fewer regulatory constraints, whereas Scenarios 1 and 2 (61.2% and 54.5%, respectively) are penalised due to the more regulations for human consumption. The proposed tool offers a practical and efficient method to support researchers and industry stakeholders in identifying CE strategies with the highest potential for sustainable development. Full article

Biochar is known to enhance soil potassium (K) availability and promote plant K uptake; however, its influence on the transformation pathways of fertilizer potassium and the mechanisms regulating crop potassium accumulation remains insufficiently understood. This study conducted a pot experiment using three soil types—Albic, Brown, and Sandy soils—with different biochar application rates (0, 10, and 20 g·kg⁻¹) in combination with potassium fertilizer, to systematically evaluate the regulation of soil K forms, K fertilizer transformation rates, K use efficiency, and K uptake and accumulation in soybeans. The results demonstrated that the combined application of biochar and K fertilizer significantly increased the contents of available, water-soluble, exchangeable, and non-exchangeable K across all three soils. At the highest biochar application rate (20 g·kg⁻¹), available K increased by 15.37%, 16.78%, and 11.77% in the Albic, Sandy, and Brown soils, respectively, compared to the control. Furthermore, biochar altered the transformation pathways of fertilizer K; it consistently reduced the conversion rate of fertilizer K into exchangeable K across all soils, redirecting it toward the water-soluble and non-exchangeable K pools, thus functioning as a potassium “scheduling center”. Adsorption–desorption experiments revealed that biochar exhibits a strong multilayer adsorption capacity for K ions, with most of the adsorbed K not easily desorbed, providing mechanistic support for the observed shift in transformation pathways. In terms of K use efficiency, biochar reduced the K of agronomic efficiency (KAE) due to a “dilution effect” from its inherent K content. Under the high application rate (20 g·kg⁻¹), the KAE decreased by 11.79% in Albic soil, 88.48% in Sandy soil, and 71.73% in Brown soil, while significantly increasing the partial factor productivity of K (PFPK) and apparent recovery efficiency of K (AREK). Ultimately, the co-application of biochar and K fertilizer significantly enhanced total K accumulation and seed yield in soybeans by increasing K concentrations in various plant parts and promoting dry matter accumulation. At the biochar application rate of 20 g·kg⁻¹, the potassium accumulation and soybean yield under biochar treatment reached maximum increases of 70.77% (in Brown soil) and 42.63% (in Albic soil), respectively. This study demonstrates that biochar can synergistically reduce potassium (K) leaching and improve fertilizer use efficiency by regulating K transformation pathways. This provides a practical guideline for utilizing biochar as a dual-function amendment, which acts as both a supplemental K source and a soil conditioner, thereby supporting the development of more sustainable potassium management practices in diverse cropping systems. Full article

Plastic waste is a global issue due to the popularity of the product. Over time, plastic degrades into smaller particles known as microplastics and becomes harder to deal with as it easily disperses and can be missed by physical catches. Conventional degradation involves environmental forces like ultraviolet (UV) light, water, temperature, and physical abrasion. However, there is increasing interest in microbial plastic degradation, which could positively impact the transformation of (micro)plastics in various environmental matrices. Most of the available research has focused on bacterial degradation, but there is mounting evidence on the impact of fungal degradation. This review discusses conventional and bacterial degradation, then discusses the advantages of fungal involvement in the degradation of microplastics. Biodegradation enhanced by fungal enzymes is a valuable tool that could greatly improve the removal of these microplastic pollutants from the environment. Due to some biochemical complexities, fungi are naturally omnipresent in marine and terrestrial environments under all sorts of climates. Fungi could thrive by themselves or in association with other microorganisms, which could also be applied in non-biotic plastic degradation processes as an alternative to other forms of plastic management in the environment. Full article

Microplastics are contaminants of increasing environmental concern, particularly in marine ecosystems where they can be easily ingested by marine organisms, causing adverse health problems in animals and, through trophic transfer, in humans. While numerous studies have examined microplastic pollution in marine environments, most focus on water, sediment, or biota, thereby only measuring cumulative effects from multiple pollution sources in one area. This review aims to assess existing research on microplastic pollution originating from shipyards and maritime transport activities, with the goal of identifying current knowledge, methodological approaches, and existing research gaps. A review of the scientific literature was conducted, focusing on studies that investigated microplastic pollution associated with shipyards and maritime transport. Priority was given to peer-reviewed publications that included quantitative or qualitative measurements of microplastics. The reviewed literature reveals a limited number of studies explicitly addressing microplastic emissions from shipyards and maritime transport. Available studies employ diverse sampling strategies and analytical methods, making direct comparisons challenging. This review highlights significant gaps in current knowledge regarding microplastic sources and pathways linked to maritime industries. By synthesizing existing data, the paper provides a foundation for future targeted research and supports the development of more effective pollution reduction strategies. Full article

