Search Results (84)

The mixing valve is a key component of an ultra-high-pressure premixed abrasive waterjet system, in which the abrasive–water mixing uniformity plays a decisive role in determining the erosion and cutting performance of the jet. The geometric parameters of the mixing chamber inside the valve are therefore critical factors affecting this uniformity. In this study, the liquid–solid two-phase flow within the mixing chamber was numerically investigated using the Eulerian k–ε turbulence model coupled with the Fluent–Rocky DEM approach. Single-factor simulations were first conducted to identify the effective ranges of key structural parameters influencing the mixing performance. Subsequently, a response surface model was established to describe the relationship between the mixing efficiency (ME) and four critical chamber parameters, namely the throat diameter (TD), throat length (TL), abrasive inlet pipe diameter (AD), and the distance between the throat exit and the abrasive inlet pipe center (TE). Based on this model, the optimal structural parameters of the mixing chamber were determined. The results indicate that when TD = 4 mm, TL = 12 mm, AD = 10 mm, and TE = 7 mm, the simulated ME reaches 34.40% ± 0.49%, which is in close agreement with the predicted value of 34.57%. Experimental validation conducted on a premixed abrasive waterjet test rig shows that the mean absolute relative error between the simulated and measured ME values is 7.54%, which is below the 10% threshold, confirming the reliability and accuracy of the numerical model. Full article

Rotary abrasive waterjet (AWJ) cutting is an effective technique for industrial tube cutting and is widely used for oil and gas well tubing. This study presents a self-designed experimental apparatus for investigating the cutting performance of rotary AWJ. Based on the SPH-FEM coupling theory, a numerical model for rotary AWJ cutting of tubing was developed to investigate the cutting mechanism and optimize process parameters. Experimental results show that low peripheral speed leads to inefficient utilization of jet energy, whereas excessively high peripheral speed degrades cutting performance; the optimal range is 5.65–7.54 mm/s. Pump pressure below the cutting threshold or high pressure both decrease cutting efficiency, with optimal performance at 50 MPa. Both overly fine and overly coarse abrasive mesh sizes degrade cutting performance, with 80-mesh abrasive being optimal. Increasing standoff distance intensifies jet energy attenuation, decreases cutting capacity, and increases kerf taper; 8.5 mm is recommended. Cutting depth increases over cutting time until the jet no longer has enough energy to cut, at which point the depth stops increasing. A theoretical basis for the design and application of rotary AWJ cutting technology in oil and gas wells is provided in this study. Full article

The agriculture and food processing sectors are essential, meeting the fundamental needs of global populations. However, it is crucial to adopt sustainable practices that fulfill these needs while minimizing environmental impact. Climate change, once a theoretical concern, is now an urgent and tangible challenge, requiring immediate action to mitigate its effects. As such, all human activities, particularly those in resource-intensive sectors like agriculture, must be reevaluated. This study explores and reviews the potential of applying waterjet systems and their evolution in agricultural and food processes to improve efficiency and minimize resource consumption; while the use of pure waterjet technology for soft foods has emerged as an established practice, its extension to agricultural applications and the use of abrasive waterjet in this field are still in the research and experimentation phase. This work presents preliminary results, discussing the key waterjet components, their economical modeling, and food safety. Three main categories of applications—cutting of soft, plant-based products, cutting of animal products, and in-field agricultural applications—are reviewed, with detailed use cases on strawberry de-calyxing, meat–bone cutting and sugarcane harvesting, respectively. These applications are analyzed by highlighting waterjet main advantages in terms of cutting performance, as well as food quality and preservation. At the end, future directions are delineated, suggesting potential advancements that could allow us to replace traditional methods with more innovative and sustainable alternatives. A specific focus is given to abrasive ice waterjets. Full article

