Search Results (548)

Hydrolysis of cellulose to produce ethanol has become an effective way to utilize biological resources, but its large-scale industrial application has been limited. In this study, a one-pot catalytic conversion process for transforming cellulose into ethanol was developed. Meanwhile, multifunctional Mo/Pt/WO_x/Al₂O₃ catalysts were prepared by loading nano-alumina (Nano-Al₂O₃) via a stepwise impregnation method. The influence of catalysts with varying metal ratios on the types of products generated during the cellulose hydrolysis process to ethanol was examined. The catalyst with 0.1% Mo, 2% Pt, and 7.5% W loadings showed the best selectivity. With an ethanol yield of 45.3% after heating at 5 MPa H₂ and 518 K for 2 h. Nano-Al₂O₃ can provide suitable active sites. The addition of W⁵⁺ and Mo⁰ increased the surface oxygen vacancy density and enhanced the hydrodeoxidation and metal anchoring capacity of the catalyst. The solid solution structure facilitates electron transfer from W and Mo atoms to Pt atoms, forming electron-rich Pt^δ- species, promoting the hydrolysis of cellulose and the formation of ethanol. Full article

This review analyzes electrochemically deposited polyaniline (PANI) nanocomposite thin films containing metallic, semiconducting, and dielectric fillers, including Ag/PANI, Mo/MoO_x/PANI, CeO₂/PANI, Fe₂O₃/PANI, Al₂O₃/PANI, CuO/PANI, Co₃O₄/PANI, and CoFe₂O₄/PANI. The work examines how filler chemistry and loading influence optical-gap evolution, Urbach disorder, dielectric dispersion, nonlinear optical response, structural coherence, and dc conductivity under comparable electrochemical growth conditions. The comparative analysis shows that optical-gap narrowing and conductivity enhancement are not necessarily coupled. Ag/PANI exhibits simultaneous optical softening and improved conductivity, consistent with metallic bridging, dielectric screening, and enhanced charge connectivity. In contrast, Mo/MoO_x/PANI shows strong optical-gap reduction but reduced conductivity, indicating that optically active interfacial states may remain localized or mobility-limiting. Oxide fillers produce additional regimes: CeO₂/PANI can suppress Urbach disorder and microstrain through order stabilization, whereas Al₂O₃/PANI may widen higher-energy transitions and reduce transport through wide-gap barrier effects. Based on these contrasts, a unified framework is proposed that separates the interfacial electronic function from the transport-connectivity function. This approach classifies PANI nanocomposites into transport-assisted metallic, mobility-limiting interfacial, order-stabilized oxide, and barrier-dominated dielectric regimes, providing practical criteria for selecting filler type and loading windows in optoelectronic, sensing, and photonic applications. Full article

New lacunary Keggin-type polyoxometalate salts with the formula Cs₅PMMo₁₁(H₂O)O₃₉ (M = Cu, Zn) were synthesized via the inorganic solution condensation method. X-ray diffraction and FT-IR spectroscopy confirmed the preservation of the Keggin structure. The surface morphology and elemental composition were characterized using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. Thermal analysis, performed by differential scanning calorimetry coupled with thermogravimetry, demonstrated a significant enhancement in thermal stability upon the incorporation of the transition metals into the heteropolyacid framework. Specifically, the substitution of protons by cesium and of molybdenum by copper or zinc positively influenced the crystallographic configuration of the salts, raising their thermal resistance (up to 526 °C). Furthermore, optical and dielectric measurements revealed promising electronic properties in the synthesized lacunary salts. Notably, the compound Cs₅PZnMo₁₁(H₂O)O₃₉ exhibited a substantially increased dielectric constant at low frequency, underscoring the synergistic effect of zinc addition on its dielectric performance. Full article

A numerical investigation of forced convection heat transfer in a three-dimensional T-shaped bifurcating channel with an upstream rotating cylinder and a downstream vibrating wavy wall is presented. The working fluid is a ternary hybrid nanofluid (Fe₂O₃, CuO, MoS₂ in water) exhibiting Casson rheology under an inclined magnetic field. The novelty of this work lies in the first integrated configuration combining these simultaneous mechanical, magnetic, and non-Newtonian effects. Using COMSOL Multiphysics, 413 parametric combinations of Reynolds number, Hartmann number, Casson parameter, nanoparticle shape and volume fraction, magnetic field angle, cylinder rotation speed, wall amplitude (Am), and period were solved. Average Nusselt and Bejan numbers quantified heat transfer enhancement and thermodynamic irreversibility. To interpret the high-dimensional parameter space and to circumvent the prohibitive computational cost of additional 3D magnetohydrodynamics simulations, machine learning (XGBoost) models were developed to rank feature importance and provide fast, accurate surrogate predictions (R² > 0.99). Cylinder rotation dominates heat transfer, increasing the Nusselt number by over 980% (feature importance 0.42) with a modest entropy penalty. Nanoparticle volume fraction reduces the Nusselt number via viscous damping. Magnetic field parameters negligibly affect heat transfer but strongly influence entropy generation; a perpendicular field recovers up to 97% thermal efficiency at high Hartmann numbers. Full article

