Search Results (1,637)

Surfactants are widely utilized in agriculture as emulsifying, dispersing, anti-foaming, and wetting agents. In these adjuvant roles, the inherent biological activity of the surfactant is secondary to the active ingredients. Here, the hydrophilic non-ionic surface-active tri-block copolymer Pluronic^® F68 is investigated for direct biological activity in wheat. F68 binds to and inserts into lipid membranes, which may benefit crops under abiotic stress. F68’s interactions with Triticum aestivum (var Juniper) seedlings and a seed-borne Bacillus spp. endophyte are presented. At concentrations below 10 g/L, F68-primed wheat seeds exhibited unchanged emergence. Root-applied fluorescein-F68 (fF68) was internalized in root epidermal cells and concentrated in highly mobile endosomes. The potential benefit of F68 in droughted wheat was examined and contrasted with wheat treated with the osmolyte, glycine betaine (GB). Photosystem II activity of droughted plants dropped significantly below non-droughted controls, and no clear benefit of F68 (or GB) during drought or rehydration was observed. However, F68-treated wheat exhibited increased transpiration values (for watered plants only) and enhanced shoot dry mass (for watered and droughted plants), not observed for GB-treated or untreated plants. The release of seed-borne bacterial endophytes into the spermosphere of germinating seeds was not affected by F68 (for F68-primed seeds as well as F68 applied to roots), and the planktonic growth of a purified Bacillus spp. seed endophyte was not reduced by F68 applied below the critical micelle concentration. These studies demonstrated that F68 entered wheat root cells, concentrated in endosomes involved in transport, significantly promoted shoot growth, and showed no adverse effects to plant-associated bacteria. Full article

Surfactants can be utilized to improve oil recovery by changing the performance of reservoirs in rock pores. Kerogen is the primary organic matter in shale; however, high temperatures will affect the overall performance of this surfactant, resulting in a decrease in its activity or even failure. The effect of surfactants on kerogen pyrolysis has rarely been researched. Therefore, this study synthesized a polymeric surfactant (PS) with high temperature resistance and investigated its effect on kerogen pyrolysis under the friction of drill bits or pipes via molecular dynamics. The infrared spectra and thermogravimetric and molecular weight curves of the PS were researched, along with its surface tension, contact angle, and oil saturation measurements. The results showed that PS had a low molecular weight, with an MW value of 124,634, and good thermal stability, with a main degradation temperature of more than 300 °C. It could drop the surface tension of water to less than 25 mN·m⁻¹ at 25–150 °C, and the use of slats enhanced its surface activity. The PS also changed the contact angles from 127.96° to 57.59° on the surface of shale cores and reversed to a water-wet state. Additionally, PS reduced the saturated oil content of the shale core by half and promoted oil desorption, indicating a good cleaning effect on the shale oil reservoir. The kerogen molecules gradually broke down into smaller molecules and produced the final products, including methane and shale oil. The main reaction area in the system was the interface between kerogen and the surfactant, and the small molecules produced on the interface diffused to both ends. The kinetics of the reaction were controlled by two processes, namely, the step-by-step cleavage process of macromolecules and the side chain cleavage to produce smaller molecules in advance. PS could not only desorb oil in the core but also promote the pyrolysis of kerogen, suggesting that it has good potential for application in shale oil exploration and development. Full article

