Search Results (75)

Manganese-based oxides, particularly β-MnO₂, have emerged as promising cathode materials for aqueous zinc-ion batteries (ZIBs) due to their high theoretical capacity, low cost, and intrinsic safety. However, their sluggish reaction kinetics, limited active sites, and poor conductivity often lead to suboptimal electrochemical performance. To address these limitations, we propose a facile ethanol-mediated hydrothermal strategy to engineer rod-like β-MnO₂ nanostructures with tailored oxygen vacancies. By precisely adjusting ethanol addition (3–5 mL) during synthesis, oxygen vacancy concentrations were optimized to enhance electronic conductivity and active site exposure. The experimental results demonstrate that β-MnOx-2-5 synthesized with 5 mL of ethanol delivers an exceptional areal capacity of 4.87 mAh cm⁻² (348 mAh g⁻¹, 469.8 Wh kg⁻¹) at 200 mA cm⁻² under a high mass loading of 14 mg cm⁻². Further, a hybrid electrode combining oxygen-deficient β-MnO₂-x-3 (air-calcined) and structurally stable β-Mn₅O₈-y-3 (Ar-calcined) achieves a retained capacity of 3.9 mAh cm⁻² with stable cycling performance, achieving an optimal equilibrium between high capacity and long-term operational durability. Systematic characterizations (XPS, ESR, XANES, FT-EXAFS) confirm vacancy-induced electronic structure modulation, accelerating ion diffusion and redox kinetics. This scalable vacancy engineering approach, requiring only ethanol dosage control, presents a viable pathway toward industrial-scale ZIB applications. Full article

Unlike on Fe and Co catalysts, the CO conversion effect on Ru catalyst performance is little reported. This study is undertaken to explore the issue using a series of Ru/NaY catalysts under 200–230 °C, 2.0 MPa, H₂/CO = 2, and 10–60% CO conversion in a 1 L continuous stirred tank reactor (CSTR). The results are comparatively studied with those of Fe and Co catalysts reported previously. The NaY support and four 1.0%, 2.5%, 5.0%, and 7.5% Ru/NaY catalysts were characterized by BET, H₂ chemisorption, H₂O-TPD, XRD, HRTEM, and XANES/EXAFS techniques. The BET and XRD results suggest a high surface area (730 m²/g), high degree of crystallinity of the NaY support, and high dispersion of Ru, while an hcp Ru structure and well-reduced Ru were reflected in the HR-TEM FFT and XANES/EXAFS results. The reaction results indicate that the CO conversion effect on CH₄ and C₅₊ selectivities on the Ru is the same as that on the Fe and Co catalysts, with CH₄ selectivity decreasing and C₅₊ selectivity increasing with increasing CO conversion. However, the CO conversion effect on olefin formation for the Ru catalyst was found to be opposite to that of the Fe and Co; increasing CO conversion enhanced olefin formation but suppressed secondary reactions of 1-olefins. The H₂O cofeeding experiments showed that H₂O impacted olefin formation by suppressing hydrogen adsorption and hydrogenation. The H₂O-TPD experiment evidenced a much stronger H₂O adsorption capacity (6.8 mmol/g-cat) on Ru followed by Co (1 mmol/g-cat), and then Fe (0.2 mmol/g-cat)., which showed only a very low H₂O adsorption capacity.This finding may explain the opposite CO conversion effect on olefin formation observed on the Ru catalyst, and may also explain why low CH₄ selectivity (i.e., 3%) occurred on the Ru catalyst and high CH₄ selectivity (i.e., 6–8%) occurred on the Co catalyst, both of which possess low water gas shift (WGS) activity. Full article

Ce₂Pt₆Ga₁₅ is a heavy fermion compound near the quantum critical point (QCP). Its crystal structure may exhibit magnetic frustration due to a honeycomb arrangement; however, stacking faults in the crystal hinder structural analysis. As a local structure probe, extended X-ray absorption fine structure (EXAFS) is less sensitive to stacking faults and is a powerful tool for crystal structure determination. We synthesized single-crystal Ce₂Pt₆Ga₁₅, performed single-crystal and powder X-ray diffraction experiments, and conducted X-ray absorption spectroscopy (XAS) measurements. The composition of Ce₂Pt₆Ga₁₅ deviates from stoichiometry, suggesting Ce and Ga enrichment or Pt site deficiencies. A comparison of X-ray absorption near-edge structure (XANES) at the Ce L₃-edge with reference materials suggests that Ce valence is likely trivalent. To determine the exact structure, we simultaneously analyzed EXAFS spectra at the Ce L₃-, Pt L₃-, and Ga K-edges. The EXAFS spectra of Ce₂Pt₆Ga₁₅ are inconsistent with the hexagonal Sc_0.6Fe₂Si_4.9-type structure but are better explained by an orthorhombic structure with a honeycomb arrangement. Full article

