Search Results (1,838)

Fumonisins, primarily produced by Fusarium spp. and Aspergillus section nigri, are common contaminants in maize, cereal grains, and other processed and derived products, representing a significant risk to food safety and public health. This study presents the development and optimisation of a high-performance liquid chromatography method with fluorescence detection (HPLC-FLD) for the quantification of fumonisin B1 (FB1) and B2 (FB2) in various food matrices. In contrast with conventional protocols employing potassium phosphate buffers as the mobile phase, the proposed method utilises formic acid, offering enhanced compatibility with liquid chromatography systems. An automated online precolumn derivatisation with o-phthaldialdehyde (OPA) was optimised through experimental design and response surface methodology, enabling baseline separation of FB1 and FB2 derivatives in less than 20 min. The method demonstrated high sensitivity, with limits of detection of 0.006 µg mL⁻¹ for FB1 and 0.012 µg mL⁻¹ for FB2, and excellent repeatability (intraday RSD values of 0.85% and 0.83%, respectively). Several solid-phase extraction (SPE) strategies were evaluated to enhance sample clean-up using a variety of food samples, including dried figs, raisins, dates, corn, cornmeal, wheat flour, and rice. FumoniStar Inmunoaffinity columns were the only clean-up method that provided optimal recoveries (70–120%) across all tested food matrices. However, the MultiSep™ 211 column yielded good recoveries for both fumonisins in dried figs and raisins. Additionally, the C18 cartridge achieved acceptable recoveries for both fumonisins in dried figs and wheat flour. Full article

In China’s Loess Plateau, sustainable agricultural end products are affected by an insufficiency of water resources. Rising crop water use efficiency (WUE) through field management pattern improvement is a crucial plan of action to address this issue. However, there is no agreement among researchers on the most appropriate field management practices regarding WUE, which requires further integrated quantitative analysis. We conducted a meta-analysis by quantifying the effect of agricultural practices surrounding nitrogen (N) fertilizer management. The two experimental cultivars were Yunhan–20410 and Yunhan–618. The subplots included nitrogen 0 kg·ha⁻¹ (N0), 90 kg·ha⁻¹ (N90), 180 kg·ha⁻¹ (N180), 210 kg·ha⁻¹ (N210), and 240 kg·ha⁻¹ (N240). Our results show that higher N rates (up to N210) enhanced water consumption during the node-flowering and flowering-maturity time periods. YH–618 showed higher water use during the sowing–greening and node-flowering periods but decreased use during the greening-node and flowering-maturity periods compared to YH–20410. The N210 treatment under YH–618 maximized water use efficiency (WUE). Increased N rates (N180–N210) decreased covering temperatures (T_max, T_min, T_aver) during flowering, increasing the level of grain filling. Spike numbers rose with N application, with an off-peak at N210 for strong-gluten wheat. The 1000-grain weight was at first enhanced but decreased at the far end of N180–N210. YH–618 with N210 achieved a harvest index (HI) similar to that of YH–20410 with N180, while excessive N (N240) or water reduced the HI. Dry matter accumulation increased up to N210, resulting in earlier stabilization. Soil water consumption from wintering to jointing was strongly correlated with pre-flowering dry matter biological process and yield, while jointing–flowering water use was linked to post-flowering dry matter and spike numbers. Post-flowering dry matter accumulation was critical for yield, whereas spike numbers positively impacted yield but negatively affected 1000-grain weight. In conclusion, our results provide evidence for determining suitable integrated agricultural establishment strategies to ensure efficient water use and sustainable production in the Loess Plateau region. Full article

