Search Results (37)

Alzheimer’s Disease (AD) is one of the most commonly seen neurodegenerative disorders, where early detection of its biomarkers is crucial for effective management. Conventional diagnostic methods are often expensive, time-consuming, and highly complex, which highlights an urgent need for point-of-care biosensing technology. In this work, we developed assays on three-dimensional (3D) graphene foam electrodes by functionalising them with a 1-Pyrenebutyric acid N-hydroxysuccinimide ester (Pyr-NHS) to enable effective antibody immobilisation for the detection of amyloid beta peptides (Aβ42 and Aβ40), key biomarkers for AD. Pyr-NHS linkers were used for stable functionalisation, followed by binding with Aβ42 and Aβ40 antibodies, and then bovine serum albumin (BSA) was employed as a blocking agent to minimise non-specific bindings on the electrode surface. Differential Pulse Voltammetry (DPV) measurements showed satisfactory stability over 12 days (RDS upper limit was <10%) and highly sensitive and specific detection of Aβ42 and Aβ40, with insignificant interference of tau217 protein. The biosensor exhibited a low limit of detection (LOD) with 252 aM for Aβ42 and 395 aM for Aβ40, covering 0.125 fM–1 nM and 0.125 fM–100 pM linear ranges, respectively. Further validation was conducted on spiked-diluted human plasma. This excellent analytical performance was attributed to the stable Pyr-NHS functionalisation, the 3D graphene foam enabling superior conductivity and a larger surface area on the working electrode, and the optimisation of antibody concentration for immobilisation. These promising results suggest that 3D graphene foam-based biosensors have considerable potential for early detection of AD biomarkers and developing cost-effective, portable, and reliable point-of-care devices. Full article

Graphitic nanomaterials have emerged as foundational components in nanoscience owing to their exceptional electrical, mechanical, and chemical properties, which can be tuned by controlling dimensionality and structural order. From zero-dimensional (0D) quantum dots, carbon nano-onions, and nanodiamonds to one-dimensional (1D) nanoribbons, two-dimensional (2D) nanowalls, and three-dimensional (3D) graphene foams, these architectures underpin advancements in catalysis, energy storage, sensing, and electronic technologies. Among various synthesis routes, chemical vapor deposition (CVD) provides unmatched versatility, enabling atomic-level control over carbon supply, substrate interactions, and plasma activation to produce well defined graphitic structures directly on functional supports. This review presents a comprehensive, dimension-resolved overview of CVD-derived graphitic nanomaterials, examining how process parameters such as precursor chemistry, temperature, hydrogen etching, and template design govern nucleation, crystallinity, and morphological evolution across 0D to 3D hierarchies. Comparative analyses of Raman, XPS, and XRD data are integrated to relate structural features with growth mechanisms and functional performance. By connecting mechanistic principles across dimensional scales, this review establishes a unified framework for understanding and optimizing CVD synthesis of graphitic nanostructures. It concludes by outlining a path forward for improving how CVD-grown carbon nanomaterials are made, monitored, and integrated into real devices so these can move from lab-scale experiments to practical, scalable technologies. Full article

The intensifying freshwater crisis underscores the critical need for all-weather, low-energy atmospheric water harvesting technologies. Inspired by the scale-like protrusions and interconnected channels of Tillandsia leaves that enable efficient water capture and release, a polyvinyl alcohol-based foam featuring a three-dimensional porous structure is fabricated using the supercritical carbon dioxide foaming technology. Compared to the traditional freeze-drying method, this approach significantly reduces preparation energy consumption and shortens the production cycle. Lithium chloride integration endows the foam with exceptional moisture absorption capacity, reaching 300% of its weight. Leveraging graphene’s outstanding photothermal conversion properties, the foam achieves a photothermal dehydration rate of 80.7% within 80 min under 1 Sun irradiation, demonstrating a rapid water release capacity. Furthermore, the polyvinyl alcohol-based foam exhibits no performance degradation after 60 cycles, indicating remarkable stability. This technology provides a scalable, low-cost, and all-climate-applicable solution for water-scarce regions. Full article

