Search Results (848)

This work presents a comprehensive analysis of a Palladium (Pd)-gated graphene nanoribbon field-effect transistor (GNRFET) as a high-sensitivity potential hydrogen sensor under idealized conditions, focusing on the structural and environmental control of multimetric sensitivity. Hydrogen adsorption is modeled through pressure-dependent work-function modulation and interface coverage, including competition with oxygen. For hydrogen gas at a pressure of $P_{{\mathrm{H}}_2}={10}^{-6}$ Torr without O₂, the sensor exhibits a maximum threshold voltage sensitivity of about 300 mV, which is reduced to roughly 40 mV under an oxygen partial pressure of 152 Torr, quantifying the impact of background gas on response. Band diagrams, transmission spectra, local density of states, and transfer characteristics are examined over wide ranges of H₂ pressure, temperature, gate length, and nanoribbon width. Sensitivity is evaluated using drain current change, threshold voltage shift, and average subthreshold swing variation. Results showed that the sensitivity based on current is high for ultralow hydrogen pressures, whereas it is low in higher levels of pressure compared to the sensitivity based on subthreshold. Also, uncertainty analysis revealed that the threshold voltage metric remains largely geometry-independent and thus tolerant to fabrication variations. Full article

Extreme combustion features strong unsteadiness, heterogeneity and multi-physics coupling, which is of great significance for advanced propulsion systems. High-performance sensing of such extreme combustion flow fields is critical to revealing physical mechanisms and capturing fine flow structures. However, it faces severe challenges: rich multi-band spectral characteristics require multi-spectral observation; ultra-transient processes demand high-frequency imaging; and high-performance photoelectric enhancement is necessary under short gate width and high frame rates. To solve these problems, this study developed a high-performance ultraviolet optical sensing system (HUOSS), which achieves megahertz-level imaging at a 1608 × 1104 full-frame resolution and provides a 10⁷ electron gain in the ultraviolet band. The HUOSS has been applied to chemiluminescence sensing of a hydrogen/ammonia-air rotating detonation as a representative extreme combustion system. Based on the analysis of representative influencing factors (e.g., the transmission characteristic of the bandpass filter and the intensifier gate width) in the HUOSS, the filter transmission loss and its influence on the gate width settings have been revealed. From the chemiluminescence sensing images captured in the experiments, the fine structure and evolution of detonation waves have been clearly identified, verifying the high-speed imaging capability. Furthermore, simultaneous OH* and NH* multi-spectral observation has been realized, and the effects of ammonia addition have been analyzed, validating the multi-spectral diagnostic capacity of the system. This study provides an effective diagnostic method for extreme transient combustion research, and comprehensively verified the multi-spectral, extremely transient and high signal-to-noise ratio sensing capabilities of this system. Full article

The systematic influence of signal electrode width on electro-optic bandwidth and insertion loss in L-type traveling-wave lithium niobate modulators has not yet been comprehensively quantified, limiting the parametric engineering design of this device configuration. This study presents a full-band systematic simulation sweep of signal electrode width and three auxiliary geometric parameters in an L-type traveling-wave lithium niobate Mach–Zehnder modulator, combined with optical mode simulation to establish joint microwave–optical optimization constraints. The study reveals the coupled modulating effect of signal electrode width on characteristic impedance, velocity mismatch, and transmission loss; it elucidates the competition mechanism underlying non-monotonic high-frequency loss behavior; and it identifies the complete impedance-neutral characteristic of the electrode–waveguide contact width as an independent loss-tuning degree of freedom decoupled from the impedance constraint. Full-system validation confirms that the final design simultaneously satisfies broadband impedance matching, low insertion loss, and high electro-optic bandwidth. The results are distilled into four quantitative design rules that provide simulation-driven guidance directly applicable to the engineering design of L-type thin-film lithium niobate modulators, advancing the systematic establishment of a parametric design methodology for this device configuration. Full article

