Search Results (34)

Herein, we present the analysis, design, optimization, and fabrication of a broadband, stepped-impedance Wilkinson power divider. The proposed structure employs stepped-impedance transmission lines and open-circuited stubs, achieving a simple and compact implementation while maintaining a wideband frequency response. Initially, transmission-line-based circuit analysis was performed to extract the design equations, followed by simulation and optimization to enhance impedance matching and output-port isolation over a broad bandwidth. Finally, the proposed divider was fabricated using microstrip-line technology, and experimental measurements were conducted using the Agilent E5071C vector network analyzer. The simulation and measurement results showed efficient wideband operation over the 1–4 GHz frequency range. Specifically, the measured return loss at the input port was <−10 dB; the corresponding return loss at the output ports was <−15 dB. The measured insertion loss was −3.73 ± 0.42 dB. The isolation between the output ports was <−10 dB, reaching approximately −30 dB at 2.1 GHz and −25 dB at the center operating frequency (f₀ = 2.5 GHz). The amplitude and phase imbalances were 0 ± 0.2 dB and 0^o ± 0.8^o, respectively. Furthermore, the overall size of the proposed wideband Wilkinson power divider was 0.35λg × 0.21λg. Compared to previous designs, the divider proposed in this study exhibits an improved and more symmetric frequency response, as well as a substantially reduced size, making it suitable for several modern wireless technologies such as Wi-Fi, Bluetooth, GPS, DCS, WCDMA, and sub-6 GHz 5G communication systems. Full article

This paper proposes a compact UHF microstrip divider with wideband harmonic suppression. A combined resonator, formed by a T-shaped resonator and a pair of coupled compact microstrip resonant cells (CCMRCs), is embedded into each divider branch to replace the conventional quarter-wavelength transmission lines. The divider is designed on an FR4 substrate (ε_r = 4.4, thickness = 60 mil) for a center frequency of 570 MHz. Full-wave electromagnetic simulations indicate equal power division at 570 MHz with return loss better than 39 dB and output-port isolation higher than 47 dB. Moreover, a wide stopband from 1.5 GHz to 3.5 GHz is obtained, yielding strong attenuation for the third-to-sixth harmonics. The proposed layout occupies 19.6 mm × 21.6 mm, which is about 76% smaller than a conventional 570 MHz divider (42.7 mm × 41 mm). The proposed design is suitable for modern wireless communication systems. Full article

This paper describes the status of developing Josephson arbitrary waveform synthesizer (JAWS) chips at NIM (National Institute of Metrology, China). To obtain high junction integration density and fewer data input channels, the chip employs an on-chip Wilkinson power divider and inside/outside dc blocks, enabling both arrays to be driven by a single pulse-generator channel. In addition, the tapered coplanar waveguide structure is used to ensure the microwave uniformity of the long-junction array. Each array consisted of 4000 double-stack Nb/Nb_xSi_1−x/Nb junctions, and 16,000 junctions are integrated in the chip in total. The JAWS chip demonstrates good performance, capable of synthesizing a 300 mV root mean square (rms) voltage with exceptionally low harmonic distortion. Dc and ac voltage-current characteristics measurements indicate that the junctions are with a critical current of 2.5 mA, and a normal-state resistance of 4.5 mΩ per junction. Contact aligners are manually operated to fabricate the chips, and process errors in the fabrication are estimated in this paper. Full article

This paper provides a comprehensive review of recent advancements in radio-frequency (RF) multifunctional components with integrated filtering characteristics, including tunable filtering attenuators, filtering power dividers, filtering couplers, and filtering Butler matrices, all of which play critical roles in wireless communication systems. With the increasing demand for miniaturization, integration, and low-loss performance in RF front-ends, multifunctional components with filtering characteristics have become essential. This review first introduces tunable attenuators and filtering attenuators based on various technologies such as PIN diodes, graphene-based structures, and RF-MEMS switches, and also analyzes their advantages, limitations, and performance. Then, we discuss filtering power dividers developed from Wilkinson structures, three-line coupled structures, resonator-based coupling matrix methods, and SSPP-waveguide hybrids. Furthermore, filtering couplers and filtering Butler matrices are reviewed, highlighting their capability to simultaneously achieve amplitude and phase control, making them suitable for multi-beam antenna feeding networks. Finally, a brief conclusion is summarized. Future research directions, such as hybrid technologies, novel materials, broadband and multi-band designs, and antenna-matrix co-design, are suggested to further enhance the performance and practicality of multifunctional RF components for next-generation wireless communication systems. Full article

