Search Results (1,347)

Crop leaves naturally exhibit a curved morphology and primarily display bending deformation and vibrational responses under wind load. The curved surface structure of leaves plays a critical role in the deposition and retention of pesticide droplets. In this study, wind tunnel experiments combined with high-speed photography and digital image analysis were conducted to systematically investigate the curvature and flexibility distributions of three typical crop leaves: walnut, peach, and pepper, across a range of wind speeds. The results indicate that with increasing wind speed, all three types of leaves gradually transition from smooth, uniform bending to a multi-peak pattern of pronounced local curvature, with increasingly prominent nonlinear deformation characteristics. Moreover, once the wind speed exceeds the critical threshold of 6 m/s, the primary deformation region generally shifts from the leaf base to the tip. For example, the maximum curvature of walnut leaves increased from 0.018 mm⁻¹ to 0.047 mm⁻¹, and that of pepper leaves from 0.031 mm⁻¹ to 0.101 mm⁻¹, both more than double their original values. In addition, all three types of leaves demonstrated a distinct structural gradient characterized by strong basal rigidity and high apical flexibility. The tip flexibility values exceeded 1.5 × 10⁻⁵, 4 × 10⁻⁴, and 5.6 × 10⁻⁴ mm⁻²·mN⁻¹ for walnut, peach, and pepper leaves, respectively. These findings elucidate the mechanical response mechanisms of non-uniform flexible crop leaves under wind-induced bending and provide a theoretical basis and data support for the optimization of air-assisted spraying parameters. Full article

High strength and high ductility concrete (HSHDC) exhibit exceptional compressive strength (up to 90 MPa) and remarkable tensile ductility (ultimate tensile strain reaching 6%), making them highly resilient under impact loading. To elucidate the influence of strain rate and wet–dry cycling of salt spray on the dynamic compressive response of HSHDC, a series of tests was conducted using a 75 mm split Hopkinson pressure bar (SHPB) system on specimens exposed to cyclic corrosion for periods ranging from 0 to 180 days. The alternating seasonal corrosion environment was reproduced by using a programmable walk-in environmental chamber. Subsequently, both uniaxial compression and SHPB tests were employed to evaluate the post-corrosion dynamic compressive properties of HSHDC. Experimental findings reveal that corrosive exposure significantly alters both the static and dynamic compressive mechanical behavior and constitutive characteristics of HSHDC, warranting careful consideration in long-term structural integrity assessments. As corrosion duration increases, the quasi-static and dynamic compressive strengths of HSHDC exhibit an initial enhancement followed by a gradual decline, with stress reaching its peak at 120 days of corrosion under all strain rates. All specimens demonstrated pronounced strain-rate sensitivity, with the dynamic increase factor (DIF) being minimally influenced by the extent of corrosion under dynamic strain rates (112.6–272.0 s⁻¹). Furthermore, the peak energy-consumption capacity of HSHDC was modulated by both the duration of corrosion and the applied strain rate. Full article

The concerning increase in respiratory infections that are resistant to multiple drugs has led to a growing interest in bacteriophage therapy as a potential alternative to conventional antibiotics. Effective phage delivery to the lungs, however, presents several formulation and stability issues, particularly for inhalation-based methods. This review highlights current developments in the creation of dry powder formulations that can be inhaled for pulmonary phage therapy, with a focus on encapsulation methods based on nanoparticles, such as solid lipid nanoparticles (SLNs) and polymer-based nanoparticles. These carriers enhance the aerodynamic characteristics of phages, making them suitable for deep lung deposition, while also protecting them during processing and storage. Several drying methods have been investigated to create powders with optimal morphologies, porosity, and dispersibility, including spray drying and spray freeze drying. The review also emphasizes how the phage morphotype affects stability, especially when nebulization stress is present. Furthermore, the advantages of nanoparticle matrices are confirmed by the reduced viability loss (usually< 0.5 log PFU) of encapsulated phages. Standardizing production processes, scaling up, and ensuring regulatory compliance remain challenging despite encouraging preclinical results. The combination of phage therapy with nanotechnology creates new avenues for the utilization of inhalable delivery methods to treat multidrug-resistant pulmonary infections. To translate these novel formulations from preclinical development to clinical application, sustained multidisciplinary collaboration across pharmaceutical sciences, microbiology, and clinical pharmacology is essential. Full article

