Search Results (514)

Shandong Province is rich in geothermal resources, mainly stored in sandstone reservoirs. The setting of reasonable well spacing in the early stage of large-scale recharge has not attracted enough attention. The problem of small well spacing in geothermal engineering is particularly prominent in the sandstone thermal reservoir production area represented by Dezhou. Based on the measured data of temperature, flow, and water level, this paper constructs a typical engineering numerical model by using TOUGH2 software. It is found that when the distance between production and recharge wells is 180 m, the amount of production and recharge is 60 m³/h, and the temperature of reinjection is 30 °C, the temperature of the production well will decrease rapidly after 10 years of production and recharge. In order to solve the problem of thermal breakthrough, three optimization schemes are assumed: reducing the reinjection temperature to reduce the amount of re-injection when the amount of heat is the same, reducing the amount of production and injection when the temperature of production and injection is constant, and stopping production after the temperature of the production well decreases. However, the results show that the three schemes cannot solve the problem of thermal breakthrough or meet production demand. Therefore, it is necessary to set reasonable well spacing. Therefore, based on the strata near the Hydrological Homeland in Decheng District, the reasonable spacing of production and recharge wells is achieved by numerical simulation. Under a volumetric flux scenario ranging from 60 to 80 m³/h, the well spacing should exceed 400 m. For a volumetric flux between 80 and 140 m³/h, it is recommended that the well spacing be greater than 600 m. Full article

Channeling in cementing causes interlayer interference, severely restricting oilfield recovery. Existing channeling plugging agents, such as cement and gels, often lead to reservoir damage or insufficient strength. Oil-soluble resin (OSR) particles show great potential in selective plugging of channeling fractures due to their excellent oil solubility, temperature/salt resistance, and high strength. However, their application is limited by the efficient filling and retention in deep fractures. This study innovatively combines the OSR particle plugging system with the mature rapid filtration loss plugging mechanism in drilling, systematically exploring the influence of particle size and sorting on their filtration, packing behavior, and plugging performance in channeling fractures. Through API filtration tests, visual fracture models, and high-temperature/high-pressure (100 °C, salinity 3.0 × 10⁵ mg/L) core flow experiments, it was found that well-sorted large particles preferentially bridge in fractures to form a high-porosity filter cake, enabling rapid water filtration from the resin plugging agent. This promotes efficient accumulation of OSR particles to form a long filter cake slug with a water content <20% while minimizing the invasion of fine particles into matrix pores. The slug thermally coalesces and solidifies into an integral body at reservoir temperature, achieving a plugging strength of 5–6 MPa for fractures. In contrast, poorly sorted particles or undersized particles form filter cakes with low porosity, resulting in slow water filtration, high water content (>50%) in the filter cake, insufficient fracture filling, and significantly reduced plugging strength (<1 MPa). Finally, a double-slug strategy is adopted: small-sized OSR for temporary plugging of the oil layer injection face combined with well-sorted large-sized OSR for main plugging of channeling fractures. This strategy achieves fluid diversion under low injection pressure (0.9 MPa), effectively protects reservoir permeability (recovery rate > 95% after backflow), and establishes high-strength selective plugging. This study clarifies the core role of particle size and sorting in regulating the OSR plugging effect based on rapid filtration loss, providing key insights for developing low-damage, high-performance channeling plugging agents and scientific gradation of particle-based plugging agents. Full article