Some of the largest Mexican uranium (U) deposits are located in Chihuahua. The most important is in Sierra Peña Blanca, northwest of the capital, which was explored and partially exploited in the 1980s. After the closure of activities, the mining projects were left exposed to weathering. To characterize the spread of U minerals towards the neighboring Laguna del Cuervo, sediment samples were collected in the main streams of the drainage pattern of the largest deposits. The U mineral fragments from the fine sand portion were extracted using fluorescence light at 365 nm. The morphology and elemental composition of these particles were analyzed by focused ion beam microscopy (FIB) and scanning transmission electron microscopy (STEM). The particle density in samples close to the U sources was quantified using gamma spectrometry. The highest density was 2500 part./g, and the lowest was 124 part./g. X-ray absorption spectroscopy (XAS) allowed us to establish via XANES the speciation of U in the U particles, confirming the U(VI) oxidation state, while the exploitation of the EXAFS spectrum put in evidence of the presence of uranophane. Finally, the Fe, Sr, and U distributions in the particle and its matrix were obtained via X-ray fluorescence microtomography (XRF-µCT). It was concluded that the particle is composed of uranophane, imbricated with quartz and other oxides. Full article

This study explores the phase composition, local atomic structure, and magnetic properties of biogenic nanomaterials synthesized through microbially mediated biomineralization by the sulfate-reducing bacterium Desulfovibrio species strain A2 (Cupidesulfovibrio). Using X-ray diffraction (XRD), transmission electron microscopy (TEM), Mössbauer spectroscopy, X-ray absorption near-edge structure (XANES) spectroscopy, extended X-ray absorption fine structure (EXAFS) spectroscopy, and magnetic measurements, we identified a mixture of vivianite (Fe₃(PO₄)₂·8H₂O) and sulfur-containing crystalline phases (α-sulfur). XRD analysis confirmed that the vivianite phase, with a monoclinic I2/m structure, constitutes 44% of the sample, while sulfur-containing phases (α-sulfur, Fddd) account for 56%, likely as a result of bacterial sulfate-reducing activity. X-ray absorption spectroscopy (XAS) and EXAFS revealed the presence of multiple sulfur oxidation states, including elemental sulfur and sulfate (S⁶⁺), underscoring the role of sulfur in the sample’s structure. Mössbauer spectroscopy identified the presence of ferrihydrite nanoparticles with a blocking temperature of approximately 45 K. Magnetic measurements revealed significant coercivity (~2 kOe) at 4.2 K, attributed to the blocked ferrihydrite nanoparticles. The results provide new insights into the structural and magnetic properties of these microbially mediated biogenic nanomaterials, highlighting their potential applications in magnetic-based technologies. Full article

This study conducted adsorption experiments using Europium (Eu(III)) on geological materials collected from Taiwan. Batch tests on argillite, basalt, granite, and biotite showed that argillite and basalt exhibited strong adsorption reactions with Eu. X-ray diffraction (XRD) analysis also clearly indicated differences before and after adsorption. By combining X-ray absorption near-edge structure (XANES), extended X-ray absorption fine structure (EXAFS), and wavelet transform (WT) analyses, we observed that the Fe₂O₃ content significantly affects the Eu-Fe distance in the inner-sphere layer during the Eu adsorption process. The wavelet transform analysis for two-dimensional information helps differentiate two distances of Eu-O, which are difficult to analyze, with hydrated outer-sphere Eu-O distances ranging from 2.42 to 2.52 Å and inner-sphere Eu-O distances from 2.27 to 2.32 Å. The EXAFS results for Fe₂O₃ and SiO₂ in argillite and basalt reveal different adsorption mechanisms. Fe₂O₃ exhibits inner-sphere surface complexation in the order of basalt, argillite, and granite, while SiO₂ forms outer-sphere ion exchange with basalt and argillite. Wavelet transform analysis also highlights the differences among these materials. Full article