Oolitic hematite ore represents a significant iron resource, but its utilization is challenging due to the complex multi-layered circular structure of hematite ore, which makes it difficult to be reduced. This study systematically investigated the phase transformation principle and magnetite grain growth law during the magnetization sintering of oolitic hematite ore, aiming to establish optimal conditions for efficient hematite ore to magnetite conversion. The results demonstrated that both elevated temperature and prolonged reduction duration significantly enhanced the reduction efficiency of hematite (Fe₂O₃) to magnetite. The optimal sintering conditions were determined to be 700 °C for 45 min, under which the magnetite content and Fe/O atomic ratio in the roasted products peaked at approximately 68% and 0.8%, respectively. However, temperatures exceeding 800 °C proved detrimental to magnetite formation, as further reduction to Fe_XO phases occurred. Notably, appropriate temperature elevation promoted substantial magnetite grain growth. When the sintering temperature increased from 600 °C to 700 °C, both the absolute and relative thickness of the magnetite layer exhibited remarkable enhancement, expanding from 9.52 μm to 76.76 μm and from 5.99% to 50.33%, respectively. Furthermore, comparative analysis revealed that a high sintering temperature for a short time was more effective for magnetite particle growth than a low temperature for a long time in the magnetization process of oolitic hematite ore. Full article

The development of technology has driven a rising need for high-accuracy and high-efficiency manufacturing of low-volume products. Incremental forming technology, characterized by die-free flexibility and low production costs, can effectively replace stamping processes for manufacturing customized small-batch products. However, high-performance aluminum alloys generally exhibit poor room-temperature plasticity but excellent high-temperature plasticity, necessitating the integration of thermal-assisted methods for manufacturing such products. However, the temperature of the forming region will excessively rise without temperature control, which will affect the forming performance of the material in hot incremental sheet forming of AA2024-T4 aluminum alloy. This study focuses on AA2024-T4 aluminum alloy and proposes a uniform temperature control method for the electric hot tube-assisted incremental sheet forming process, incorporating an adaptive fuzzy PID algorithm. The temperature difference of the forming region is lower than 6% under the various temperatures. On this basis, the forming limit angle and the microstructure state of the material are analyzed, and the grain feature of the material exhibits significantly refined grains and the uniform fine grain distribution under 180 °C with the temperature control of the adaptive fuzzy PID algorithm. Full article

This investigation employs focused ion beam (FIB) and transmission electron microscopy (TEM) techniques to systematically analyze the distribution characteristics of fission products in medium-burnup (40.6 GWd/tU) UO₂ fuel and their impact on fuel cracking behavior. The findings indicate that grain boundary embrittlement is predominantly attributed to the accumulation of spherical particles of solid fission products, including Mo, Ru, Rh, and Pd, which preferentially segregate around impurity particles, leading to localized stress concentration. Intragranular cracks are associated with the strip-like segregation of fission elements and the amorphization process. It also reveals that the size and number density of intragranular Xe bubbles are ~6.24 ± 0.24 nm and 5.2 × 10²² m⁻³, respectively, while Xe did not, under the analyzed conditions, significantly influence crack nucleation. This research elucidates the correlation mechanism between fission product distribution and fuel cracking behavior at medium burn up, offering experimental evidence to enhance the reliability and safety of nuclear fuel assemblies. Full article

A wide-bandgap AgInGaSe₂ (AIGS) thin film was fabricated using molecular beam epitaxy (MBE) via a three-stage method. The influence of Selenium (Se) pressure on the properties of AIGS films and solar cells was studied in detail. It was found that Se pressure played a very important role during the fabrication process, whereby Se pressure was varied from 0.8 × 10⁻³ Torr to 2.5 × 10⁻³ Torr in order to specify the effect of Se pressure. A two-stage mechanism during the production of AIGS solar cells was concluded according to the experimental results. With an increase in Se pressure, the grain size significantly increased due to the supply of the Ag–Se phase; the superficial roughness also increased. When Se pressure was increased to 2.1 × 10⁻³ Torr, the morphology of AIGS changed abruptly and clear grain boundaries were observed with a typical grain size of over 1.5 μm. AIGS films fabricated with a low Se pressure tended to show a higher bandgap due to the formation of anti-site defects such as In and Ga on Ag sites as a result of the insufficient Ag–Se phase. With an increase in Se pressure, the crystallinity of the AIGS film changed from the (220)-orientation to the (112)-orientation. When Se pressure was 2.1 × 10⁻³ Torr, the AIGS solar cell demonstrated its best performance of about 9.6% (Voc: 810.2 mV; Jsc: 16.7 mA/cm²; FF: 71.1%) with an area of 0.2 cm². Full article

