Search Results (512)

High-entropy alloys (HEAs) represent a breakthrough class of materials characterized by a unique combination of properties derived from their multielement compositions. This review explores the current advancements in both electrochemical and electroless deposition techniques for synthesizing HEA thin films. This paper discusses the crucial plating conditions using aqueous or organic electrolytes and various current/potential modes that influence the formation, quality, and properties of these complex alloy coatings. Particular attention is given to their emerging applications in areas such as catalysis, protective coatings, microelectronics, and liquids’ separation. A comparison of electrochemical versus electroless methods reveals insights into the advantages and limitations of each technique for research and industrial use. This comprehensive review aims to guide further innovation in the development and application of HEA coatings. Full article

The rheological behavior of firefighting foam is the basis for analyzing foam flow and foam spreading. This experimental study investigates the complex rheological behavior of rapidly aging firefighting foams, specifically focusing on alcohol-resistant aqueous film-forming foam. The primary objective is to characterize the time-dependent viscoelasticity, yielding, and viscous flow of firefighting foam under controlled shear conditions, addressing the significant challenge posed by its rapid structural evolution (drainage and coarsening) during measurement. Using a cylindrical Couette rheometer, conductivity measurements for the liquid fraction, and microscopy for the bubble size analysis, the study quantifies how foam aging impacts key rheological parameters. The results show that the creep and relaxation response of the firefighting foam in the linear viscoelastic region conforms to the Burgers model. The firefighting foam shows ductile yielding and significant shear thinning, and its flow curve under slow shear can be well represented by the Herschel–Bulkley model. Foam drainage and coarsening have competitive effects on the rheology of the firefighting foam, which results in monotonic and nonmonotonic variations in the rheological response in the linear and nonlinear viscoelastic regions, respectively. The work reveals that established empirical relationships between rheology, liquid fraction, and bubble size for general aqueous foams are inadequate for firefighting foams, highlighting the need for foam-specific constitutive models. Full article

In high-pressure thermal power systems, corrosion-induced wall thinning in steam pipelines poses a significant threat to operational safety and efficiency. This study investigates the effects of gas–liquid two-phase flow on corrosion-induced wall thinning in pipe bends of high-pressure heaters in power plants, with particular emphasis on the mechanisms of void fraction and inner wall surface roughness. Research reveals that an increased void fraction significantly enhances flow turbulence and centrifugal effects, resulting in elevated pressure and Discrete Phase Model (DPM) concentration at the bend, thereby intensifying erosion phenomena. Simultaneously, the turbulence generated by bubble collapse at the bend promotes the accumulation and detachment of corrosion products, maintaining a cyclic process of erosion and corrosion that accelerates wall thinning. Furthermore, the increased surface roughness of the inner bend wall exacerbates the corrosion process. The rough surface alters local flow characteristics, leading to changes in pressure distribution and DPM concentration accumulation points, subsequently accelerating corrosion progression. Energy-Dispersive Spectroscopy (EDS) and Scanning Electron Microscopy (SEM) analyses reveal changes in the chemical composition and microstructural characteristics of corrosion products. The results indicate that the porous structure of oxide films fails to effectively protect against corrosive media, while bubble impact forces damage the oxide films, exposing fresh metal surfaces and further accelerating the corrosion process. Comprehensive analysis demonstrates that the interaction between void fraction and surface roughness significantly intensifies wall thinning, particularly under conditions of high void fraction and high roughness, where pressure and DPM concentration at the bend may reach extreme values, further increasing corrosion risk. Therefore, optimization of void fraction and surface roughness, along with the application of corrosion-resistant materials and surface treatment technologies, should be considered in pipeline design and operation to mitigate corrosion risks. Full article

Sparkling wine is a complex alcoholic beverage with high economic value, produced through a secondary fermentation of a still wine, followed by a prolonged aging period that may last from nine months to several years. With the growing global demand for high-quality sparkling wines, understanding the biochemical mechanisms related to aroma development has become increasingly relevant. This review provides a comprehensive overview of the secondary fermentation process, with particular emphasis on yeast selection, types of closure, and the impact of aging on the volatile composition. Special attention is also given to the analytical strategies employed for the identification and quantification of target compounds in sparkling wine matrices. Due to the presence of volatile compounds at trace levels, effective extraction and pre-concentration techniques are essential. Extraction methods such as solid-phase microextraction (SPME), stir-bar sorptive extraction (SBSE), and thin-film SPME (TF-SPME) are discussed, as well as chromatographic techniques, such as gas chromatography (GC) and liquid chromatography (LC). Full article

