Search Results (366)

This article investigates how to exploit the high-frequency mmWave for 5G-advanced and beyond, which requires new filters for the wide bandpass and its multi-sub-band. Based on the substrate-integrated waveguide (SIW), spoof surface plasmon polariton (SSPP), and metastructures, like complementary split-ring resonators (CSRRs), the development of a wide bandpass filter and a multi-sub-band filter is proposed, along with an experimental realization to verify the model. The upper and lower cutoff frequencies of the wide bandpass are controlled through an SIW-SSPP structure, whereas the corresponding wide bandpass and its multi-sub-band filters are designed through incorporating new metastructures. The frequency range of 24.25–29.5 GHz, which covers the n257, n258, and n261 bands for 5G applications, was selected for verification. The basic SIW-SSPP wide bandpass structure of 24.25–29.5 GHz was designed first. Then, by incorporating an Archimedean spiral configuration, the insertion loss within the passband was reduced from 1 dB to 0.5 dB, while the insertion loss in the high-frequency stopband was enhanced from 40 dB to 70 dB. Finally, CSRRs were integrated to effectively suppress undesired frequency components within the bandpass, thereby achieving multi-sub-band filters with low insertion losses with a triple-sub-band filter of 0.5 dB, 0.7 dB, and 0.8 dB in turn. The experimental results showed strong agreement with the design scheme, thereby confirming the rationality of the design. Full article

Aircraft, as electromagnetically complex targets, have radar cross-sections (RCSs) that are influenced by various factors, with the inlet duct being a critical component that often serves as a primary source of electromagnetic scattering, significantly impacting the scattering characteristics. In light of the conflict between aerodynamic performance and electromagnetic characteristics in the design of aircraft engine inlet grilles, this paper proposes a metasurface radar-absorbing inlet grille (RIG) solution based on a NACA symmetric airfoil. The RIG adopts a sandwich structure consisting of a polyethylene terephthalate (PET) dielectric substrate, a copper zigzag metal strip array, and an indium tin oxide (ITO) resistive film. By leveraging the principles of surface plasmon polaritons, electromagnetic wave absorption can be achieved. To enhance the design efficiency, a multi-objective Bayesian optimization framework driven by the expected hypervolume improvement (EHVI) is constructed. The results show that, compared with a conventional rectangular cross-section grille, an airfoil-shaped grille under the same constraints will reduce both aerodynamic losses and the absorption bandwidth. After 100-step EHVI–Bayesian optimization, the optimized balanced model attains a 57.79% reduction in aerodynamic loss relative to the rectangular-shaped grille, while its absorption bandwidth increases by 111.99%. The RCS exhibits a reduction of over 8.77 dBsm in the high-frequency band. These results confirm that the proposed optimization design process can effectively balance the conflict between aerodynamic performance and stealth performance for RIGs, reducing the signal strength of aircraft engine inlets. Full article

This paper focuses on the switching and modulation techniques of terahertz waves, develops ${\mathrm{VO}}_2$ thin-film materials with an SPP structure, and uses terahertz time-domain spectroscopy (THz-TDS) to study the semiconductor–metal phase transition characteristics of ${\mathrm{VO}}_2$ thin films, especially the photoinduced semiconductor–metal phase transition characteristics of silicon-based ${\mathrm{VO}}_2$ thin films. The optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films to terahertz waves under different light excitation modes, such as continuous light irradiation at different wavelengths and femtosecond pulsed laser irradiation, were analyzed. Combining the optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films with the filtering characteristics of SPP structures, composite structures of ${\mathrm{VO}}_2$ thin films with metal hole arrays, composite structures of ${\mathrm{VO}}_2$ thin films with metal block arrays, and silicon-based ${\mathrm{VO}}_2$ microstructure arrays were designed. The characteristics of this dual-function device were tested experimentally. The experiment proves that the ${\mathrm{VO}}_2$ film material with an SPP structure has a transmission rate dropping sharply from 32% to 1% under light excitation; the resistivity changes by more than six orders of magnitude, and the modulation effect is remarkable. By applying the SPP structure to the ${\mathrm{VO}}_2$ material, the material can simultaneously possess modulation and filtering functions, enhancing its optical performance in the terahertz band. Full article

Magneto-plasmonic structures have been a subject of tremendous attention of researchers in recent decades as they provide unique approaches regarding the efficient control of optical, magneto-optical, and nonlinear-optical effects. Among others, magneto-plasmonic crystals (MPCs) have become one of the most studied structures, known for their high-quality tunable resonant optical properties. Here, we present the results of experimental and numerical studies on the functional magneto-optical (MO) response of planar 1D plasmonic crystals composed of Co/Au stripes of submicron period on the surface of a 3 μm thick rare-earth garnet layer. The experimental and numerical studies confirm that the wavelength–angular spectra of such structures contain a set of tunable resonant features in their optical and magneto-optical response, associated with the excitation of (i) surface plasmon polaritons at the Co/Au grating–garnet interface, as well as (ii) waveguide (WG) modes propagating in the garnet slab. A comparison of the MO effects in the transversal and longitudinal magnetization of the plasmonic structures is presented. We show that the most efficient Fano-type MPC magneto-optical response is realized for the WG modes of the first order for the longitudinal magnetization of the structure. Further perspectives regarding the optimization of this type of plasmonic crystal are discussed. Full article

