ijms-logo

Journal Browser

Journal Browser

Synthesis of Advanced Polymer Materials

A special issue of International Journal of Molecular Sciences (ISSN 1422-0067). This special issue belongs to the section "Macromolecules".

Deadline for manuscript submissions: closed (15 December 2022) | Viewed by 21409

Special Issue Editor


E-Mail Website
Guest Editor
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
Interests: polymer chemistry; polymer synthesis; catalytic olefin polymerization; organometallic catalysts; metal-catalyzed polymerization; polyolefins
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

Polymer materials are found in almost every material used in daily life, and their importance has been highlighted because of their wide applications. With the rapid development of modern society, developing new and/or advanced polymer materials is constantly required. Therefore, the synthesis of advanced polymers has attracted considerable attention. This Special Issue of the International Journal of Molecular Sciences will focus on a collection of excellent research articles and review papers related to the synthesis of advanced polymer materials involving polymer synthesis, polymer chemistry, and polymer functionalization and modification. Every paper submitted for consideration is welcomed to report novel synthesis techniques, new synthesis methods and approaches (especially catalytic systems for polymer synthesis), new polymer materials originating from new monomers or comonomers, chemical modifications of polymers, etc.

Prof. Dr. Haiyang Gao
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. International Journal of Molecular Sciences is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. There is an Article Processing Charge (APC) for publication in this open access journal. For details about the APC please see here. Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • polymer synthesis
  • polymer chemistry
  • coordination polymerization
  • organometallic catalysts
  • polyolefin
  • degradable polymer materials
  • green and sustainable polymeric materials
  • homogeneous polymerization
  • heterogeneous polymerization.

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Related Special Issue

Published Papers (9 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Jump to: Review

16 pages, 3276 KiB  
Article
Tough Bioplastics from Babassu Oil-Based Acrylic Monomer, Hemicellulose Xylan, and Carnauba Wax
by Yehor Polunin, Vasylyna Kirianchuk, Najah Mhesn, Liying Wei, Sergiy Minko, Igor Luzinov and Andriy Voronov
Int. J. Mol. Sci. 2023, 24(7), 6103; https://doi.org/10.3390/ijms24076103 - 23 Mar 2023
Cited by 4 | Viewed by 1939
Abstract
We describe here the fabrication, characterization, and properties of tough bioplastics made of a babassu oil-based acrylic polymer (PBBM), hemicellulose xylan grafted with PBBM chains, and carnauba wax (CW). The plastic was primarily designed to obtain bioderived materials that can replace low-density polyethylene [...] Read more.
We describe here the fabrication, characterization, and properties of tough bioplastics made of a babassu oil-based acrylic polymer (PBBM), hemicellulose xylan grafted with PBBM chains, and carnauba wax (CW). The plastic was primarily designed to obtain bioderived materials that can replace low-density polyethylene (LDPE) in certain food packaging applications. To obtain plastic, the radical polymerization of an original babassu oil-based acrylic monomer (BBM) in the presence of xylan macromolecules modified with maleic anhydride (X-MA) was conducted. The polymerization resulted in a material (PBBM-X) mostly consisting of highly branched PBBM/X-MA macromolecules. PBBM-X has a glass transition of 42 °C, a storage modulus of 130 MPa (at 25 °C, RT), and a Young’s modulus of 30 MPa at RT. To increase the moduli, we blended PBBM-X with carnauba wax, a natural material with a high modulus and a melting temperature of ~80 °C. It was found that PBBM-X is compatible with the wax, as evidenced by the alternation of the material’s thermal transitions and the co-crystallization of BBM side alkyl fragments with CW. As a result, the PBBM-X/CW blend containing 40% of the wax had a storage modulus of 475 MPa (RT) and a Young’s modulus of 248 MPa (RT), which is close to that of LDPE. As polyethylene, the PBBM-X and PBBM-X/CW bioplastics have the typical stress-strain behavior demonstrated by ductile (tough) plastics. However, the bioplastic’s yield strength and elongation-at-yield are considerably lower than those of LDPE. We evaluated the moisture barrier properties of the PBBM-X/(40%)CW material and found that the bioplastic’s water vapor permeability (WVP) is quite close to that of LDPE. Our bioderived material demonstrates a WVP that is comparable to polyethylene terephthalate and lower than the WVP of nylon and polystyrene. Taking into account the obtained results, the fabricated materials can be considered as polyethylene alternatives to provide sustainability in plastics production in the packaging areas where LDPE currently dominates. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Figure 1