In the present work, the influence of technological parameters of detonation sputtering, in particular the degree of barrel filling, on the properties of chromium oxide (Cr₂O₃) coatings was investigated. Coatings were obtained under different sputtering conditions and analyzed comprehensively using X-ray phase analysis, optical and electron microscopy, and measurements of microhardness, porosity, and tribological characteristics. The results showed that the degree of barrel filling significantly affects the microstructure, thickness, porosity, and mechanical properties of the coatings. The sample obtained at 58% barrel filling showed the lowest porosity (0.01%), uniform distribution of chromium oxide, and the best adhesion, which makes it possible to consider this mode as optimal for the formation of wear-resistant coatings by detonation spraying. Full article

Near-nozzle atomization characteristics in air-assisted spraying were investigated through a novel 3D transient model integrating Volume-of-Fluid and Large Eddy Simulation (VOF-DPM) methods, with experimental validation of droplet distributions (Malvern analyzer) and coating thickness profiles. Key findings reveal that (1) the spray field stabilizes within 30 mm downstream, achieving 80% atomization efficiency (droplets ≤ 100 μm) at 27.5 mm axial distance; (2) radial momentum originates dually from fan-shaped airflow (max 595 m/s) and transverse motion induced by central atomizing air entrainment—a previously unreported mechanism; (3) paint loading delays flow stabilization to 2.5 ms (vs. 0.7 ms for gas-only flow) while reducing peak axial velocity by 18%–22% due to gas–liquid momentum exchange; (4) auxiliary and fan airflows synergistically constrain dispersion, forming elliptical sprays with characteristic cone angles of 61.7° (short axis) and 99.1° (long axis). Significantly, surface tension plays a dual role in inhibiting droplet atomization while promoting ligament pinch-off at 8.1 mm breakup length. These results provide the first quantitative characterization of gas–liquid interactions in near-nozzle regions, enabling precise parameter control for enhanced coating uniformity on complex surfaces. Full article

This article proposes a standard protocol to produce bacterial nanocellulose (Komagateibacter medellinensis). It will briefly review the main raw materials (common agro-industrial waste in tropical countries), process of obtaining bacterial nanocellulose membranes, and the cleaning process for said membranes. The processing of the membranes using a grinder and Ultra-Turrax is then shown, listing the characteristics provided by each of these methods to produce bacterial nanocellulose microparticles by spray drying. The average microparticle size obtained by spray drying was (4.76 ± 1.12 µm), and thermal stability (maximum degradation temperature) was 345 °C. This research clearly states that the grinder was selected as the most efficient mechanical method due to its improved dispersion performance and lower clogging during spray drying. Finally, physical (scanning electron microscopy-SEM, transmission electron microscopy-TEM, and thermogravimetric analyzer-TGA) and microbiological (mesophiles, yeasts, fungi, and fecal coliforms) characterization is demonstrated. These microparticles are intended to be used in the food industry to produce functional and enriched foods, protecting the bioactive components of interest. Full article

