Search Results (172)

Microbially induced calcium carbonate precipitation (MICP) has emerged as a research focus in concrete crack remediation due to its environmental compatibility and efficient mineralization capacity. The hypersaline conditions of seawater (average 35 g/L NaCl) and alkaline environments (pH 12) within concrete cracks pose significant challenges to the survival of mineralization-capable microorganisms. To enhance microbial tolerance under these extreme conditions, this study employed a laboratory adaptive evolution strategy to successfully develop a Sporosarcina pasteurii strain demonstrating tolerance to 35 g/L NaCl and pH 12. Comparative analysis of growth characteristics (OD₆₀₀), pH variation, urease activity, and specific urease activity revealed that the evolved strain maintained growth kinetics under harsh conditions comparable to the parental strain under normal conditions. Subsequent evaluations demonstrated the evolved strain’s superior salt–alkali tolerance through enhanced enzymatic activity, precipitation yield, particle size distribution, crystal morphology, and microstructure characterization under various saline–alkaline conditions. Whole-genome sequencing identified five non-synonymous mutated genes associated with ribosomal stability, transmembrane transport, and osmoprotectant synthesis. Transcriptomic profiling revealed 1082 deferentially expressed genes (543 upregulated, 539 downregulated), predominantly involved in ribosomal biogenesis, porphyrin metabolism, oxidative phosphorylation, tricarboxylic acid (TCA) cycle, and amino acid metabolism. In concrete remediation experiments, the evolved strain achieved superior performance with 89.3% compressive strength recovery and 48% reduction in water absorption rate. This study elucidates the molecular mechanisms underlying S. pasteurii’s salt–alkali tolerance and validates its potential application in the remediation of marine engineering. Full article

Despite the development of a wide plethora of different anticancer agents, most of them are not used for patient treatment due to adverse effects caused by untargeted cytotoxicity. To prevent this unwanted toxicity, it is necessary to develop therapies discriminating between healthy and cancerous cells. One possible method is to target proteins overexpressed in cancer but not in normal cells. CD320 is a receptor responsible for the uptake of the transcobalamin-bound fraction of vitamin B12 (cobalamin), which is necessary for DNA synthesis, and thus, cell proliferation. CD320 was shown to be overexpressed in many cancers and its potential role as an early cancer biomarker was confirmed in several studies. Consequently, CD320 may represent a promising anti-cancer therapy target. This review summarizes the current advances and perspectives of anti-cancer CD320 targeting therapy, including therapeutic conjugates of vitamin B12, CD320-specific antibodies and nanobodies, nanoparticles loaded with cytotoxic drugs, porphyrin, and the potential of targeted CD320 therapy in attenuation of tumor tissues. Given the growing interest in CD320 as a novel target for anti-cancer therapy, further in vivo studies are required for the investigation of CD320 targeting effects on systemic cytotoxicity. Full article

A series of porphyrinoids fused to highly electron-withdrawing bis(thiadiazolo)benzene units have been prepared and spectroscopically characterized. These structures have modified chromophores and exhibit large bathochromic shifts. The nickel(II), copper(II) and zinc complexes of a bis(thiadiazolo)benzoporphyrin were prepared, and these showed strong absorptions above 600 nm that shifted to longer wavelengths with increasing atomic number for the coordinated metal cations. Although the investigated porphyrinoids were poorly soluble, proton NMR data could be obtained, and these demonstrated that the structures possess global aromatic character. This was confirmed with nucleus-independent chemical shift (NICS) calculations and anisotropy of induced current density (AICD) plots. The AICD plots also demonstrate that the fused heterocyclic unit is disconnected from the porphyrinoid π-system, and in this respect, it differs from phenanthroline-fused porphyrinoids as it shows the presence of extended conjugation pathways. Full article