Small reservoirs have important functions, such as water resource guarantee, flood control and drought resistance, biological habitat and maintaining regional economic development. In order to better clarify the impact of agricultural activities on the nutritional status of water bodies in small reservoirs, zooplankton were quantitatively collected from four small reservoirs in the Jiuxianshan agricultural area of Qufu, Shandong Province, in March and October 2023, respectively. The physical and chemical parameters in sampling points were determined simultaneously. Meanwhile, water samples were collected for nutrient salt analysis, and the eutrophication of water bodies in four reservoirs was evaluated using the comprehensive nutrient status index method. The research found that the species richness of zooplankton after farming (100 species) was significantly higher than that before farming (81 species) (p < 0.05). On the contrary, the dominant species of zooplankton after farming (7 species) were significantly fewer than those before farming (11 species). The estimation results of the standing stock of zooplankton indicated that the abundance and biomass of zooplankton after farming (92.72 ind./L, 0.13 mg/L) were significantly higher than those before farming (32.51 ind./L, 0.40 mg/L) (p < 0.05). Community similarity analysis based on zooplankton abundance (ANOSIM) indicated that there were significant differences in zooplankton communities before and after farming (R = 0.329, p = 0.001). The results of multi-dimensional non-metric sorting (NMDS) showed that the communities of zooplankton could be clearly divided into two: pre-farming communities and after farming communities. The Monte Carlo test results are as follows (p < 0.05). Transparency (Trans), pH, permanganate index (COD_Mn), electrical conductivity (Cond) and chlorophyll a (Chl-a) had significant effects on the community structure of zooplankton before farming. Total nitrogen (TN), total phosphorus (TP) and electrical conductivity (Cond) had significant effects on the community structure of zooplankton after farming. The co-linearity network analysis based on zooplankton abundance showed that the zooplankton community before farming was more stable than that after farming. The water evaluation results based on the comprehensive nutritional status index method indicated that the water conditions of the reservoirs before farming were mostly in a mild eutrophic state, while the water conditions of the reservoirs after farming were all in a moderate eutrophic state. The results show that the nutritional status of small reservoirs in agricultural areas is significantly affected by agricultural activities. The zooplankton communities in small reservoirs underwent significant changes driven by alterations in the reservoir water environment and nutritional status. Based on the main results of this study, we suggested that the use of fertilizers and pesticides should be appropriately reduced in future agricultural activities. In order to better protect the water quality and aquatic ecology of the water reservoirs in the agricultural area. Full article

The establishment and management of nature reserves play a crucial role in protecting biodiversity and supporting sustainable agriculture. This study focuses on 2538 nature reserves in 22 provinces, 5 autonomous regions and 4 municipalities directly under the central government in mainland China. Integrating GIS spatial statistics, imbalance index, and geodetector models, we reveal critical insights: (1) Pronounced spatial inequity is observed, where a small number of eastern provinces dominate the total reserve count, highlighting significant regional disparities in ecological resource allocation. The sparse kernel density in western regions, indicating sparse reserve coverage. The Standard Deviation Ellipse highlights directional dispersion and human-ecological conflicts in high-density zones. (2) Key sustainability indicators driving reserve distribution include: total water resources, water resources per capita, forest area. (3) The spatial distribution of China’s nature reserves, along with factors such as altitude, river distribution, and transportation infrastructure, plays a crucial role in their development. This research provides theoretical support for the scientific planning and policy-making of nature reserves in China and offers practical guidance for optimizing and adjusting sustainable agricultural development. The study emphasizes the vital functions of nature reserves in maintaining ecosystem balance, enhancing regional climate resilience, and serving as biodiversity reservoirs. This research offers strategic insights for integrating nature reserve spatial planning with sustainable agricultural development policies, providing a scientific basis for optimizing the eco-agricultural interface in China. Full article

Robots are increasingly emerging as effective platforms to overcome a wide range of challenges in agriculture. Beyond functioning as standalone systems, agricultural robots are proving valuable as collaborative platforms, capable of supporting and integrating with humans and other technologies and agricultural activities. In this study, we designed and implemented an automated system embedded in a ground-based robotic platform to support spraying drone operations. The system consists of a robotic platform that carries the spraying drone along with all necessary support devices, including a water tank, chemical reservoirs, a mixer, generators for drone battery charging, and a top landing pad. The system is controlled with a mobile app that calculates the total amount of water and chemicals required and sends commands to the platform to prepare the application mixture. The input information in the app includes the field area, application rate, and up to three chemical dosages simultaneously. Additionally, the platform allows the drone to take off from and land on it, enhancing both safety and operability. A set of pumps was used to deliver water and chemicals as specified in the mobile app. To automate pump control, we used Arduino technology, including both the microcontroller and a programming environment for coding and designing the mobile app. To validate the system’s effectiveness, we individually measured the amount of water and chemical delivered to the mixer tank and compared it with conventional manual methods for calculating chemical quantities and preparation time. The system demonstrated consistent results, achieving high precision and accuracy in delivering the correct amount. This study advances the field of agricultural robotics by highlighting the role of collaborative platforms. Particularly, the system presents a valuable and low-cost solution for small farms and experimental research. Full article