To explore the strong coupling between surface phonon polaritons (SPhPs) and quantum dots in one-dimensional periodic microstructures for quantum information processing, we establish a comprehensive theoretical model for SPhPs at air–polar dielectric interfaces. By rigorously deriving the dispersion relations, we reveal the decisive role of scale effects on bandgap formation: continuous spectra without bandgaps emerge at the nanoscale ($d\sim 10$–100 nm), whereas periodic modulation induces significant Bloch mode folding and tunable bandgaps (0.5–5 $\mathsf{\mu }\mathrm{m}$ width) at the microscale ($d\sim 1$–10 $\mathsf{\mu }\mathrm{m}$). Based on Fourier bandwidth limitations, we determine optimal channel widths ($L_y\ge 10 \mathsf{\mu }\mathrm{m}$) for maintaining low-loss modes with energy deviations below 1%. Through electromagnetic field quantization, we obtain analytical expressions for SPhP mode amplitudes and quantum dot transition rates. Calculations demonstrate that in micrometer-scale CsI structures, spontaneous emission rates can be modulated significantly: suppressed to <0.1 times the free-space values within bandgaps (excited-state lifetimes extended to ∼10 ns) and enhanced 5–8 times at conduction band edges. Leveraging these characteristics, we propose a scheme for batch quantum state manipulation of ${10}^2$–${10}^3$ arrayed quantum dots via selective excitation of specific Bloch modes using controlled laser frequency and angle, enabling parallel single-qubit gates with theoretical fidelity > 99%. Compared with surface plasmon polariton schemes, our approach utilizes the low-loss infrared characteristics of SPhPs ($Q\sim 100$–1000, 1–2 orders higher) to reduce decoherence rates, offering a new pathway for room-temperature solid-state quantum computing and on-chip multi-node entanglement distribution. Full article

The paper presents an optimisation workflow for modelling of a periodic mechanical structure in the form of a multi-material, axisymmetric beam. The optimisation objective is to prescribe the positions and widths of selected band gaps within a target frequency range for three basic types of structural vibrations: flexural, longitudinal and torsional. The decision variables were geometric parameters of the unit cell and material properties of selected thermoplastics assigned to successive segments of the cell. The frequency characteristics of the beam were determined using the time-domain spectral finite-element method (TD-SFEM). This model was used to perform a sensitivity analysis using the Morris method, which showed the dominant influence of the beam geometry on the position and width of band gaps, with a relatively smaller role of material variability. Due to high computational costs of the global optimisation based on a FEM solver, a surrogate regression model in the form of a residual MLP network was developed to predict the positions and widths of the first five band gaps for each vibration type. The global search was carried out using a genetic algorithm (GA) with the surrogate model and then the results were refined using a deterministic goal-attainment method with a high-fidelity model. Full article

The band saw blade is distinguished by its multi-point and flexible cutting capability when sawing materials. Its wear form is significantly more intricate than that of traditional cutting tools, such as the lathe tool and the milling cutter. Preliminary experimental observations suggest a close correlation between the wear of band saw blades and the motor current of the driving wheel. Therefore, this study evaluates the wear condition of band saw blades using current signals. A mathematical correlation model was established between the driving wheel motor current signals and the load on the band saw. A comprehensive experimental study was conducted on the band saw blade, encompassing the entire lifecycle of sawing operations. The average wear width of the tooth tip was utilized as an indicator of tooth wear, and an investigation was conducted into the correlation between the driving wheel motor current signals and the wear state. The findings indicated that the driving wheel motor current signals could be utilized to assess the blade wear state with high precision, which would facilitate proactive maintenance and replacement strategies to optimize band saw performance and service life. Full article

In this paper, we present a study on the automated design optimization of a wideband low-noise amplifier (LNA) operating in Ku-band (12 to 18 GHz) using proximal policy optimization (PPO), one of the widely applied reinforcement learning (RL) algorithms for engineering problems. As a target microwave active circuit, we select a two-stage LNA architecture, where transmission lines (TLs) are dominantly used for impedance matching and gain/noise optimization. For simplicity, all widths of TLs were fixed so that the characteristic impedance is 50 Ω, with lengths of TLs being set as design parameters. In addition, dimension variables of capacitors were treated as design parameters and, in total, we optimized 29 parameters. For target specifications, we set both $S_{11}$ and $S_{22}$ to be below −10 dB over the 12–18 GHz band and the noise figure (NF) to be below 2 dB. A total of 20,140 simulations were performed for training and the overall process took about 24 h. The results show that both the reward and the loss converged appropriately, achieving the target specifications successfully. For the final results, we performed up to 25 predictions, and the prediction process was terminated early if a solution meeting all target specifications was found within the given number of attempts. The device model used was a commercial 150 nm GaN high-electron-mobility transistor (HEMT) process technology. Full article