Respirable quartz and dust exposures in dusty façade renovation work tasks were investigated. The presumption was that dust-producing work tasks can be performed safely, keeping exposures low, with practical, easily available methods to control dust emissions and exposure. The aim was to identify deficiencies in exposure management and compare exposure limiting methods to find out how to minimize dust emissions and exposures. Average respirable quartz and dust exposures from the 31 work situations, encompassing nine work tasks studied, were 0.082 and 1.3 mg/m³, respectively. Both values exceed the OEL in Finland, pointing to severe deficiencies in managing exposures. All tasks could, however, be executed safely, keeping exposures low. This often required using respirators while working inside façade covers or close to dust emissions. Other key things when planning exposure maintenance were the following: using water sprays and tool-specific exhausts vents; opening façade cover ventilation apertures; ensuring that non-participants in dusty work tasks are not exposed; working upwind from dust emissions; using pre-blended plaster; using grinders with extension handles; replacing diamond saws and angle grinders with hydraulic cutters when dismantling balcony elements; executing façade jackhammering with robots installed on lifting platforms prior to installing scaffolds and façade covers; detaching façade covers from the clean side; and using lifting platforms. Full article

Soil moisture plays a key role in the critical zone of the Earth and has extensive value in the understanding of hydrological, agricultural, and environmental processes (among others). Long-term (in situ) monitoring of soil moisture measurements is generally not practical; however, short-term measurements are often found. Limited soil moisture measurements can be employed to develop a numerical model for long-term and accurate soil moisture estimations. A key input variable to the model is precipitation, which is also not easily accessible, particularly at a finer spatial resolution; hence, publicly available remote sensing data can be used as an alternative. This study, therefore, aims to develop a numerical model HYDRUS-1D to estimate soil moisture in the data-scarce state of the Northern Territory, Australia, with a land cover of shrubland and a Tropical-Savannah type climate. The HDYRUS-1D is based on the numerical solution of Richards’ equation of variably saturated flow that relies on information about the soil water retention characteristics. This study utilized the van Genuchten model parameters, which were optimized (against measured soil moisture) through parameter optimization with initial estimates obtained from the HYDRUS catalogue. Initial estimates from different sources can differ for the same soil texture (e.g., loamy sand) and can induce uncertainties in the calibrated model. Therefore, a comprehensive uncertainty analysis was conducted to address potential uncertainties in the calibration process. The HYDRUS-1D was calibrated for a period between March 2012 and February 2013 and was independently validated against three different periods between March 2013 and October 2016. Root Mean Square Error (RMSE), Pearson’s correlation coefficient (R), and Mean Absolute Error (MAE) were used to assess the efficiency of the model in simulating the measured soil moisture. The model exhibited good performance in replicating measured soil moisture during calibration (RMSE = 0.00 m³/m³, MAE = 0.005 m³/m³, and R = 0.70), during validation period 1 (RMSE = 0.035 m³/m³ and MAE = 0.023 m³/m³, and R = 0.72), validation period 2 (RMSE = 0.054 m³/m³ and MAE = 0.039 m³/m³, and R = 0.51), and validation period 3 (RMSE = 0.046 m³/m³ and MAE = 0.032 m³/m³, and R = 0.61), respectively. Remotely sensed precipitation data were used from the CHRS-PERSIANN, CHRS-CCS, and CHRS-PDIR-Now to assess their capabilities in estimating soil moisture. Efficiency evaluation metrics and visual assessment revealed that these products underestimated the soil moisture. The CHRS-CCS outperformed other products in terms of overall efficiency (average RMSE of 0.040 m³/m³, average MAE of 0.023 m³/m³, and an average R of 0.68, respectively). An integrated approach based on numerical modelling and remote sensing employed in this study can help understand the long-term dynamics of soil moisture and soil water balance in the Northern Territory, Australia. Full article

We present a stochastic method for classifying high-elevation coniferous forest coverage that includes an uncertainty estimate using Landsat images. We evaluate trends in coniferous coverage from 1986 to 2024 in a sub-basin of the Great Salt Lake basin in the western United States This work was completed before the recent release of the extended National Land Cover Database (NLCD) data, so we use the 9 years of NLCD data previously available over the period from 2001 to 2021 for training and validation. We perform 100 draws of 5130 data points each using stratified sampling from the paired NLCD and Landsat data to generate 100 Random Forest Models. Even though extended NLCD data are available, our model is unique as it is trained on high elevation dense coniferous stands and does not classify wester pinyon (Pinus edulis) or Utah juniper (Juniperus osteosperma) shrub trees as “coniferous”. We apply these models, implemented in Google Earth Engine, to the nearly 40-year Landsat dataset to stochastically classify coniferous forest extent to support trend analysis with uncertainty. Model accuracy for most years is better than 94%, comparable to published NLCD accuracy, though several years had significantly worse results. Coniferous area standard deviations for any given year ranged from 0.379% to 1.17% for 100 realizations. A linear fit from 1985 to 2024 shows an increase of 65% in coniferous coverage over 38 years, though there is variation around the trend. The method can be adapted for other specialized land cover categories and sensors, facilitating long-term environmental monitoring and management while providing uncertainty estimates. The findings support ongoing research forest management impacts on snowpack and water infiltration, as increased coniferous coverage of dense fir and spruce increases interception and sublimation, decreasing infiltration and runoff. NLCD data cannot easily be used for this work in the west, as the pinyon (Pinus edulis) and juniper (Juniperus osteosperma) forests are classified as coniferous, but have much lower impact on interception and sublimation. Full article