Thin films of manganese–nickel–cobalt oxide with graphene (G@MNCO) were deposited on copper foam using electrochemical deposition. NiCo₂O₄ is the main phase in these films. As the proportion of graphene in the precursor solution increases, the oxygen vacancies in the samples also increase. The microstructure of these samples evolves into hierarchical vertical flake structures. Cyclic voltammetry measurements conducted within the potential range of 0–1.2 V reveal that the electrode with the highest graphene content achieves the highest specific capacitance, approximately 475 F/g. Furthermore, it exhibits excellent cycling durability, maintaining 95.0% of its initial capacitance after 10,000 cycles. The superior electrochemical performance of the graphene-enhanced, manganese-doped nickel–cobalt oxide electrode is attributed to the synergistic contributions of the hierarchical G@MNCO structure, the three-dimensional Cu foam current collector, and the binder-free fabrication process. These features promote quicker electrolyte ion diffusion into the electrode material and ensure robust adhesion of the active materials to the current collector. Full article

The synergistic effect of CNT and three-dimensional N-doped graphene foam (3DNG) on improving corrosion resistance of zinc-reinforced epoxy (ZRE) composite coatings was studied in this work. Although CNT itself was demonstrated to be effective to promote the anti-corrosion performance of the ZRE coating, the incorporation of additional 3DNG leads to further enhancement of its corrosion resistance under the synergistic effect of the hybrid carbon nanofillers with different dimensions. Both the content of the carbonaceous fillers and the ratio between them affected the performance of the coating. The optimal content of hybrid filler in the coating was determined to be only 0.1% with 3DNG:CNT = 1:3. With the modification of hybrid fillers, the corrosion current of the coating could be reduced by more than six orders of magnitude. Additionally, the immersion test of the pre-scratched coating directly demonstrated the evident contribution of the hybrid fillers to the sacrificial anode-based surface protection mechanism of the coating. These results confirmed the synergistic effect of the hybrid 1D and 3D carbonaceous fillers on promoting the corrosion inhibition of their coating, which could be promising for application in other functional composites. Full article

Graphene foam composite is a promising candidate for advanced thermal management applications due to its excellent mechanical strength, high thermal conductivity, ultra-high porosity and huge specific surface area. In this study, a three-dimensional physical model was developed in accordance with the dodecahedral structure of graphene foam composite. A comprehensive numerical simulation was carried out to investigate the fluid flow and convective heat transfer in open-cell graphene foam composite by using ANSYS Fluent 2021 R1 commercial software. Research results show that, as porosity increases, the pressure gradient for graphene foam composite with circular and triangular cross-section struts is reduced by 65% and by 77%, respectively. At a given porosity of 0.904, when the inlet velocity increases from 1 m/s to 5 m/s, the pressure gradient is increased by 11.3 times and 13.8 times, and the convective heat transfer coefficient is increased by 54.5% and 43% for graphene foam composite with circular and triangular cross-section struts, respectively. Due to the irregularity of the skeleton distribution, the pressure drop in Y direction is the highest among the three directions, which is 8.7% and 17.4% higher than that in the Z and X directions at the inlet velocity of 5 m/s, respectively. The convective heat transfer coefficient in the Y direction is significantly lower than that along the X and Z directions. Furthermore, triangular cross-section struts induce a greater pressure drop but offer less effective heat transfer compared to circular struts. The research findings may provide critical insights into the design and optimization of graphene foam composites, and promote their potential for efficient thermal management and gas/liquid purification in engineering applications. Full article