Abrasive waterjet machining (AWJM) is widely used for cutting aerospace aluminum alloys, but exit-side defects associated with jet lag can degrade surface integrity and dimensional accuracy. This work investigates the influence of water pressure, abrasive mass flow rate, and traverse feed rate on the formation of jet-lag defects at the exit side of cuts in UNS A92024 aluminum alloy plates of 10 mm thickness. A full factorial 3³ experimental design was implemented to manufacture 27 square samples (20 × 20 mm), which were subsequently characterized by optical microscopy at 20× magnification. The semicircular jet-lag defects were quantified using Imaging processing techniques to determine their projected area, and the resulting data were analyzed with multifactor ANOVA and multiple linear regression. The results show that traverse feed rate and water pressure have a statistically significant effect on defect area, with traverse feed rate being the most influential factor, whereas the abrasive mass flow rate plays a secondary role within the investigated range. Combinations of high water pressure and low traverse feed rate led to cleaner cuts with reduced exit-side damage, and contour plots allowed the identification of operational windows that minimize defect formation. The proposed methodology provides a systematic framework for characterizing jet-lag defects in AWJM and can be extended to other alloys, thicknesses, and advanced characterization techniques to support process optimization in industrial applications. Full article

In this study, Delrin^® (POM) polymer was reinforced with 15 wt.% chopped ramie fiber (RF) to develop a sustainable composite, which was injection-molded and machined using abrasive waterjet machining (AWJM). SEM revealed a skin-core morphology with flow-induced RF alignment and small voids at bundle crossovers, indicating interfacial adhesion. A Taguchi L₉ (3³) design evaluated waterjet pressure (WJP: 100–300 MPa), traverse speed (TS: 100–200 mm/min), and stand-off distance (SoD: 1–3 mm) on kerf width (KW) and surface roughness (SR). Increasing WJP from 100 to 300 MPa lowered mean SR from 6.23 to 4.80 µm (23% reduction) and KW from 1.31 to 1.07 mm (reduction of 18%); enlarging SoD from 1 to 3 mm raised SR from 4.98 to 5.55 µm (an 11% increase) and KW from 1.12 to 1.20 mm (a of 7% increase); and raising TS from 100 to 200 mm/min narrowed KW from 1.24 to 1.11 mm (a 10.5% reduction) with a modest SR decrease from 5.45 to 5.28 µm. ANOVA confirmed WJP as the dominant factor for SR (79.8%), as well as a significant SoD (18.3%). For KW, the influence of WJP (68.8%) was substantial, followed by TS (19.9%) and SoD (11%). Linear models captured the trends well (SR: R² = 88.29%; KW: R² = 93.36%). A desirability-based multi-response optimizer yielded ideal conditions for TS (200 mm/min), WJP (300 MPa), and SoD (1 mm), predicting a KW of 0.94 mm and an SR of 4.1567 µm. Confirmation tests produced a KW (0.970 ± 0.01 mm) and SR (4.27 ± 0.05 µm), which are within 3.19% and 2.73% of the predicted values, validating the DoE regression approach. Full article

Additively manufactured stainless steels are gaining considerable attention in the production of complex components, especially in the aerospace, food production, energy, and biomedical industries. Machining and achieving the desired surface properties of such materials remains a challenge. Abrasive waterjet machining technology appears to be one of the options due to the advantages it brings. Removing support structures and separating individual parts is also one of the possible applications of this technology. This study investigates the effects of process parameters for individual cut qualities (Q1–Q5) of abrasive waterjet on the surface properties of additively manufactured stainless steel (SS 316L) specimens, considering the different mechanical properties of the material due to the direction of layering of the material during its production. Experimental specimens were prepared by selective laser melting technology with parameters ensuring the best possible quality of the resulting part. The results of the study showed changes in the topography of the machined surface, especially in the roughness parameters. Scanning Electron Microscopy and Energy Dispersive X-ray Spectroscopy analysis proved the presence of fragmented abrasive particles in the cut areas. Full article