Due to the complex mineral composition, low clay content, and strong heterogeneity of the mixed sedimentary shale in the Xinjiang Salt Lake Basin, the wettability characteristics of the reservoir and their influencing factors are not yet clear, which restricts the evaluation of oil-bearing properties and the identification of sweet spots. This paper analyzed mixed sedimentary shale samples from the Lucaogou Formation of the Jimsar Sag and the Fengcheng Formation of the Mahu Sag. Methods such as petrographic thin sections, X-ray diffraction, organic matter content analysis, and argon ion polishing scanning electron microscopy were used to examine the lithological and mineralogical characteristics, geochemical characteristics, and pore space characteristics of the mixed sedimentary shale reservoir. Alternating imbibition and nuclear magnetic resonance were employed to quantitatively characterize the wettability of the reservoir and to discuss the effects of compositional factors, lamina types, and pore structure on wettability. Research findings indicate that the total porosity, measured by the alternate imbibition method, reached 72% of the core porosity volume, confirming the effectiveness of alternate imbibition in filling open pores. The Lucaogou Formation exhibits moderate to strong oil-wet wettability, with oil-wet pores predominating and well-developed storage spaces; the Fengcheng Formation has a wide range of wettability, with a higher proportion of mixed-wet pores, strong heterogeneity, and weaker oil-wet properties compared to the Lucaogou Formation. TOC content has a two-segment relationship with wettability, where oil-wet properties increase with TOC content at low TOC levels, while at high TOC levels, the influence of minerals such as carbonates dominates; carbonate content shows an “L” type response to wettability, enhancing oil-wet properties at low levels (<20%), but reducing it due to the continuous weakening effect of minerals when excessive. Lamina types in the Fengcheng Formation significantly affect wettability differentiation, with carbonate-shale laminae dominating oil pores, siliceous laminae contributing to water pores, and carbonate–feldspathic laminae forming mixed pores; the Lucaogou Formation lacks significant laminae, and wettability is controlled by the synergistic effects of minerals, organic matter, and pore structure. Increased porosity strengthens oil-wet properties, with micropores promoting oil adsorption through their high specific surface area, while macropores dominate in terms of storage capacity. Wettability is the result of the synergistic effects of multiple factors, including TOC, minerals, lamina types, and pore structure. Based on the characteristic that oil-wet pores account for up to 74% in shale reservoirs (mixed-wet 12%, water-wet 14%), a wettability-targeted regulation strategy is implemented during actual shale development. Surfactants are used to modify oil-wet pores, while the natural state of water-wet and mixed-wet pores is maintained to avoid interference and preserve spontaneous imbibition advantages. The soaking period is thus compressed from 30 days to 3–5 days, thereby enhancing matrix displacement efficiency. Full article

This study presents the synthesis, characterization, and application of magnetic magnetite–zirconium dioxide (Fe₃O₄–ZrO₂) nanoparticles as an efficient nanoadsorbent for fluoride removal from water. The nanoparticles were synthesized using a wet chemical co-precipitation method with Fe/Zr molar ratios of 1:1, 1:2, and 1:4, and characterized using Fourier-transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy (EDS). FTIR analysis confirmed the presence of Fe₃O₄ and ZrO₂ functional groups, while XRD showed that increased Zr content led to a dominant amorphous phase. SEM and EDS analyses revealed quasi-spherical and elongated morphologies with uniform elemental distribution, maintaining the designed Fe/Zr ratios. Preliminary adsorption tests identified the Fe/Zr = 1:1 (M1) nanoadsorbent as the most effective due to its high surface homogeneity and optimal fluoride-binding characteristics. Adsorption experiments demonstrated that the material achieved a maximum fluoride adsorption capacity of 70.4 mg/g at pH 3, with the adsorption process best fitting the Temkin isotherm model (R² = 0.987), suggesting strong adsorbate–adsorbent interactions. pH-dependent studies confirmed that adsorption efficiency decreased at higher pH values due to electrostatic repulsion and competition with hydroxyl ions. Competitive ion experiments revealed that common anions such as nitrate, chloride, and sulfate had negligible effects on fluoride adsorption, whereas bicarbonate, carbonate, and phosphate reduced removal efficiency due to their strong interactions with active adsorption sites. The Fe₃O₄–ZrO₂ nanoadsorbent exhibited excellent magnetic properties, facilitating rapid and efficient separation using an external magnetic field, making it a promising candidate for practical water treatment applications. Full article

This study investigates the effect of accelerated aging on the microstructure and surface properties of synthetic sports surfaces, with the goal of developing a more representative laboratory simulation method. Three common types of polyurethane-based sports surfaces were examined: (1) a dual-layer SBR base with a thin EPDM spray topcoat; (2) a single-layer EPDM surface with a smooth finish; and (3) a dual-layer “sandwich” structure with a rough EPDM upper layer. Samples were tested for slip resistance (PTV), abrasion resistance, and surface morphology using SEM, as well as surface roughness and tensile properties before and after aging. Method combining UV radiation and water spray was introduced and evaluated. Microstructural analysis with roughness measurements revealed surface degradation in all materials, with more extensive damage observed in the UV + spray cycle. Slip resistance results showed reduced performance in dry conditions and improved values in wet conditions post-aging. The single-layer EPDM surface demonstrated the highest initial dry PTV, while the dual-layer with spray had the lowest. After aging, all surfaces exhibited smaller differences between dry and wet performance but no longer met dry condition standards. These results may guide future revisions of performance testing standards and contribute to the development of safer, longer-lasting synthetic sports surfaces. Full article