Batteries are used as energy storage devices in various equipment. Today, research is focused on solid-state batteries (SSBs), replacing the liquid electrolyte with a solid separator. The solid separators provide electrolyte stability, no leakage, and provide mechanical strength to the battery. Separators are mostly manufactured by either traditional processes or 3D printing technologies. These processes involve making a slurry of plastic, active and conductive material and usually adding a plasticizer when making thin films or filaments for 3D printing. This study investigates the additive manufacturing of solid-state electrolytes (SSEs) by employing fused deposition modeling (FDM) with recyclable, bio-derived polylactic acid (PLA) filaments. Precise control of macro-porosity is achieved by systematically varying key process parameters, including raster orientation, infill percentage, and interlayer adhesion conditions, thereby enabling the formation of tunable, interconnected pore networks within the polymer matrix. Following 3D printing, these engineered porous frameworks are infiltrated with lithium hexafluorophosphate (LiPF₆), which functions as the active ionic conductor. A tailored thermal sintering protocol is then applied to promote solid-phase fusion of the embedded salt throughout the macro-porous PLA scaffold, resulting in a mechanically robust and ionically conductive composite separator. The electrochemical ionic conductivity and structural integrity of the sintered SSEs are characterized through electrochemical impedance spectroscopy (EIS) and standardized mechanical testing to assess their suitability for integration into advanced solid-state battery architectures. The solid-state separator achieved an average ionic conductivity of 2.529 × 10⁻⁵ S·cm⁻¹. The integrated FDM-sintering process enhances ion exchange at the electrode–electrolyte interface, minimizes material waste, and supports cost-efficient, fully recyclable component fabrication. Full article

High permeance combined with high salt/dye separation efficiency is a prerequisite for achieving zero-liquid-discharge treatment of saline textile wastewater by membrane technology. Thin-film nanocomposite (TFN) membranes incorporating porous nanoparticles offer a promising route to overcome the permeability–selectivity trade-off of conventional polymer membranes. In this study, a vacuum-assisted method was used to co-blend ZIF-67 and SiO₂ nanoparticles, while branched polyethyleneimine (PEI) served as a cross-linking bridge, resulting in a high-performance TFN membrane for salt/dye separation. Acting as a molecular connector, PEI coordinated with ZIF-67 through metal–amine complexation and simultaneously formed hydrogen bonds with surface hydroxyl groups on SiO₂, thereby linking ZIF-67 and SiO₂. The resulting membrane exhibited good hydrophilicity and excellent dye separation performance (water flux = 359.8 L m⁻² h⁻¹ bar⁻¹; Congo Red rejection = 99.2%) as well as outstanding selectivity in dye/salt mixtures (Congo Red/MgCl₂ selectivity of 1094). The optimal ZIF@SiO₂-PEI membrane maintained stable dye rejection over a wide range of trans-membrane pressures, initial concentrations, and pH values. These results reveal the huge potential of applying the ZIF@SiO₂-PEI TFN membranes for resource recovery in sustainable textile wastewater systems. Full article

Recently, a new solarization method gained a great deal of attention thanks to various advantages in comparison with both the traditional one and soil fumigation (alternative soil treatment based on the use of chemical agents). This method implements traditional solarization by spraying a biodegradable black liquid over the soil surface before the application of a thermic film. This creates a thin black film that acts like a “black body”, significantly increasing soil temperatures at various depths. Thanks to higher temperatures, it is possible to eliminate most of the pathogens in shorter times compared to traditional solarization. In the present paper, the results of different trials carried out on green beans, Romanesco broccoli, and lettuce were reported. The aims of this work were to demonstrate the efficacy on soil borne pathogens, its lower impact on living soil fungal biodiversity and the agronomical performance of the new solarization method. All crops tested showed a significant yield increase when grown in soil treated with the innovative solarization method. Romanesco broccoli also exhibited improved inflorescence quality. Solarization had a positive impact on overall crop productivity: green beans showed a maximum yield increase of 165.3%, lettuce yields rose by 47.5%, and Romanesco broccoli yields were 111.5% higher compared to the non-solarized control. These results confirm that the new solarization method is more effective, as well as environmentally, economically, and socially sustainable compared to traditional methods. Full article