12 pages, 10535 KiB  
Article
Amphiphilic Polyethylene-b-poly(L-lysine) Block Copolymer: Synthesis, Self-Assembly, and Responsivity
by Lixia Pei, Hongyu Ma, Yan Jiang, Handou Zheng and Haiyang Gao
Int. J. Mol. Sci. 2023, 24(6), 5495; https://doi.org/10.3390/ijms24065495 - 13 Mar 2023
Cited by 5 | Viewed by 1878
Abstract
Polyethylene-b-polypeptide copolymers are biologically interesting, but studies of their synthesis and properties are very few. This paper reports synthesis and characterization of well-defined amphiphilic polyethylene-block-poly(L-lysine) (PE-b-PLL) block copolymers by combining nickel-catalyzed living ethylene polymerization with controlled ring-opening [...] Read more.
Polyethylene-b-polypeptide copolymers are biologically interesting, but studies of their synthesis and properties are very few. This paper reports synthesis and characterization of well-defined amphiphilic polyethylene-block-poly(L-lysine) (PE-b-PLL) block copolymers by combining nickel-catalyzed living ethylene polymerization with controlled ring-opening polymerization (ROP) of ε-benzyloxycarbonyl-L-lysine-N-carboxyanhydride (Z-Lys-NCA) and sequential post-functionalization. Amphiphilic PE-b-PLL block copolymers self-assembled into spherical micelles with a hydrophobic PE core in aqueous solution. The pH and ionic responsivities of PE-b-PLL polymeric micelles were investigated by means of fluorescence spectroscopy, dynamic light scattering, UV-circular dichroism, and transmission electron microscopy. The variation of pH values led to the conformational alteration of PLL from α-helix to coil, thereby changing the micelle dimensions. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Graphical abstract

13 pages, 3336 KiB  
Article
Fabrication of Polyurethane Elastomer/Hindered Phenol Composites with Tunable Damping Property
by Xiuying Zhao, Ruiheng Jin, Zhihao Niu, Yangyang Gao and Shikai Hu
Int. J. Mol. Sci. 2023, 24(5), 4662; https://doi.org/10.3390/ijms24054662 - 28 Feb 2023
Cited by 3 | Viewed by 2037
Abstract
Vibration and noise-reduction materials are indispensable in various fields. Polyurethane (PU)-based damping materials can dissipate the external mechanical and acoustic energy through molecular chain movements to mitigate the adverse effects of vibrations and noise. In this study, PU-based damping composites were obtained by [...] Read more.
Vibration and noise-reduction materials are indispensable in various fields. Polyurethane (PU)-based damping materials can dissipate the external mechanical and acoustic energy through molecular chain movements to mitigate the adverse effects of vibrations and noise. In this study, PU-based damping composites were obtained by compositing PU rubber prepared using 3-methyltetrahydrofuran/tetrahydrofuran copolyether glycol, 4,4′-diphenylmethane diisocyanate, and trimethylolpropane monoallyl ether as raw materials with hindered phenol, viz., and 3,9-bis{2-[3-(3-tert-butyl-4-hydroxy-5-methylphenyl)proponyloxy]-1,1-dimethylethyl}-2,4,8,10-tetraoxaspiro[5.5]undecane (AO-80). Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, and tensile tests were conducted to evaluate the properties of the resulting composites. The glass transition temperature of the composite increased from −40 to −23 °C, and the tan δMax of the PU rubber increased by 81%, from 0.86 to 1.56 when 30 phr of AO-80 was added. This study provides a new platform for the design and preparation of damping materials for industrial applications and daily life. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Figure 1