The rapid inspection of urban road hazards, such as subsurface voids and pipeline damage, demands high efficiency and precision in detection technology. Conventional Ground Penetrating Radar (GPR) systems often face limitations in urban environments, including slow survey speeds, poor channel scalability, and the trade-off between shallow resolution and deep penetration. The proposed system integrates a dual-band antenna array (200 MHz and 400 MHz) to resolve the classical resolution–penetration trade-off, simultaneously capturing high-resolution shallow data and achieving deep subsurface penetration in a single pass. To overcome the sampling rate bottleneck inherent in low-cost microcontrollers, a custom Time-Division Step Multiplexing (TDSM) protocol extends the equivalent sampling period to 0.38 µs across 24 parallel channels while maintaining a 200 kHz pulse repetition rate—enabling real-time data streaming at vehicle speeds up to 70 km/h with 5 cm trace spacing. This capability directly addresses the critical challenge of traffic disruption on urban arterials caused by conventional slow-speed GPR surveys. Complementing this, a master-slave FPGA-MCU hierarchical architecture provides seamless channel scalability from 24 to 36 channels, adapting to diverse swath width requirements without hardware redesign. Laboratory physics model experiments demonstrate a penetration depth exceeding 3 m after convolutional sparse fusion of the dual-band data, covering the typical burial depth of urban utilities. This study provides a deployable high-resolution underground detection solution for rapid urban infrastructure surveys and emergency disease detection by breaking the traditional constraints of channel number, sampling rate, and detection speed, significantly reducing interference with urban main traffic. Full article

We formulate the Quantum Information Copy Time (QICT) framework for conserved charges under strictly local quantum dynamics and isolate its logically strongest consequence. The theorem-level core is a receiver-optimised variational speed-limit inequality: after projection away from the conserved zero mode, the copy time is bounded from below by the inverse square root of a Liouvillian-squared receiver susceptibility times a local encoding seminorm. This statement is written in a finite-volume operator framework and does not require a diffusive ansatz. We then examine what follows only after additional infrared assumptions. Under a single diffusive slow-mode hypothesis, the variational inequality reduces to the practical scaling relation used in the benchmark computations. That reduction is treated as conditional and is stress-tested numerically rather than promoted by rhetoric. Within the anomaly-free Abelian span relevant for one Standard-Model-like generation, hypercharge selection is elevated to theorem-level status; by contrast, minimal gauge-algebra uniqueness remains explicitly conditional on additional model-selection axioms. The remainder of the manuscript is organised as an explicitly documented closure programme built on top of this core. In that closure, a gauge-coded QCA construction, a microscopic benchmark for the transport normalisation, and an electroweak matching convention are combined to produce a resonance-centred Higgs-portal singlet-scalar mass band together with direct-detection, invisible-width, and relic-consistency checks. These latter results are presented as model-dependent consequences of an explicit closure ansatz rather than as deductions from locality alone. Full article

To address the difficulty of directionally cutting thick, hard key strata in gob-side entry retaining using conventional blasting or hydraulic fracturing, this paper proposes a high-pressure water-jet slotting-induced pre-cracked weakening belt (PCWB) roof-cutting technology. Several finite-length PCWBs are arranged within the key stratum and designed to coalesce into a plane, inducing through-going roof failure along a pre-determined path. A fixed–fixed key strata beam model combined with linear elastic fracture mechanics shows that the double-belt configuration forces the bending moment and shear force to concentrate in a thin rock bridge, where bending and shear stresses are amplified by about 1.5–2.8 times and 1.2–1.7 times, respectively, for 2–4 m thick key strata, providing a mechanical basis for preferential tensile–shear failure. Two-dimensional RFPA2D simulations reveal “width-dominated, length-assisted” control of cutting performance and identify an optimal weakening belt geometry of about 400 mm in width and 200 mm in length. Three-dimensional numerical modeling of parallel slot pairs indicates that intra-pair spacing of about 40 mm produces a continuous, directional weakening belt, whereas smaller or larger spacing causes, respectively, destructive interference or loss of connectivity. High-pressure water-jet tests (320 MPa, 0.33 mm nozzle, 1.30 mm/s traverse speed) on limestone blocks confirm that single slots can penetrate the full thickness and that cracks from adjacent slots coalesce through the rock bridge, forming a wide, straight fracture band. Field application in the Dongjiang Mine (3.5 m limestone key stratum, ~400 m depth) shows that the first weighting is advanced from the 7th to the 3rd day, peak support resistance is reduced from 8.8 to 7.4 MPa, and periodic weighting becomes more frequent and smoother. The PCWB technology is therefore suitable for panels with 2–4 m thick hard key strata at similar depths, offering precise key stratum severance, active stress relief, and safe, controllable construction. Full article