Due to recent developments across the aerospace, power generation and defense sectors, the demand for flat-surfaced components with extremely high surface quality is rapidly increasing. In this regard, although abrasive machining processes often produce fine, contaminated swarf that is frequently relegated to landfill, these processes remain critical for the engineering sector. Motivated by increasing sustainability and circularity pressures, this narrative review examines the current state of the art in recycling and repurposing the chips, tooling and cutting fluids that are typically generated or consumed within grinding processes. In doing so, a number of methodologies for extracting useful materials from swarf slurries are identified, including pyrometallurgical routes (applied successfully to Ni–Co alloys, for example), hydrometallurgical strategies (e.g., iron leaching from ferrous swarf) and, in the case of non-metallic materials such as CMCs and CFRPs, chemical processing methods. Various means of separating abrasive constituents and removing contaminants from grinding swarf are also highlighted, within which centrifugation and heat treatment are found to be particularly useful for non-ferrous materials such as titanium alloys or composites, whilst ferrous materials are largely magnetically separated. Prospective applications for spent abrasive tooling are also explored, including reuse as shot, waterjet machining feedstock, road surface additives, or mortar in the context of cement production. Likewise, heat- and radiation-based strategies for prolonging cutting-fluid life are highlighted, and their associated sustainability benefits and limitations discussed, despite ultimate disposal still being relegated to fuel usage or landfill. Ultimately, this review identifies the scarcity of grinding-specific recycling process data and highlights the need for robust, publicly accessible recycling strategies for novel material systems. Full article

Spent garnet (SG) wastes are generated in significant quantities by several industrial activities, including abrasive waterjet cutting (AWJ), abrasive blasting, and filtration and powdered media applications. These wastes represent a promising secondary raw material for the production of sustainable construction materials, particularly green mortars and concretes, through their partial replacement of natural sand in cementitious systems. Such applications are relevant to both hydraulically setting inorganic binders (cement-based materials) and alkali-activated cementitious materials (AACMs). The valorization of SG wastes offers multiple benefits, notably a dual environmental advantage: reducing the consumption of natural aggregates and diverting industrial waste from disposal by integrating it into a new life cycle as a value-added by-product. Additional potential advantages include reduced production costs and possible improvements in the overall performance of mortars and concretes. Despite these benefits, the use of SG as an aggregate replacement remains insufficiently explored, with existing studies providing only preliminary and fragmented evidence of its feasibility. This paper presents an overview of a comprehensive four-year research program investigating SG wastes derived from single-cycle AWJ processes and their incorporation into conventional mortars as partial fine aggregate replacement in cement-based construction composites. The validation stage of the performance assessment expands the range of SG sources by including new sampling from the original suppliers, enabling verification of the repeatability and reproducibility of earlier findings. A broad set of physical, mechanical, and durability properties—particularly resistance to freeze–thaw cycles—is evaluated to achieve a robust and comprehensive material characterization. These results are further correlated with chemical and microstructural analyses, providing critical insights to support the technological transfer of SG-based construction materials to industrial applications with reduced carbon footprint. Full article

This research proposes an intelligent modeling and optimization strategy for abrasive waterjet machining (AWJM) of magnesium-based fiber metal laminates (FMLs) reinforced with reduced graphene oxide (r-GO). Experiments were designed using the Box–Behnken method, considering waterjet pressure, stand-off distance, traverse speed, and r-GO content as inputs, while kerf taper (Kt), surface roughness (Ra), and material removal rate (MRR) were evaluated as outputs. Adaptive Neuro-Fuzzy Inference System (ANFIS) models were developed for each response, with their critical optimized hyperparameters such as cluster radius, quash factor, and training data split through the dragonfly optimization (DFO) algorithm. The optimized ANFIS networks yielded a high predictive accuracy, with low RMSE and MAPE values and close agreement between predicted and measured results. Four metaheuristic algorithms including particle swarm optimization (PSO), salp swarm optimization (SSO), whale optimization algorithm (WOA), and the antlion optimizer (ALO) were applied for simultaneous optimization, using a TOPSIS-based single-objective formulation. ALO outperformed the others, identifying 325 MPa waterjet pressure, 2.5 mm stand-off, 800 mm/min traverse speed, and 0.00602 wt% r-GO addition in FMLs as optimal conditions. These settings produced a kerf taper of 2.595°, surface roughness of 8.9897 µm, and material removal rate of 138.13 g/min. The proposed ANFIS-ALO framework demonstrates strong potential for achieving precision and productivity in AWJM of hybrid laminates. Full article

