Search Results (192)

Building-integrated photovoltaic (BIPV) windows present a viable path towards carbon neutrality in the building sector. However, conventional BIPV windows, such as semi-transparent photovoltaic (STPV) glazings, still suffer from inadequate thermal insulation, which limits their effectiveness across different climate conditions. To address this issue, the cadmium telluride-based vacuum PV glazing has been developed to enhance the thermal performance of BIPV applications. To fully understand the complex thermal behaviour under real-world operational scenarios, this study introduces a one-dimensional transient heat transfer model that can efficiently capture the time-dependent thermal dynamics of this novel glazing system. Based on the numerical solutions using the explicit finite difference method (FDM), the temperature profile of the vacuum PV glazing can be obtained dynamically. Consequently, the heat gain of the semi-transparent vacuum PV glazing can be calculated under time-varying outdoor and indoor conditions. The validated heat transfer model was applied under four different scenarios, viz. summer daytime, summer nighttime, winter daytime, and winter nighttime, to provide a detailed analysis of the dynamic thermal behaviour, including the temperature variation and the energy flow. The dynamic thermal characteristics of the vacuum PV glazing calculated by the transient heat transfer model demonstrate its excellent thermal insulation and solar control capabilities. Moreover, the thermal performance of vacuum PV glazing was compared with a standard double-pane window under various weather conditions of a typical summer day and a typical winter day. The results indicate that the vacuum PV glazing can effectively minimise both heat gain and heat loss. The fluctuation of the inner surface temperature can be controlled within a limited range away from the set point of the indoor room temperature. Therefore, the vacuum PV glazing contributes to stabilising the temperature of the indoor environment despite the fluctuating solar radiation and periodic outdoor temperature. It is suggested that the vacuum PV glazing has the potential to enhance the climate adaptability of BIPV windows under different climate backgrounds. Full article

Background: Monolithic zirconia has attracted considerable interest in dentistry due to its favorable physical and mechanical properties, making it a promising alternative for crown fabrication. Nonetheless, a standardized finishing protocol for this material has yet to be established. Objective: This study aimed to evaluate the surface characteristics and in vitro biofilm formation of zirconia finished by either polishing or glazing. Methods: A total of 72 zirconia specimens were fabricated and divided into control, glazing, and polishing groups. Surface analysis included roughness, wettability, and surface free energy. Microbiological analysis included CFU (colony-forming units per mL) counts, microbial adhesion at 2, 4, 6, and 8 h, biofilm biovolume, and qualitative biofilm assessment via scanning electron microscopy (sEm). Results: The glazing group showed significantly greater roughness than the polishing (p = 0.006) and control (p = 0.016) groups, along with a lower contact angle (polishing—p = 0.002; control—p < 0.001) and higher surface energy (polishing—p = 0.005; control—p < 0.001). No significant differences were observed in CFU counts for the tested microorganisms (C. albicans, p = 0.158; L. casei, p = 0.610; S. mutans, p = 0.904). Regarding microbial adhesion, the polishing group showed a smaller biofilm-covered area compared to the control group for both total biofilm (p = 0.008) and viable biofilm (p = 0.005). no statistically significant difference was observed in biofilm biovolume (p = 0.082). Conclusions: These findings suggest that, despite the surface differences among the groups, biofilm formation was not significantly affected. Full article