With the continuous progress and innovation of petroleum engineering technology, the development of new oilfield additives with superior environmental benefits has attracted widespread attention. Konjac glucomannan (KGM) is a natural resource characterized by abundant availability, low cost, biodegradability, and environmental compatibility. Konjac gum easily forms a weak gel network in water, but its water solubility and thermal stability are poor, and it is easily degraded at high temperatures. Therefore, its application in drilling fluid and fracturing fluid is limited. In this paper, a method of carboxymethyl modification of KGM was developed, and a carboxymethyl group was introduced to adjust KGM’s hydrogel forming ability and stability. Carboxymethylated Konjac glucomannan (CMKG) is a water-soluble anionic polysaccharide derived from natural Konjac glucomannan. By introducing carboxymethyl groups, CMKG overcomes the limitations of the native polymer, such as poor solubility and instability, while retaining its safe and biocompatible nature, making it an effective natural polymer additive for oilfield applications. The results show that when used as a drilling fluid additive, CMKG can form a stable three-dimensional gel network through molecular chain cross-linking, significantly improving the rheological properties of the mud. Its unique gel structure can enhance the encapsulation of clay particles and inhibit clay hydration expansion. When used as a fracturing fluid thickener, the viscosity of the gel system formed by CMKG at 0.6% (w/v) is superior to that of the weak gel system of KGM. The heat resistance/shear resistance tests confirm that the gel structure remains intact under high-temperature and high-shear conditions, meeting the sand-carrying capacity requirements for fracturing operations. The gel-breaking experiment shows that the system can achieve controlled degradation within 300 min, in line with on-site gel-breaking specifications. This modification process not only improves the rheological properties and water solubility of the CMKG gel but also optimizes the gel stability and controlled degradation through molecular structure adjustment. Full article

Water scarcity, driven by over-consumption, population growth, climate change, and pollution, poses severe threats to both human health and ecosystems. Rainwater harvesting (RWH) has emerged as a sustainable solution to mitigate these impacts, offering environmental, social, and economic benefits. Traditional RWH site selection methods rely heavily on GIS-based Multi-Criteria Approaches, such as the Analytical Hierarchy Process, which typically assess runoff potential at the pixel scale using proxy indicators like runoff coefficients or drainage density. However, these methods often overlook horizontal water fluxes and temporal variability, leading to underestimation of the actual runoff available for harvesting. This study introduces an innovative enhancement to AHP/GIS-based methodologies for rainwater harvesting (RWH) site selection by incorporating Aggregated Runoff (AR) as a key criterion. Unlike traditional approaches, the use of AR—representing the total upstream surface water collected at each pixel—enables a more realistic and accurate assessment of RWH potential without increasing data or computational requirements. The proposed criterion is independent of the specific methodology or data layers adopted, making it broadly applicable and easily integrable into existing frameworks. The methodology is applied to the upper Tiber River catchment in Central Italy, demonstrating that AR-based assessments yield more realistic RWH potential maps compared to conventional methods. Additionally, the study proposes a quantile-based scoring system to account for inter-annual hydrological variability, enhancing the robustness of site selection under changing climate conditions. Full article

As a sustainable construction material, mudbrick can be used widely in areas where common modern construction materials are not easily accessible but high clay content soil is available. The inclusion of locally available natural fibres in mudbrick could improve its mechanical and erosion resistance performance. This study examines the performance of fibre-reinforced mudbrick from spinifex and laterite soil which are abundant in Australia. The main objective of this study is to evaluate the mechanical and durability performance of spinifex fibre-reinforced mudbricks made with Australian laterite soil, focusing on the influence of fibre content, fibre length, and cement stabilisation. Spinifex fibre length (30 mm, 40 mm, 50 mm), spinifex fibre percentage (0.3%, 0.6%, 0.9%), and cement percentage (5% and 10%) are considered as the experiment variables. Results show that compressive strength generally decreases with fibre size. In this regard, specimens with 0.3% spinifex fibre, 40 mm fibre length, and 10% cement, with an average compressive strength value of 4.1 MPa, were found to have the highest strength among all design mixes. The elastic Young’s modulus was highest for the specimens with 0.3% spinifex fibre, 30 mm fibre length, and 10% cement with a 36.1 MPa. A low amount of longer fibres was found to be more effective in reducing water absorption in samples with higher cement content. Water absorption and compressive strength results suggest that, on average, 0.3–0.5% spinifex content of size 30 mm improves both low and high cement content mudbricks properties. Full article