Surfactants can be utilized to improve oil recovery by changing the performance of reservoirs in rock pores. Kerogen is the primary organic matter in shale; however, high temperatures will affect the overall performance of this surfactant, resulting in a decrease in its activity or even failure. The effect of surfactants on kerogen pyrolysis has rarely been researched. Therefore, this study synthesized a polymeric surfactant (PS) with high temperature resistance and investigated its effect on kerogen pyrolysis under the friction of drill bits or pipes via molecular dynamics. The infrared spectra and thermogravimetric and molecular weight curves of the PS were researched, along with its surface tension, contact angle, and oil saturation measurements. The results showed that PS had a low molecular weight, with an MW value of 124,634, and good thermal stability, with a main degradation temperature of more than 300 °C. It could drop the surface tension of water to less than 25 mN·m⁻¹ at 25–150 °C, and the use of slats enhanced its surface activity. The PS also changed the contact angles from 127.96° to 57.59° on the surface of shale cores and reversed to a water-wet state. Additionally, PS reduced the saturated oil content of the shale core by half and promoted oil desorption, indicating a good cleaning effect on the shale oil reservoir. The kerogen molecules gradually broke down into smaller molecules and produced the final products, including methane and shale oil. The main reaction area in the system was the interface between kerogen and the surfactant, and the small molecules produced on the interface diffused to both ends. The kinetics of the reaction were controlled by two processes, namely, the step-by-step cleavage process of macromolecules and the side chain cleavage to produce smaller molecules in advance. PS could not only desorb oil in the core but also promote the pyrolysis of kerogen, suggesting that it has good potential for application in shale oil exploration and development. Full article

Based on drilling, core and seismic data, combined with the regional tectonic sedimentary evolution background, the sedimentary environment of the Triassic carbonate rocks in the Mangeshlak Basin was studied. A sedimentary facies model of this set of carbonate rocks was established. Research has shown that the Mangeshlak Basin underwent a complete large-scale marine transgression–regression sedimentary evolution process during the Triassic. During the early to middle Triassic, seawater gradually invaded the northwest region of the basin from northwest to southeast and gradually regressed in the late Middle Triassic. In the lower part of the Triassic carbonate rocks, the primary components are developed granular limestone or dolomite with oolitic structures, interspersed with a small amount of thin mudstone, which is a good reservoir; the upper part of the Triassic is mainly composed of sedimentary mudstone and mudstone, which can form good sealings. The hill-shaped reflections of the platform edge facies, along with the high-frequency, strong-amplitude, and moderately continuous reflections within the restricted platform interior, are clearly visible on the seismic profile. These features are consistent with the sedimentary environment and lithofacies characteristics revealed by drilling data along the profile. Drilling and seismic data revealed that the sedimentary environment of the early and middle Triassic in the basin is mainly composed of shallow water platform edges and restricted platforms, as well as carbonate rock slopes and open non-marine shelves in deep water areas. A sedimentary facies model of the Triassic carbonate rock segment in the basin was established, comprising restricted platforms, platform edges, carbonate rock slopes, and non-marine shelves. Unlike the modified Wilson marginal carbonate rock platform model, the carbonate rock platform edge in the Mangeshlak Basin does not develop reef facies. Instead, it is mainly composed of oolitic beach (dam) sediments, making it the most favorable sedimentary facies zone for the Triassic reservoir development in the basin. Full article

In this study, we analyzed the microearthquake seismicity in the Enguri area (Georgia) recorded between 2020 and 2023 using a newly installed seismic network developed within the DAMAST project. The high sensitivity of the network allowed the detection of even very small seismic events, enabling a detailed investigation of the temporal dynamics of local seismicity. Statistical analyses suggest that the seismic activity around the Enguri Dam is influenced by a combination of natural tectonic processes and subtle reservoir-induced stress changes. While the dam does not appear to exert strong seismic forcing, the observed ≈7-month delay between water level variations and seismicity may indicate a triggering effect. Localized stress variations and temporal clustering further support the hypothesis that water level fluctuations modulate seismic activity. Additionally, the mild persistence in interoccurrence times is consistent with a stress accumulation and delayed triggering mechanism associated with reservoir loading. Full article

Small reservoirs in hilly areas serve as critical water conservancy infrastructure, playing an essential role in flood control, irrigation, and regional water security. However, dam-break events pose significant risks to downstream urban areas, threatening the sustainability and resilience of cities. This study takes Guangyuan City as a case study and employs numerical simulation methods—including dam-break modeling, hydrological modeling, and hydrodynamic modeling—to analyze the impact of dam-break floods on downstream urban regions. The results reveal that dam failure in small reservoirs can cause peak flood velocities exceeding 15 m/s, severely endangering urban infrastructure, ecosystems, and public safety. Additionally, for reservoirs with large catchment areas, dam-break floods combined with rainfall-induced flash floods may create compound disaster effects, intensifying urban flood risks. These findings underscore the importance of sustainable reservoir management and integrated flood risk strategies to enhance urban resilience and reduce disaster vulnerability. This research contributes to sustainable development by providing scientific insights and practical support for flood risk mitigation and resilient infrastructure planning in mountainous regions. Full article