15 pages, 4309 KiB  
Article
Biodegradable Scaffolds for Vascular Regeneration Based on Electrospun Poly(L-Lactide-co-Glycolide)/Poly(Isosorbide Sebacate) Fibers
by Monika Śmiga-Matuszowicz, Jakub Włodarczyk, Małgorzata Skorupa, Dominika Czerwińska-Główka, Kaja Fołta, Małgorzata Pastusiak, Małgorzata Adamiec-Organiściok, Magdalena Skonieczna, Roman Turczyn, Michał Sobota and Katarzyna Krukiewicz
Int. J. Mol. Sci. 2023, 24(2), 1190; https://doi.org/10.3390/ijms24021190 - 7 Jan 2023
Cited by 4 | Viewed by 1984
Abstract
Vascular regeneration is a complex process, additionally limited by the low regeneration potential of blood vessels. Hence, current research is focused on the design of artificial materials that combine biocompatibility with a certain rate of biodegradability and mechanical robustness. In this paper, we [...] Read more.
Vascular regeneration is a complex process, additionally limited by the low regeneration potential of blood vessels. Hence, current research is focused on the design of artificial materials that combine biocompatibility with a certain rate of biodegradability and mechanical robustness. In this paper, we have introduced a scaffold material made of poly(L-lactide-co-glycolide)/poly(isosorbide sebacate) (PLGA/PISEB) fibers fabricated in the course of an electrospinning process, and confirmed its biocompatibility towards human umbilical vein endothelial cells (HUVEC). The resulting material was characterized by a bimodal distribution of fiber diameters, with the median of 1.25 µm and 4.75 µm. Genotyping of HUVEC cells collected after 48 h of incubations on the surface of PLGA/PISEB scaffolds showed a potentially pro-angiogenic expression profile, as well as anti-inflammatory effects of this material. Over the course of a 12-week-long hydrolytic degradation process, PLGA/PISEB fibers were found to swell and disintegrate, resulting in the formation of highly developed structures resembling seaweeds. It is expected that the change in the scaffold structure should have a positive effect on blood vessel regeneration, by allowing cells to penetrate the scaffold and grow within a 3D structure of PLGA/PISEB, as well as stabilizing newly-formed endothelium during hydrolytic expansion. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Graphical abstract

18 pages, 4175 KiB  
Article
Double Stimuli-Responsive di- and Triblock Copolymers of Poly(N-isopropylacrylamide) and Poly(1-vinylimidazole): Synthesis and Self-Assembly
by Elena Yu. Kozhunova, Anna V. Plutalova, Andrey V. Sybachin, Alexander V. Chertovich and Elena V. Chernikova
Int. J. Mol. Sci. 2023, 24(1), 879; https://doi.org/10.3390/ijms24010879 - 3 Jan 2023
Viewed by 2444
Abstract
For the first time, double stimuli-responsive properties of poly(N-isopropylacrylamide) (PNIPA) and poly(1-vinylimidazole) (PVIM) block copolymers in aqueous solutions were studied. The synthesis of PNIPA60-b-PVIM90 and PNIPA28-b-PVIM62-b-PNIPA29 was performed using [...] Read more.
For the first time, double stimuli-responsive properties of poly(N-isopropylacrylamide) (PNIPA) and poly(1-vinylimidazole) (PVIM) block copolymers in aqueous solutions were studied. The synthesis of PNIPA60-b-PVIM90 and PNIPA28-b-PVIM62-b-PNIPA29 was performed using reversible addition–fragmentation chain transfer (RAFT) polymerization. The polymers were characterized by size exclusion chromatography and 1H NMR spectroscopy. The conformational behavior of the polymers was studied using dynamic light scattering (DLS) and fluorescence spectroscopy (FS). It was found that PNIPA and block copolymers conformation and ability for self-assembly in aqueous medium below and above cloud point temperature depend on the locus of hydrophobic groups derived from the RAFT agent within the chain. Additionally, the length of PVIM block, its locus in the chain and charge perform an important role in the stabilization of macromolecular micelles and aggregates below and above cloud point temperature. At 25 °C the average hydrodynamic radius (Rh) of the block copolymer particles at pH 3 is lower than at pH 9 implying the self-assembling of macromolecules in the latter case. Cloud points of PNIPA60-b-PVIM90 are ~43 °C and ~37 °C at a pH of 3 and 9 and of PNIPA28-b-PVIM62-b-PNIPA29 they are ~35 °C and 31 °C at a pH of 3 and 9. Around cloud point independently of pH, the Rh value for triblock copolymer rises sharply, achieves the maximum value, then falls and reaches the constant value, while for diblock copolymer, it steadily grows after reaching cloud point. The information about polarity of microenvironment around polymer obtained by FS accords with DLS data. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Figure 1