X-ray absorption fine structure (XAFS) spectroscopy, temperature-programmed reduction (TPR), and temperature-programmed hydride decomposition (TPHD) were employed to elucidate the structures of a series of PdRe/Al₂O₃ bimetallic catalysts for the selective hydrogenation of furfural. TPR evidenced low-temperature Re reduction in the bimetallic catalysts consistent of the migration of [ReO₄]⁻ (perrhenate) species to hydrogen-covered Pd nanoparticles on highly hydroxylated γ-Al₂O₃. TPHD revealed a strong suppression of β-PdH_x formation in the reduced catalysts prepared by (i) co-impregnation and (ii) [HReO₄] impregnation of the reduced Pd/Al₂O₃, indicating the formation of Pd-rich alloy nanoparticles; however, reduced catalysts prepared by (iii) [Pd(NH₃)₄]²⁺ impregnation of calcined Re/Al₂O₃ and subsequent re-calcination did not. Re L_III X-ray absorption edge shifts were used to determine the average Re oxidation states after reduction at 400 °C. XAFS spectroscopy and high-angle annular dark field (HAADF)-scanning transmission electron microscopy (STEM) revealed that a reduced 5 wt.% Re/Al₂O₃ catalyst contained small Re clusters and nanoparticles comprising Re atoms in low positive oxidation states (~1.5+) and incompletely reduced Re species (primarily Re⁴⁺). XAFS spectroscopy of the bimetallic catalysts evidenced Pd-Re bonding consistent with Pd-rich alloy formation. The Pd and Re total first-shell coordination numbers suggest that either Re is segregated to the surface (and Pd to the core) of alloy nanoparticles and/or segregated Pd nanoparticles are larger than Re nanoparticles (or clusters). The Cowley short-range order parameters are strongly positive indicating a high degree of heterogeneity (clustering or segregation of metal atoms) in these bimetallic catalysts. Catalysts prepared using the Pd(NH₃)₄[ReO₄]₂ double complex salt (DCS) exhibit greater Pd-Re intermixing but remain heterogeneous on the atomic scale. Full article

This work presents the results of studying dilute aqueous solutions of commercial Ln(NO₃)₃ · xH₂O salts with Ln = Ce-Lu using X-ray diffraction (XRD), IR spectroscopy, X-ray absorption spectroscopy (XAS: EXAFS/XANES), and pH measurements. As a reference point, XRD and XAS measurements for characterized Ln(NO₃)₃ · xH₂O microcrystalline powder samples were performed. The local structure of Ln-nitrate complexes in 20 mM Ln(NO₃)₃ · xH₂O aqueous solution was studied under total external reflection conditions and EXAFS geometry was applied to obtain high-quality EXAFS data for solutions with low concentrations of Ln³⁺ ions. Results obtained by EXAFS spectroscopy showed significant contraction of the first coordination sphere during the dissolution process for metal ions located in the middle of the lanthanide series. It was established that in Ln(NO₃)₃ · xH₂O solutions with Ln = Ce, Sm, Gd, Yb (c = 134, 100, 50 and 20 mM) there are coordinated and, to a greater extent, non-coordinated nitrate groups with bidentate and predominantly monodentate bonds with Ln ions, the number of which increases upon transition from cerium to ytterbium. For the first time, the antibacterial and antifungal activity of Ln(NO₃)₃ · xH₂O Ln = Ce, Sm, Gd, Tb, Yb solutions with different concentrations and pH was presented. Cross-relationships between the concentration of solutions and antimicrobial activity with the type of Ln = Ce, Sm, Gd, Tb, Yb were established, as well as the absence of biocidal properties of solutions with a concentration of 20 mM, except for Ln = Yb. The important role of experimental conditions in obtaining and interpreting the results was noted. Full article

The ability to study chemical dynamics on ultrafast timescales has greatly advanced with the introduction of X-ray free electron lasers (XFELs) providing short pulses of intense X-rays tailored to probe atomic structure and electronic configuration. Fully exploiting the full potential of XFELs requires specialized experimental endstations along with the development of techniques and methods to successfully carry out experiments. The liquid jet endstation (LJE) at the Linac Coherent Light Source (LCLS) has been developed to study photochemistry and biochemistry in solution systems using a combination of X-ray solution scattering (XSS), X-ray absorption spectroscopy (XAS), and X-ray emission spectroscopy (XES). The pump–probe setup utilizes an optical laser to excite the sample, which is subsequently probed by a hard X-ray pulse to resolve structural and electronic dynamics at their intrinsic femtosecond timescales. The LJE ensures reliable sample delivery to the X-ray interaction point via various liquid jets, enabling rapid replenishment of thin samples with millimolar concentrations and low sample volumes at the 120 Hz repetition rate of the LCLS beam. This paper provides a detailed description of the LJE design and of the techniques it enables, with an emphasis on the diagnostics required for real-time monitoring of the liquid jet and on the spatiotemporal overlap methods used to optimize the signal. Additionally, various scientific examples are discussed, highlighting the versatility of the LJE. Full article