Increasing water demand and climate change exacerbate water management challenges in arid and semi-arid regions experiencing water scarcity resulting from low and irregular precipitation and high evapotranspiration. These regions rely on substantial water storage capacity, typically provided by large multi-purpose public reservoirs and small private reservoirs. While public reservoirs are typically monitored, the number, size, and private ownership of small reservoirs complicate effective storage monitoring, hindering efforts to assess water availability during droughts and to allocate water efficiently and equitably. Remote sensing provides a solution to complement existing monitoring systems by offering high spatial and temporal resolution observations. This study introduces a methodology for monitoring the surface area of large and small reservoirs based on optical and radar images from Sentinel-1 and Sentinel-2 satellites. The Normalized Difference Water Index (NDWI) and the Otsu image segmentation method are employed to identify and estimate water body areas, and the Google Earth Engine and programming languages are used to automate the process. The validation results demonstrated correlation for most reservoirs, with slight underestimations at flood peaks. Among the 17 large reservoirs, 16 had an R² value above 0.82, 12 had an RMSE value below 0.8, and 14 had a KGE value above 0.7. For the small reservoirs, the method correctly identified 3224 of the 6370 reservoirs recorded in situ, with greater accuracy in the classes of reservoirs with elevation above 10 m. A total of 7251 reservoirs were mapped, including 4027 not present in the database of the responsible regulatory entity, most with an area of less than 1.8 ha. Performance was better for larger areas (>3 ha), while small areas were underestimated. This methodology offers a practical water management tool adaptable for various-sized surface water bodies, including small, unmonitored water bodies. Full article

Background: Antimicrobial resistance is a pressing global concern affecting both human and animal health, with environment playing a key role in the dissemination of resistance determinants. This study aimed to investigate the presence of antimicrobial resistance genes (ARGs) associated with tetracyclines, β-lactams, macrolides, and sulfonamides in environmental matrices collected from 65 sheep and goat farms in central Portugal. Methods: Environmental samples, including water, soil, pasture, and bedding, were analyzed through qPCR for the detection of clinically relevant ARGs. Results: ARGs were detected in 83% of the samples, with over half exhibiting genes from three or more antibiotic classes, suggesting potential multidrug resistance. β-lactamase genes were the most prevalent, followed by those conferring resistance to tetracycline and sulfonamide resistance, while macrolide resistance genes were least frequent. The distribution of ARGs varied by farm type, host species, and municipality. Conclusions: These findings suggest that small ruminant farms serve as important reservoirs for ARGs. The results underscore the need for systematic surveillance and further research into the ecological and genetic factors driving ARG persistence and dissemination in extensive livestock systems, including proper waste management strategies to limit the spread and persistence of antibiotic resistance and mitigate broader public health risks. Full article

Hydraulic fracturing significantly impacts water production. This makes it crucial to determine whether its effects on formation water production are beneficial or detrimental in complex reservoir stimulations. This paper gives the influence that acts on pore structure variations and irreducible water transformation by hydraulic fracturing; by using NMR and Micro-CT, pore-throat reconfiguration in core samples induced fracturing. Two main pore variation types were identified from CT images. To analyze the gas–water flow mechanisms in pre-fracturing and post-fracturing reservoir conditions, we tested quantifying changes in irreducible water transforms into movable water saturation by using a triaxial in situ flow system, thereby elucidating the impact of the hydraulic fracture on irreducible water saturation. The experiments demonstrate that pore structures are significantly modified in terms of connectivity and diameter through hydraulic fracturing. During damage zone formation, 12.4–19.2% of small pores coalesce into larger pores through integration of isolated spaces. This variation enhances fluid mobility, transforms 1.38–11.61% of irreducible water, and decreases starting pressure gradients by 1 MPa/100 m to 0.1 MPa/100 m. Modified pore structure leads to the iso-permeability point shifting toward higher water saturation. The gas-phase relative permeability at irreducible water saturation is two times as high as that of the matrix sample. Fractured zones show a 20–23% conversion efficiency of irreducible to movable water. In addition, based on the results of experimental data, hydraulic fracturing increased water production by 3607 to 9163 m³. However, this effect is only maintained during the first 3 to 6 months post-fracture. These results quantify the transformation of irreducible water into movable water in hydraulic fracturing. This study provides key performance indicators for gas reservoir applications. Full article