The demand for regenerative energy and electric automotive applications has grown in recent decades. Supercapacitors have multiple applications in consumer alternative electronic products due to their excellent energy density, rapid charge/discharge time, and safety. CuFe₂O₄-incorporated three-dimensional graphene sheet (3DGS) nanocomposites were studied by different characterization studies such as X-ray diffraction, transmission electron microscopy, and scanning electron microscopy. The electrochemical studies were based on cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS) measurements. As prepared, 3DGS/CuFe₂O₄ nanocomposites exhibited an excellent surface area, high energy storage with appreciable durability, and excellent electrocatalysis properties. A supercapacitor with 3DGS/CuFe₂O₄-coated nickel foam (NF) electrodes exhibited an excellent specific capacitance of 488.98 Fg⁻¹, a higher current density, as well as a higher power density. After charge–discharge cycles in a 2.0 M KOH aqueous electrolyte solution, the 3DGS/CuFe₂O₄/NF electrodes exhibited an outstanding cyclic stability of roughly 95% at 10 Ag⁻¹, indicating that the prepared nanocomposites could have the potential for energy storage applications. Moreover, the 3DGS/CuFe₂O₄ electrode exhibited an excellent electrochemical detection of chloramphenicol with a detection limit of 0.5 µM, linear range of 5–400 µM, and electrode sensitivity of 3.7478 µA µM⁻¹ cm⁻². Full article

NiFe-layered double hydroxides (NiFe-LDH) have been reported to possess exceptional oxygen evolution reaction (OER) activity. However, maintaining the stability of high activity over a long time remains a critical challenge that needs to be addressed for their practical application. Here, we report a custom-sized deep recombination of 2D graphene oxide with NiFe-LDH (NiFe-LDH/GO/NF) through a simple electrodeposition method that improves OER activity and achieves excellent stability. The excellent performance of the catalyst mainly comes from the three-phase interface and electron transport channel dredged by the three-dimensional structure constructed by the deep composite, which can not only significantly reduce its charge and electron transfer resistance, improving the material conductivity, but it also effectively increases the specific surface area, inhibits aggregation, and exposes rich active sites. In addition, GO with good conductivity not only supports NiFe-LDH well but also increases the heterogeneous interface, putting the NiFe-LDH/GO composites in close contact with Ni foam and increasing the electrocatalytic stability of the NiFe-LDH/GO/NF. The experimental results show that the overpotential of NiFe-LDH/20,000GO/NF is only 295 mV at a current density of 100 mA cm⁻²; the Tafel slope is 52 mV dec⁻¹, and the charge transfer resistance (Rct) is only 0.601 Ω in 1 M KOH. This indicates that GO has excellent potential to assist in constructing geometric and electronic structures of NiFe-LDH in long-term applications. Full article

Supercapacitors have the characteristics of high power density, long cycle life, and fast charge and discharge rates, making them promising alternatives to traditional capacitors and batteries. The use of transition-metal compounds as electrode materials for supercapacitors has been a compelling research topic in recent years because their use can effectively enhance the electrical performance of supercapacitors. The current research on capacitor electrode materials can mainly be divided into the following three categories: carbon-based materials, metal oxides, and conductive polymers. Nickel hydroxide (Ni(OH)₂) is a potential electrode material for use in supercapacitors. Depending on the preparation conditions, two crystal phases of nickel hydroxide, α and β, can be produced. When compared to α-NiOH, the structure of β-Ni(OH)₂ does not experience ion intercalation. As a result, the carrier transmission rate of α-Ni(OH)₂ is slower, and its specific capacitance value is smaller. Its carrier transport rate can be improved by adding conductive materials, such as graphene. β-Ni(OH)₂ was chosen as an electrode material for a supercapacitor in this study. Homemade low-pressure chemical vapor deposition graphene (LPCVD-Graphene) conductive material was introduced to modify β-Ni(OH)₂ in order to increase its carrier transport rate. The LPCVD method was used to grow high-quality graphene films on three-dimensional (3D) nickel foam substrates. Then, a hydrothermal synthesis method was used to grow β-Ni(OH)₂ nanostructures on the 3D graphene/nickel foam substrate. In order to improve the electrical properties of the composite structure, a high-quality graphene layer was incorporated between the nickel hydroxide and the 3D nickel foam substrate. The effect of the conductive graphene layer on the growth of β-Ni(OH)₂, as well as its electrical properties and electrochemical performance, was studied. When this β-Ni(OH)₂/CVD-Graphene/3D-NF (nickel foam) material was used as the working electrodes of the supercapacitor under a current density of 1 A/g and 3 A/g, they exhibited a specific capacitance of 2015 F/g and 1218.9 F/g, respectively. This capacitance value is 2.62 times higher than that of the structure without modification with a graphene layer. The capacitance value remains at 99.2% even after 1000 consecutive charge and discharge cycles at a current density of 20 A/g. This value also improved compared to the structure without graphene layer modification (94.7%). Full article