Significant research has focused on cost–effective, highly active, and exceptionally stable non–noble metal electrocatalysts (NNMEs) to boost the performance of the oxygen reduction reaction (ORR). Of note, the development of design and synthesis of Fe–N–C electrocatalysts is essential but remains challenging. Herein, the Fe and N co–doped porous carbon material with a yolk–shell (YS) structure, termed SA–H₂TPyP@PDA–Fe (900), was fabricated by self–assembly of metal–free porphyrin as a yolk and polymerization of dopamine as a shell with an addition of iron salts, followed by the high–temperature pyrolysis and acid–leaching. As a result, active sites, like FeN₄ and N–doped C, within rich porous YS carbon structures, play an important role for ORR in an alkaline media. The SA–H₂TPyP@PDA–Fe (900) electrocatalyst shows positive ORR performances than those of SA–H₂TPyP (900) and SA–H₂TPyP@PDA (900), indicating the dominating function of the YS carbon structure decorated with Fe–based species. This efficient route of template–free–induced preparation of the YS structure discovers the design and synthesis of NNMEs for ORR. Full article

Photocatalytic H₂ production is one of the most promising approaches for sustainable energy. The literature presents a plethora of carefully designed systems aimed at harnessing solar energy and converting it into chemical energy. However, the main drawback of the reported photocatalysts is their stability. Thus, the development of a cost-effective and stable photocatalyst, suitable for real-world applications remains a challenge. An ideal photocatalyst for H₂ production must possess appropriate band-edge energy positions, an effective sacrificial agent, and a suitable cocatalyst. Among the various photocatalysts studied, TiO₂ stands out due to its stability, abundance, and non-toxicity. However, its efficiency in the visible spectrum is limited by its wide bandgap. Metal doping is an effective strategy to enhance electron–hole separation and improve light absorption efficiency, thereby boosting H₂ synthesis. Common metal cocatalysts used as TiO₂ dopants include platinum (Pt), gold (Au), copper (Cu), nickel (Ni), cobalt (Co), ruthenium (Ru), iron (Fe), and silver (Ag), as well as bimetallic combinations such as Ni-Fe, Ni-Cu, Nb-Ta, and Ni-Pt. In all cases, doped TiO₂ exhibits higher H₂ production performance compared to undoped TiO₂, as metals provide additional reaction sites and enhance charge separation. The use of bimetallic dopants further optimizes the hydrogen evolution reaction. Additionally, porphyrins, with their strong visible light absorption and efficient electron transfer properties, have demonstrated potential in TiO₂ photocatalysis. Their incorporation expands the photocatalyst’s light absorption range into the visible spectrum, enhancing H₂ production efficiency. This review paper explores the principles and advancements in metal- and porphyrin-doped TiO₂ photocatalysts, highlighting their potential for sustainable hydrogen production. Full article

In this work, we describe the synthesis of three new meso-arylporphyrins, named meso-tetrakis [4-(nicotinoyloxy)phenyl] porphyrin (H₂TNPP), meso-tetrakis [4-(picolinoyloxy)phenyl] porphyrin (H₂TPPP), and meso-tetrakis [4-(isonicotinoyloxy) phenyl] porphyrin (H₂TIPP). These new synthesized meso-arylporphyrins are characterized using spectroscopic analysis: Fourier Transform Infrared Spectroscopy (FTIR) and One-dimensional Nuclear Magnetic Resonance (1D NMR), and mass spectrometry (MS). The photophysical studies (UV–visible absorption, singlet oxygen (¹O₂) luminescence, and fluorescence emissions) demonstrate their potential uses as photosensitizers (PSs) in photodynamic therapy (PDT) applications. An in vitro investigation of the anti-fungal activity of H₂TNPP, H₂TPPP, and H₂TIPP against Candida (C.) species (C. albicans, C. glabrata, and C. tropicalis) reveals that their minimum inhibitory concentration (MIC) values ranged from 1.25 to 5 mg/mL. In addition, their in vitro anti-fungal susceptibilities against three dermatophyte clinical isolates (Trichophyton rubrum, Microsporum canis, and Trichophyton mentagrophytes) are also evaluated and they demonstrate good anti-fungal activities. A molecular docking study of these meso-arylporphyrins as anti-fungal agents against C. tropicalis extracellular aspartic proteinases, Protein data Bank in Europe (PDBe code: 1J71) and Trichophyton rubrum Sialidases (PDBe code: 7P1D) underlines the possible interactions of H₂TNPP, H₂TPPP, and H₂TIPP with the key amino acid residues of these fungal target proteins. Full article