The 795 nm wavelength corresponds to the D1 transition of rubidium atoms and is widely used in atomic optical pumping, atomic clocks, magnetometers, and precision spectroscopy. For compact free-space collimation, beam shaping, and efficient fiber coupling, edge-emitting semiconductor lasers with reduced fast-axis (vertical) divergence are highly desirable, yet low-divergence designs at 795 nm remain limited. Here, we propose and demonstrate low-divergence photonic-crystal epitaxy (LD–PC) for 795 nm edge-emitting lasers. By engineering a periodic n-side photonic-crystal stack to place the fundamental vertical mode near the photonic band edge, the vertical mode is expanded while maintaining effective modal discrimination. Narrow-ridge Fabry–Pérot lasers based on GaAsP/AlGaAs single-quantum-well epitaxy were fabricated and characterized. The optimized LD–PC device (3 μm ridge width, 1 mm cavity length) delivers 227 mW at 200 mA with a threshold current of 23 mA, a slope efficiency of 1.28 W/A, and a peak wall-plug efficiency of 55% under continuous-wave operation at 25 °C. The measured far-field divergences (FWHMs) are 7.16° and 18.83° in the lateral and vertical directions, respectively, corresponding to a reduction in the vertical divergence from >40° in the reference structure to <20° with LD–PC. These results validate photonic-crystal epitaxy as an effective route toward compact, high-performance, low-divergence 795 nm semiconductor laser sources for rubidium-based atomic systems. Full article

We present an innovative, cost-effective framework integrating laboratory Hyperspectral Imaging (HSI) of the Bechar 010 Lunar meteorite with ground-based lunar HSI and supervised Machine Learning (ML) to generate high-fidelity mineralogical maps. A 3 mm thin section of Bechar 010 was imaged under a microscope with a 30 mm focal length lens at 150 mm working distance, using 6x binning to increase the signal-to-noise ratio, producing a data cube (X × Y × $\lambda$ = $791\times 1024\times 224$, $0.24$ mm × $0.2$ mm resolution) across 400 nm to 1000 nm (224 bands, $2.7$ nm spectral sampling, $5.5$ nm full width at half maximum spectral resolution) using a Specim FX10 camera. Ground-based lunar HSI was captured with a Celestron 8SE telescope (3 km/pixel), yielded a data cube ($371\times 1024\times 224$). Solar calibration was performed using a Spectralon reference (99% reflectance < 2% error) ensured accurate reflectance spectra. A Support Vector Machine (SVM) with a radial basis function kernel, trained on expert-labeled spectra, achieved 93.7% classification accuracy (5-fold cross-validation) for olivine (92% precision, 90% recall) and pyroxene (88% precision, 86% recall) in Bechar 010. LIME analysis identified key wavelengths (e.g., 485 nm, 22.4% for M3; 715 nm, 20.6% for M6) across 10 pre-selected regions (M1 to M10), indicating olivine-rich (Highland-like) and pyroxene-rich (Mare-like) compositions. SAM analysis revealed angles from $0.26$ rad to $0.66$ rad, linking M3 and M9 to Highlands and M6 and M10 to Mares. K-means clustering of Lunar data identified 10 mineralogical clusters (88% accuracy), validated against Chandrayaan-1 Moon mineralogy Mapper (${\mathrm{M}}^3$) data (140 m/pixel, 10 nm spectral resolution). A novel push-broom HSI approach with a telescope achieves 0.8 arcsec resolution for lunar spectroscopy, inspiring full-sky multi-object spectral mapping. Full article

One of the strongest electromagnetic engineering approaches for enhancing antenna performance is the use of photonic crystal (PhC) substrates. This technique can be efficiently applied to antenna design and offers notable advantages, such as gain improvement, increased bandwidth, and frequency-dependent beam scanning. In this paper, a bow-tie dipole antenna has been developed for terahertz operation over the 0.39–1.3 THz band, presenting a novel structure capable of producing strong ultra-wideband (UWB) field enhancement within its feed gap. The feed gap between the two metallic arms has a slot width of 1.24 λ0 (λ0 is the wavelength in free space at a center range of 0.8 THz), which facilitates the generation of an enhanced electric field. The PhC substrate enables surface-wave control through dispersion engineering, thereby enhancing the radiation efficiency of the antenna. The proposed antenna exhibits a radiation efficiency of approximately 73–93% over the entire UWB frequency band. Furthermore, the PhC substrate antenna achieves a maximum gain of 21 dB, exceeding that of a homogeneous-substrate THz bow-tie antenna by at least 3.3 dB. The results indicate that the antenna achieves |S₁₁| < −10 dB impedance matching over the bandwidth of 105.9%, ranging from 0.4 to 1.3 THz. The proposed bow-tie dipole antenna integrated with a PhC substrate demonstrates a wide beam-scanning capability from −54° to +74° across the 0.39–1.16 THz band, while maintaining a compact footprint of 14.9 λ₀ × 22.4 λ₀. This combination of wide scanning, broad bandwidth, and ultra-low profile represents a notable advancement in the development of compact THz radiating structures. Full article

