Search Results (11)

Osseodensification (OD) has emerged as a favorable osteotomy preparation technique that preserves and compacts autogenous bone along the osteotomy walls during site preparation, enhancing primary stability and implant osseointegration. While OD has demonstrated promising results in low-density trabecular bone, especially when used in conjunction with acid-etched (AE) implant surfaces, its efficacy in high-density cortical bone remains unclear—particularly in the context of varying implant surface characteristics. In this study, Grade V titanium alloy implants (Ti-6Al-4V, 4 mm × 10 mm) with deep threads, designated bone chambers and either as-machined (Mach) or AE surfaces were placed in 3.8 mm diameter osteotomies in the submandibular region of 16 adult sheep using either OD or conventional (Reg) drilling protocols. Insertion torque values (N·cm) were measured at the time of implant placement to evaluate primary stability. Mandibles were harvested at 3-, 6-, 12-, or 24-weeks post-implantation (n = 4 sheep/time point), and histologic sections were analyzed to quantify bone-to-implant contact (BIC) and bone area fractional occupancy (BAFO). Qualitative histological analysis confirmed successful osseointegration among all groups at each of the healing time points. No statistically significant differences were observed between OD and conventional drilling techniques in insertion torque (p > 0.628), BIC (p > 0.135), or BAFO (p > 0.060) values, regardless of implant surface type or healing interval. The findings indicate that neither drilling technique nor implant surface treatment significantly influences osseointegration in high density cortical bone. Furthermore, as the osteotomy was not considerably undersized, the use of OD instrumentation showed no signs of necrosis, inflammation, microfractures, or impaired osseointegration in dense cortical bone. Both OD and Reg techniques appear to be suitable for implant placement in dense bone, allowing flexibility based on surgeon preference and clinical circumstances. Full article

Considering the global increase in fish consumption, the growing side-streams coming from the fish supply chain (e.g., skin, fins, tail, heads…), also including undersized or “unwanted catches”, have been recently proposed as source of high-value bioactive compounds (e.g., peptides and fatty acids). In this case study, hydrolyzed collagen peptides (HCPs) were extracted from different parts of Mugil cephalus L. using environmentally friendly techniques such as ultrasounds and enzymatic treatments. Both a mixed biomass derived from the skin, fins, and tail, and a whole fish, were considered as starting biomass, simulating the unsorted processing side-streams and an undersized/unwanted catch, respectively. The extracted HCPs were purified in fractions (<3 KDa and >3 KDa) whose yields (about 5% and 0.04–0.3%, respectively) demonstrated the efficiency of the hydrolysis process. The extraction protocol proposed allowed us to also isolate the intermediate products, namely the lipids (about 8–10%) and the non-collagenous proteins (NCs, 16–23%), whose exploitation could be considered. Each sample was characterized using Sircol, UltraViolet-Spectra, and hydroxyproline assay, and the viability of their collagen fractions was tested on human endothelial cells. Significant effects were obtained at a fraction of <3 KDa, in particular at a concentration of 0.13 µg/mL. The T-scratch test was also performed, with positive results in all fractions tested. Full article

In a large-scale operation, feed ores are introduced into the AG/SAG mill in a continuous mode at a given flow rate to replace the discharging slurry. Nonetheless, the variations in the feed characteristics, typically hardness and size distribution, could cause sudden disruption to the mill operation. This would be challenging to detect in practice, owing to the hostile environment of the mill. In this work, an acoustic sensing-based monitoring technique was utilized in a laboratory-scale AG/SAG mill locked-cycle study to keep track of fluctuations caused by feed ore heterogeneity. Analysis of the recorded mill acoustic response using statistical root mean square (RMS) and mill discharge sizes showed that the introduction of fresh feed with varying hardness and size distribution considerably altered the mill product undersize of −150 μm and acoustic emission. Overall, the acoustic sensing technique demonstrated that the AG/SAG mill stability as well as disturbances caused by different feed size fractions and hardness can be monitored using the mill acoustic response, an indication of real-time monitoring and optimisation. Full article

Injecting low-cost semi-coke is critical to reducing blast furnace production costs. The combustion behavior of the co-injection of semi-coke and undersized coke powder is still rarely studied. In this work, a three-dimensional CFD mathematical model was established to simulate the gas velocity, temperature, composition distribution and burnout of semi-coke during the combustion of pulverized semi-coke. The influence of mass fraction of semi-coke on the composition and burnout in the combustion zone of blast furnace was also studied. The results show that the maximum concentrations of CO and H₂ in the combustion zone are 36% and 8%, respectively. With the decrease of the semi-coke ratio in the blended coal, the fixed carbon content and the calorific value of the blended coal increase, but the burnout of the blended coal reduces. When bituminous coal is single injected, the burnout reaches 70%, which is higher than that of semi-coke. In actual production, for the semi-coke and coke powder injecting into the blast furnace, a proportion of bituminous coal can be appropriately added to improve the burnout rate of the coal blends and increase the H₂ content in reducing gas. Full article