Background: Heme is an important cofactor and plays crucial roles in the correct folding of hemoproteins. The synthesis of heme can be enhanced by the plasmid-based expression of heme biosynthetic genes. However, plasmid-based expression is genetically unstable and requires the utilization of antibiotics to maintain high copy numbers of plasmids. Methods: The rate-limiting steps in heme biosynthesis were first analyzed based on previous studies and the accumulation of heme intermediates was achieved by adding heme precursor (5-aminolevulinic acid, ALA). Next, the intracellular accumulation of porphyrin was increased by deleting the porphyrin transporter TolC. Finally, the heme synthetic genes were modified by integrating the hemA and hemL genes into the cheW and yciQ locus, assembling the rate-limiting enzymes HemC and HemD with RIAD-RIDD tags, replacing the promoters of hemE/hemH genes with the constitutive promoter P_J23100, and deleting the heme degradation gene yfeX. Results: An enhanced heme supply HEME2 strain was obtained with a heme titer of 0.14 mg/L, which was 4.60-fold higher than that of the C41(DE3) strain. The HEME2 strain was applied to produce human hemoglobin and leghemoglobin. The titer and peroxidase activity of human hemoglobin were 1.29-fold and 42.4% higher in the HEME2-hHb strain than the values in the control strain C41-hHb. In addition, the peroxidase activity and heme content of leghemoglobin were increased by 39.2% and 53.4% in the HEME2-sHb strain compared to the values in the control strain C41-sHb. Conclusions: A plasmid-free Escherichia coli C41(DE3) strain capable of efficient and stable heme supply was constructed and can be used for the production of high-active hemoglobins. Full article

Over the past two decades, the application of photocatalytic reactions in organic synthesis has increased remarkably. Porphyrins, renowned for their exceptional photophysical properties, photostability, and prevalence in natural catalytic processes, are attracting significant attention as promising photocatalysts for reactions proceeding through energy transfer and one-electron transfer. In this work, we synthesized the indium(III) complex of 2-[4-(diethoxyphosphoryl)phenyl]-1H-imidazo[4,5-b]-5,10,15,20-tetramesitylporphyrin (InTMPIP) and explored its application as a photocatalyst for the oxidation of sulfides by dioxygen or air. Complex InTMPIP was found to generate singlet oxygen with quantum yield of 0.92 (toluene) and enables efficient photooxidation of sulfides to sulfoxides by dioxygen in “green” acetonitrile/water (4:1 v/v) or methanol/chloroform (2:1 v/v) solvent mixtures with almost quantitative yield. Furthermore, InTMPIP was grafted onto hydrated mesoporous titania and materials InTMPIP/TiO₂-1 and InTMPIP/TiO₂-2 with different In/Ti ratios were obtained and investigated. The composition and structure of the materials were studied using a combination of elemental analysis, various spectroscopic methods, gas adsorption measurements, and SEM imaging. Finally, the photocatalytic efficiency of InTMPIP/TiO₂-2 was explored in aerobic photooxidation of sulfides. The heterogenized complex enables selective synthesis of sulfoxides under “green” conditions; however, it is prone to leaching into the solution when irradiated with both blue and red LEDs. Full article

New tetrasubstituted porphyrin tin complexes (5–14) were prepared in two different ways: In the first preparation procedure, tin porphyrin complexes were prepared by a direct reaction of butyltin trichloride and dibutyltin dichloride with tetra/tetrakis(4-X-phenyl)porphyrins (X = H, F, Cl, Br, CF₃, CH₃O, and (CH₃)₂N). In the second procedure, the same tin porphyrin complexes were synthesized from the reaction of butyltin trichloride and dibutyltin dichloride with lithium porphyrinato derivatives. These novel tin complexes were characterized by elemental analysis, ¹H, ¹³C NMR, FTIR, UV-Vis spectroscopy, and mass spectrometry. Among these complexes, tin porphyrin containing methoxy group [Bu₂Sn(TMOPP)] was tested as an adsorbent to remove tetracycline antibiotics from wastewater. The TTC antibiotic removal efficiency (R%) of this complex was measured using UV-Vis spectroscopy. After 120 min of equilibration, the final R% and adsorption capacity (q_t) were measured at 60.15% and 18.10 mg/g, respectively. Full article