To address the issue of surface glazing that occurs during prolonged polishing with gel tools, this study employs a triethanolamine (TEA)-based polishing fluid system to enhance the self-sharpening capability of the gel polishing disc. The inhibitory mechanism of TEA concentration on disc glazing is systematically analyzed, along with its impact on the gel disc’s frictional wear behaviour. Furthermore, the synergistic effects of process parameters on both surface quality and material removal rate (MRR) of SiC are examined. The results demonstrate that TEA concentration is a critical factor in regulating polishing performance. At an optimal concentration of 4 wt%, an ideal balance between chemical chelation and mechanical wear is achieved, effectively preventing glazing while avoiding excessive tool wear, thereby ensuring sustained self-sharpening capability and process stability. Through orthogonal experiment optimization, the best parameter combination for SiC polishing is determined: 4 wt% TEA concentration, 98 N polishing pressure, and 90 rpm rotational speed. This configuration delivers both superior surface quality and desirable MRR. Experimental data confirm that TEA significantly enhances the self-sharpening performance of gel discs through its unique complex reaction. During the rough polishing stage, the MRR increases by 34.9% to 0.85 μm/h, while the surface roughness S_a is reduced by 51.3% to 6.29 nm. After subsequent CMP fine polishing, an ultra-smooth surface with a final roughness of 2.33 nm is achieved. Full article

This in vitro study aimed to compare the effects of various surface treatments and hydrothermal aging on the phase composition, microstructure, and compressive strength of dental zirconia (ZrO₂). Forty-eight zirconia cubes (8 × 8 × 8 mm) were fabricated using CAD/CAM from two materials: infrastructure zirconia (Group S1) and super-translucent multilayered monolithic zirconia (Group S2). Four samples of each material were analyzed in their pre-sintered state (S1-0, S2-0). The remaining specimens were sintered and assigned to sub-groups based on surface treatment: untreated, sandblasted with 30 µm or 50 µm Al₂O₃, polished, or polished and glazed. Characterization was performed using EDX, SEM, XRD with Rietveld refinement, Raman spectroscopy, and compressive testing before and after accelerated hydrothermal aging, according to EN ISO 13356:2015. EDX revealed a higher yttria content in monolithic zirconia (10.57 wt%) than in infrastructure zirconia (6.51 wt%). SEM images showed minimal changes in polished samples but clear surface damage after sandblasting, which was more pronounced with larger abrasive particles. XRD and Raman confirmed that sandblasting promoted the tetragonal (t-ZrO₂) to monoclinic (m-ZrO₂) phase transformation (t→m), amplified further by hydrothermal aging. The polished groups showed greater phase stability post-aging. Compressive strength decreased in all treated and aged samples, with monolithic zirconia being more affected. Polished samples displayed the best surface quality and structural resilience across both materials. These findings underline the impact of clinical surface treatments on zirconia’s long-term mechanical and structural behavior. Full article

Ice formation on critical infrastructure such as wind turbine blades can lead to severe performance degradation and safety hazards. This study investigates the use of hyperspectral imaging (HSI) combined with machine learning to detect and classify ice on various coated and uncoated surfaces. Hyperspectral reflectance data were acquired using a push-broom HSI system under controlled laboratory conditions, with ice and rime ice generated using a thermoelectric cooling setup. Support Vector Machine (SVM) and Random Forest (RF) classifiers were trained on uncoated aluminum samples and evaluated on surfaces with different coatings to assess model generalization. Both models achieved high classification accuracy, though performance declined on black-coated surfaces due to increased absorbance by the coating. The study further examined the impact of spectral band reduction to simulate different sensor types (e.g., NIR vs. SWIR), revealing that model performance is sensitive to wavelength range, with SVM performing optimally in a reduced band set and RF benefiting from the full spectral range. A multiclass classification approach using RF successfully distinguished between glaze and rime ice, offering insights into more targeted mitigation strategies. The results confirm the potential of HSI and machine learning as robust tools for surface ice monitoring in safety-critical environments. Full article