Application of additives to waste may influence the course of the biostabilization process and contribute to its higher effectiveness, as well as to a reduction in greenhouse gas and ammonia (NH₃) emission from this process. This paper presents research on the impact of biochar addition on the course of the biostabilization process of an undersized fraction from municipal solid waste (UFMSW) in terms of temperature changes, CO₂ concentration in the exhaust gases, NH₃ emission from the process, as well as changes in the carbon and nitrogen content in the processed waste. Six different biochar additives and three different air-flow rates were investigated for 21 days. It was found that biochar addition contributes to extending the thermophilic phase duration (observed in the case of the addition of 3% and 5% of biochar). The concentration of CO₂ in exhaust gases was closely related to the course of temperature changes. The highest concentration of CO₂ in the process gases (approx. 18–19%) was recorded for the addition of 10% and 20% of biochar at the lowest air-flow rate applied. It was found that the addition of 3% or a higher amount of biochar reduces nitrogen losses in the processed UFMSW and reduces NH₃ emission by over 90% compared to the control. Full article

The separation of graphite from cathode active materials containing Co, Ni, and Mn, and the metals Cu and Al by flotation was tested and evaluated with a black mass sample of crushed spent Li-ion batteries. The metals, Cu and Al, were mostly (>90%) concentrated by sieving into an oversize fraction (+0.25 mm). Graphite and the cathode active materials in the oversize fraction (+0.25 mm) were effectively separated from the metals, Cu and Al, by flotation. Pre-treatment by roasting at a temperature of 350–450 °C improved the flotation efficiency of graphite from the cathode active materials for the undersize fraction (−0.25 mm). Full article

In the Marche Region (Central Italy), the residual municipal waste (RMW) is commonly processed in mechanical biological treatment (MBT) systems. In these systems, following a first mechanical selection, the undersize organic fraction from RMW (us-OFRMW) undergoes a partial aerobic biological treatment before being landfilled as a biostabilised fraction (bios-OFRMW) without dedicated energy or material recovery. Alternative us-OFRMW management scenarios have been elaborated for this region, at both present (reference year 2019) and future (reference year 2035) time bases. In the first scenario, the potential bioenergy recovery through anaerobic digestion (AD) from the us-OFRMW was evaluated. The second scenario aimed at evaluating the residual methane generation expected from the bios-OFRMW once landfilled, thus contributing also to the potential environmental impact connected with landfill gas (LFG) diffuse emissions from the regional landfills. The diversion to AD, at the present time, would allow a potential bioenergy recovery from the us-OFRMW equal to 4.35 MW_el, while the alternative scenario involves greenhouse gas (GHG) emissions equal to 195 kg CO₂ eq. per ton of deposited bios-OFRMW. In the future, the decreased amount of the us-OFRMW addressed to AD would still contribute with a potential bioenergy recovery of 3.47 MW_el. Full article

Mussel cultivation results in tons of by-product, with 27% of the harvest considered as reject material. In this study, mussel by-products considered to be undersized (mussels with a cooked meat yield <30%), mussels with broken shells and barnacle-fouled mussels were collected from three different locations in the west, north-west and south-west of Ireland. Samples were hydrolysed using controlled temperatures and agitation, and the proteolytic enzyme Protamex^® was added at an enzyme:substrate ratio of 1:50 (w:v). The hydrolysates were freeze-dried and analysed for protein content and amino acid composition, lipid content and fatty acid methyl ester (FAME) composition, ash and techno-functional and bioactive activities. The degree of hydrolysis was determined using the Adler-Nissen pH stat method and was found to be between 2.41% ± 0% and 7.55% ± 0.6%. Mussel by-products harvested between February and May 2019 had protein contents ranging from 36.76% ± 0.41% to 52.19% ± 1.78%. The protein content of mussels collected from July to October (the spawning season) ranged from 59.07% ± 1.375% to 68.31% ± 3.42%. The ratio of essential to nonessential amino acids varied from 0.68–0.96 and it was highest for a sample collected in November from the west of Ireland. All the hydrolysate samples contained omega-3 polyunsaturated fatty acids (PUFA), especially eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), which are known anti-inflammatory agents. Selected hydrolysates which had angiotensin-converting enzyme I (ACE-I; EC 3.4.15.1) and dipeptidyl peptidase IV (DPP-IV; EC 3.4.14.5) inhibitory activities were filtered using 3-kDa membrane filtration and the permeate fraction was sequenced using mass spectrometry (MS). Identified peptides were >7 amino acids in length. Following BIOPEP database mining, 91% of the by-product mussel peptides identified were found to be previously identified DPP-IV and ACE-I inhibitory peptides, and this was confirmed using in vitro bioassays. The ACE-I inhibitory activity of the by-product mussel hydrolysates ranged from 22.23% ± 1.79% to 86.08% ± 1.59% and the most active hydrolysate had an ACE-I inhibitory concentration (IC₅₀) value of 0.2944 mg/mL compared to the positive control, captopril. This work demonstrates that by-product mussel hydrolysates have potential for use as health-promoting ingredients. Full article