This study investigates the mechanochemical synthesis of silver molybdate (Ag₂MoO₄). Three silver precursors (AgCl, AgNO₃, Ag₂SO₄) in combination with sodium molybdate dihydrate as the molybdenum precursor were used. Three corresponding sodium salts, which are also formed as byproducts, were employed as process control agents (PCAs) to investigate the possibility of obtaining fine-grained silver molybdate. Milling was performed in a planetary mill at 600 and 100 rpm, and for 2 h, 15 min, and 5 min. X-ray diffraction analysis (XRD) revealed that AgCl is completely unreactive in this type of reaction, whereas AgNO₃ and Ag₂SO₄ form crystalline Ag₂MoO₄. Additional sample characterization included Fourier transform infrared spectroscopy (FTIR), UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and simultaneous differential thermal and thermogravimetric analysis (DTA-TGA). The results indicate that the silver molybdate formation reaction is favorable and rapid. Even under the mildest conditions, including the presence of PCA, micron-sized silver molybdate particles were obtained. A greater rotation rate and longer milling time resulted in a decrease in particle size, but also an increase in sodium content. However, unlike the few existing reports on the mechanochemical synthesis of Ag₂MoO₄, which, despite harsh milling conditions, did not yield a phase-pure product, our approach produced well-crystallized and pure silver molybdate even under the mildest synthesis conditions. Full article

This study investigates the possibility of producing a complex W–Mo–Cr-containing alloy via metallothermic reduction of oxide concentrates in the presence of direct reduced iron (DRI) in an induction furnace under atmospheric conditions. A complex FeAlSiCa alloy was used as a reductant due to its high exothermicity and combined reducing potential. Thermodynamic analysis showed that the reduction of WO₃ and MoO₃ is more favorable compared to Cr₂O₃, which is reflected in the temperature profiles of the process. Experimental results confirmed that the addition of FeAlSiCa leads to intensive exothermic reactions and promotes melt formation. The estimated apparent recovery of W and Mo reached up to ~99%, while Cr estimated apparent recovery remained lower (up to ~70%) due to its higher thermodynamic stability and kinetic limitations. Microstructural analysis revealed a heterogeneous structure consisting of an Fe-based matrix and W–Mo-rich phases, including characteristic “fishbone” morphologies. An increase in reductant amount led to higher Si content in the alloy, indicating the need for composition optimization. The results demonstrate the feasibility of direct complex alloying as an alternative to conventional ferroalloy-based methods and highlight the potential for developing resource-efficient and low-carbon metallurgical technologies. Full article

Molybdenum (Mo) is a strategic raw material for high-end equipment manufacturing, aerospace technologies, and advanced alloys, and approximately 50% of global molybdenum resources are hosted in porphyry Cu–Mo deposits. To address the long-standing challenge of selectively separating chalcopyrite and molybdenite by flotation, this study screened five sulfur-containing organic depressants and investigated their effects on the flotation responses of the two minerals, motivated by the strong affinity of sulfur donor atoms for surface Cu sites on chalcopyrite. The results indicate that thiomalic acid, 4-hydroxythiobenzamide, and 6-methyl-2-thiouracil markedly depress chalcopyrite flotation, whereas 2-(methylthio)acetic acid and N-phenylthiourea exert only minor effects. In contrast, none of the five reagents significantly affects the floatability of molybdenite. Among these depressants, thiomalic acid exhibited the best selectivity. In practical Cu–Mo bulk concentrate flotation, it showed a clear dosage advantage at low addition levels and improved Cu–Mo separation performance; at a Mo recovery of 76.09% and a Mo grade of 5.45%, Cu recovery was reduced to 9.54%. The adsorption mechanism of thiomalic acid on chalcopyrite was further investigated using FT-IR spectroscopy, X-ray photoelectron spectroscopy, and self-consistent charge density-functional tight-binding (SCC-DFTB) calculations. The results suggest that thiomalic acid interacts strongly with surface Cu sites on chalcopyrite via its S- and O-containing functional groups, likely increasing surface hydrophilicity and inhibiting collector adsorption (and subsequent bubble attachment), thereby contributing to selective chalcopyrite depression. Full article