Manganese-based bimetallic oxides show a high theoretical specific capacity, making them a potential next-generation lithium-ion battery anode material. However, as with metal oxide anode materials, aggregation, volume expansion, and poor conductivity are the main obstacles. In this manuscript, flexible CoMn₂O₄/graphene/carbon nanotube films were successfully prepared through a facile filtration strategy and a subsequent thermal treatment process. When used as anodes for lithium batteries, these films can be pressed onto nickel foam without other conductive additives and binders, which simplifies the manufacturing process. When used as an anode in the lithium-ion battery, CoMn₂O₄/GR/CNT film exhibits a high discharge capacity of 881 mAh g⁻¹ after 55 cycles. This value is ~2 times higher than the discharge capacity of CoMn₂O₄. The three-dimensional GR/CNT carrier effectively dispersed CoMn₂O₄, preventing its aggregation and alleviating the problem of volume expansion. Full article

The configuration of a continuous and oriented thermal pathway is essential for efficient heat dissipation in the oriented direction. Three-dimensional (3D) conductive filler structures provide a suitable approach for constructing continuous thermal pathways in polymer-based composites. The aluminum nitride/reduced graphene oxide/poly(dimethylsiloxane) (AlN/rGO/PDMS) composite material is made with a 3D foam structure and focuses on reducing GO and forming foam via polyvinyl alcohol (PVA). We analyze the successful fabrication of hybrid fillers and composites using various methods. The fabricated composite with a 3D network filler foam achieves a through-plane thermal conductivity of 1.43 W/mK and achieves 752% higher thermal conductivity compared to pure PDMS, which is superior to composites without 3D foam. The continuous 3D filler structure via freeze-drying and annealing processes provides efficient thermal dissipation in the through-plane direction pathway, which is critical for enhancing thermal conductivity. Therefore, this work produces a polymer composite material with improved thermal conductivity through various processes. Full article

Shape memory polymer (SMP) epoxy composites have attracted significant attention due to their easy processing, lightweight nature, and ability to recover strain. However, their limited recovery rate and inferior mechanical properties have hindered their functional applications. This research explores the potential of three-dimensional (3D) graphene foam (GrF) as a highly efficient reinforcement for SMP epoxy composites. We demonstrated that the incorporation of a mere 0.13 wt.% GrF into mold-cast SMP epoxy leads to a 19% increase in the glass transition temperature (T_g). To elucidate the reinforcing mechanism, we fabricated and extensively analyzed composites with varying weight percentages of GrF. The GrF-based SMP epoxy composite exhibits a 57% increase in thermal conductivity, measuring 0.296 W mK⁻¹ at 70 °C, due to the interconnected 3D graphene network within the matrix. Notably, this composite also demonstrates remarkable electrical conductivity, making it suitable for dual-triggering applications. The GrF-SMP epoxy composite achieves a maximum shape recovery ratio and a significant 23% improvement in the recovery rate, effectively addressing the issue of slow recovery associated with SMPs. We investigated the effect of switching temperatures on the shape recovery rate. We identified the optimal triggering temperature to initiate shape recovery for epoxy SMP and GrF-epoxy SMP as thermal energy equivalent to T_g + 20 °C. Additionally, we fabricated a bird-shaped composite using GrF reinforcement, which showcases self-healing capabilities through the crack opening and closure and serves as a tangible demonstration of the transformative potential of the composite. These GrF-epoxy SMP composites, responsive to stimuli, hold immense promise for diverse applications, such as mechanical systems, wearable sensors, morphing wings, foldable robots, and antennas. Full article