Thermal comfort of occupants is characterized by operative temperature (Top), while thermal environment is usually controlled by air temperature (Ta). For perimeter areas in buildings, the use of Ta in the control may lead to uncomfortable conditions. In this paper, thermostat controls based on air (TC-Ta) and Top (TC-Top) were compared in an office module based on different glazing ratio (GR) and indoor units. The results showed that, for a fan–coil system, with TC-Top, thermal comfort can be better, while for a ceiling panel system thermal comfort was similar with both controls. For fan coils, with TC-Top, Ta in offices became higher in the winter and lower in the summer, which improved thermal comfort along with increased energy use. For both GR conditions, the radiant panel could compensate for the presence of cold/warm surfaces, and it decreased the differences between the two controls, especially during cooling, which made the radiant system more suitable in large GR condition. With TC-Top, for the ceiling panel system, the increment of energy use was quite small. According to the results, under large GR, TC-Top was better for the fan–coil system to assure thermal comfort, and both control methods could be used in ceiling panel system. This study presents a comprehensive comparison of the two control strategies for both convective and radiant systems, highlighting their performance under varying GR conditions. The results also provide guidance for the optimal control of different indoor units under different GR conditions. Full article

In the context of global warming, building transformation takes on a dual responsibility to be more energy-efficient and sustainable for climate change mitigation and to be more climate-resilient for occupants’ comfort. The building energy retrofitting is an urgent need due to the large amount of existing building stock. Especially in high-rise and high-density cities under a subtropical climate, like Hong Kong, existing buildings with large glazed façades face the challenges of high energy consumption and overheating risks. An advanced glazing system, namely the vacuum insulating glazing (VIG), shows the potential for effective building envelope retrofitting due to its excellent thermal insulation ability. Yet, its performance for practical applications in the subtropical region has not been investigated. To enhance the energy performance and thermal comfort of existing high-rise buildings, this study proposed a novel retrofitting approach by integrating the VIG into the existing window system as secondary glazing. Field experiments were conducted in a commercial building in Hong Kong to investigate the thermal performance of the VIG retrofit application under real-world conditions. Furthermore, the energy-saving potential and thermal comfort performance of the VIG retrofit were evaluated by building energy simulations. The experimental results indicate that the VIG retrofit can effectively stabilize the fluctuation of the inside glass surface temperature and significantly reduce the heat gain by up to 85.3%. The simulation work shows the significant energy-saving potential of the VIG retrofit in Hong Kong. For the VIG retrofit cases under different scenarios, the energy-saving potential varies from 12.5% to 29.7%. In terms of occupants’ thermal comfort, the VIG retrofit can significantly reduce the overheating risk and improve thermal satisfaction by 9.2%. Due to the thermal comfort improvement, the cooling setpoint could be reset to 1 °C higher without compromising the overall thermal comfort. The average payback period for the VIG application is 5.8 years and 8.6 years for the clear glass retrofit and the coated glass retrofit, respectively. Therefore, the VIG retrofit approach provides a promising solution for building envelope retrofits under subtropical climate conditions. It not only benefits building owners and occupants but also contributes to achieving long-term climate resilience and the carbon neutrality of urban areas. Full article