The escalating challenges of greenhouse gas emissions, coupled with the severe depletion of oil reserves and the surging global energy demand, have emerged as critical concerns requiring urgent attention. Against this backdrop, biodiesel has been recognized as a viable alternative fuel for compression ignition (CI) engines. The primary objective of this research is to review the application of biodiesel in CI engines, with a focus on enhancing fuel properties and improving atomization performance. This article examines the spray and atomization characteristics of biodiesel fuels and conducts a comparative analysis with diesel fuel. The results show that biodiesel has a longer spray tip penetration, smaller spray cone angle, larger Sauter mean diameter (SMD) and faster droplet velocity due to its higher viscosity and surface tension. Blending with other fuels, such as ethanol, butanol, dimethyl ether (DME) and di-n-butyl ether, results in reduced viscosity and surface tension in these mixed fuels, representing a simple and effective approach for improving biodiesel atomization performance. A comprehensive analysis of spray and droplet impingement is also conducted. The findings reveal that biodiesel exhibits a higher probability of fuel–wall impingement, suggesting that future research should focus on two key directions: first, developing combined strategies to enhance impact-induced secondary atomization while minimizing fuel deposition; and second, investigating single-droplet impingement, specifically that of microscale biodiesel droplets and blended fuel droplets under real engine operating conditions. This paper also presents several advanced techniques, including air-assisted atomization, dual-fuel impingement, nano-biodiesel, and water-emulsified biodiesel, aimed at mitigating the atomization limitations of biodiesel, thereby facilitating the broader adoption of biodiesel in compression ignition engines. Full article

With the advancement of precision agriculture, variable-rate spraying (VRS) technology has demonstrated significant potential in enhancing pesticide utilization efficiency and promoting environmental sustainability, particularly in orchard applications. As a critical medium for pesticide transport, the dynamic structural characteristics of orchard canopies exert a profound influence on spraying effectiveness. This review systematically summarizes recent progress in the dynamic perception and modeling of orchard canopies, with a particular focus on key sensing technologies such as LiDAR, Vision Sensor, multispectral/hyperspectral sensors, and point cloud processing techniques. Furthermore, it discusses the construction methodologies of static, quasi-dynamic, and fully dynamic canopy modeling frameworks. The integration of canopy sensing technologies into VRS systems is also analyzed, including their roles in spray path planning, nozzle control strategies, and precise droplet transport regulation. Finally, the review identifies key challenges—particularly the trade-offs between real-time performance, seasonal adaptability, and modeling accuracy—and outlines future research directions centered on multimodal perception, hybrid modeling approaches combining physics-based and data-driven methods, and intelligent control strategies. Full article

Zirconia is used widely for high-precision custom abutments; however, stress concentration can compromise osseointegration. Although glass–ceramic spray deposition (GCSD) can enhance the surface properties of zirconia, its biological effects remain unclear. In this study, the biological responses of human osteoblast-like (MG-63) cells to GCSD-modified zirconia surfaces were evaluated to assess the potential application in zirconia abutments. Disk-shaped zirconia and titanium alloy samples were prepared; titanium served as the control (Ti). Zirconia was subjected to polishing (NT), airborne-particle abrasion (AB), or GCSD with (GE) or without (GC) hydrofluoric acid (HF) etching. Surface characteristics, including wettability, surface energy (SE), and surface potential (SP), were analyzed. Cytotoxicity and MG-63 cell adhesion were assessed using the PrestoBlue assay, scanning electron microscopy (SEM), viability staining, and confocal laser scanning microscopy (CLSM). Statistical analysis was performed with a significance level of 0.05. GCSD produced a dense glass–ceramic coating on the zirconia surface, which significantly enhanced hydrophilicity as indicated by reduced water contact angles and increased SE in the GC and GE groups (p < 0.05). HF etching increased SP (p < 0.05). No cytotoxicity was observed in any group. SEM, viability staining, and CLSM revealed enhanced MG-63 cell attachment on Ti and GE surfaces and the highest viability ratio in the GE group. The NT group exhibited the lowest cell attachment and viability at all time points. GCSD effectively improved zirconia abutment surface properties by enhancing hydrophilicity and promoting MG-63 cell adhesion, with biocompatibility comparable to or better than that of titanium. Full article