As a promising nano-porous material for energy dissipation, the viscoelastic properties of three-dimensional (3D) graphene foams (GrFs) are investigated by combining a dynamic mechanical analysis (DMA) and coarse-grained molecular dynamic (CGMD) simulations. The effects of the different factors, such as the density of the GrFs, temperature, loading frequency, oscillatory amplitude, the pre-strain on the storage and loss modulus of the GrFs as well as the micro-mechanical mechanisms are mainly focused upon. Not only the storage modulus but also the loss modulus are found to be independent of the temperature and the frequency. The storage modulus can be weakened slightly by bond-breaking with an increasing loading amplitude. Furthermore, the tensile/compressive pre-strain and density of the GrFs can be used to effectively tune the viscoelastic properties of the GrFs. These results should be helpful not only for understanding the mechanical mechanism of GrFs but also for optimal designs of advanced damping materials. Full article

A 3D hierarchical spherical honeycomb-like composite electrode materialof neodymium oxide (Nd₂O₃), cobalt tetraoxide (Co₃O₄), and reduced graphene oxide (rGO) on nickel foam (named as Nd₂O₃/Co₃O₄/rGO/NF) were successfully fabricated by combining the hydrothermal synthesis method and the annealing process. Nickel foam with a three-dimensional spatial structure was used as the growth substrate without the use of any adhesives. The Nd₂O₃/Co₃O₄/rGO/NF composite has outstanding electrochemical performance and can be used directly as an electrode material for supercapacitors (SCs). By taking advantage of the large specific surface area of the electrode material, it effectively slows down the volume expansion of the active material caused by repeated charging and discharging processes, improves the electrode performance in terms of electrical conductivity, and significantly shortens the electron and ion transport paths. At a 1 A/g current density, the specific capacitance reaches a maximum value of 3359.6 F/g. A specific capacitance of 440.4 F/g with a current density of 0.5A/g is still possible from the built symmetric SCs. The capacitance retention rate is still 95.7% after 30,000 cycles of testing at a high current density of 10 A/g, and the energy density is 88.1 Wh/kg at a power density of 300 W/kg. The outcomes of the experiment demonstrate the significant potential and opportunity for this composite material to be used as an electrode material for SCs. Full article

Direct, rapid, and sensitive detection of drugs in complex biological samples is essential for drug abuse control and health risk assessment. In this work, an electrochemical sensor was fabricated based on equipment of vertically-ordered mesoporous silica film (VMSF) on an electrochemically pre-treated three-dimensional graphene electrode (p-3DG), which can achieve direct and sensitive determination of methylthiopyridazine (TR) in urine. Three-dimensional graphene (3DG) with a continuous and interpenetrating graphene network was used as the supporting electrode and simple electrochemical polarization was employed to pre-treat 3DG to improve surface hydrophilicity and electrocatalytic performance. VMSF was easily grown using an electrochemical assisted self-assembly method within 10 s and was stably bound to the p-3DG surface. The nanochannel array on the as-prepared VMSF/p-3DG sensor enriched positively charged TR, leading to significantly improved electrochemical signal. Combined with the high electric activity of p-3DG and the enrichment of nanochannels, VMSF/p-3DG realized sensitive determination of TR ranging from 50 nM to 10 μM with a low detection limit (DL, 30 nM). Owing to the anti-fouling and anti-interference performance of VMSF, the common electroactive molecules including ascorbic acid (AA) and uric acid (UA) did not interfere with the detection. In addition, the detection of TR in buffer and urine exhibited similar sensitivity. Accurate detection of TR in urine was realized. Full article