This study aimed to investigate the impact of varying concentrations of graphene oxide (GO) combined with two surface coating agents (SCAs) and two dental adhesives (DAHs) used as SCAs on microhardness. Two SCAs, Resin Glaze (ReG) and Coat-It (CoI) (Shofu Inc., Kyoto, Japan), along with two DAHs, Adper^TM Scotchbond^TM Multi-purpose Adhesive (AdA) (3M ESPE, Seefeld, Germany) and OptiBond^TM FL Adhesive (OpA) (Kuraray Noritake Dental Inc., Okayama, Japan), were tested. The ten concentrations of GO—0 wt % (control), 0.05 wt %, 0.1 wt %, 0.3 wt %, 0.5 wt %, 0.7 wt %, 1 wt %, 2 wt %, 5 wt %, and 10 wt %—were incorporated into the SCAs and DAHs to create the experimental formulations. These mixtures underwent centrifugation for homogenization, followed by sonication for dispersion. The mixture was poured into the 3D-printed resin mold (10 mm in diameter and 1 mm in height) and then cured with a light curing unit for 180 s. The cured specimens were then kept in distilled water at 37 ± 1 °C for 24 h. All specimens were then subjected to evaluation of their microhardness properties using a Knoop hardness testing machine. Data were collected, and the statistical analysis was conducted using Two-way ANOVA followed by Tukey’s post-hoc tests at a 0.05 level of significance. According to the results, surface hardness was significantly increased (p < 0.05) when 0.3–0.7 wt % of GO was added to ReG, CoI, and AdA, compared to the control group. However, surface hardness was significantly increased (p < 0.05) when 0.05–0.3 wt % of GO was added to OpA compared to the control group. In the control groups, the microhardness of OpA was significantly higher than that of the other groups (p < 0.05). In the 0.1 wt % groups, the microhardness of OpA was significantly higher than that of the other groups (p < 0.05). At 0.5 wt %, ReG, CoI, and AdA showed significantly higher microhardness compared to their respective control groups (p < 0.05). In the 1–10 wt % groups, the microhardness of ReG, CoI, and AdA demonstrated a gradual, significant decrease compared to the 0.7 wt % groups. Whereas in the 0.5–10 wt % groups, the microhardness of OpA showed a significant gradual decrease compared to the 0.3 wt % group. In summary, the optimal GO concentration could improve the surface hardness of ReG, CoI, AdA, and OpA. Full article

Adaptive façades, also known as climate-adaptive building shells (CABSs), could make a significant contribution towards reducing the energy consumption of buildings and their environmental impacts. There is extensive research on glazed adaptive façades, mainly due to the available technology for glass materials. The technological development of opaque adaptive façades has focused on variable-thermal-resistance envelopes, and the simulation of this type of façade is a challenging task that has not been thoroughly studied. The aim of this study was to configure and validate a simplified office model that could be used for simulating an adaptive façade with variable thermal resistance via adaptive insulation thickness in its opaque part. Software-to-software model comparison based on the results of an EnergyPlus Building Energy Simulation Test 900 (BesTest 900)-validated model was used. Cooling and heating annual energy demand (kWh), peak cooling and heating (kW), and maximum, minimum, and average annual hourly zone temperature variables were compared for both the Adaptive and non-adaptive validated model. An Adaptive EnergyPlus model based on the BesTest 900 model, which uses the EnergyPlus SurfaceControl:MovableInsulation class list, was successfully validated and could be used for studying office buildings with a variable-thermal-resistance adaptive façade wall configuration, equivalent to a heavyweight mass wall construction with an External Insulation Finishing System (EIFS). An example of the Adaptive model in the Denver location is included in this paper. Annual savings of up to 26% in total energy demand (heating + cooling) was achieved and could reach up to 54% when electro-chromic (EC) glass commanded by a rule-based algorithm was added to the glazed part of the variable-thermal-resistance adaptive façade. Full article