This research addresses urban heat island intensification driven by urbanization using Dianchi Lake in Kunming, China, as a case study, aiming to quantitatively evaluate the spatial extent, intensity, and land cover sensitivity differences in the cooling effects of large urban water bodies across dry/wet seasons and complex urban landscapes (forest, cropland, and impervious surfaces) to provide a scientific basis for optimizing thermal environments in low-latitude plateau cities. Based on Landsat 8/9 satellite data from dry (January) and wet (May) seasons in 2020 and 2023 used for land surface temperature (LST) retrieval combined with land use data, buffer zone gradient analysis was adopted to quantify the spatial heterogeneity of key cooling indicators within 0–1500 m lakeshore buffers. The results demonstrated significant seasonal differences. The wet season showed a greater cooling extent (600 m) and higher intensity (6.0–6.6 °C) compared with the dry season (400 m; 2.4–3.9 °C). The land cover responses varied substantially, with cropland having the largest influence (600 m), followed by impervious surfaces (400 m), while forest exhibited a minimal effective cooling range (100 m) but localized warming anomalies at 200–400 m. Sensitivity analysis confirmed that impervious surfaces were the most sensitive to water-cooling, followed by cropland, whereas forest showed the lowest sensitivity. Full article

The Subsurface self-regulating, Low-Energy, Clay-based Irrigation (SLECI) system is a recently developed irrigation method. The SLECI system supplies water directly to the crop root zone by utilising the potential difference established between its permeable interior and exterior radial walls. In this study, we investigated the effect of the SLECI emitter’s operating pressure head and burial depth on the water flow characteristics in sandy loam soil. The results show that the developed COMSOL-2D model accurately predicted water flow characteristic under SLECI. The operating pressure head significantly influenced the water flow characteristics. As the operating pressure head increased, emitter discharge increased, and the wetted soil area was extended. The burial depth had a minimal effect on the emitter discharge but notably affected the advancement and time at which wetting fronts reached the soil surface and bottom boundaries. Operating the SLECI emitter at a higher operating pressure head and shallower burial depth could degrade irrigation water application and water use efficiencies. Based on a multi-objective optimisation algorithm, we recommend that the SLECI emitter be operated at a 125 cm pressure head and buried at 40 cm for crops with a root zone depth of 100 cm. Our study is expected to provide a greater understanding of the SLECI system and offer some recommendations and guidelines for its efficient deployment in sandy loam for enhanced water use efficiency in crop production. Full article

It is imperative to investigate the behavior of the droplet superimposed condensation of deltamethrin reagent on strawberry leaf surface, as well as the dynamic variation rule of its contact angle. A microinjector was utilized to conduct the experiment of droplet superposition and condensation. The surface tension of deltamethrin droplets was measured by means of an optical contact angle meter, and the wetting parameters, such as contact angle, volume, and spreading diameter, were obtained by observing the leaf surfaces of various parts of strawberries during the dynamic process of superimposed condensation. A model was constructed by establishing the relationship between the contact angle and the coordinates of the observation point and time through the spatial fitting interpolation method. This model is a three-dimensional dynamic trend surface model of contact angle for droplet superposition and condensation. The findings indicated that the surface tension of the deltamethrin drop was 28.92 ± 0.2 mN·m⁻¹. The interval between the superposition of two droplets and the subsequent condensation of a new droplet was found to be within 0.5 s. The time taken for a new droplet to form was found to be between 0.0356 and 0.0476 s. The change in contact angle during the processes of superposition and coalescence can be broadly categorized into three distinct stages: namely, sharp oscillation, slight decrease, and gentle stabilization. The volume of the new droplet formed by the superposition and condensation was found to be 1.05 to 1.93 times that of a lying droplet. The maximum increase in the spreading diameter of the superimposed and condensed droplets was 40.29%. The three-dimensional dynamic trend surface model can reflect the overall spatial–temporal change trend of the contact angle in the process of superposition and coalescence. The model successfully passed the overall significance F-test and each coefficient of the statistical t-test, and demonstrated a satisfactory time interpolation effect. The experimental verification demonstrates that the predicted contact angle value of the model is consistent with the measured value. Full article