Porphyrin’s excellent biocompatibility and modifiability make it a widely studied photoactive material. However, its large π-bond conjugated structure leads to aggregation and precipitation in physiological solutions, limiting the biomedical applications of porphyrin-based photoactive materials. It has been demonstrated through research that fabricating porphyrin molecules into nanoscale covalent organic frameworks (COFs) structures can circumvent issues such as poor dispersibility resulting from hydrophobicity, thereby significantly augmenting the photoactivity of porphyrin materials. Porphyrin-based COF materials can exert combined photodynamic and photothermal effects, circumventing the limitations of photodynamic therapy (PDT) due to hypoxia and issues in photothermal therapy (PTT) from heat shock proteins or the adverse impact of excessive heat on the protein activity of normal tissue. Furthermore, the porous structure of porphyrin COFs facilitates the circulation of oxygen molecules and reactive oxygen species and promotes sufficient contact with the lesion site for therapeutic functions. This review covers recent progress regarding porphyrin-based COFs in treating malignant tumors and venous thrombosis and for antibacterial and anti-inflammatory uses via combined PDT and PTT. By summarizing relevant design strategies, ranging from molecular design to functional application, this review provides a reference basis for the enhanced phototherapy application of porphyrin-based COFs as photoactive materials. This review aims to offer valuable insights for more effective biomedical applications of porphyrin-based COFs through the synthesis of existing experimental data, thereby paving the way for their future preclinical utilization. Full article

The oxygen reduction reaction (ORR) is one of the most critical reactions in energy conversion systems, and it facilitates the efficient conversion of chemical energy into electrical energy, which is necessary for modern technology. Developing efficient and cost-effective catalysts for ORRs is crucial for advancing and effectively applying renewable energy technologies such as fuel cells, metal–air batteries, and electrochemical sensors. In recent years, iron porphyrin-based composites have emerged as ideal catalysts for facilitating effective ORRs due to their unique structural characteristics, abundance, advances in synthesis, and excellent catalytic properties, which mimic natural enzymatic systems. However, many articles have focused on reviewing porphyrin-based frameworks or metalloporphyrins in general, necessitating research specifically addressing iron porphyrin. This review discusses iron porphyrin as an effective catalyst in ORRs. It provides a comprehensive knowledge of the application of iron porphyrin-based composites for electrocatalytic ORRs, focusing on their properties, synthesis, structural integration with conductive supports, catalytic mechanism, and efficacy. This review also discusses the challenges of applying iron porphyrin-based composites and provides recommendations to address these challenges. Full article

Titanium nitride and vanadium nitride–carbon-based composite systems, TiN/C and VN/C, were prepared using a new synthesis method based on the thermal decomposition of titanyl tetraphenyl porphyrin (TiOTPP) and vanadyl tetraphenyl porphyrin (VOTPP), respectively. The structure of the TiN/C and VN/C composite materials, as well as their precursors, were characterized using Fourier Transformed Infrared Spectroscopy, X-Ray diffraction (XRD), X-Ray energy dispersive (EDS) and X-Ray photoelectron spectroscopy (XPS). Morphologies of the TiN/C and VN/C composites were examined by means of scanning electron (SEM) and transmission electron (TEM) microscopy. The synthesis of the non-metalated tetraphenyl porphyrin, the titanium, and vanadium tetraphenyl porphyrin complexes were confirmed using FTIR. The thermal decomposition of the titanium and vanadium tetraphenyl porphyrin complexes produced the respective metal nitride encapsulated in a carbon matrix; this was confirmed by XRD, SEM, TEM, and XPS. From the XRD patterns, it was determined that the TiN and VN were presented in cubic form with expected space group FM-3M and 1:1 (metal:N) stoichiometry. The XPS results confirmed the presence of both TiN and VN in the carbon matrix without metal carbides. The SEM and TEM results showed that both TiN and VN nanoparticles formed small clusters throughout the carbon matrix; the EDS results revealed a uniform composition. The synthesis method presented in this work is novel and serves as an effective means to produce TiN and VN NPs with good structure and morphology embedded in a carbon matrix. Full article