An analysis of the existing methods of sintering diamond-containing composites is presented. On the basis of mathematical modeling and experimental studies, the conditions of the laser liquid-phase sintering of diamond-containing composites under which they retain their strength are determined. The energy and technological parameters of the laser irradiation process are characterized, which determine the range of laser processing modes within which no oxidation and crack formation occur, and a high-quality composite with specified geometrical parameters is formed. It has been proven that composites consisting of synthetic diamond grains and a metal bond do not lose strength under the condition that the temperature during laser heating does not exceed 1600 °C and the exposure time is 0.3 s. Electron microscopy and X-ray diffractometry were used for experimental studies of the microstructure and phase composition of the sintered layers. A new design and manufacturing method for a drum-type abrasive tool with replaceable diamond inserts for grinding large-sized aircraft and shipbuilding products are proposed. Components of a laser technological complex for the implementation of the process of sintering the diamond-containing layer of the abrasive inserts of the drum have been developed. Full article

Phonolite is a fine-grained, shallow extrusive rock rich in alkali minerals and containing iron/titanium-bearing minerals. This rock is widely used as a construction material for building exteriors due to its excellent abrasion resistance and insulation properties. However, during the cutting process, approximately 70% of the rock is discarded as tailing. So, this study aims to repurpose tailings from a phonolite cutting and sizing plant into a high-alkali ceramic raw mineral concentrate. To enable the use of phonolite tailings in ceramic manufacturing, it is necessary to remove coloring iron/titanium-bearing minerals, which negatively affect the final product. To achieve this removal, dry/wet magnetic separation processes, along with flotation, were employed both individually and in combination. The results demonstrated that using dry high-intensity magnetic separation (DHIMS) resulted in a concentrate with an Fe₂O₃ + TiO₂ grade of 0.95% and a removal efficiency of 85%. The wet high-intensity magnetic separation (WHIMS) process reduced the Fe₂O₃ + TiO₂ grade of the concentrate to 1.2%, with 70% removal efficiency. During flotation tests, both pH levels and collector concentration impacted the efficiency and Fe₂O₃ + TiO₂ grade (%) of the concentrate. The lowest Fe₂O₃ + TiO₂ grade of 1.65% was achieved at a pH level of 10 with a collector concentration of 2000 g/t. Flotation concentrates processed with DHIMS achieved a minimum Fe₂O₃ + TiO₂ grade of 0.90%, while those processed with WHIMS exhibited higher Fe₂O₃ + TiO₂ grades (>1.1%) and higher recovery rates (80%). Additionally, studies on flotation applied to WHIMS concentrates showed that collector concentration, pulp density, and conditioning time significantly influenced the Fe₂O₃ + TiO₂ grade of the final concentrate. Full article

The nutritional and quality characteristics of improved vegetable soybean genotypes were evaluated and compared with those of a grain-type soybean at the R6 (green maturity) and R8 (physiological maturity) stages. Significant variation (p < 0.05) was observed among genotypes for all measured traits. The overall quality parameters increased from the R6 (green maturity) stage to the R8 (physiological maturity) stage. Among the R6-stage genotypes, AVSB2001 recorded the highest contents of protein (15.30 ± 0.57 g/100 g), ash (2.31 ± 0.06 g/100 g), fat (8.05 ± 0.17 g/100 g), and calcium (140.78 ± 0.97 mg/100 g). The genotype Karune exhibited significantly higher levels of total sugars, non-reducing sugars, iron, and magnesium than the other entries. At the R8 stage, Swarna Vasundhara showed the highest protein content (39.23%), while AGS 447 recorded the highest values for fat, total sugars, in vitro protein digestibility, iron, copper, magnesium, and manganese. Notably, in vitro protein digestibility was lower across all genotypes at the R8 stage compared to the R6 stage. These findings suggest that selected vegetable soybean genotypes possess substantial nutritional value and can contribute meaningfully to meeting the recommended dietary allowance (RDA) across different age and occupational groups, underscoring this research’s potential public health impact. Based on stage-specific quality profiles, R6-stage genotypes may be better suited for fresh vegetables, whereas R8-stage genotypes can be utilized similarly to grain-type soybean for processing into products such as dhal, oil, flour, and other value-added foods. Full article