The ecological environment of Inner Mongolia constitutes a critical component of China’s ecological civilization construction. To comprehensively assess and monitor ecological quality dynamics in this region, this study employed MODIS remote sensing data products (2000–2020) and derived four key indicators, —vegetation index (NDVI), wetness index (WET), build-up and soil index (NDBSI), and land surface temperature (LST)—via the Google Earth Engine (GEE) platform. A Remote Sensing-based Ecological Index (RSEI) was constructed using principal component analysis (PCA) to establish an annual long-term time series, thereby eliminating subjective bias from artificial weight assignment. Integrated methodologies—including Theil–Sen Median and Mann–Kendall trend analysis, Hurst exponent, and geographical detector—were applied to investigate the spatiotemporal evolution of ecological quality in Inner Mongolia and its responses to climatic and anthropogenic drivers. This study proposes a novel framework for large-scale ecological quality assessment using remote sensing. Key findings include the following: The mean RSEI value of 0.41 (2000–2020) indicates an overall improving trend in ecological quality. Areas with ecological improvement and degradation accounted for 76.06% and 23.84% of the region, respectively, exhibiting a spatial pattern of “northwestern improvement versus southeastern degradation.” Pronounced regional disparities were observed: optimal ecological conditions prevailed in the Greater Khingan Range (northeast), while the Alxa League (southwest) exhibited the poorest conditions. Northwestern improvement was primarily driven by increased precipitation, rising temperatures, and conservation policies, whereas southeastern degradation correlated with rapid urbanization and intensified socioeconomic activities. Our results demonstrate that MODIS-derived RSEI effectively enables large-scale ecological monitoring, providing a scientific basis for regional green development strategies. Full article

This work investigated the effect of experimental conditions of dry and wet torrefaction on the properties of olive leaves and olive pomace. Torrefaction improved the fuel properties of olive waste. According to Van Krevelen parameters (O/C and H/C ratios), torrefied biomass, tested as solid biofuel, achieved a similar quality threshold to lignite. For example, dry torrefaction conducted at 230 °C for 80 min reduced the O/C and H/C ratios of olive leaves from 0.51 and 1.51 for raw biomass to 0.25 and 1.17 for torrefied biomass, respectively. Under the same conditions, the O/C and H/C ratios of olive pomace were also reduced from 0.34 and 1.60 to 0.27 and 1.36, respectively. Calorific values of raw olive leaves and olive pomace amounted to 18.0 and 23.2 MJ/kg, respectively. Following dry torrefaction and biomass conversion into biochar, calorific values of olive leaves and olive pomace increased by 24% and 14% up to 22.2 and 26.3 MJ/kg through dry torrefaction, compared with 17% and 23% increments up to 21.1 and 28.5 MJ/kg through wet torrefaction, respectively. Interestingly, biomass processing through wet torrefaction performed in a fluidized bed powered by superheated steam could be completed 8- to 12-fold more rapidly than dry torrefaction. SEM analysis indicated a breakdown of the surface structure of olive waste following the torrefaction process. According to the Brunauer–Emmett–Teller (BET) method, total pore surface areas of biochar obtained from wet torrefaction of olive pomace and olive leaves amounted to 3.6 m²/g and 0.8 m²/g, with total pore volumes amounting to 0.0225 cm³/g and 0.0103 cm³/g, respectively. Maximal contents of 5-hydroxymethylfurfural and furfural in liquid by-products from dry torrefaction amounted to 1930 and 1880 mg/1 kg, respectively. Alternately, in liquid by-products from wet torrefaction, concentrations of these high-value compounds remained very low. Full article

This work concerns the preparation of Pt/AC catalysts (Pt supported on activated carbon) and their application to the synthesis of hydrocarbon biofuels through the HEFA (hydroprocessing of esters and fatty acids) route. The key motivation for the work was that catalysts based on sulfided Mo supported on γ-Al₂O₃, traditionally employed in the hydroprocessing of petroleum derivatives, (i) are unstable in the HDO (hydrodeoxygenation) of biomass-derived feedstocks and (ii) can contaminate the resulting biofuels with sulfur. In this context, a systematic study on the effects of preparation conditions on the properties of the resulting Pt/AC catalysts and their performance in HEFA was carried out for the first time. Efficient catalysts were obtained, which led to the complete deoxygenation of lauric acid and coconut oil, yielding products composed primarily of n-alkanes. The highest HDO activity was verified for the catalyst prepared using as a support an AC previously subjected to thermal treatment up to 800 °C in a H₂ atmosphere (which removed most of the surface acidic oxygenated groups), depositing Pt over the surface of this support via wet impregnation using a H₂PtCl₆ solution acidified with HCl. The obtained results showed the great potential of the Pt/AC catalysts for the production of hydrocarbon biofuels through the HEFA route. Full article