Different approaches were evaluated to obtain 5,15-bis [4-(N,N-diphenyl)aminophenyl]-10,20-bis(pentafluorophenyl)porphyrin and 5,15-bis [4-(9-carbazolyl)phenyl]-10,20-bis(pentafluorophenyl)porphyrin. First, the reaction of 5-pentafluorophenyldypyrromethane with the corresponding benzaldehyde catalyzed by boron trifluoride diethyl etherate in dichloromethane led to a high level of scrambling that produced a mixture of porphyrins. These products involve ABAB (3%), A₃B (15%), and A₄ (4%) symmetries, where A represents a pentafluorophenyl group. These porphyrins have similar polarities and they are very difficult to separate by column chromatography. Therefore, the reagents were changed to pentafluorobenzaldehyde and dipyrromethane. When a 0.5:1 molar ratio was used, A₄ porphyrin was not obtained, and the main products were ABAB (19%) and A₃B (6%). Therefore, condensation of a dipyrromethane with pentafluorobenzaldehyde provides a general method for the rational synthesis of ABAB-porphyrins in good yield with lower scrambling. Full article

In the current work, chloro(meso-tetrakis(phenyl)porphyrin) manganese(III) [Mn(TPP)Cl] was synthesized following two steps: the preparation of meso-tetraphenylporphyrin (H_⁠2TPP) and the insertion of manganese into the free porphyrin H₂TPP. The compounds were characterized using SEM, FT-IR, UV, TGA/DTA, and XRD analyses. Manganese(III) meso-porphyrins exhibited hyper-type electronic spectra with a half-vacant metal orbital with symmetry, such as [dπ:dxz and dyz]. The thermal behavior of [Mn(TPP)(Cl)] changed (three-step degradation process) compared to the initial H₂TPP (one-step degradation process), confirming the insertion of manganese into the core of the free porphyrin H₂TPP. Furthermore, [Mn(TPP)Cl] was used to degrade calmagite (an azo dye) using H₂O₂ as an oxidant. The effects of dye concentration, reaction time, H₂O₂ dose, and temperature were investigated. The azo dye solution was completely degraded in the presence of [Mn(TPP)(Cl)]/H₂O₂ at pH = 6, temperature = 20 °C, C₀ = 30 mg/L, and H₂O₂ = 40 mL/L. The computed low activation energy (Ea = 10.55 Kj/mol) demonstrated the efficiency of the proposed catalytic system for the azo dye degradation. Overall, based on the synthesis process and the excellent catalytic results, the prepared [Mn(TPP)Cl] could be used as an effective catalyst for the treatment of calmagite-contaminated effluents. Full article

Photodynamic therapy (PDT) is a promising cancer treatment method that uses photosensitizing (PS) compounds to selectively destroy tumor cells using laser light. This review discusses the main advantages of PDT, such as its low invasiveness, minimal systemic toxicity and low risk of complications. Special attention is paid to photosensitizers obtained by chemical synthesis. Three generations of photosensitizers are presented, starting with the first, based on porphyrins, through the second generation, including modified porphyrins, chlorins, 5-aminolevulinic acid (ALA) and its derivative hexyl aminolevulinate (HAL), to the third generation, which is based on the use of nanotechnology to increase the selectivity of therapy. In addition, current research trends are highlighted, including the search for new photosensitizers that can overcome the limitations of existing therapies, such as heavy-atom-free nonporphyrinoid photosensitizers, antibody–drug conjugates (ADCs) or photosensitizers with a near-infrared (NIR) absorption peak. Finally, the prospects for the development of PDTs are presented, taking into account advances in nanotechnology and biomedical engineering. The references include both older and newer works. In many cases, when writing about a given group of first- or second-generation photosensitizers, older publications are used because the properties of the compounds described therein have not changed over the years. Moreover, older articles provide information that serves as an introduction to a given group of drugs. Full article