Search Results (322)

Analyzing the two-phase flow behavior in bearing lubrication is crucial for understanding friction and wear mechanisms, optimizing lubrication design, and improving bearing operational efficiency and reliability. However, the complexity of oil–air two-phase flow in high-speed bearings poses significant research challenges. Currently, there is a lack of comparative studies employing different simulation strategies to address this issue, leaving a gap in evidence-based guidance for selecting appropriate simulation approaches in practical applications. This study begins with a comparative analysis between experimental and simulation results to validate the reliability of the adopted simulation approach. Subsequently, a comparative evaluation of different simulation methods is conducted to provide a scientific basis for relevant decision-making. Evaluated from three dimensions—adaptability to rotational speed conditions, research focuses (oil distribution and power loss), and computational economy—the findings reveal that FVM excels at medium-to-high speeds, accurately predicting continuous oil film distribution and power loss, while MPS, leveraging its meshless Lagrangian characteristics, demonstrates superior capability in describing physical phenomena under extreme conditions, albeit with higher computational costs. Economically, FVM, supported by mature software ecosystems and parallel computing optimization, is more suitable for industrial design applications, whereas MPS, being more reliant on high-performance hardware, is better suited for academic research and customized scenarios. The study further proposes that future research could adopt an FVM-MPS coupled approach to balance efficiency and precision, offering a new paradigm for multi-scale lubrication analysis in bearings. Full article

Background/Objectives: Spacer dislocation is among the most frequent mechanical complications after revision total hip arthroplasty for periprosthetic hip infection. Spacer dislocations may be managed conservatively, but there are no guidelines on the rehabilitation of these patients, and the restriction of weight bearing is still under debate. Methods: We first report the case of a patient with hip spacer cranial dislocation, judged unfit to be surgically treated once more for a medium period, who started a rehabilitation program with partial weight bearing. Results: After two weeks of inpatient rehabilitation, the patient started to maintain the standing position with partial weight bearing on the affected side. Following hospital discharge we continued rehabilitation in the outpatient clinic. Despite the finding of the denervation of the ipsilateral quadriceps, three months after admission, she was able to walk for short distances using a walker, initially with the help of a therapist and then with supervision. About one year later, she was able to undergo the reimplantation of the definitive prosthesis. Conclusions: Despite the spacer dislocation, walking short distances is a feasible goal, even with assistance, wearing a brace and using a walker. Future research is needed to confirm and expand upon this observation and to understand the mechanisms underlying the development of neurological complications to implement effective prevention strategies. Full article

This study analyzes 209 dog skeletons from two sites in Wolin (9th–mid-13th century AD) using 100 standard metric variables covering cranial, mandibular, and postcranial elements. Estimated withers height, body mass, age at death, and sex were derived using established methods. The results indicate the presence of at least two to three morphotypes: small spitz-like dogs (40–50 cm, 4–6 kg), medium brachycephalic forms (50–60 cm, 10–15 kg), and larger mesocephalic individuals (up to 65 cm, 20–40 kg). Dogs lived 3–10 years, with both sexes represented. Signs of cranial trauma and dental wear suggest utilitarian roles such as guarding. The size range and morphological diversity point to intentional breeding and trade-based importation. Small dogs likely served as companions or city guards, while medium and large types were used for herding, hunting, or transport. These findings highlight Wolin’s role as a dynamic cultural and trade center, where human–dog relationships were shaped by anthropogenic selection and regional exchange. Full article

The continuous need for simplified, minimally invasive restorative procedures with a high precision has led to the advancement of highly filled flowable resin-based materials. These materials present excellent initial outcomes in various clinical applications, including the injection molding technique. Given that several clinical reports present signs of wear and staining, this systematic review aims to investigate the mechanical and optical properties of highly filled flowable composite resins. A comprehensive literature research was conducted to identify relevant studies from the PubMed, the Cochrane Library, and Scopus databases. Data extraction and screening was performed by two independent evaluators. Both in vitro studies and clinical trials were included. A total of thirty-one studies were included in this review. A total of 27 in vitro studies investigated highly filled flowable composite resins independently, or in comparison with conventional composite resins, traditional flowable composites, bulk-fill flowable composites, glass ionomer cements, and compomers. Additionally, four randomized controlled clinical trials (RCTs) compared highly filled flowable composite resins with their conventional counterparts. Highly filled flowable composite resins exhibit adequate optical properties. Despite their significant improvements, their mechanical properties remain inferior to those of medium-viscosity composite resins. These materials demonstrate a favorable initial performance in the injection molding technique. Based on a limited number of RCTs, these materials demonstrate an adequate performance in class I and II restorations; however these findings should be interpreted with caution. The reported drawbacks in laboratory studies may contraindicate their clinical application in extensive cavities, load-bearing areas, and in cases of excessive tooth wear and parafunctional activity. A careful clinical case selection is strongly recommended. Full article