Electret filter media are electrostatically charged during the manufacturing process to activate effective electrical separation mechanisms. In order to investigate the influence of humidity on these mechanisms, the electric field, and filtration efficiency, a Direct Numerical Simulation (DNS) study of the aerosol deposition within wetted fibrous nonwoven filter media used in masks was carried out. Initial experimental investigations determined key properties of the filter material, including porosity, fiber diameter, and surface charge density. Using Micro-Computed Tomography (µCT), preferred locations for droplet deposition within the filter were identified. Additional experiments quantified the amount of water absorbed by the filter medium and assessed its impact on the existing electric field. Numerical simulations examined various models with differing porosity and fiber diameter, incorporating different levels of water content to analyze the changes in the electric field, flow velocity, and resulting filtration efficiency. The results provide valuable insights into the significant effects of fiber change on filtration performance, demonstrating the electret filter’s ability to partially compensate for the negative impacts of water. Full article

This study presents a one-dimensional solver of the shallow water equations designed for the wet-bed step Riemann problem. Nonlinear mass and momentum equations incorporating shock and rarefaction waves in a straight one-dimensional channel are expressed as a pair of equations that depend solely on local depth values either side of the step. These unified equations are uniquely designed for the four conditions involving shock and rarefaction waves that can occur in the Step Riemann Problem. The Levenberg–Marquardt method is used to solve these simplified nonlinear equations. Four verification tests are considered for shallow free surface flow in a wet-bed channel with a step. These cases involve two rarefactions, opposing shock-like hydraulic bores, and a rarefaction and shock-like bore. The numerical predictions are in close agreement with existing theory, demonstrating that the method is very effective at solving the wet-bed step Riemann problem. Full article

Global climate change has led to a marked increase in the frequency of record-breaking extreme rainfall events, which often surpass historical benchmarks and pose significant challenges to conventional geological hazard risk assessment methods. This study used a record-breaking extreme rainfall event in Zhenba County, Shaanxi Province, in July 2023 as a case study to develop a tailored risk assessment framework for geological hazards under extreme rainfall conditions. By integrating high-resolution Planet satellite imagery, millimeter-scale surface deformation data derived from SBAS-InSAR, and detailed field investigation results, a comprehensive disaster inventory containing 1012 landslides was compiled. The proposed framework integrates cumulative extreme rainfall metrics with subtle ground deformation indicators and applies four advanced machine learning algorithms—DNN, XGBoost, RF, and LightGBM—for multidimensional hazard assessment. Among these, the DNN model exhibited the highest performance, achieving an AUC of 0.82 and Kappa coefficients of 0.833 (training) and 0.812 (prediction). Further analysis using SHAP values identified distance to rivers, cumulative rainfall, and the Topographic Wetness Index (TWI) as the most influential factors governing landslide occurrence under extreme rainfall conditions. Validation using representative case studies confirmed that the framework effectively identifies high-hazard zones, particularly in areas severely impacted by debris flows and landslide deformation zones. These findings provide a robust scientific foundation and technical basis for early warning, disaster prevention, and mitigation strategies in geologically complex regions increasingly affected by extreme rainfall events. Full article

Climate variations impact the preservation of heritage buildings, necessitating a strategic understanding of potential effects to effectively guide preservation efforts. This study analyzes temperature- and precipitation-dependent climate-heritage indices in Trentino–South Tyrol using EURO-CORDEX regional climate models for the period 1971–2100 under RCP 4.5 and RCP 8.5 scenarios. The selected indices were calculated with climdex-kit and relied on bias-adjusted temperature and precipitation data with a 1 km spatial resolution. The obtained results indicate a geographically punctuated increase in biomass accumulation on horizontal surfaces, a slight decreasing trend in freeze–thaw events, an increase in growing degree days indicating a small, heightened insect activity, and a rise in heavy precipitation days. The Scheffer Index shows a significantly increased potential for wood degradation, particularly under the RCP 8.5 scenario, while the Wet-Frost Index remains consistently low. Finally, according to each identified hazard, adaptive solutions are suggested. These findings provide critical insights into future climate impacts on heritage buildings in the region, aiding stakeholders in planning targeted interventions. The study emphasizes the crucial role of integrating detailed climate data into heritage preservation strategies, advocating for the inclusion of future risk analysis in the “knowledge path” in order to enhance the resilience of buildings. Full article