The Hayabusa2 space mission recently retrieved 5.4 g of material from asteroid Ryugu, providing the first direct access to pristine material from a carbonaceous asteroid. This study employs a novel combination of non-invasive synchrotron X-ray techniques to examine microscale chemistry (elemental distributions and element-specific chemical speciation and local structure) inside Ryugu grains without physically cutting the samples. Manganese primarily occurs in carbonate: Mn-bearing dolomite with minor earlier ankerite. Iron sulfides present as large single grains and as smaller particles in the finer-grained matrix are both predominantly pyrrhotite. At the 5 μm scale, Fe sulfides do not show the mineralogical heterogeneity seen in many carbonaceous meteorites but exhibit some heterogeneous localized oxidation. Iron is present often as intergrowths of oxide and sulfide, indicating incomplete replacement. Trace selenium substitutes for S in pyrrhotite. Copper is present as Fe-poor Cu sulfide. These results demonstrate multiple episodes of fluid alteration on the parent body, including partial oxidation, and help constrain the sequence or evolution of fluids and processes that resulted in the current grain-scale mineralogical composition of Ryugu materials. Full article

Margaritasite is a mineral compound discovered in the early 1980s in Chihuahua, Mexico. It is a natural cesium uranyl vanadate found only, so far, in the Margaritas mine of the Peña Blanca highlands. In this work, a thorough characterization of the aforementioned mineral is presented. The portfolio of the techniques employed includes high-resolution X-ray diffraction, scanning electron microscopy with energy dispersive X-ray spectroscopy, transmission electron microscopy in selected area electron diffraction (SAED) mode, and X-ray absorption spectroscopy (XAS). After extensive data analysis and modeling, new information on the mineral has been retrieved. Its phase composition is margaritasite–carnotite: a solid solution of cesium and potassium uranyl vanadate [(Cs,K)₂(UO₂)₂(VO₄)₂·nH₂O], and margaritasite, which is practically pure cesium uranyl vanadate [Cs₂(UO₂)₂(VO₄)₂·nH₂O]. The crystal structure of both components presents the space group P 1 2₁/c 1. Yet, each phase has similar, but appreciably different, lattice parameters. The mineral has a lamellar tabular and prismatic morphology. SAED patterns confirm the crystal structure of margaritasite. XAS spectra of Cs, V, and U confirm the elemental composition, oxidation states, and interatomic distances of this structure. These findings are consistent with the presence of cesium in this unique mineral from the paragenesis point of view. Full article

Hydrodechlorination reaction of 3-(benzo-1,3-dioxol-5-yl)-3-chloro-2-methylacrylaldehyde in the presence of different low metal content heterogeneous mono- or bimetallic catalysts was tested for the synthesis of the fragrance Helional^® (3-[3,4-methylendioxyphenyl]-2-methyl-propionaldehyde). In particular, mono Pd/Al₂O₃, Rh/Al₂O₃ or bimetallic Pd-Cu/Al₂O₃, Rh-Cu/Al₂O₃ catalysts were tested in different reaction conditions from which it emerged that mono-Rh/Al₂O₃ was the best performing catalyst, allowing achievement of 100% substrate conversion and 99% selectivity towards Helional^® in 24 h at 80 °C, p(H₂) 1.0 MPa in the presence of a base. To establish correlations between atomic structure and catalytic activity, catalysts were characterized by Cu, Rh and Pd K-edge XANES, EXAFS analysis. These characterizations allowed verification that the formation of Pd-Cu alloys and the presence of Cu oxide/hydroxide species on the surface of the Al₂O₃ support are responsible for the very low catalytic efficiency of bimetallic species tested. Full article