This study examines the microstructural evolution, mechanical properties, and wear behavior of medium-carbon dual-phase steel (AISI 1040) processed via Multi-Axis Compression (MAC). The DP steel was produced through inter-critical annealing at 745 °C, followed by MAC at 500 °C, resulting in a refined grain microstructure. Optical micrographs confirmed the presence of ferrite and martensite phases after annealing, with significant grain refinement observed following MAC. The average grain size decreased from 66 ± 4 μm to 18 ± 1 μm after nine MAC passes. Mechanical testing revealed substantial improvements in hardness (from 145 ± 9 HV to 298 ± 18 HV) and ultimate tensile strength (from 557 ± 33 MPa to 738 ± 44 MPa), attributed to strain hardening and the Hall–Petch effect. Fractographic analysis revealed a ductile failure mode in the annealed sample, while DP0 and DP9 exhibited a mixed fracture mode. Both DP0 and DP9 samples demonstrated superior wear resistance compared to the annealed sample. However, the DP9 sample exhibited slightly lower wear resistance than DP0, likely due to the fragmentation of martensite induced by high accumulated strain, which could act as crack initiation sites during sliding wear. Furthermore, wear resistance was significantly enhanced due to the combined effects of the DP structure and Severe Plastic Deformation (SPD). These findings highlight the potential of MAC processing for developing high-performance steels suitable for lightweight automotive applications. Full article

The present study focused on a comparative analysis of NaOH-treated and untreated Sida acuta fiber-reinforced composites with respect to their wear behavior and compressive strength. The Sida acuta fibers were treated with 5% NaOH, while the untreated fibers were used directly as reinforcement, both comprising 32 ± 1 wt.% of the epoxy matrix composites. The composites were further characterized based on their average density, hardness, and compressive strength. Additionally, weight loss, volume loss, and wear rate were examined under dry wear test conditions across various loads and sliding velocities. The results indicate that the alkali-treated fiber-reinforced composite exhibits superior hardness (84.3 ± 2.0) and compressive strength (99.89 ± 3.92 MPa), representing improvements of 12.57% and 13.5%, respectively, over the untreated fiber-reinforced composite. Moreover, the 5% NaOH-treated fiber-reinforced composite demonstrated lower wear rates compared to its untreated counterpart. Scanning Electron Microscopy (SEM) was employed to examine the dry wear surface morphology of both composite laminates, providing insights that support the observed test results. Overall, the developed Sida acuta composite exhibits promising properties, making it suitable for lightweight and medium-strength structural applications. Full article

The integration of acoustic emission (AE) signals into adaptive control systems for CNC wood milling represents a promising advancement in intelligent manufacturing. This study investigated the feasibility of using AE signals for the real-time monitoring and control of CNC milling processes, focusing on medium-density fiberboard (MDF) as the workpiece material. AE signals were captured using dual-channel sensors during side milling on a five-axis CNC machine, and their characteristics were analyzed across varying spindle speeds and feed rates. The results showed that AE signals were sensitive to changes in machining parameters, with higher spindle speeds and feed rates producing increased signal amplitudes and distinct frequency peaks, indicating enhanced cutting efficiency. The statistical analysis confirmed a significant relationship between AE signal magnitude and cutting conditions. However, limitations related to material variability, sensor configuration, and the narrow range of process parameters restrict the broader applicability of the findings. Despite these constraints, the results support the use of AE signals for adaptive control in wood milling, offering potential benefits such as improved machining efficiency, extended tool life, and predictive maintenance capabilities. Future research should address signal variability, tool wear, and sensor integration to enhance the reliability of AE-based control systems in industrial applications. Full article

This study investigates the tribocorrosion behavior of 304 stainless steel (304SS), S31254 super austenitic stainless steel (S31254 SASS), and a medium-entropy austenitic stainless steel (MEASS) in 3.5 wt.% NaCl solution under sliding conditions. The objective is to clarify the performance differences among these alloys when exposed to simultaneous mechanical wear and corrosion. Electrochemical techniques, including potentiodynamic polarization and potentiostatic sliding tests, were used to evaluate corrosion resistance and repassivation behavior. Quantitative analysis based on ASTM G119 revealed that MEASS showed a 68% lower total material loss compared to 304SS and a 55% lower loss compared to S31254. MEASS also exhibited the lowest corrosion current density (1.46 μA/cm²) under tribocorrosion conditions, representing an 83% reduction compared to 304SS. These improvements are attributed to the higher chromium and nickel contents of MEASS, which enhance passive film stability and reduce susceptibility to localized corrosion. The results demonstrate that MEASS offers superior resistance to combined mechanical and corrosive degradation in chloride-containing environments. Full article