This paper presents a microstrip active quasi-circulator designed for low-power wireless communication systems. The circuit consists of a second-order Wilkinson power divider and two power amplifiers with high gain and ultra-low noise characteristics. By leveraging the unidirectional transmission characteristics of the transistors and the isolation provided by resistors within the power divider, the interference between the transmitter (TX) and receiver (RX) is effectively suppressed. Additionally, thanks to the dual-amplifier architecture, no extra power amplification circuitry is required, thereby reducing the overall complexity and power consumption of the communication system. The detailed design procedure of the proposed quasi-circulator is presented. The measurement results show that, within the frequency range of 4.75 GHz to 6.11 GHz, the isolation between the TX and RX ports exceeds 20 dB, the return loss at each port is greater than 10 dB, and the transmission gains from the TX port to the antenna and from the antenna to the RX port are 3.1–8.7 dB and 2.7–4.0 dB, respectively, demonstrating a relative bandwidth of 25%. Full article

This paper presents a Ka-band cylindrical conformal transceiver active phased array (CCTAPA) with a full-azimuth scanning gain fluctuation of 0.8 dB and low power consumption. The array comprises 20 panels of 4 × 4 antenna elements, RF beam-control circuits, a Wilkinson power divider network, and frequency converters. The proposed three-subarray architecture enables ±9° beam scanning with minimal gain degradation. By dynamically switching subarrays and transceiver channels across azimuthal directions, the array achieves full 360° coverage with low gain fluctuation and power consumption. Fabrication and testing demonstrate a gain fluctuation of 0.8 dB, equivalent isotropically radiated power (EIRP) between 50.6 and 51.3 dBm, and a gain-to-noise-temperature ratio (G/T) ranging from −8 dB/K to −8.5 dB/K at 28.5 GHz. The RF power consumption remains below 8.73 W during full-azimuth scanning. This design is particularly suitable for airborne platforms requiring full-azimuth coverage with stringent power budgets. Full article

This paper introduces a compact multi-stage Wilkinson power divider/combiner (WPDC) topology which enables broadband operation with isolation capacitors and requiring only one single isolation resistor. The application of an L network for even-mode impedance matching and a π network for odd-mode impedance matching results in a more compact circuit layout and lower insertion loss compared to conventional WPDC designs. A K- and Ka-band WPDC is designed using a 45RFE process with measurements verifying the proposed topology. The results of a two-stage WPDC show an insertion loss below 0.7 dB, isolation better than 20 dB, and input/output return loss exceeding 12 dB across the frequency range of 18.6 to 33.6 GHz. The corresponding amplitude imbalance is within 0.06 dB, and the phase difference is below 0.8 degrees. The core chip size is 210 μm × 186 μm, which is only 0.018 λ₀ × 0.016 λ₀ at the center frequency of 26.1 GHz. Thus, this integrated passive component holds significant promise as a viable solution for wideband applications. Full article

This work presents two Wilkinson power dividers (WPDs) using multi-layer pseudo coplanar waveguide (PCPW) structures. The PCPW-based WPDs were designed, implemented, and verified in a standard 180 nm CMOS process. The proposed PCPW features high slow-wave and low-loss performances compared to other common transmission lines. The two WPDs are based on the same PCPW structure parameters in terms of line width, spacing, and used metal layers. One WPD was realized in a straight PCPW-based layout, and the other WPD was realized in a meandered PCPW-based layout. Both the two WPDs worked up to V-band frequencies, as expected, which also demonstrates that the PCPW guiding structure is less susceptible to the effects of meanderings on the propagation constant and characteristic impedance. The meandered design shows that the measured insertion losses were about 5.1 dB, and its return losses were better than 17.5 dB at 60 GHz. In addition, its isolation, amplitude imbalance, and phase imbalance were 18.5 dB, 0.03 dB, and 0.4°, respectively. The core area was merely 0.2 mm × 0.23 mm, or 1.8 × 10⁻³λ_o². Full article