Objectives: To examine the effects of surface treatments on the color stability, surface roughness, surface gloss, and wettability of monolithic polychromatic material jetting (MJT) 3D-printed denture material. Material and Methods: Twenty-one color variants of the same denture material (TrueDent; Stratasys, Eden, MN, USA) underwent two surface treatments (polishing only or polishing and glazing), creating 42 study groups with a total of 420 samples (n = 10 per group). The samples were manufactured using a PolyJet 3D printer (J5 DentaJet; Stratasys, Eden, MN, USA), a type of MJT 3D printer. Color measurements were taken with a digital spectrophotometer before and after the surface treatments, and quantitative color differences (ΔE₀₀ and ΔC*) were calculated using the CIE2000 system. Comparisons of ΔE₀₀ were made against the 50%:50% acceptability threshold (AT) of 1.8 and the 50%:50% perceptibility threshold (PT) of 0.8 for tooth shade, as well as the 50%:50% PT of 1.72 and the 50%:50% AT of 4.08 for gingival (pink) shade. After surface treatment, the gloss was measured using a glossmeter, surface roughness was measured with optical profilometry, and wettability was measured by contact angle measurements using an optical tensiometer. The significance of surface treatment on color changes for each color variant was evaluated using one-sided, one-sample t-tests against the AT and PT. The effects of surface treatment on surface gloss, surface roughness, contact angle, and ΔC* were analyzed using t-tests for each color variant. Pairwise comparisons between groups were made using Fisher’s Protected Least Significant Differences (α = 0.05). Results: In most cases, glazing caused the color change (ΔE₀₀) to exceed the AT and PT, with a few exceptions. Most materials exhibited a more vibrant (more saturated) appearance and statistically higher chroma, with glazed surface treatments compared to polished ones, though there were some exceptions. For all materials, the glazed samples had significantly higher gloss units than the polished ones (p < 0.0001). Additionally, all materials showed significantly higher surface roughness in glazed samples compared to polished ones (p < 0.0001 for most). The polished samples had significantly higher contact angles (p < 0.0001 for most). Conclusions: Surface treatments significantly influenced the color, surface gloss, surface roughness, and wettability of MJT 3D-printed denture materials. Glazing led to increased chroma and gloss and produced more hydrophilic surfaces, although it also increased surface roughness. These results highlight the importance of surface treatment selection in optimizing the clinical performance of MJT-fabricated dentures. Full article

Additive manufacturing (AM) of ceramics presents a promising approach for the production of complex sanitaryware prototypes, offering advantages in terms of cost and time to market. This study explores binder jetting (BJ) as an optimal AM technique due to its ability to process ceramic materials without thermal stress, accommodate various compositions, and produce large components without support structures. A combination of refractory cement, feldspathic sands, quartz, and calcined alumina was used to formulate 19 different compositions, ensuring adequate green strength and minimizing shrinkage during sintering. A hydration-activated binding method with a water-based binder was employed to enhance part formation and mechanical properties. The results indicate that compositions containing calcined alumina exhibited lower pyroplastic deformation, while optimized gelling agent concentrations improved green strength and dimensional accuracy. The final selected material (SA18) demonstrated high compressive strength, low shrinkage, and a surface roughness comparable to traditional sanitaryware. The application of an engobe layer improved glaze adherence, ensuring a homogeneous surface. This study highlights binder jetting as a viable alternative to traditional ceramic processing, paving the way for its adoption in industrial sanitaryware manufacturing. Full article

This study investigates the application of terahertz frequency-modulated continuous-wave (FMCW) imaging for the non-destructive inspection of a historical enamel plate, using both reflection and transmission modes. A 300 GHz FMCW radar system was employed to capture high-resolution images of the plate’s internal and surface structures. Through optimized data acquisition and processing, the system successfully revealed subsurface features such as fractures, as well as surface-level textural variations linked to the decorative glazes. Although pigment differentiation remains a challenge, contrast variations observed in THz images suggest correlations with material composition. The results highlight the potential of FMCW terahertz imaging as a compact, rapid, and non-contact diagnostic tool for cultural heritage analysis. Its practicality and adaptability make it particularly suitable for in situ inspections in museums or restoration contexts. Full article

Purpose Maintaining the surface quality of ceramic restorations after clinical adjustments is critical for both aesthetic outcomes and long-term oral health, yet the optimal approach to restoring gloss and smoothness remains unclear. The purpose of this study is to investigate the effect of different surface finishing and grinding procedures on the surface gloss and roughness of three different monolithic lithium disilicate ceramics and one monolithic ultra-translucent zirconia ceramic. Materials and Methods A total of 104 specimens (1.5 × 12 × 14 mm) were prepared from four ceramic materials: LiSi CEREC Tessera (CT), GC Initial LiSi (LS), IPS e.max CAD (EC), and zirconia disc (KATANA UTML (KAT)). Each was divided into two subgroups based on surface finishing (mechanical polishing or glazing; n = 10). Gloss and surface roughness were measured using a glossmeter and a profilometer, respectively. One specimen per subgroup was analyzed under SEM at ×1000 magnification. Results Gloss and roughness values were analyzed with the two-way robust ANOVA test and multiple comparisons were made with Bonferroni correction. The significance level was set at p < 0.05. Mechanical polishing, glazing, and repolishing increased the gloss values of the materials, with the KAT group achieving the highest gloss in the repolishing groups. The lowest gloss values were observed in the grinding groups. Additionally, these surface treatments reduced the roughness of the surface of all the materials. Conclusions Surface finishing procedures significantly influenced the gloss and roughness of monolithic lithium disilicate and zirconia ceramics. Mechanical polishing systems performed similarly or better than glazing. However, selecting an appropriate polishing system for each material is essential. Full article