During the storage of spent polymer materials derived from municipal solid waste, which contain biodegradable impurities, an intense growth of microorganisms takes place. The aerobic metabolism of microorganisms may cause these materials to combust spontaneously and to become a real epidemiological risk for humans. The aim of the research is to determine the optimal addition of calcium oxide (CaO), which effectively reduces the number of selected microorganism groups populating the analyzed materials, in which spent polymers represent a significant fraction: refuse-derived fuel (RDF) and an undersize fraction of municipal solid waste (UFMSW). The main novelty of the experiments is to assess the benefits of using the commonly available and cheap filler (CaO), to hygienize the material and to reduce the fire hazard arising from its storage. During the mixing of spent polymer materials with pulverized CaO (mass shares: 1, 2, and 5% CaO), temperature changes were monitored using thermography. Moisture content (MC), pH, respiration activity (AT4) and bacterial count were determined before and after the experiment. During the addition of CaO (especially when the content was at 5%) to the UFMSW, higher maximum temperatures were obtained than in the case of RDF analyses, which may be the result of a high percentage of the biodegradable fraction and higher MC of the UFMSW. In all cases the waste temperature did not increase again after 3 min. CaO used in the experiment effectively limited the number of microorganisms. The addition of 5% of CaO has showed the strongest antimicrobial properties, and it can be recommended for hygienization of the analyzed materials and for the reduction of the risk of self-heating during their storage in windrows. Full article

In order to promote sustainable fishing practices within European fishing fleets and to avoid the large waste of valuable fish biomass through the practice of fish discarding, the new reform of the common fisheries policy includes the obligation of landing all species under total allowable catch (TAC) regulations. The new policy also prohibits the use of specimens under minimum conservation reference size for direct human cons38umption. In this context, it is necessary to find new uses for undersized fish, which might help to alleviate the costs associated with the landing obligation but without prompting the creation of a market. European hake (EH) (Merluccius merluccius), which is one of the most important commercial fish species for the Spanish fishing industry, with a total TAC for 2018 of 37,423 t, is used for this study. Consistent with the current policy framework and taking into account the commercial importance of this species, the aim of this work is to study a new strategy for the extraction of collagen from the skin and bone fraction of Merluccius merluccius undersized discards. Three collagen fractions are successfully isolated for the first time from the skin of M. merluccius skin and bone discarded raw material: acid-soluble collagen (ASC) fraction 1 and pepsin-soluble collagen (PSC) fraction 2 from the skin and ASC fraction 3 from bones. The total collagen yield of the process is 13.55 ± 3.18% in a dry basis (g collagen/100 g of skin and bone fraction (SBF)) and 47.80 ± 9.83% (g collagen/100 g of collagen determined by the hydroxyproline content in SBF). The three fractions are further characterized by using different physical and chemical analysis techniques, with the conclusion drawn that the triple helix structure is preserved in the three fractions, although ASC fractions (F1 and F3) present more or stronger hydrogen bonds than the PSC fraction (F2). With the process herein presented, deboned and skinned hake specimens could represent an interesting source of high quality type I collagen, which could be useful as a raw material for the biomedical, cosmetic, and nutraceutical industries. Full article

Background: The intraosseous temperature during implant installation has never been evaluated in an in vivo controlled setup. The aims were to investigate the influence of a drilling protocol and implant surface on the intraosseous temperature during implant installation, to evaluate the influence of temperature increase on osseointegration and to calculate the heat distribution in cortical bone. Methods: Forty Brånemark implants were installed into the metatarsal bone of Finnish Dorset crossbred sheep according to two different drilling protocols (undersized/non-undersized) and two surfaces (moderately rough/turned). The intraosseous temperature was recorded, and Finite Element Model (FEM) was generated to understand the thermal behavior. Non-decalcified histology was carried out after five weeks of healing. The following osseointegration parameters were calculated: Bone-to-implant contact (BIC), Bone Area Fraction Occupancy (BAFO), and Bone Area Fraction Occupancy up to 1.5 mm (BA1.5). A multiple regression model was used to identify the influencing variables on the histomorphometric parameters. Results: The temperature was affected by the drilling protocol, while no influence was demonstrated by the implant surface. BIC was positively influenced by the undersized drilling protocol and rough surface, BAFO was negatively influenced by the temperature rise, and BA1.5 was negatively influenced by the undersized drilling protocol. FEM showed that the temperature at the implant interface might exceed the limit for bone necrosis. Conclusion: The intraosseous temperature is greatly increased by an undersized drilling protocol but not from the implant surface. The temperature increase negatively affects the bone healing in the proximity of the implant. The undersized drilling protocol for Brånemark implant systems increases the amount of bone at the interface, but it negatively impacts the bone far from the implant. Full article