High-repetition-rate targets present an opportunity for developing diagnostic tools for on-demand calibration at high-power laser facilities for consistent performance and reproducibility during experimental campaigns. The non-linear change in transmission associated with a laser-driven plasma mirror, based on high-repetition rate targets, has been used in a Frequency Resolved Optical Gating (FROG) configuration to analyze the spectral phase for near-infrared pulses far from the Fourier limit. Three types of targets were compared for characterizing pulses in the 1–8 ps range: a glass slide, a polymer tape, and a thin liquid sheet created by two impinging micrometer-scale jets. The thin liquid film had the best mechanical stability and introduced the least spectral distortion, allowing the most robust reconstruction of the temporal intensity profile. The spectral phase was reconstructed using a non-iterative algorithm, which reproduced the second-order phase distortions induced with an acousto-optic programmable dispersive filter with an RMS error of 6.2%, leading to measured pulse durations with an RMS deviation ranging from 1% for pulses of 6.8–7.8 ps up to 7.5% for pulses around 1 ps. Full article

Biocompatible nanocarriers were formulated by encapsulating medicinal extracts from Bryonia dioica (Red Bryony) and Glaucium leiocarpum (Horned Poppy) using a nanophytosome approach. The nanophytosomes were prepared by employing a thin-film hydration technique. The SEM results showed a broad size distribution for both nanophytosomes, and the encapsulation efficiency was about 75–80% for both Red Bryony and Horned Poppy nanophytosomes, as confirmed through scanning electron microscopy (SEM) and dynamic light scattering (DLS). Zeta potential analysis indicated sufficient surface charges to maintain colloidal stability. Encapsulation improved the release characteristics of the extracts, exhibiting an initial burst release followed by sustained release, which is advantageous for enhancing bioavailability within a liquid environment. Fourier-transform infrared (FTIR) spectroscopy identified key functional groups, confirming the successful encapsulation of bioactive ingredients within the nanophytosomes. Cytotoxicity tests on fibroblast cell lines (HSF-PI 16) demonstrated the safety of these nanocarriers, indicating biocompatibility at concentrations up to 200 μg/mL. Stability tests over 30 days revealed minimal size fluctuations, further supporting the structural integrity of the formulations. Results suggest that the synthesized nanophytosomes could serve as effective and novel nanocarriers for herbal delivery, addressing the bioavailability limitations of herbal extracts and offering a promising approach for therapeutic applications in both traditional and alternative medicine. This is the first study to report nanophytosome-based delivery of Red Bryony and Horned Poppy extracts. Full article

The application of graphene nanoplatelets (GNPs) in polymer composites is a challenge due to their high tendency to agglomerate and restack during processing. In this work, alkyl phosphonium-based ionic liquid was used to assist the dispersion of GNP in an ethylene-vinyl acetate (EVA) matrix, through a melt-mixing procedure. The mechanical properties and creep resistance of the films prepared by the film extrusion process were evaluated. The results demonstrated that the noncovalent treatment of GNP with the ionic liquid (IL) enhanced the electrical conductivity and creep stability of the EVA composites. The microwave absorbing properties were studied in the X-band and Ku-band. A reflection loss (RL) of −15 dB for EVA containing 0.5 wt% of GNP and 1:1 wt% of GNP/IL was achieved. The use of a multi-layered structure containing thin film layers was efficient for enhancing the microwave absorbing performance, with a minimum RL of −24.6 dB and effective absorption bandwidth of 4.3 GHz. This result is attributed to the internal reflection and scattering of the radiation between layers. The use of simple, low-cost materials and procedures, combined with the system’s excellent mechanical and electrical properties, makes it a promising candidate for multifunctional applications as electrostatic dissipative and microwave absorbing materials for electronic packaging and other electronic devices. Full article

Poly-ether-ether-ketone (PEEK) is widely used in dynamic sealing applications due to its excellent properties. However, its tribological performance as a sealing material still has limitations, as its relatively high friction coefficient may lead to increased wear of sealing components, affecting sealing effectiveness and service life. To optimize its lubrication performance, this study employs surface modification techniques to synthesize a thin polyimide (PI) film on the surface of PEEK. When paired with bearing steel, this modification reduces the friction coefficient and enhances the anti-wear performance of sealing components. The tribological properties of a friction pair composed of GCr15 steel and PI-modified PEEK were systematically investigated using a nematic liquid crystal as the lubricant. The friction system was analyzed through various tests. The experimental results show that, under identical conditions, the friction coefficient of the PI-modified PEEK system decreased by 83.3% compared to pure PEEK. Under loads of 5 N and 25 N and rotational speeds ranging from 50 rpm to 400 rpm, the system exhibited induced alignment superlubricity. At 50 rpm, superlubricity was maintained when the load was below 105 N, while at 200 rpm, this occurred when the load was below 125 N. Excessively high rotational speeds (above 300 rpm) might affect system stability. The friction coefficient initially decreased and then increased with increasing load. The friction system demonstrated induced alignment superlubricity under the tested conditions, suggesting the potential application of PI-modified PEEK in friction components. Full article