Hybrid building construction, in which the steel frame is filled with modular panels made of wood, is a relatively new technical solution. This type of structure allows the integration of large window surfaces. The aim of this study is to indicate the optimal glazing system, taking into account energy consumption, thermal comfort and economic indicators. A house made using new hybrid technology with an area of 152.4 m², located in Bialystok (Northeastern Poland) and in Kiruna (Northern Sweden), was selected as the reference object. Energy simulations of this building were performed with DesignBuilder v. 6.1.8.021 software. Due to the large format of the glazing, the assessment of the thermal environment was performed using the PMV index. An economic analysis aimed at selecting the optimal type of glazing was carried out. It was based on the most commonly used indicators such as LCC, NPV and IRR. The results of this study indicated that the selection of triple-glazed windows in the reference house reduced energy demand by over 22% for Bialystok and about 24% for Kiruna compared to double-glazed windows. Even greater effects can be achieved by using quadruple-glazed windows, as they provide energy savings of 36% and 39%, respectively, for these locations. The results of the analysis performed for a 2% increase in energy prices showed that triple and quadruple windows had a similar LCC value when the discount rate was lower than 2.5% for the Bialystok site. Quadruple-glazed windows were the best option for the Kiruna site when the discount rate was less than 5%. This research study found that, assuming a stable financial situation and a small increase in energy prices, it is recommended to use triple-glazed windows in the climate of Northeastern Poland. In more severe weather conditions, for example those characteristic of the area of Northern Sweden, quadruple-glazed windows are recommended. Full article

This study explores the integration of Building Information Modeling (BIM) and Geographic Information Systems (GISs) to enhance sustainable energy efficiency and flood resilience in residential buildings, with a case study from Quetta, Pakistan. The research leverages BIM to optimize energy performance through scenario-based energy consumption assessments, thermal efficiency, material properties, and groundwater considerations, ensuring structural integrity against water infiltration. Enhanced insulation and double-glazed windows reduced energy use by 11.78% and 5.8%, respectively, with monthly energy cost savings of up to 48.2%. GIS tools were employed for high-resolution flood risk analysis, utilizing Digital Elevation Models (DEMs) and hydrological data to simulate flood scenarios with depths of up to 2 m, identifying vulnerabilities and estimating non-structural damage costs at PKR 250,000 (~10% of total building costs). Groundwater data were also incorporated to evaluate their impact on foundation stability, ensuring the building’s resilience to surface and subsurface water challenges. A novel BIM-GIS integration framework provided precise 2D and 3D visualizations of flood impacts, facilitating accurate damage assessments and cost-effective resilience planning. The findings demonstrated that incorporating flood-resistant materials and design modifications could reduce repair costs by 30–50%, highlighting the cost-efficiency of sustainable resilience strategies. This research advances sustainable and resilient construction practices by showcasing the dual potential of BIM-GIS integration to address energy efficiency and groundwater-related structural vulnerabilities alongside hazard mitigation challenges. Future applications include automating workflows, integrating renewable energy systems, and validating models across diverse climatic regions to promote the global adoption of innovative urban planning solutions. Full article