10 pages, 2316 KiB  
Article
Photoluminescent Polymer Aerogels with R, G and B Emission
by Loredana Stan, Teodor Malutan, Irina Volf, Marcel Popa, Camelia E. Tincu and Corneliu S. Stan
Int. J. Mol. Sci. 2022, 23(24), 16004; https://doi.org/10.3390/ijms232416004 - 15 Dec 2022
Cited by 3 | Viewed by 1767
Abstract
In this work, three new polymer aerogels based on 2-hydroxy ethyl methacrylate (HEMA) complexes with Eu(III), Tb(III) and La(III) are prepared and investigated. The polymer aerogels present strong photoluminescence with emissions located in the red, green and blue regions of the visible spectrum. [...] Read more.
In this work, three new polymer aerogels based on 2-hydroxy ethyl methacrylate (HEMA) complexes with Eu(III), Tb(III) and La(III) are prepared and investigated. The polymer aerogels present strong photoluminescence with emissions located in the red, green and blue regions of the visible spectrum. Depending on the water content used during the preparation path, the consistency of the photoluminescent aerogels varies from rigid, regularly shaped monoliths to a flexible, fibrous material with very low density. The morpho-structural investigation was performed by FT-IR, XPS and SEM. Thermal behavior was also evaluated, while steady-state fluorescence spectroscopy, absolute PLQY and lifetime were used for the investigation of their luminescent properties. The impressive photoluminescent emission located in the red, green and blue areas of the visible spectrum is preserved irrespective of the selected porosity. Their photo-emissive properties, tunable porosity and the convenience of the preparation path could be some arguments for applications as photonic conversion mediums in special-purpose optoelectronic devices or sensors. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Graphical abstract

13 pages, 3872 KiB  
Article
Optical and Flame-Retardant Properties of a Series of Polyimides Containing Side Chained Bulky Phosphaphenanthrene Units
by Mihaela Homocianu, Diana Serbezeanu, Gabriela Lisa, Mihai Brebu and Tăchiță Vlad-Bubulac
Int. J. Mol. Sci. 2022, 23(21), 13174; https://doi.org/10.3390/ijms232113174 - 29 Oct 2022
Cited by 5 | Viewed by 1803
Abstract
Among the multitude of polymers with carbon-based macromolecular architectures that easily ignite in certain applications where short circuits may occur, polyimide has evolved as a class of polymers with high thermal stability while exhibiting intrinsic flame retardancy at elevated temperatures via a char-forming [...] Read more.
Among the multitude of polymers with carbon-based macromolecular architectures that easily ignite in certain applications where short circuits may occur, polyimide has evolved as a class of polymers with high thermal stability while exhibiting intrinsic flame retardancy at elevated temperatures via a char-forming mechanism. However, high amounts of aromatic rings in the macromolecular backbone are required for these results, which may affect other properties such as film-forming capacity or mechanical properties; thus, much work has been done to structurally derivatize or make hybrid polyimide systems. In this respect, flexible polyimide films (PI(1–4)) containing bulky 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) units have been developed starting from commercial dianhydrides and an aromatic diamine containing two side chain bulky DOPO groups. The chemical structure of PI(1–4)) was characterized by 1H NMR, 13C NMR and 31P NMR spectroscopy. The optical properties, including absorption and luminescence spectra of these polymers, were analyzed. All polyimides containing DOPO derivatives emitted blue light with an emission maxima in the range of 340–445 nm, in solvents such as N,N-dimethylformamide, N-methyl-2-pyrrolidone, chloroform, and N,N-dimethylacetamide, while green light emission (λem = 487 nm for PI-4) was evidenced in a thin-film state. The thermal decomposition mechanism and flame-retardant behavior of the resulting materials were investigated by pyrolysis-gas-chromatography spectrometry (Py-GC), scanning electron microscopy (SEM), EDX maps and FTIR spectroscopy. The residues resulting from the TGA experiments were examined by SEM microscopy images and FTIR spectra to understand the pyrolysis mechanism. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Figure 1