This paper investigates a graphene-on-insulator power divider designed for terahertz applications based on spoof surface plasmon polaritons. We optimize structural parameters to maximize signal transmission from input to output ports while achieving a uniform and symmetrical electric field distribution at the output cross-section. Our findings indicate that utilizing three graphene layers significantly enhances power distribution and symmetry at output ports. We demonstrate electrical control over waveguide transmission properties by modulating the graphene chemical potential from 0 to 0.5 eV. The proposed device holds promise for applications in plasmonic circuits and on-chip interconnects operating within the terahertz frequency range. Full article

In this paper, we experimentally investigated the excitation of spoof surface plasmon polaritons (SSPPs) supported by a 1D subwavelength grating with a rectangular profile in the terahertz (THz) frequency range. Using the attenuated total reflection technique and the THz radiation of the Novosibirsk free electron laser, we carried out detailed studies of both angular and gap spectra at several wavelengths. A shallow grating supporting a fundamental mode was fabricated by means of multibeam X-ray lithography and used as a test sample. The results indicated that we achieved 1-THz tunability of resonance in the frequency range from 1.51 to 2.54 THz on a single grating, which cannot be obtained with active tunable metamaterials. The Q factors of the resonances in the angular spectra were within the range of 19.4–37.6, while the resonances of the gap spectra had a Q factor lying within the 1.17–2.03 range. The gap adjustment capability of the setup shown in the work has great potential in modulation of the absorption efficiency, whereas the angular tuning and recording data from each point of the grating will enable real-time monitoring of changes in the surrounding medium. All of this is highly important for enhanced terahertz real-time absorption spectroscopy and imaging. Full article

Conventional all-optical modulators based on surface plasmon polaritons (SPPs) primarily utilize the nonlinear effect of a given material for modulation. Their performance is heavily dependent on the optical properties of the dielectric materials used and requires high pumping power. However, manipulating SPPs by controlling electron concentrations offers a material-independent approach suitable for all-optical modulators. In this paper, we propose a hybrid gold–ITO–silver block structure integrated within a Mach–Zehnder interferometer configuration to address this problem. The gold–ITO interface effectively localizes propagating SPPs. The pump light excites localized surface plasmons (LSPs) in the silver block, generating surface electric fields that modulate the electron concentration in the adjacent ITO layer. The extinction ratio is 50.8 dB when the electron concentration changes by 3.3 × 10²⁰ cm⁻³, indicating that this structure is an all-optical modulator with a high extinction ratio. This approach shows significant promise for reducing pump power and enhancing the performance of all-optical modulators. Full article

Near-field imaging of the hybrid surface plasmon-phonon polaritons on the n-GaN semiconductor was performed using a scattering scanning near-field optical microscope at the selected frequencies of 920 cm⁻¹ and 570 cm⁻¹. The experimental measurements and numerical modeling data were in good agreement, revealing the large propagation distances on the n-GaN semiconductor and other insights which could be obtained by analyzing the dispersion characteristics of hybrid polaritons. In particular, the decay lengths of polaritons at the excitation frequency of 920 cm⁻¹ were measured to be up to 25 and 30 µm in experiment and theory, respectively. In the case of excitation at the frequency of 570 cm⁻¹, the surface plasmon-phonon polaritons’ decay distances were 25 µm and 105 µm, respectively, noting the limitations of the near-field optical microscope setups used. Dispersion characteristics of the resonant frequency and the damping rate of hybrid polaritons were numerically modeled and compared with the analytical calculations, validating the need for further experiment improvements. The launch conditions for the near-field observation of extraordinary coherence of the surface plasmon-phonon polaritons were also discussed. Full article

This study investigates the change in both the angular position and width of the reflectance minimum of an SPR sensor in the Kretschmann configuration when optical vortices instead of plane waves are used for illumination. An analytical expression of the reflectance is obtained for incident Laguerre–Gaussian beams, considering only the first-order approximation of the Fresnel reflection coefficient in a Taylor series. Numerical simulations reveal that the detection performance of SPR sensors is practically unaffected if optical vortices of this type are used as sources, even if the topological charges of the vortices are quite large. On the other hand, the use of optical vortices in SPR sensors could be very advantageous for positioning and manipulating analyte molecules on the surface of the sensor. Full article

Perovskite, as a promising class of photodetection material, demonstrates considerable potential in replacing conventional bulk light-detection materials such as silicon, III–V, or II–VI compound semiconductors and has been widely applied in various special light detection. Relying solely on the intrinsic photoelectric properties of perovskite gradually fails to meet the evolving requirements attributed to the escalating demand for low-cost, lightweight, flexible, and highly integrated photodetection. Direct manipulation of electrons and photons with differentiation of local electronic field through predesigned optical nanostructures is a promising strategy to reinforce the detectivity. This review provides a concise overview of the optical manipulation strategy in perovskite photodetector through various optical nanostructures, such as isolated metallic nanoparticles and continuous metallic gratings. Furthermore, the special light detection techniques involving more intricate nanostructure designs have been summarized and discussed. Reviewing these optical manipulation strategies could be beneficial to the next design of perovskite photodetector with high performance and special light recognition. Full article