Over the next decade, advanced lithium-based secondary batteries will require high-performance anodes to achieve superior energy density and cycling stability. In this work, anatase titanium dioxide nanotube arrays (TiO₂ NTs) are fabricated on ultrathin Ti paper through anodization and subsequently thermal annealing. An urchin-like 2H-MoS₂ coating is subsequently deposited onto the TiO₂ NTs substrate through magnetic sputtering, constructing a self-supported hierarchical architecture without any additives. Electrochemical characterizations demonstrate that the MoS₂/TiO₂ NTs/Ti composite exhibits lower charge transfer resistance, enhanced rate capability, and improved cycling stability compared with bare TiO₂ NTs/Ti and worm-like MoS₂/Ti control groups. Structural analysis and density functional theory calculations further confirm that the strong interfacial interaction between MoS₂ and TiO₂ effectively stabilizes interfacial integrity during repeated cycling. Upon leveraging tunable geometric structure and mass loadings, this study offers a facile route for developing various types of advanced lithium-based secondary batteries. Full article

To elucidate the role of environmentally friendly oxide additives in a molybdenum disulfide (MoS₂)-based solid lubricant, this study investigates the tribological behavior of a MoS₂–TiO₂ coating deposited via a spray-bonding process and compares it with a commercial Sb₂O₃-containing formulation (Everlube 620C). Interfacial characteristics and wear-related mechanisms were systematically analyzed using scanning electron microscopy (SEM), focused ion beam (FIB), Raman spectroscopy, and X-ray diffraction (XRD). The MoS₂–TiO₂ coating exhibited a higher steady-state coefficient of friction (0.35–0.45) and wear compared to the baseline. Its wear behavior was governed by fracture-induced three-body abrasion, driven by the hard and brittle nature of TiO₂, which promotes stress concentration at particle–matrix interfaces, crack initiation, particle pull-out, and debris generation. These processes suppress the formation of a desirable MoS₂-rich tribo/transfer film, leading to deformation-dominated friction. Overall, the findings indicate that the intrinsic mechanical properties and interfacial behavior of TiO₂ limit its effectiveness as an additive in MoS₂-based coatings, highlighting the importance of additive selection and compatibility in achieving optimal tribological performance. Notably, this study was performed at an additive volume fraction equivalent to that of Sb₂O₃ in Everlube 620C, serving as a foundation and indicating that further optimization of TiO₂ particle size and concentration is required to achieve comparable performance. Full article

Zinc oxide (ZnO) nanomaterials have attracted widespread attention from researchers due to their morphology-dependent properties, eco-friendly characteristics, and potential as a sustainable photocatalyst with a broad range of applications. Therefore, in this study, three different ZnO nanostructures—nanosheets (NSs), nanoflowers (NFs), and nanorods (NBs)—were synthesized via a controlled precipitation method. Among these, NFs exhibited the highest photocatalytic efficiency. The obtained samples exhibited broad optical absorption edges extending into the visible region (corresponding to apparent energies of 1.81–2.09 eV), which is attributed to the sub-bandgap states induced by oxygen vacancies rather than intrinsic bandgap narrowing—far lower than the bandgap of bulk ZnO (3.37 eV). Their photocatalytic performance was evaluated by the degradation of Methyl Blue (MB), Methyl Orange (MO), and Rhodamine B (RhB) under UV or sunlight. Notably, the NFs achieved rapid degradation of MB and RhB within 90 min under UV irradiation without the addition of any H₂O₂, demonstrating their effectiveness and cost-effectiveness for practical applications. Although H₂O₂ inhibited the degradation of MB and RhB, it promoted the decomposition of MO. Furthermore, the ZnO NFs exhibited excellent recyclability in five consecutive degradation cycles. The self-synthesized ZnO nanomaterials in this study, with their broad-spectrum absorption, high stability, and eco-friendly properties, demonstrate their potential as an efficient and low-cost photocatalyst for large-scale wastewater treatment. Full article