Jabuticaba (Myrciaria jaboticaba (Vell.) O. Berg) peel is a native Brazilian fruit by-product recognized for its high anthocyanin (ANC) content and strong antioxidant potential, making it a valuable natural source for food applications. This study aimed to optimize the extraction and spray drying-based encapsulation of ANCs from the peels of Sabará jabuticaba. Extraction was performed using ethanol acidified with HCl (6 M) under varying conditions of pH (1.0–3.0), temperature (14–50 °C), and solvent volume (100–250 mL). The highest anthocyanin yield (328.13 mg/100 g dry basis) was achieved at pH 1.0, 50 °C, and 250 mL solvent volume. For encapsulation, gum arabic and maltodextrin were used as wall materials at different mass ratios (1:1, 1:2, 1:3, 1:4, 2:1, 3:1, and 4:1 w/w). The 1:2 ratio (gum arabic/maltodextrin) resulted in the highest retention of anthocyanins (315.37 mg/100 g dry basis), with encapsulation efficiency of approximately 96%, low water activity (0.27), and reduced moisture content (3.6%). These characteristics are essential for ensuring product stability during storage. The optimized anthocyanin-rich microparticles present promising potential for application as natural colorants and functional ingredients in food formulations or as antioxidant carriers in pharmaceutical products. Full article

The efficiency of electric motors is highly dependent on their operating temperature, with lower temperatures contributing to enhanced performance, reliability, and extended service life. This study presents a comprehensive review of state-of-the-art cooling technologies and evaluates their impact on the thermal behavior of a commercial motor–generator system in high-demand applications. A baseline model of a permanent magnet synchronous motor (PMSM) was developed using MotorCAD 2023^® software, which was supported by reverse engineering techniques to accurately replicate the motor’s physical and thermal characteristics. Subsequently, multiple cooling strategies were simulated under consistent operating conditions to assess their effectiveness. These strategies include conventional axial water jackets as well as advanced oil-based methods such as shaft cooling and direct oil spray to the windings. The integration of these systems in hybrid configurations was also explored to maximize thermal efficiency. Simulation results reveal that hybrid cooling significantly reduces the temperature of critical components such as stator windings and permanent magnets. This reduction in thermal stress improves current efficiency, power output, and torque capacity, enabling reliable motor operation across a broader range of speeds and under sustained high-load conditions. The findings highlight the effectiveness of hybrid cooling systems in optimizing both thermal management and operational performance of electric machines. Full article

This study aimed to develop a functional powder using whey and milk matrices, leveraging the protective capacity of chia–alginate hydrogels and the advantages of electrohydrodynamic spraying (EHDA), a non-thermal technique suitable for encapsulating probiotic cells under stress conditions commonly encountered in food processing. A hydrogel matrix composed of chia seed mucilage and sodium alginate was used to form a biopolymeric network that protected probiotic cells during processing. The encapsulation efficiency reached 99.0 ± 0.01%, and bacterial viability remained above 9.9 log₁₀ CFU/mL after lyophilization, demonstrating the excellent protective capacity of the hydrogel matrix. Microstructural analysis using confocal laser scanning microscopy (CLSM) revealed well-retained cell morphology and homogeneous distribution within the hydrogel matrix while, in contrast, scanning electron microscopy (SEM) showed spherical, porous microcapsules with distinct surface characteristics influenced by the encapsulation method. Encapsulates were incorporated into beverages flavored with red fruits and pear and subsequently freeze-dried. The resulting powders were analyzed for moisture, protein, lipids, carbohydrates, fiber, and color determinations. The results were statistically analyzed using ANOVA and response surface methodology, highlighting the impact of ingredient ratios on nutritional composition. Raman spectroscopy identified molecular features associated with casein, lactose, pectins, anthocyanins, and other functional compounds, confirming the contribution of both matrix and encapsulants maintaining the structural characteristics of the product. The presence of antioxidant bands supported the functional potential of the powder formulations. Chia–alginate hydrogels effectively encapsulated L. reuteri, maintaining cell viability and enabling their incorporation into freeze-dried beverage powders. This approach offers a promising strategy for the development of next-generation functional food gels with enhanced probiotic stability, nutritional properties, and potential application in health-promoting dairy systems. Full article