An efficient design method for a compact and ultra-wideband multi-stage Wilkinson power divider in a parallel stripline (PSL) is proposed. To enhance the frequency bandwidth of the proposed power divider while reducing its size, the isolation branch is modified; that is, two capacitors are connected to both sides of a resistor at each isolation branch. For an efficient design process, the PSL power divider is equivalently represented by two microstrip power dividers, and the design equations are derived. Based on the design equations, an in-house algorithm is utilized to optimally determine the design parameters, including the line impedance, resistance, and capacitance of each stage. For example, a three-stage PSL power divider is designed with three $\lambda /4$ transmission lines at a base frequency of 5 GHz. To verify the accuracy of the design procedure, 3D EM simulations and measurements are performed, and the results show good agreement. Compared with the conventional three-stage Wilkinson power divider, the proposed PSL power divider achieves a wider frequency bandwidth of 1.16 to 6.51 GHz (139.5%) and a 23% shorter transmission line length of 207°, while exhibiting an insertion loss of 0.7 to 1.4 dB. Full article

In this study, at ultra-wideband (UWB) frequency band (3.1–10.6 GHz), we propose the use of compact 2:1 and 3:1 nonuniform transmission line Wilkinson power dividers (NTL WPDs) as feeding networks for simple 2 × 1 linear UWB Vivaldi tapered and nonuniform slot antenna (VTSA and VNSA) arrays. The 2:1 and 3:1 tapered transmission line (TTL) WPDs are designed and tested in this work as benchmarks for NTL WPDs. The VTSA array provides measured S₁₁ < −10.28 dB at 2.42–11.52 GHz, with a maximum gain of 8.61 dBi, which is 24.39% higher than the single element. Using the VNSA array, we achieve 52% compactness and 6.76% bandwidth enhancement, with good measured results of S₁₁ < −10.2 dB at 3.24–13 GHz and 15.11% improved gain (8.14 dBi) compared to the VNSA single element. The findings show that the NTL and Vivaldi nonuniform slot profile antenna (VNSPA) theories are successful at reducing the size of the UWB WPD and VTSA without sacrificing performance. They also emphasize the Vivaldi antenna’s compatibility with other circuits. These compact arrays are ideal for high-resolution medical applications like breast cancer detection (BCD) because of their high gain, wide bandwidth, directive stable radiation patterns, and low specific absorption rate (SAR). A simple BCD simulation scenario is addressed in this work. Detailed parametric studies are performed on the two arrays for impedance-matching enhancement. The computer simulation technology (CST) software is used for the simulation. Hardware measurement results prove the validity of the proposed arrays. Full article

This paper proposes a harmonic-suppressed Wilkinson power divider (HS WPD) utilizing parallel resonant shunt stubs (PRSSs). PRSSs are integrated into the conventional WPD by adding functionalities such as bandpass filtering, harmonic suppression, and physical port separation. The resonance conditions and design equations of the PRSS are theoretically derived and verified through circuit simulations. Using the PRSS, we designed an HS WPD operating at 1 GHz. The fabricated HS WPD demonstrated an insertion loss of 3.2 dB at the fundamental frequency, with a wide 3 dB bandwidth of 129%. The harmonic suppression levels at the 2nd and 3rd harmonic frequencies are measured to be 21.0 dB and 25.8 dB, respectively. The measured input return loss at the fundamental frequency was 27.9 dB, whereas the output return loss was 24.6 dB. Additionally, the HS WPD demonstrates isolation levels at the fundamental, 2nd, and 3rd harmonic frequencies, with levels of 29.2 dB, 17.8 dB, and 47.1 dB, respectively. It also exhibited broadband isolation (>8.7 dB) across the frequency range of 100 kHz to 3.35 GHz. The PRSS design allows for the physical separation of the ports without requiring additional circuitry. Compared to previously reported PDs, the proposed design offers multiple functions in a compact size, making it highly suitable for various microwave systems. Full article