The traditional solid-state method was employed in this study to prepare Mn-Zn ferrite. By adjusting the sintering temperature and the MoO₃ doping ratio, the evolution of its structural and magnetic properties was systematically investigated. Fe₂O₃, MnO, and ZnO were used as the main raw materials, with MoO₃ serving as an additive. MoO₃ was doped at molar ratios ranging from 0 to 1000 ppm under experimental conditions involving a sintering temperature between 1125 °C and 1165 °C and an oxygen concentration of 1.5%. The addition of an appropriate amount of MoO₃ led to an increase in the Q value, which consequently resulted in a reduction in the loss. The formation of a single-phase spinel structure was confirmed by X-ray diffraction analysis. Observations of the surface morphology revealed that the grain size also increased with the increase in MoO₃ content, a trend consistent with the enhanced grain growth kinetics at higher MoO₃ levels. In this study, a Mn-Zn ferrite material with excellent comprehensive performance was successfully prepared under the optimal conditions of a sintering temperature of 1150 °C and a MoO₃ doping concentration of 500 ppm. A Q value of 22.3 was obtained for this material at 25 °C, while a Q value of 15.7 was obtained at 100 °C. At room temperature, a Q value of 192.4 was measured at a test frequency of 500 kHz, and a Q value of 137.2 was measured at 1 MHz. At a frequency of 500 kHz, a loss of 27.1 kW/m³ was observed at 25 °C, and a loss of 53.6 kW/m³ was observed at 100 °C. At a frequency of 1 MHz, a loss of 88.2 kW/m³ was recorded at 25 °C, while a loss of 183.7 kW/m³ was recorded at 100 °C. Additionally, the lattice constant was stabilized in the range of 8.52–8.53 Å, indicating favorable structural stability. Full article

The influence of zirconia incorporation and template type on the physicochemical properties of NiMo/Al₂O₃-ZrO₂ catalysts was investigated for the hydrodesulfurization (HDS) of 4,6-dimethyldibenzothiophene (4,6-DMDBT) and the hydrogenation (HYD) of naphthalene (N). Catalysts were prepared by co-impregnation on supports synthesized via a sol-gel method using starch (A) and activated carbon (C) as structure-directing templates, followed by zirconium incorporation through a grafting procedure. The resulting materials were characterized by SEM–EDX, N₂ physisorption, H₂-TPR, XPS, HRTEM, and pyridine-FTIR. SEM-EDX confirmed homogeneous metal distributions and compositions close to nominal values (Mo = 20 wt%, Ni = 5 wt%, Zr = 11 wt%) with Ni/(Ni + Mo) = 0.30. N₂ adsorption–desorption isotherms correspond to type IV(a) with H3-H4 hysteresis loops, characteristic of mesoporous structures. After metal incorporation, surface areas decreased to 96 m² g⁻¹ for NiMo/Al₂O₃ and 81 m² g⁻¹ for Zr-modified catalysts, while the activated carbon-templated sample preserved a larger mesoporous volume (0.335 cm³ g⁻¹) and higher macroporosity (72%). H₂-TPR profiles indicated improved reducibility for Zr-containing catalysts. XPS revealed an increase of MoS₂ species from 45% in NiMo/Al₂O₃ to 75% in NiMo/Al₂O₃-ZrO₂(C), accompanied by a higher degree of sulfidation index (DSI) from 47.1% to 73.9%. HRTEM analysis of Zr-modified catalysts revealed longer MoS₂ slabs (11.8–12.1 nm) and higher edge-to-corner ratios (17–17.4) compared with NiMo/Al₂O₃ (6.2 nm; fe/fc = 8.2). Pyridine-FTIR showed a substantial increase in total acidity from 91 to 421 μmol g⁻¹ upon Zr addition. Catalytically, NiMo/Al₂O₃-ZrO₂(C) exhibited the highest HDS conversion (40%), reaction rate (10.5 × 10⁻⁹ mol s⁻¹ g⁻¹), and TOF (4.69 × 10⁻⁵ s⁻¹), whereas NiMo/Al₂O₃-ZrO₂(A) reached the highest naphthalene conversion (97.18%), with a reaction rate of 27.4 × 10⁻⁷ mol s⁻¹ g⁻¹ and TOF of 12.9 × 10⁻³ s⁻¹. These results demonstrate that Zr incorporation and the activated carbon template favored hydrodesulfurization, whereas the starch template promoted hydrogenation performance. Full article