The natural fiber-reinforced nanomaterial filler polymer matrix hybrid composite has superior applications in industrial and manufacturing fields due to its enhanced mechanical and machinability characteristics. However, in order to generate high-quality components, unconventional machining techniques, notably abrasive waterjet machining, have become more popular due to the inhomogeneity of composites, fiber pullout, greater surface roughness, and dimensional inaccuracy under traditional machining. Delamination typically refers to the separation that occurs along a plane parallel to the surface, such as the detachment of a coating from its underlying material or the separation between different layers within the coating itself. This paper investigates the AWJM characteristics of Hibiscus Rosa-Sinensis/Carbon nanotube/Epoxy (HRSCE)-based hybrid composite, focusing on delamination factors at entry, exit, and machining time. An L₂₇ orthogonal array was employed to optimize process parameters, revealing that DF-entry decreased with increasing CNT (wt.%), achieving its lowest values at 3 (wt.%) CNT and 2 mm stand-off distance due to enhanced composite toughness and precise jet focus. Conversely, DF-exit increased with higher CNT (wt.%), stand-off distance and traverse speed, attributed to the composite’s increased brittleness and reduced cutting efficiency. Machining time was predominantly influenced by CNT (wt.%) (92.4%), increasing with higher reinforcement levels due to enhanced material resistance. Response surface methodology models demonstrated high accuracy in predicting machining outcomes, with errors below 3%. Contour and surface plots identified optimal conditions for minimal delamination and machining time as 3 (wt.%) CNT, low stand-off distance (2 mm), and moderate traverse speed (200 mm/min). The SEM and optimal microscopy analysis confirmed that CNT reinforcement positively influenced fiber matrix interfacial integrity and reduced surface damage. Full article

Twinning-induced plasticity (TWIP) steels represent a significant development in automotive steel production, characterized by advanced strength and ductility properties. The present study empirically investigated the effects of process parameters on the cutting process and surface quality of TWIP980 steel sheet by abrasive water jet (AWJ) cutting. The cutting experiments were conducted on 1.4 mm thick sheet metal using four different traverse speeds (50, 100, 200, and 400 mm/min) and four different water jet pressures (1500, 2000, 2500, and 3000 bar). Two different abrasive flow rates (300 and 600 g/min) were also utilized. The cut surfaces were characterized in three dimensions with an optical profilometer. The parameters of surface roughness, kerf width, taper angle, and material removal rate (MRR) were determined. Furthermore, microhardness measurements were conducted on the cut surfaces. The optimal surface quality and geometrical accuracy were achieved by applying a combination of parameters, including 3000 bar of pressure, a traverse rate of 400 mm/min, and an abrasive flow rate of 600 g/min. Concurrently, an effective cutting performance with increased MRR and reduced taper angles was achieved under these conditions. The observed increase in microhardness with increasing pressure is attributable to a hardening effect resulting from local plastic deformation. Full article

Abrasive waterjet technology is a promising sustainable and green technology for cutting underground structures. Abrasive waterjet usage in demolition promotes sustainable and green construction practices by reduction of noise, dust, secondary waste, and disturbances to the surrounding infrastructure. In this study, a numerical framework based on a coupled Smoothed Particle Hydrodynamics (SPH)–Finite Element Method (FEM) algorithm incorporating the Riedel–Hiermaier–Thoma (RHT) constitutive model is proposed to investigate the damage mechanism of concrete subjected to abrasive waterjet. Numerical simulation results show a stratified damage observation in the concrete, consisting of a crushing zone (plastic damage), crack formation zone (plastic and brittle damage), and crack propagation zone (brittle damage). Furthermore, concrete undergoes plastic failure when the shear stress on an element exceeds 5 MPa. Brittle failure due to tensile stress occurs only when both the maximum principal stress (σ₁) and the minimum principal stress (σ₃) are greater than zero at the same time. The damage degree ($\chi$) of the concrete is observed to increase with jet diameter, concentration of abrasive particles, and velocity of jet. A series of orthogonal tests are performed to analyze the influence of velocity of jet, concentration of abrasive particles, and jet diameter on the damage degree and impact depth (h). The parametric numerical studies indicates that jet diameter has the most significant influence on damage degree, followed by abrasive concentration and jet velocity, respectively, whereas the primary determinant of impact depth is the abrasive concentration followed by jet velocity and jet diameter. Based on the parametric analysis, two optimized abrasive waterjet configurations are proposed: one tailored for rock fragmentation in tunnel boring machine (TBM) operations; and another for cutting reinforced concrete piles in shield tunneling applications. These configurations aim to enhance the efficiency and sustainability of excavation and tunneling processes through improved material removal performance and reduced mechanical wear. Full article