In this study, 20 wt.% of Nb was incorporated into a CrFeNi medium-entropy alloy (MEA) powder system to prepare CrFeNi-Nb composite coatings on a Q235B mild steel substrate by laser cladding technology. The effects of Nb addition on the phase composition, microstructure, and wear resistance of CrFeNi coatings were systematically investigated. Microstructural characterization revealed that the CrFeNi coating exhibited a single face-centered cubic (FCC) phase structure, while the CrFeNi-Nb composite coating demonstrated a dual-phase structure comprising FCC phase and Laves phase. The Laves phase significantly enhanced the microhardness and wear resistance of the coating. The average microhardness of the CrFeNi-Nb coating increased by 259.62% compared to the substrate and 190.58% compared to the Nb-free CrFeNi coating. The average coefficient of friction (COF) of the coating decreased from 0.74 to 0.68; the wear rate reduced from 5.77 × 10⁻⁴ mm³ N⁻¹ m⁻¹ to 2.26 × 10⁻⁴ mm³ N⁻¹ m⁻¹; and the weight loss decreased from 10.77 mg to 4.3 mg. The experimental results demonstrated that the addition of Nb promoted the formation of the Laves phase in the CrFeNi MEA, which effectively improved the wear resistance of the coating. Full article

This study aims to investigate the wear and corrosion–wear behavior of 17-4PH stainless steel specimens, both fabricated via Selective Laser Melting (SLM) and conventional bulk material, after undergoing Solution Treatment (S.T.) in a seawater medium. Microstructural observations indicated that solution treatment contributed to a more uniform distribution of martensitic structures on the sample surface. Moreover, the solution-treated specimens exhibited improved microstructural uniformity and structural stability. SLM specimens exhibit the elimination of fine particles and scanning track traces. Based on the results of dynamic polarization tests, SLM specimens demonstrate superior corrosion resistance. However, in corrosion–wear conditions, the bulk material outperforms the SLM specimens, primarily due to the presence of pores in the latter, which are detrimental under such environments. XPS analysis of the passive film structure indicates that the passive layer is mainly composed of FeO, Cr₂O₃, and NiO, with the inner layer predominantly consisting of chromium oxide. The Cr₂O₃ layer, formed by the reaction between chromium and oxygen, significantly enhances the corrosion resistance of the material due to its extremely low chemical reactivity and high stability. Full article

This study evaluates the wear and corrosion resistance of the Cu-50Ni-5Al alloy reinforced with CeO₂ nanoparticles for potential use as anodes in molten carbonate fuel cells (MCFCs). Cu–50Ni–5Al alloys were synthesized, with and without the incorporation of 1% CeO₂ nanoparticles, by the mechanical alloying method and spark plasma sintering (SPS). The samples were evaluated using a single scratch test with a cone-spherical diamond indenter under progressive normal loading conditions. A non-contact 3D surface profiler characterized the scratched surfaces to support the analysis. Progressive loading tests indicated a reduction of up to 50% in COF with 1% NPs, with specific values drop-ping from 0.48 in the unreinforced alloy to 0.25 in the CeO₂-doped composite at 15 N of applied load. Furthermore, the introduction of CeO₂ decreased scratch depths by 25%, indicating enhanced wear resistance. The electrochemical behavior of the samples was evaluated by electrochemical impedance spectroscopy (EIS) in a molten carbonate medium under a H₂/N₂ atmosphere at 550 °C for 120 h. Subsequently, the corrosion products were characterized using X-ray diffraction (XRD), scanning electron microscopy coupled with energy dispersive spectroscopy (SEM-EDS), and X-ray photoelectron spectroscopy (XPS). The results demonstrated that the CeO₂-reinforced alloy exhibits superior electro-chemical stability in molten carbonate environments (Li₂CO₃-K₂CO₃) under an H₂/N₂ atmosphere at 550 °C for 120 h. A marked reduction in polarization resistance and a pronounced re-passivation effect were observed, suggesting enhanced anodic protection. This effect is attributed to the formation of aluminum and copper oxides in both compositions, together with the appearance of NiO as the predominant phase in the materials reinforced with nanoparticles in a hydrogen-reducing atmosphere. The addition of CeO₂ nanoparticles significantly improves wear resistance and corrosion performance. Recognizing this effect is vital for creating strategies to enhance the material’s durability in challenging environments like MCFC. Full article