Humic substances (HS), derived from the degradation of organic matter in terrestrial and aquatic systems, play critical roles in nutrient cycling, metal complexation, and soil fertility. This study investigates whether HS derived from Greek peaty lignite (leonardite) can bind Mo(VI), an essential micronutrient for nitrogen fixation and assimilation processes. Titration experiments showed that the addition of Mo(VI) to HS solutions decreased pH, indicating Mo(VI)–HS complexation via proton-release reactions. UV-Vis spectra revealed charge-transfer interactions without evidence of Mo reduction, while FTIR analysis confirmed that carboxylic, phenolic, and alcoholic groups participate in Mo(VI)–HS association as indicated by shifts in COO–, C=O, and O–H vibrations. The results demonstrate that HS can effectively complex Mo(VI), increasing its solubility and potentially enhancing its bioavailability in soils. These findings highlight the value of humic-rich materials such as leonardite in sustainable crop nutrition. Full article

Emission control of diesel particulate matter (soot) combustion is important for environmental reasons. Catalysts are indispensable for optimizing these processes, as they significantly reduce the combustion temperature. In this work, mixed oxides (cerium–copper, cerium–manganese, and cerium–molybdenum) were prepared by co-precipitation under reasonably similar synthesis conditions, and the effects of their chemical composition on diesel soot combustion were evaluated using the Printex U model particulate. Thermogravimetric analysis (TG/DTG) and temperature-programmed oxidation coupled with mass spectrometry (TPO/MS) were employed for activity characterization. Structural analyses revealed the presence of nanocrystalline phases containing CeO₂ (fluorite), CuO (monoclinic), Mn₂O₃ (cubic), and MoO₃ (orthorhombic), depending on the catalyst composition. The most effective catalysts exhibited an equimolar oxide composition (CeO₂–MO_x). Tests performed at optimized calcination temperatures and with the addition of promoters led to the identification of optimal combustion conditions. The highest activity, corresponding to the lowest combustion temperature, was observed in the following order: CeO₂–Mn₂O₃ > CeO₂–CuO > CeO₂–MoO₃, with values of 382, 409, and 425 °C, respectively, under tight-contact conditions at a Printex U:catalyst ratio of 1:20. With the addition of a 10% Ag₂O promoter, the CeO₂–Mn₂O₃ catalyst further reduced the oxidation temperature to 376 °C. Reusability tests generally indicated a 10–20% decrease in catalytic activity by the third reaction cycle. Full article

The present study demonstrates that the corrosion behavior of dental cobalt–chromium (Co–Cr) alloys is strongly influenced by the interaction between microstructure, manufacturing technique, and oral chemical environment. A comparative investigation was conducted on Co–Cr specimens fabricated using four technological routes: conventional casting, CAD/CAM machining, Selective Laser Melting (SLM), and Direct Metal Laser Sintering (DMLS). The study included microstructural characterization, evaluation of generalized corrosion behavior using the rotating electrode technique, assessment of localized crevice corrosion, and quantitative analysis of the release of twenty metallic cations. Extraction tests were performed for 168 h in two media simulating aggressive oral environments: 0.07 N HCl (acidic medium) and a fluoride-containing electrolyte (0.1% NaF + 0.1% KF). Electrochemical measurements were recorded in the current density range of 10⁻¹⁰ to 10⁻⁷ A/cm², while released cation concentrations were quantified at the µg/L level. All alloys exhibited very low corrosion current densities (icorr in the 10⁻⁸ to 10⁻⁹ A·cm⁻² range), confirming overall good corrosion resistance. Among all manufacturing routes, CAD/CAM specimens demonstrated the highest electrochemical performance, with a wide passivity domain extending up to approximately 740 mV/SCE. A statistical interaction analysis between extraction media and manufacturing techniques was performed using the non-parametric Mann–Whitney (MW) U test. Among the analyzed elements, only chromium showed a statistically significant difference between media (p < 0.05), with an approximately 25-fold-higher release in acidic conditions compared with the fluoride medium, confirming the predominant role of proton-induced destabilization of the protective Cr₂O₃ passive film. In contrast, fluoride-containing media induced selective release of elements such as Cu (3× higher), W (2.5× higher), and Mo (1.4× higher), associated with complexation phenomena. The manufacturing route significantly influences corrosion behavior. Although additive manufacturing technologies (SLM/DMLS) enable highly accurate and customized prosthetic designs, rapid solidification and microstructural heterogeneities may increase susceptibility to localized corrosion compared with more homogeneous CAD/CAM materials. Clinically, these findings suggest that future restorative strategies should incorporate corrosion-aware material selection within digital workflows. As digital dentistry evolves, predictive models integrating patient-specific oral conditions may assist clinicians in selecting the most appropriate material system for long-term performance. In conclusion, the long-term success of dental Co–Cr prosthetic devices depends not only on mechanical strength and precision of fit, but also on sustained electrochemical stability in the complex oral environment. Full article