The use of UHP for food processing includes many applications such as cutting, peeling, pasteurization, and pumping through the orifice to affect food rheology. This paper focuses on food cutting applications using UHP waterjets. State-of-the-art food cutting systems are described including pumps, manipulators, sensors, cutting heads, and software. While UHP technology is commercially available at 621 MPa of pressure, most food cutting systems’ pressure is below 400 MPa. Highly focused waterjets are important for efficient slicing of food and thus diamond orifices with sharp entry edges are used in specially designed cutting using fast acting on/off valves. Automation is at an advanced level for fish, pin bone removal, poultry, meat, and vegetable processing systems where upstream sensor data are used with CNC controllers to determine the paths of the cutting jet(s) at relatively high production rates for portioning or trimming to tight specifications. Harvesting lettuce proved to be highly successful in improving the overall productivity and working environment ergonomics. An important advantage of the waterjet in increasing the shelf life of trimmed food is presented. For example, celery and lettuce shelf life increases by days over mechanical cutting. The use of salt as an abrasive material in abrasive waterjet cutting nozzles was found to be impractical for cutting meat with bone and more work is needed in this area. Bakery, cake, and sandwich cutting applications are utilized in actual plants in the USA and Europe. For example, small envelop cake cutting machines using relatively low-power jets are used for cutting cake into different shapes. Full article

The use of 3D roughness parameters is increasingly gaining ground in various areas of engineering, especially in academic research. In many cases, however, these studies primarily cover the illustration of the character of the surfaces, the interpretation of areal numerical roughness values is often disputed. The goal of this paper is to examine how the 2D and 3D roughness parameters change in the case of anisotropic surfaces, such as surfaces cut with an abrasive water jet. For this purpose, abrasive water jet cutting experiments were performed on AlMgSi0.5 aluminum alloy using different technological parameters. After the experiments, two amplitude-type 3D roughness parameters (S_a and S_z) of the cut surface and four profile parameters (R_a, R_z for roughness and P_a, P_z for raw profile) were measured at five different depths. Our conducted research indicates that the 3D parameters represent a kind of average value for certain roughness characteristics and a maximum value for others. The paper also reports on how these roughness characteristics change as a function of feed speed. Full article

To enhance the erosion efficiency in traditional abrasive water jet processing, an abrasive water jet processing method based on self-excited fluid oscillation is proposed. Traditional abrasive water jet methods suffer from reduced jet kinetic energy due to the presence of a stagnation layer, which hinders efficient material removal. By integrating a self-oscillation chamber into the conventional abrasive water jet nozzle, the continuous jet is transformed into a pulsed jet, thereby increasing the jet velocity and enhancing the kinetic energy of the process. This modification aims to improve material removal efficiency. Using Ansys Fluent, we simulated the material removal efficiency on workpiece surfaces with varying lengths of self-oscillation chambers. The simulation results reveal that the optimal length of the self-oscillation chamber for maximum erosion is 4 mm. SiC materials were used to evaluate the impact of self-oscillation chamber length (L), jet pressure (P), abrasive flow rate (M), and abrasive grain size (D) on erosion. Experimental results show that the self-oscillation chamber increases erosion depth by 33 μm. The maximum erosion depths recorded were 167 μm when L = 4 mm, 223 μm when P = 16 MPa, 193 μm when M = 80 g/min, and 268 μm when D = 2000 μm. Overall, the self-excited oscillation effect enhances the erosion efficiency of the waterjet by 14%. This study further elucidates the factors influencing erosion behaviors in oscillating abrasive water jet processing. Full article