Multispectral satellite imagery has been widely applied in water quality monitoring, but limitations in spatial–temporal resolution and acquisition delays often hinder accurate assessments in small water bodies. In this study, a DJI M600PRO UAV equipped with a Sequoia multispectral sensor was used to assess the water quality in Zhangshan Reservoir, a small inland reservoir in Chuzhou, Anhui, China. Two regression approaches—the Window Averaging Method (WAM) and the Matching Pixel-by-Pixel Method (MPP)—were used to link UAV-derived spectral indices with in situ measurements of total nitrogen (TN), total phosphorus (TP), and chemical oxygen demand (COD). Despite a limited sample size (n = 60) and single-day sampling, MPP outperformed WAM, achieving higher predictive accuracy (R² = 0.970 for TN, 0.902 for TP, and 0.695 for COD). The findings demonstrate that UAV-based MPP effectively captures fine-scale spatial heterogeneity and offers a promising solution for monitoring water quality in small and turbid reservoirs, overcoming key limitations of satellite-based remote sensing. However, the study is constrained by the temporal coverage and sample density, and future work should integrate multi-temporal UAV observations and expand the dataset to improve the model robustness and generalizability. Full article

In comparison with conventional hydrological parameters such as water levels and temperatures, geochemical changes induced by earthquakes have become increasingly important. It should be noted that hydrogen (δ²H) and oxygen isotopes (δ¹⁸O) offer the greatest potential as precursor proxies of earthquakes. Here, we conducted high-resolution sampling (weekly, 59 samples), measuring consecutive δ²H and δ¹⁸O levels at the two sites of the WLY well and SS spring in the Yan-Huai Basin of Beijing from June 2021 to June 2022. During the period of this sampling, several small earthquakes of ML > 1.6 occurred in Beijing. We used statistical methods (analysis of variance) to test the significant differences, used Self-Organizing Maps (SOMs) for data clustering, and then used Bayesian Mixing Models (MixSIAR) to calculate the proportions of the source contributions. We found significant four-stage patterns of change processes in δ²H and δ¹⁸O at both sites. The WLY well exhibited a distinct four-stage variation pattern: initial stable development (WT1) followed by a rapid rise (WT2) and sudden fall (WT3) before the small earthquakes, and finally gradual stabilization after earthquakes (WT4). In contrast, the SS spring displayed an inverse pattern, beginning with stable development (ST1), then undergoing a rapid falling (ST2) and sudden rising (ST3) before the small earthquakes, and finally stabilizing through stepwise reduction after the earthquakes (ST4). The most likely mechanisms were differences in the time of rupture between the carbonate in WLY and granite in SS under sustained stress. The stress induced source mixing of fluid from the surface or deeper groundwater-source reservoirs. The hypothesis was supported by the MixSIAR model, calculating the variational proportion of source contributions in the four stages. This work permitted the use of high-resolution isotopic data for statistical confirmation of concomitant shifts during the earthquakes, provided the mechanisms behind them, and highlighted the potential for the consecutive monitoring of hydrogen and oxygen isotopes indicators in earthquake-prediction studies. Full article

Hydrogeochemical characteristics and temperature variations in fault-controlled, deep-circulation thermal springs elucidate water–rock interaction dynamics and hydrothermal circulation depths, providing critical insights into fault permeability and stress accumulation. To investigate the coexistence of high-temperature and medium-low-temperature thermal springs on small-scale faults and their distinct circulation mechanisms, hydrochemical and isotopic analyses were conducted on 13 water samples (9 proximal on the Xiangbaihe Fault) in western Yunnan. The hot springs along the Xiangbaihe Fault are predominantly classified as the Na-HCO₃ type, derived from carbonate and aluminosilicate hydrolysis. δ²H and δ¹⁸O confirmed a meteoric origin, with recharge elevations spanning 2465–3286 m (Gaoligong Mountain). Inverse hydrochemical modeling demonstrated progressive mineral transfer and water–rock interactions along the fault’s east–west axis. Conservative elements (Cl, Li) suggested a shared geothermal fluid source or reservoir affiliation. BLZ reservoir temperatures (194–221 °C) were classified as a high-temperature system, whereas others (58–150 °C) represented medium-low-temperature systems. Although each thermal spring represents a distinct geothermal system, reservoir interconnectivity is inferred. Notably, despite uniform lithology, variations in spring temperature and elemental composition are attributed to a subsurface magma chamber beneath BLZ, heterogeneous fault geometries, differential reservoir temperatures, and variable cold-water mixing ratios. This study establishes a framework for understanding groundwater circulation in small-scale fault-associated geothermal systems, with implications for tectonic activity monitoring and geothermal resource assessment. Full article