Tight gas is an unconventional resource abundantly found in low-porosity, low-permeability sandstone reservoirs. Production can be significantly reduced due to water production during the development process. Therefore, it is necessary to predict water production during the logging phase to formulate development strategies for tight gas wells. This study analyzes the water production mechanism in tight sandstone reservoirs and identifies that the core of water production evaluation in the Shihezi Formation of the Linxing block is to clarify the pore permeability structure of tight sandstone and the type of intra-layer water. The primary challenge lies in the accurate characterization of bound water saturation. By integrating logging data with core experiments, a bound water saturation evaluation model based on grain size diameter and pore structure index was established, achieving a calculation accuracy of 92% for the multi-parameter-fitted bound water saturation. Then, based on the high-precision bound water saturation, a gas–water ratio prediction model for the first month of production, considering water saturation, grain size diameter, and fluid type, was established, improving the prediction accuracy to 87.7%. The bound water saturation evaluation and water production evaluation models in this study can achieve effective water production prediction in the early stage of production, providing theoretical support for the scientific development of tight gas in the Linxing block. Full article

Stylolites are ubiquitous diagenetic products in carbonate rocks. They play a significant role in enhancing or reducing fluid flow in subsurface reservoirs. This study unravels the relationship between stylolite networks, carbonate microfacies, and the elemental geochemistry of Upper Cretaceous limestones of the Kometan Formation (shallow to moderately deep marine) in Northern Iraq. Stylolites exhibit diverse morphologies across mud- and grain-supported limestone facies. Statistical analyses of stylolite spacing, wavelength, amplitude, and their intersections and connectivity indicate that grain size, sorting, and mineral composition are key parameters that determine the geometrical properties of the stylolites and stylolite networks. Stylolites typically exhibit weak connectivity and considerable vertical spacing when hosted in packstone facies with moderate grain sorting. Conversely, mud-supported limestones, marked by poor sorting and high textural heterogeneity, host well-developed stylolite networks characterized by high amplitude and frequent intersections, indicating significant dissolution and deformation processes. Stylolites in mud-supported facies are closely spaced and present heightened amplitudes and intensified junctions, with suture and sharp-peak type. This study unveils that stylolites can potentially enhance porosity in the studied formation. Full article

With the swift progression of the High-Standard Farmland Construction Program in China and worldwide, many dryland wheat fields can be irrigated once during the wheat growth stage (one-off irrigation). However, the combined strategies of one-off irrigation, tillage, and N management for augmenting wheat grain yield and quality are still undeveloped in drought regions. Two-site split–split field experiments were conducted to study the impacts of irrigation, tillage, and N management and their combined effects on grain yield; the contents of protein and protein components; processing quality; and the characteristics of N accumulation and translocation in wheat from a typical dryland wheat production area in China from 2020 to 2022. The irrigation practices (I0, zero irrigation and I1, one-off irrigation), tillage methods (RT, rotary tillage; PT, plowing; and SS, subsoiling) and N management (N0, N120, N180, and N240) were applied to the main plots, subplots and sub-subplots, respectively. The experimental sites, experimental years, irrigation practices, tillage methods, and N management methods and their interaction significantly affected the yield, quality, and plant N characteristics of wheat in most cases. Compared to zero irrigation, one-off irrigation significantly increased the plant N accumulation, enhancing grain yield by 33.7% while decreasing the contents of total protein, albumin, globulin, gliadin, and glutenin by 4.4%, 6.4%, 8.0%, 12.2%, and 10.0%, respectively. It also decreased the wet gluten content, stability time, sedimentation value, extensibility by 4.1%, 10.7%, 9.7%, and 5.5%, respectively, averaged across sites and years. Subsoiling simultaneously enhanced the aforementioned indicators compared to rotary tillage and plowing in most sites and years. With the increase in N rates, wheat yield firstly increased and then decreased under zero irrigation combined with rotary tillage, while it gradually increased when one-off irrigation was combined with subsoiling; however, the contents of total protein and protein components and the quality tended to increase firstly and then stabilize regardless of irrigation practices and tillage methods. The correlations of yield and quality indicators with plant N characteristics were negative when using distinct irrigation practices and tillage methods, while they were positive under varying N management. The decrease in wheat quality induced by one-off irrigation could be alleviated by optimizing N management. I1STN180 exhibited higher yield, plant N accumulation and translocation, and better quality in most cases; thus, all metrics of wheat quality were significantly increased, with a yield enhancement of 50.3% compared to I0RTN180. Therefore, one-off irrigation with subsoiling and an N rate of 180 kg ha⁻¹ is an optimal strategy for high yield, high protein, and high quality in dryland wheat production systems where one-off irrigation is assured. Full article