Uranium (U) and nickel (Ni) released 50 years ago have been immobilized in the Tims Branch wetlands located on the Savannah River Site in the United States. Sediments were collected from seven locations to identify the factors responsible for this attenuation. Ni and U contents in the solids were significantly correlated, suggesting that depositional as opposed to chemical processes contributed to their spatial distribution. Based on sequential extractions, 63 ± 16% of the U was partitioned into the organic fraction, whereas Ni was distributed between several sediment fractions. An inverse pH-organic matter (OM) correlation and positive correlations of OM with total U and organic-bound U/Ni suggest that increased OM preservation and binding to the mineral surfaces were likely responsible for Ni- and especially U-sediment retention (Tims Branch pH = 4.84 ± 0.68). EXAFS analysis indicated the predominance of U(VI) coordinated with clay minerals (~65%), together with ~35% coordinated to either OM (in areas with elevated OM levels) or iron oxides. The desorption-K_d coefficients of U (3972 ± 1370 L/kg) and Ni (30 ± 8 L/kg) indicate that dissolved Ni poses a greater long-term risk than dissolved U for migrating downstream. This study suggests that a delicate balance of geochemical properties controls whether wetlands behave as sinks or sources of contaminants. Full article

We have investigated the effect of the Ni substitution on the local structure and the valence electronic states of the ${\mathrm{SrFe}}_{2-x}$${\mathrm{Ni}}_x$${\mathrm{As}}_2$ (x = 0.00, 0.16, and 0.23) superconductor with a multi-edge extended X-ray absorption fine structure (EXAFS) and X-ray absorption near edge structure (XANES) spectroscopy. The As K-edge and Fe K-edge EXAFS measurements in the two polarizations (E‖ab and E‖c) show a clear change in the local structure with Ni concentration. The near-neighbor bondlengths and the related mean-square relative displacements (MSRDs) decrease as the Ni content increases. The polarized XANES spectra at the As, Fe and Ni K edges reveal a systematic change in the anisotropy of the valence electronic structure. The results suggest that the quasi 2D electronic structure of this system tends to become more isotropic as the Ni content increases. The local structure and the valence electronic states are discussed in the frame of the evolving electronic transport of the ${\mathrm{SrFe}}_{2-x}$${\mathrm{Ni}}_x$${\mathrm{As}}_2$ system. Full article

Silica-supported chromium oxide catalysts, also named Phillips chromium catalysts (PCCs), provide more than half of the world’s production of high- and medium-density polyethylenes. PCCs are usually prepared in the Cr(VI)/SiO₂ form, which is subjected to reductive activation. It has been explicitly proven that CO reduces Cr(VI) to Cr(II) species that initiate ethylene polymerization; ethylene activates Cr(VI) sites as well, but the nature of the catalytic species is complicated by the presence of the ethylene oxidation products. It is widely accepted that the catalytic species are of a Cr(III)–alkyl nature, but this common assumption faces the challenge of “extra” hydrogen: the formation of similar species under the action of even-electron reducing agents requires an additional H atom. Relatively recently, it was found that saturated hydrocarbons can also activate CrO_x/SiO₂, and alkyl fragments turn out to be bonded with a polyethylene chain. In recent years, there have been numerous experimental and theoretical studies of the structure and chemistry of PCCs at the different stages of preparation and activation. The use of modern spectral methods (such as extended X-ray absorption fine structure (EXAFS), X-ray absorption near-edge structure (XANES), and others); operando IR, UV–vis, EPR, and XAS spectroscopies; and theoretical approaches (DFT modeling, machine learning) clarified many essential aspects of the mechanisms of CrO_x/SiO₂ activation and catalytic behavior. Overall, the Cosse–Arlman mechanism of polymerization on Cr(III)–alkyl centers is confirmed in many works, but its theoretical support required the development of nontrivial and contentious mechanistic concepts of Cr(VI)/SiO₂ or Cr(II)/SiO₂ activation. On the other hand, conflicting experimental data continue to be obtained, and certain mechanistic concepts are being developed with the use of outdated models. Strictly speaking, the main question of what type of catalytic species, Cr(II), Cr(III), or Cr(IV), comes into polymerization still has not received an unambiguous answer. The role of the chemical nature of the support—through the prism of the nature, geometry, and distribution of the active sites—is also not clear in depth. In the present review, we endeavored to summarize and discuss the recent studies in the field of the preparation, activation, and action of PCCs, with a focus on existing contradictions in the interpretation of the experimental and theoretical results. Full article