In this paper, a high-efficiency GaN Doherty power amplifier (DPA) for 5G applications in the N78 sub-6 GHz band is introduced. The theoretical analysis of the matching networks for the peak and carrier transistors is presented, with a focus on the impact of unequal power splitting for both transistors and the recommendation of a post-harmonic suppression network. The proposed design features an unequal Wilkinson power divider at the input and a post-harmonic suppression network at the output, both of which are crucial for achieving high efficiency. The Doherty power amplifier comprises two GaN 10 W HEMTs, measured across the 3.3 GHz to 3.8 GHz band (the N78 band), and the results reveal significant improvements in gain, output power, drain efficiency, and power-added efficiency. Specifically, the proposed design achieved a power gain of over 12 dB and 42 dBm saturated output power. It also achieved a drain efficiency of 80% at saturation and a power-added efficiency of 75.2%. Furthermore, the proposed harmonic suppression network effectively attenuated the harmonics at the output of the amplifier from the second to the fourth order to more than −50 dB, thus enhancing the device’s linearity. Full article

This paper introduces a novel algorithm for designing a low-pass filter (LPF) and a microstrip Wilkinson power divider (WPD) using a neural network surrogate model. The proposed algorithm is applicable to various microwave devices, enhancing their performance and frequency response. Desirable output parameters can be achieved for the designed LPF and WPD by using the proposed algorithm. The proposed artificial neural network (ANN) surrogate model is employed to calculate the dimensions of the LPF and WPD, resulting in their efficient design. The LPF and WPD designs incorporate open stubs, stepped impedances, triangular-shaped resonators, and meandered lines to achieve optimal performance. The compact LPF occupies a size of only 0.15 λg × 0.081 λg, and exhibits a sharp response within the transmission band, with a sharpness parameter of approximately 185 dB/GHz. The designed WPD, operating at 1.5 GHz, exhibits outstanding harmonics suppression from 2 GHz to 20 GHz, with attenuation levels exceeding 20 dB. The WPD successfully suppresses 12 unwanted harmonics (2nd to 13th). The obtained results demonstrate that the proposed design algorithm effectively accomplishes the LPF and WPD designs, exhibiting desirable parameters such as operating frequency and high-frequency harmonics suppression. The WPD demonstrates a low insertion loss of 0.1 dB (S₂₁ = 0.1 dB), input and output return losses exceeding 30 dB (S₁₁ = −35 dB, S₂₂ = −30 dB), and an output ports isolation of more than 32 dB (S₂₃ = −32 dB), making it suitable for integration into modern communication systems. Full article

In this paper, new single/double-layer N-way Wilkinson power dividers (WPDs) were designed by using slow-wave structures such as narrow-slit-loaded and meandered transmission lines. For size reduction, the slit-loaded and meandered lines were used instead of the quarter-wavelength transmission lines of a conventional WPD. Based on the proposed approaches, two-, four-, and eight-way power dividers were designed, simulated, and fabricated. The fabricated 2-, 4-, and 8-way circuits were measured at the center frequencies of 2.03, 1.77, and 1.73 GHz, which are in excellent agreement with the predicted ones. The meandered transmission lines were also used to design WPD types with novel input/output port arrangements. For this purpose, two three-way WPDs were located on both sides of the same board to have different power-splitting ratios at different inputs and outputs in order to provide alternative solutions for antenna arrays. Furthermore, a five-way dual-layer WPD was introduced by locating the meandered transmission lines into two layers. The most important advantage of the proposed 3- and 5-way WPDs is that they allowed the input power at the next output port to be halved, in the order of P/2, P/4, P/8, P/16, and P/16. All the designed power-halving WPDs were simulated, fabricated, and successfully tested. Full article

In this paper, a dual-polarized omnidirectional rectenna array using a hybrid power-combining scheme is proposed for the applications of RF energy harvesting. In the antenna design part, two omnidirectional antenna subarrays are created to receive horizontally polarized electromagnetic (EM) waves and a four-dipole subarray is produced to receive vertically polarized incoming EM waves. The two antenna subarrays of different polarizations are combined and optimized, so as to reduce the mutual influence between them. In this way, a dual-polarized omnidirectional antenna array is realized. In the rectifier design part, a half-wave rectifying structure is adopted for converting the RF energy into DC energy. Based on the Wilkinson power divider and 3-dB hybrid coupler structure, a power-combining network is designed to connect the whole antenna array and rectifiers. The proposed rectenna array is fabricated and measured under different RF energy harvesting scenarios. All simulated and measured results are in good agreement, which verifies the capabilities of the designed rectenna array. Full article