Grain drying technology is a core process for ensuring food quality, extending storage life, and improving processing adaptability. With the continuous growth of global food demand and the increasing requirements for food quality and energy efficiency, traditional drying technologies face multiple challenges. This paper reviews six major grain drying technologies, comprising hot air drying, microwave drying, infrared drying, freeze drying, vacuum drying, and solar drying. It provides an in-depth discussion of the working principles, advantages, and limitations of each technology, and analyzes their performance in practical applications. In response to challenges such as high energy consumption, uneven drying, and quality loss during the drying process, the paper also explores the research progress of several hybrid drying systems, such as microwave–hot air drying combined systems and solar–infrared drying systems. Although these emerging technologies show significant potential in improving drying efficiency, energy saving, and maintaining food quality, their high costs, scalability, and process stability still limit large-scale applications. Therefore, future research should focus on reducing energy consumption, improving drying precision, and optimizing drying system integration, particularly by introducing intelligent control systems. This would maximize the preservation of food quality while improving the system’s economic efficiency and sustainability, promoting innovation in food production and processing technologies, and further advancing global food security and sustainable agricultural development. Full article

The prediction of microstructure evolution during thermal processing plays a crucial role in tailoring the mechanical properties of metallic components. Therefore, this work presents a comprehensive, multiscale modelling approach to simulating phase transformations in large-diameter steel rings during cooling. A finite-element-based thermal model was first used to simulate transient temperature distributions in a large-diameter ring under different cooling conditions, including air and water quenching. These thermal histories were subsequently employed in two complementary phase transformation models of different levels of complexity. The Avrami model provides a first-order approximation of the evolution of phase volume fractions, while a complex full-field cellular automata approach explicitly simulates the nucleation and growth of ferrite grains at the microstructural level, incorporating local kinetics and microstructural heterogeneities. The results highlight the sensitivity of final grain morphology to local cooling rates within the ring and initial austenite grain sizes. Simulations demonstrated the formation of heterogeneous microstructures, particularly pronounced in the ring’s surface region, due to sharp thermal gradients. This approach offers valuable insights for optimising heat treatment conditions to obtain high-quality large-diameter ring products. Full article

In recent decades, the automotive industry has faced challenges around improving energy efficiency, reducing pollutant emissions, increasing occupant safety, and reducing production costs. To solve these challenges, it is necessary to reduce the weight of vehicle bodies. In this way, the steel industry has developed more efficient metal alloys. To combine vehicle mass reduction with improved performance in deformations in cases of impact, a new family of advanced steels is present, AHSS (Advanced High-Strength Steels). However, this family of steels has lower formability and greater springback compared to conventional steels; if it is not properly controlled, it will directly affect the accuracy of the product and its quality. Different regions of a stamped component, such as the flange, the body wall, and the punch pole, are subjected to different states of stress and deformation, determined by numerous process variables, such as friction/lubrication and tool geometry, in addition to blank holder force and drawbead geometry, which induce the material to different deformation modes. Thus, it is understood that the degree of work hardening in each of these regions can be evaluated by grain morphology and material hardening, defining critical regions of embrittlement that, consequently, will affect the material’s stampability. This work aims to study the formability of the cold-formed DP600 steel sheets in the die radius region using a Modified Nakazima test, varying drawbead geometry, followed by a nanohardness evaluation and material characterization through the electron backscatter diffraction (EBSD). The main objective is to analyze the work hardening in the critical blank regions by applying these techniques. The nanoindentation evaluations were consistent in die radius and demonstrated the hardening influence, proving that the circular drawbead presented the most uniform hardness variation along the profile of the stamped blank and presented lower hardness values in relation to the other geometries, concluding that the drawbead attenuates this variation, contributing to better sheet formability, which corroborates the Forming Limit Curve results. Full article