Review

Jump to: Research

15 pages, 1924 KiB  
Review
Microbial Synthesis of High-Molecular-Weight, Highly Repetitive Protein Polymers
by Juya Jeon, Shri Venkatesh Subramani, Kok Zhi Lee, Bojing Jiang and Fuzhong Zhang
Int. J. Mol. Sci. 2023, 24(7), 6416; https://doi.org/10.3390/ijms24076416 - 29 Mar 2023
Cited by 10 | Viewed by 3677
Abstract
High molecular weight (MW), highly repetitive protein polymers are attractive candidates to replace petroleum-derived materials as these protein-based materials (PBMs) are renewable, biodegradable, and have outstanding mechanical properties. However, their high MW and highly repetitive sequence features make them difficult to synthesize in [...] Read more.
High molecular weight (MW), highly repetitive protein polymers are attractive candidates to replace petroleum-derived materials as these protein-based materials (PBMs) are renewable, biodegradable, and have outstanding mechanical properties. However, their high MW and highly repetitive sequence features make them difficult to synthesize in fast-growing microbial cells in sufficient amounts for real applications. To overcome this challenge, various methods were developed to synthesize repetitive PBMs. Here, we review recent strategies in the construction of repetitive genes, expression of repetitive proteins from circular mRNAs, and synthesis of repetitive proteins by ligation and protein polymerization. We discuss the advantages and limitations of each method and highlight future directions that will lead to scalable production of highly repetitive PBMs for a wide range of applications. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Graphical abstract

24 pages, 2620 KiB  
Review
Polyphosphazene-Based Biomaterials for Biomedical Applications
by Geun-Woo Jin, N. Sanoj Rejinold and Jin-Ho Choy
Int. J. Mol. Sci. 2022, 23(24), 15993; https://doi.org/10.3390/ijms232415993 - 15 Dec 2022
Cited by 7 | Viewed by 2919
Abstract
Recently, synthetic polymers have attracted great interest in the field of biomedical science. Among these, polyphosphazenes (PPZs) are regarded as one of the most promising materials, due to their structural flexibility and biodegradability compared to other materials. PPZs have been developed through numerous [...] Read more.
Recently, synthetic polymers have attracted great interest in the field of biomedical science. Among these, polyphosphazenes (PPZs) are regarded as one of the most promising materials, due to their structural flexibility and biodegradability compared to other materials. PPZs have been developed through numerous studies. In particular, multi-functionalized PPZs have been proven to be potential biomaterials in various forms, such as nanoparticles (NPs) and hydrogels, through the introduction of various functional groups. Thus, PPZs have been applied for the delivery of therapeutic molecules (low molecular weight drugs, genes and proteins), bioimaging, phototherapy, bone regeneration, dental liners, modifiers and medical devices. The main goal of the present review is to highlight the recent and the most notable existing PPZ-based biomaterials for aforementioned applications, with future perspectives in mind. Full article
(This article belongs to the Special Issue Synthesis of Advanced Polymer Materials)
Show Figures

Figure 1

Back to TopTop