Non-radiative decay of surface plasmon (SP) offers a novel paradigm for efficient conversion of photons into carriers. However, the narrow bandwidth of SP has been a significant obstacle to the widespread applications. Previously, research and applications mainly focused on noble metals such as Au, Ag, and Cu. In this article, we report an Ag-Al alloy material, μ-Ag₃Al, in which the surface plasmon operating bandwidth is 1.7 times that of Ag and hot carrier transport properties are comparable with those of AuAl. The results show that μ-Ag₃Al allows efficient direct interband electronic transitions from ultraviolet (UV) to near infrared range. Spherical nanoparticles of μ-Ag₃Al exhibit the localized surface plasmon resonance (LSPR) effect in the ultraviolet region. Its surface plasmon polariton (SPP) shows strong non-radiative decay at 3.36 eV, which is favorable for the generation of high-energy hot carriers. In addition, the penetration depth of SPP in μ-Ag₃Al remains high across the UV to the near-infrared range. Moreover, the transport properties of hot carriers in μ-Ag₃Al are comparable with those in Al, borophene and Au-Al intermetallic compounds. These properties can provide guidance for the design of plasmon-based photodetectors, solar cells, and photocatalytic reactors. Full article

A real-time tunable planar plasmonic waveguide based on a voltage-adjustable ferroelectric resonator is designed and investigated. The laminated ferroelectric compound resonator is composed of a ferroelectric Ba_0.85Ca_0.15Zr_0.9Ti_0.1O₃ (BCZT) layer, a PCB layer, as well as a localized spoof plasmonic metal layer, where the BCZT layer is beneficial for enhancing the voltage tunability in the spoof surface plasmon polariton (SSPP) waveguide. The simulated results show that the tuning range of the notch in the transmission curve, generated by the coupling between the ferroelectric compound resonator and the plasmonic waveguide, can achieve a variation of up to 8.8% thanks to the large tunability value in the BCZT ferroelectric layer. In addition, the notches consist of Fano resonant frequencies, the generation mechanism of which is elaborately discussed in terms of the temporal coupled mode theory. Full article

Due to their high breakdown threshold and acceleration gradient, dielectric laser accelerators (DLAs) have become an important technical direction of accelerator miniaturization. In this study, an electron accelerator scheme based on graphene surface plasmon polaritons (SPPs) is proposed. The grating was designed to be etched on the silica surface in the simulation, and a layer of graphene was modeled to cover the surface of the medium. The incident laser light in the simulation was configured to be coupled by the grating to generate surface plasmon polaritons (SPPs) on the graphene surface. According to the simulation results, a relatively large acceleration channel aperture and long acceleration length could be formed on the graphene surface using a mid-infrared laser; this provides a technical solution for increasing the beam current of a DLA. A 53.375 THz laser was incident on the surface of the accelerating structure to carry out tracking calculations on a 10 MeV electron beam. For the 100 $\mu$m accelerating structure, an energy gain of 0.105 MeV was achieved, and the acceleration gradient reached 1.05 GeV/m. Full article

Directional coupling of light at the nanoscale plays a significant role in both fundamental research and practical applications, which are crucial for the development of on-chip photonic devices. In this work, we propose a broadband directional coupler for surface plasmon polaritons (SPPs) utilizing a pair of obliquely perforated nanoslits. We demonstrate that tilting the slits significantly enhances the sensitivity of plasmonic coupling phase variation to the wavelength of the incident light, enabling precise wavelength-dependent control over SPP propagation. By optimizing the width and tilting angle of each nanoslit, we achieve an extinction ratio exceeding 10 dB with a bandwidth exceeding 400 nm and a maximum unidirectional transmission of up to 30 dB. This broadband directional SPP coupler presents a promising platform for the design and fabrication of integrated plasmonic circuits and high-performance optical devices and sensors. Full article

Microporous metal materials have promising applications in the high-temperature industry for their high heat exchange efficiency. However, due to their complex internal structure, analyzing the heat transfer mechanisms presents a great challenge. This I confirm work introduces a mathematical model to accurately calculate the radiative thermal conductivity of microporous open-cell metal materials. The finite element and lattice Boltzmann methods were employed to calculate the thermal conduction and thermal radiation conductivities separately and validated for aluminum foams, with the relative errors all less than 9.3%. The results show that the thermal conductivity of microporous metal materials mainly increased with an increase in temperature and volume-specific surface area but decreased with an increase in porosity. Analysis of the spectral radiation characteristics shows that the surface plasmon polariton resonance and the magnetic polariton resonance appearing at the gas–solid interface of the metal foam significantly increase the dissipation effect of the gas–solid interface, further reducing the metal foam’s heat transfer efficiency. This indicates the potential of this work for use in the design of specific microporous metal materials like energy management devices or heat transfer exchangers in the aerospace industry. Full article