Efficient coal grinding is a crucial aspect of the energy and mining industries. However, traditional grinding methods are known to be energy-intensive and cause significant wear on equipment as well as negative environmental impacts due to the release of small particles that can harm air quality and affect human health. In response to these challenges, we are conducting research to develop an electric pulse device for coal grinding. This device will use high-voltage discharges in a liquid medium to create shock waves that selectively destroy coal particles while minimizing mechanical damage. The electric pulse installation consisted of a control unit (for monitoring the operating modes of the installation), a generator (for converting the AC input voltage into DC output voltage), a capacitor (for energy storage), a protection system (for shutting down the installation in cases when a voltage exceeding the set safe operating discharge voltage occurs on the capacitor), a spark gap (forming a gap consisting of two conductive hemispherical electrodes separated by an air gap, designed to form an electric spark between conductors), and an electric pulse grinding device. The input material for each experiment had consistent parameters: the coal particles were diameter 8–10 mm and weighed 400 g. Coal was processed using the electric pulse method with various voltage values, numbers of pulses, capacitor capacities, and pulse frequencies. The yield of the final product depended on these parameters, and effective settings for producing coal powder were identified. The research results demonstrate that a flat metal mesh plate is effective as the negative electrode in the electric pulse grinding device. Full article

In this work, 1,3-diketone synthesized via the Claisen condensation method and nano-copper particles modified by the Brust–Schiffrin method were added into a commercial marine medium-speed diesel engine cylinder piston oil to evaluate their effects on boundary lubrication performance. Friction and wear tests conducted on CKS-coated piston ring and cast-iron cylinder liner samples demonstrated significant reductions in both friction and wear with the addition of 1,3-diketone and nano-copper particles. Compared to the original oil without additives, the friction force was reduced by up to 16.7%, while the wear of the piston ring and cylinder liner was decreased by up to 21.6% and 15.1% at 150 °C, respectively. A worn surface analysis indicated that the addition of 1,3-diketone and functionalized nano-copper particles influenced the depolymerization and tribo-chemical reactions of the anti-wear additive ZDDP (zinc dialkyldithiophosphate) in the original engine oil. This modification enhanced the oil’s anti-friction and anti-wear properties, offering valuable insights into the development of eco-friendly lubricants for energy-efficient systems. Full article

This article presents the simulation results of synchronization of a permanent magnet synchronous generator (PMSG) dedicated for a hydroelectric plant without power converter devices. The proposed machine design allows to connect a generator to the grid in two different ways. With the first method, the machine is connected to the grid in a similar way as in the case of an electrically excited synchronous generator. The second method is a direct line-start process based on asynchronous torque—similar to asynchronous motor start. Both methods can be used alternately. The advantages of the presented design are elimination of converter devices for starting the PMSG, possibility of use in small and medium hydroelectric power plants, operation with a high efficiency and high power factor in a wide range of generated power, and smaller dimensions in comparison to the generators currently used. The described rotor design allows for the elimination of capacitor batteries for compensation of reactive power drawn by induction generators commonly used in small hydroelectric plants. In addition, due to the high efficiency of the PMSG, high power factor, and appropriately selected design, the starting current during synchronization is smaller than in the case of an induction generator, which means that the structural elements wear out more slowly, and thus, the generator’s service life is increased. In this work, it is shown that PMSG with a rotor cage should have permanent magnets with an increased temperature class in order to avoid demagnetization of the magnets during asynchronous start-up. In addition, manufacturers of such generators should provide the number of start-up cycles from cold and warm states in order to avoid shortening the service life of the machine. The main objective of the article is to present the methods of synchronizing a generator of such a design (a rotor with permanent magnets and a starting cage) and their consequences on the behavior of the machine. The presented design allows synchronization of the generator with the network in two ways. The first method enables synchronization of the generator with the power system by asynchronous start-up, i.e., obtaining a starting torque exceeding the braking torque from the magnets. The second method of synchronization is similar to the method used in electromagnetically excited generators, i.e., before connecting, the rotor is accelerated to synchronous speed by means of a water turbine, and then, the machine is connected to the grid by switching on the circuit breaker. This paper presents electromagnetic phenomena occurring in both cases of synchronization and describes the influence of magnet temperature on physical quantities. Full article

Postural balance deteriorates as heel height increases, but the dual-task interference effect has not been investigated. This observational cross-sectional study investigated the influence of two concurrent cognitive tasks on balance performance while wearing shoes with different heel heights. We hypothesized that the concurrent cognitive demands’ effect on balance deterioration would be more pronounced in shoes with increased heel height. Twenty-one women (21–54 years) were assessed for quiet stance balance performance while wearing shoes with low-, medium-and high-heel height. Cognitive interference on balance performance was investigated by a dual-task condition using a short memory (COGN_A) and verbal fluency (COGN_B) task. Balance performance was quantified by measuring center of pressure (CoP) path length and sway range, while errors made and scores in COGN_A and COGN_B assessed cognitive performance. Postural balance decreased as heel height increased with greater CoP path length and anteroposterior sway for the medium- and high-heeled shoes (p < 0.001). Cognitive load did not affect balance performance (p = 0.234–0.494), nor was there an interaction between cognitive load and balance with increasing heel height (p = 0.281–0.375). The results suggest that cognitive load does not limit postural balance with increasing heel height, and that balance is more affected by the increased mechanical demands of heel height. Full article