Metalworking fluids (MWFs) are crucial in the manufacturing industry, playing a key role in facilitating various production processes. As each machining operation comes with distinct requirements, the properties of the MWFs have to be tailored to meet these specific demands. Understanding the properties of different MWFs is fundamental for optimizing processes and improving performance. This study centered on characterizing the thermal behavior of various cutting oils and water-based cutting fluids over a wide temperature range and sheds light on the specific tribological behavior. The results indicate that water-based fluids exhibit significant shear-thinning behavior, whereas cutting oils maintain nearly Newtonian properties. In terms of frictional performance, cutting oils generally provide better lubrication at higher temperatures, particularly in mixed and full-fluid film regimes, while water-based fluids demonstrate greater friction stability across a wider range of conditions. Among the tested fluids, water-based formulations showed a phase transition from solid to liquid near 0 °C due to their high water content, whereas only a few cutting oils exhibited a similar behavior. Additionally, the thermal conductivity and heat capacity of water-based fluids were substantially higher than those of the cutting oils, contributing to more efficient heat dissipation during machining. These findings, along with the reported data, intend to guide future researchers and industry in selecting the most appropriate cutting fluids for their specific applications and provide valuable input for computational models simulating the influence of MWFs in the primary and secondary shear zones between cutting tools and the workpiece/chiplet. Full article

Graphene films are widely used in thermal management of electronic devices due to their excellent properties such as high flexibility, high thermal conductivity and light weight. However, in the traditional preparation process, some structural defects are introduced, which will lead to an increase in phonon scattering, thereby reducing the thermal conductivity of graphene. Therefore, a new method for preparing graphene thin films is proposed by using the evaporation method; the graphene oxide composite film is prepared by adding carbon-rich molecules (CRMs) to the graphene oxide dispersion liquid. The experimental results show that the addition of a mass fraction of 0.15% CRMs helps to form continuous strips and channels, which are beneficial to the construction of the internal aromatic structure of graphene and improve the crystallinity of graphene film. The in-plane thermal conductivity of the composite film increased from 598.74 W/(m·K) to 704.27 W/(m·K) after adding carbon-rich molecules. However, excess CRMs can lead to the formation of disordered structures during graphitization, which will reduce the thermal conductivity of the film to a certain extent. The radiation properties of graphene films are also proposed to verify the validity of the above conclusions, and the results show that the graphene film with a mass fraction of 0.24% CRMs has better heat dissipation performance, which can be reduced by 5 °C compared with that of pure graphene film. Through the application of graphene in new energy car seats, it is proved that compared with the resistance wire seats, graphene seats have better performance in terms of a fast heating speed and uniform heating. Full article

A linear stability analysis is performed for a power-law liquid film flowing down an inclined rigid plane over a deformable solid layer. The deformable solid is modeled using a neo-Hookean constitutive equation, characterized by a constant shear modulus and a nonzero first normal stress difference in the base state at the fluid–solid interface. To solve the linearized eigenvalue problem, the Riccati transformation method, which offers advantages over traditional techniques by avoiding the parasitic growth seen in the shooting method and eliminating the need for large-scale matrix eigenvalue computations, was used. This method enhances both analytical clarity and computational efficiency. Results show that increasing solid deformability destabilizes the flow at low Reynolds numbers by promoting short-wave modes, while its effect becomes negligible at high Reynolds numbers where inertia dominates. The fluid’s rheology also plays a key role: at low Reynolds numbers, shear-thinning fluids ($n<1$) are more prone to instability, whereas at high Reynolds numbers, shear-thickening fluids ($n>1$) exhibit a broader unstable regime. Full article

Coordination polymers are attractive materials for various fields of practical application. The high degree of freedom of choice of metal ions and organic ligands plays a critical role in functional diversification. In the present study, we report the liquid–liquid interfacial synthesis of a 2D bis(terpyridine)copper(II) polymer thin film, Cu-tpy. The synthesized Cu-tpy was characterized by various microscopic observations such as TEM, SEM, and AFM, and spectroscopic measurements such as XPS, Raman spectroscopy, SEM/EDS, and UV–Vis spectroscopy. Synchrotron-radiated X-ray scattering confirmed that Cu-tpy was oriented crystalline films. Moreover, Cu-tpy showed electrochemical micro-supercapacitor behavior in the solid-state owing to its ionic nature. This study expands the potential of bis(terpyridine)metal(II) polymers as electro-functional materials. Full article