A novel catalyst, Tm₂FeSbO₇, was synthesized by employing the solid-phase high-temperature sintering method, and, for the first time, it was utilized to create a Z-type heterojunction with BiYO₃. A direct Z-scheme Tm₂FeSbO₇/BiYO₃ heterojunction photocatalyst (TBHP) was successfully produced by employing the ball-milling technique. X-ray diffraction analysis results indicated that Tm₂FeSbO₇ crystallized in a cubic pyrochlorestructure which owned the Fd-3m space group, with a unit cell parameter of 10.1769 Å, whereas BiYO₃ displayed a fluorite structure in the Fm-3m space group, with a unit cell parameter of 5.4222 Å. The Mossbauer spectrum of Tm₂FeSbO₇ showed that Fe³⁺ ions might locate at octahedral sites. The measured bandgap widths for the TBHP, Tm₂FeSbO_7, and BiYO₃ were 2.14 eV, 2.21 eV, and 2.30 eV, respectively. Multiple experimental results demonstrated that the TBHP exhibited a higher valence band ionization potential, a narrower band gap width, and a higher removal efficiency of the sulfamethoxazole (SMX) compared with the Dy₂TmSbO₇/BiHoO₃ heterojunction photocatalyst. Under visible-light irradiation (VISLI) of 115 min, the TBHP showcased exceptional photocatalytic elimination performance; therefore, the elimination rate of the SMX and the total organic carbon (TOC) mineralization rate reached 99.51% and 98.10%, respectively. In contrast to single-component Tm₂FeSbO₇, BiYO_3, or conventional nitrogen-doped titanium dioxide (N-TiO₂) catalyst, the TBHP exhibited removal efficiency enhancement for degrading the SMX by 1.17 times, 1.31 times, or 4.06 times. Simultaneously, the matching mineralization rate for removing the TOC density by employing the TBHP was 1.20 times, 1.34 times, or 4.73 times higher than that by employing Tm₂FeSbO₇, BiYO₃, or conventional N-TiO₂. Above experimental results indicated that the mineralization efficiency for removing TOC density by employing the TBHP was higher than that by employing Tm₂FeSbO₇, BiYO₃, or N-TiO₂. Radicals trapping experiments and the electron paramagnetic resonance spectroscopy results revealed that hydroxyl radicals, superoxide anions, and photoinduced holes were the primary active species during the catalytic elimination course of the SMX by employing the TBHP under VISLI. The results demonstrated that the direct Z-scheme TBHP, which was developed in this study, exhibited the maximal removal efficiency for degrading the SMX in contrast to Tm₂FeSbO₇, BiYO₃, or N-TiO₂. Additionally, the possible elimination routes and elimination mechanisms of the SMX were proposed. Therefore, an important scientific foundation for developing high-performance heterojunction catalysts was established. Full article

The runner of a pump turbine features a relatively flat structural configuration. The clearance cavities formed between the upper crown, lower band, and surrounding stationary components play a critical role in its dynamic behavior and operational stability. Consequently, a detailed modal analysis of the runner is essential to ensure safe and stable operation. In this study, an acoustic–structure coupling method is adopted to investigate the wet modal characteristics of the pump-turbine runner, explicitly accounting for the added mass effect induced by the fluid in the external flow passages. By systematically varying the geometric parameters of the upper crown clearance cavity, the influence of seal clearance dimensions on the runner’s modal characteristics is examined. The results demonstrate that the radial clearance and the axial height of the seal cavity are the most influential parameters, reducing natural frequencies by up to 15.85% and 16.93%, respectively. The pitch of the seal teeth shows a secondary yet notable effect, inducing a frequency variation of 13.73%. In contrast, local labyrinth seal parameters, such as the number of teeth and tooth width, have a comparatively limited effect. This study provides practical guidance for vibration risk prediction, anti-resonance design, and operational stability assessment of high-head, large-capacity turbine runners by revealing the quantitative relationship between geometric parameters and modal frequencies. Full article