The multiscale interactive system composed of wind, leaves, and droplets serves as a critical dynamic unit in precision orchard spraying. Its coupling mechanisms fundamentally influence pesticide transport pathways, deposition patterns, and drift behavior within crop canopies, forming the foundational basis for achieving intelligent and site-specific spraying operations. This review systematically examines the synergistic dynamics across three hierarchical scales: Droplet–leaf surface wetting and adhesion at the microscale; leaf cluster motion responses at the mesoscale; and the modulation of airflow and spray plume diffusion by canopy architecture at the macroscale. Key variables affecting spray performance—such as wind speed and turbulence structure, leaf biomechanical properties, droplet size and electrostatic characteristics, and spatial canopy heterogeneity—are identified and analyzed. Furthermore, current advances in multiscale modeling approaches and their corresponding experimental validation techniques are critically evaluated, along with their practical boundaries of applicability. Results indicate that while substantial progress has been made at individual scales, significant bottlenecks remain in the integration of cross-scale models, real-time acquisition of critical parameters, and the establishment of high-fidelity experimental platforms. Future research should prioritize the development of unified coupling frameworks, the integration of physics-based and data-driven modeling strategies, and the deployment of multimodal sensing technologies for real-time intelligent spray decision-making. These efforts are expected to provide both theoretical foundations and technological support for advancing precision and intelligent orchard spraying systems. Full article

The encapsulation of bioactive compounds using proteins as wall materials has emerged as an effective strategy to enhance their stability, bioavailability, and controlled release. Proteins offer unique functional properties, including amphiphilic behavior, gel-forming ability, and interactions with bioactives, making them ideal candidates for encapsulation. Animal-derived proteins, such as whey and casein, exhibit superior performance in stabilizing lipophilic compounds, whereas plant proteins, including soy and pea protein, demonstrate greater affinity for hydrophilic bioactives. Advances in protein modification and the formation of protein–polysaccharide complexes have further improved encapsulation efficiency, particularly for heat- and pH-sensitive compounds. This review explores the physicochemical characteristics of proteins used in encapsulation, the interactions between proteins and bioactives, and the main encapsulation techniques, including spray drying, complex coacervation, nanoemulsions, and electrospinning. Furthermore, the potential applications of encapsulated bioactives in functional foods, pharmaceuticals, and nutraceuticals are discussed, highlighting the role of emerging technologies in optimizing delivery systems. Understanding the synergy between proteins, bioactives, and encapsulation methods is essential for developing more stable, bioavailable, and sustainable functional products. Full article

Considering the serious hazard of respiratory dust in underground coal mines and the low efficiency of traditional dust-reduction technology, this study optimizes the atomisation parameters of the gas–liquid two-phase flow nozzle through numerical simulation and experimental testing, and designs an on-board dust-reduction system. Based on the Fluent software (version 2023 R2), a flow field model outside the nozzle was established, and the effects of the air supply pressure, gas-phase inlet velocity, and droplet mass flow rate on the atomisation characteristics were analyzed. The results show that increasing the air supply pressure can effectively reduce the droplet particle size and increase the range and atomisation angle, and that the dust-reduction efficiency is significantly improved with the increase in pressure. The dust-reduction efficiency reached 69.3% at 0.6 MPa, which was the economically optimal operating condition. Based on the parameter optimization, this study designed an annular airborne gas–liquid two-phase flow dust-reduction system, and a field test showed that the dust-reduction efficiency of this system could reach up to 86.0%, which is 53.5% higher than that of traditional high-pressure spraying, and that the dust concentration was reduced to less than 6 mg/m³. This study provides an efficient and reliable technical solution for the management of underground coal mine dust and guidance for promoting the development of the coal industry. Full article